Search Documents

By Fred D. Fox

INTRODUCTION Approximately two years have elapsed since the first summary of the Grizzly Gulch Tailings Disposal Project was presented (1). Since that time, various physical modifications and additions to the existing treatment system have transpired. Further, Homestake and the entire mining industry have been impacted severely by additional modifications and additions concerning regulatory reform aimed at total disciplinary permitting and hazardous waste management. The following paper summarizes the past accomplishments relating to the Grizzly Gulch Tailings Disposal Project, correlating these accomplishments with future plans that are being developed to comply with regulations and to continue Homestake's commitment to environmental protection. The famous Homestake Gold Mine, located in Lead, South Dakota, has been operating in the Black Hills region for over a century, approximately 12 years before the south half of Dakota Territory was admitted to the Union as the State of South Dakota (2). During the 104 years of operational development, Homestake's Gold Mine, as well as the entire mining industry, have been influenced by numerous governmental regulations dating back to the Refuse Act of 1899 which regulated the deposit of debris from mines and stamp works. The enactment of the National Environmental Policy Act of 1969 may be thought of as the beginning of a long line of unplanned steps to deal with the many concerns of matters pertaining to the environment. Environmental awareness continued into the 1970’s, in which the Clean Air Act, Federal Water Pollution Control Act, Safe Drinking Water Act, Toxic Substances Control Act, and the Resource Conservation and Recovery Act (RCRA), to name a few, surfaced.

Jan 1, 1983

By Ray Slavin, Remi Proulx

The Meikle Mine is a mature underground gold mine utilizing primary and secondary longhole open stoping method with delayed backfill. Combined production with the newly developed Rodeo Mine is 4700 tons per day (4265 tonnes per day) of ore. The vast majority of Meikle Mine production comes from secondary and remnant stope blocks. Remnant stopes are ore blocks that were left behind in the initial mining sequence due to various reasons. Mining of these remnant blocks has created many challenging blasting situations. The application of electronic initiation to blast remnant stopes has proven extremely beneficial. Electronic initiation has provided the blasting engineer with a high degree of flexibility with respect to timing to successfully extract these difficult stopes. Post blast assessment of the remnant stopes using the mine’s cavity monitoring system (CMS) demonstrates that the mine is maximizing ore recovery and minimizing waste dilution. The largest remnant stope blast to date required 54 holes and produced 6700 tons (6075 tonnes) of ore. Another area where the application of electronic detonators has proved successful is in the extraction of slots in which ground conditions are extremely poor. Taking the slot blasts in one shot with double-decked holes as opposed to two single-decked shots has eliminated the need to clean and or re-drill holes. The ability to open the slots in one blast has helped reduce the total mining cost. This concept has recently been expanded to blast complete stopes in one shot. This reduces the stope cycle time considerably and allows the mine to bring ore forward. Current plans for 2004 are to excavate 50% of mine wide stope production using electronic initiation technology.

Jan 1, 2004

By R. E. Murray

"It is a gloomy moment in the history of our country. Not in the lifetime of most men has there been so much grave and deep apprehension; never has the future seemed so incalculable as at this time. The domestic economic situation is in chaos. Our dollar is weak throughout the world. Prices are so high as to be utterly impossible. The political cauldron seethes and bubbles with uncertainty. Russia hangs, as usual, like a cloud, dark and silent, upon the horizon. It is a solemn moment. Of our troubles, no man can see the end." By now you, no doubt, are asking, 'Where did Murray get this bit of philosophy?' Well, I obtained it from an editorial entitled. "The Worst of Times", which was published in the Harper's Magazine in 1847. That's right, 1847! The parallelism between the situation in our country at this time and in 1847 is un- canny. But wait, there is one major exception the size of government. To my knowledge, the citizens of 1847 were not stifled by the extreme governmental excesses that we are experiencing today.

Jan 1, 1980

By R. Glenn Madill

Western Canada is defined, for the purposes of this paper, as that part of the Dominion bounded approximately by the 95th and 141st meridians of longitude and the 49th and 80th parallels of latitude. It is comprised of Manitoba, Saskatchewan, Alberta, British Columbia, Yukon, and that portion of the Northwest Territories lying to the west of the 95th. meridian. The first magnetic observations made in Western Canada were in the interests of navigation by sea. Observations were made by Captain Middleton in Hudson bay at Churchill and York Factory in 1725, and along the Pacific coast by Captain Cook in 1778 and Captain Vancouver in 1792. The first systematic magnetic survey in Western Canada was made between 1819 and 1826 by Sir John Franklin in his widely distributed explorations. It is of interest to find that while the first magnetic declination observations made in Hudson bay and along the Pacific coast were purely in the interests of navigation, the next investigations, which were made in the Western Arctic, included measurements of inclination and force with those of declination. There was a valid reason for this more complete research into the magnetic field as the construction of declination charts depended on the position of the north magnetic pole. Halley promulgated a theory 1683 that " the globe of the Earth may be regarded as one great magnet, having four magnetic poles, two of them near each pole of the equator, and that in those parts of the world which lie near any of those magnetic poles the needle is chiefly governed thereby, the nearest pole being always predominate over the more remote" . The position of a magnetic pole may be defined as a point where the inclination is 90 degrees and the horizontal force zero. It is obvious that the position cannot be' defined by declination observations alone since, for some distance from the magnetic pole, .the horizontal force is too weak to give directive force sufficient to effect the pointing of a compass.

Jan 1, 1948

By Rangaswamy. K, Naga Sivaji

A stone column is one of the most commonly employed methods of ground improvement techniques. This method used to increase the strength, decrease the compressibility of loose granular and finegrained soils. Also, it accelerates the consolidation in clays and reduces the liquefaction potential of sands and silt soils. In general, the stone column contains 15 to 75mm stone aggregates. In reality, it is not easy to avail the natural stone aggregates due to unavailability in locally nearby places. Present work aims to replace the stones partially or entirely by scrap tyre chips as an alternative material. The utilisation of recycled tyre chips in ground improvement is an environmentally friendly solution and avoid the disposal of tyre chip waste in large pits. Model tests conducted on marine clay with encased end bearing stone columns (ESC) constructed with a mixture of stone aggregate and tyre chips with sizes 4.75 to 10mm. The column diameter is 75 mm, L/d ratio maintained to 5.3. Non-woven geotextile wrapped encased stone column has introduced in the soft marine clay model. Encasement prevents the lateral squeezing of aggregates into the surrounding clay and protects the drainage function of the stone column. A set of load-settlement tests were conducted on both the clay model and clay model treated with the stones-tyre chips column. The model was loaded by the tri-axial loading frame. Shear strength parameters of stones and tyre chips were determined by large size direct shear tests. Model test results are concluding that the load-carrying capacity of the clay is improved significantly after installing the stone column in it. The encasement increases the load-carrying capacity and stiffness of the ordinary stone column. It is also proved that the stone aggregate could be replaced partially by tyre chips up to 60% without a significant reduction in its performance.

Nov 1, 2022

By Claudia Castillo, Katja Freitag, Jan Cilliers, Diana Drinkwater, Robert Seitz

The talent gap in mining is not a new challenge. Mining companies continue to seek innovative ways to attract, develop and retain talent, and younger workers are looking for opportunities to develop their professional careers. Training provides a key value proposition for both employees and employers as it helps build a talent pipeline while offering opportunities for learning and growth and value creation. In 2020, Metcelerate launched its 20-month program for early career mineral processing engineers. The program helps develop critical technical skills in the workplace and is a tool to identify motivated engineers and change culture within teams. Learners cap their skills development by executing a technical investigation. This generates immediate value—a win-win outcome for learner and company.

Feb 1, 2025

By E. Watkins, V. Gangrade

Large-opening stone mines often rely on natural ventilation and a network of auxiliary fans to produce adequate ventilation conditions in the mine instead of main mine fans, which are commonly utilized in coal mines. Large air volumes in underground stone mines, poor ventilation practices, and low operating budgets for mine ventilation potentially increase mine workers’ risk for dust, silica, and diesel particulate matter (DPM) emissions exposure. To help improve mine ventilation practices, the optimal auxiliary fan location for maximum airflow production from a ventilated intersection was determined using a combination of field measurements and computational fluid dynamics (CFD) modeling. In this study, conducted by researchers at the National Institute for Occupational Safety and Health (NIOSH), airflow quantity and fan data were collected at a partner mine to be applied as CFD model input parameters and comparison data for model validation. A six-foot diameter auxiliary propeller fan was introduced into the validated CFD model at three locations at a mine entry intersection with established ventilation flow perpendicular to the fan direction. Placing the fan on the opposite side of the intersection from the target active face area produced the highest ventilation flow rates at the downstream locations tested and produced the lowest amount of air re-circulation. The findings show that optimizing the placement of an auxiliary fan may increase the net effective ventilation flow rate by 70,000 cfm and reduce recirculation by 26%, which maximizes the potential effectiveness of large-opening stone mine ventilation systems and decreases mine worker exposures to airborne contaminants.

Mar 2, 2022

By Boo Hyun Nam, Berk Turkel, Luis G. Arboleda-Monsalve, Jorge E. Orozco-Herrera

Construction of buildings, roads, and traffic activities generate vibrations to urban infrastructure. The vibrations produced by construction activities have an impact on the soil through which they are transmitted. These effects become much more significant in granular soils. The soil conditions in Florida consist mainly of sandy soil deposits and this makes driven piles a commonly used method. In the design of deep foundation installations, it is significant to consider the potential construction issues related to the driving process. This process generates vibrations in the surrounding soils and thus, its effects on nearby soils and structures must be considered. This paper presents a web-based survey conducted among geotechnical engineers in Florida to better understand the common practice and experience regarding the effects of pile driving on surrounding soils and structures. The perception of different practitioners in the state of Florida on ground deformations and damages to adjacent structures induced by deep foundation installations are investigated. The engineers who have experienced ground vibrations and deformations were asked to define the susceptible soil conditions and main triggering factors of large ground deformations induced by pile driving. Sandy soils with loose to medium relative densities were found to be the most susceptible soil condition to generate ground deformations. Conclusions are drawn regarding the importance of considering ground vibration monitoring during the design phase of deep foundations.

Oct 1, 2022

By Leandro Rocha Lemos, Guilherme Liziero Ruggio da Silva, Iara Patricia Vieira de Oliveira, Paulo Santos Assis, Lorena Cristina Amorim Moura

O coque fica exposto a diferentes solicitações mecânicas do tipo impacto, abrasão e compressão, desde o desenfornamento até o seu consumo no Alto-Forno. Para evitar que o coque sofra uma acentuada degradação, é exigido que o mesmo apresente uma elevada resistência mecânica a frio. Para monitorar tal parâmetro, utiliza-se principalmente o teste de tambor, porém este contempla apenas a degradação por impacto e abrasão. Neste contexto, este trabalho desenvolveu uma metodologia para avaliar a resistência mecânica à compressão, inicialmente em partículas individuais de coque, apontando quais seriam as granulometrias mais resistentes. Os coques foram transformados em corpos de provas e testados em máquina de ensaio universal. Os resultados apontam que a tensão média de ruptura cresce com o aumento da granulometria. Posteriormente, foi avaliado a resistência mecânica à compressão em leito de coque, onde foi possível simular em uma prensa hidráulica, a pressão que a coluna das cargas exerce sobre o leito de coque no Alto-Forno e, posteriormente, correlacionou a compressão com o teste de tambor e se obteve excelentes resultados.

Oct 1, 2019

By K E. Mudzanani, T A. M Msagati, D T. Maiga, T T. Phadi, M R. Letsoal, B M. Chabalala, S W. Limani

This paper addresses critical environmental, health, regulatory and scientific concerns related to gold mining activities in the specific area of Barberton, Mpumalanga, South Africa. The paper thus calls for informed decisions to be made by the authorities to safeguard both the environment and people’s health. The novelty of this study is based on its comprehensive nature of the simultaneous assessment of both cyanide and potential toxic elements (PTEs) in tailings, while taking into account their composition variability over time. By combining these aspects, it is then possible to provide a holistic understanding of the contamination risks associated with mining tailings and thus justify the need for regular monitoring and supervision to ensure compliance against regulatory limits. Additionally, this paper considered investigating the dynamic nature of tailings, which are subject to changes in their chemical composition due to exposure to weathering by various agents. In this study, the determination of weak acid dissociable (WAD) and free cyanide in tailings was performed using a validated method employing the South African Council for Mineral Technology (MINTEK) Laboratory Cynoprobe. The PTEs in tailings were determined by an inductively coupled plasma optical emission spectrometer (ICP-OES). The results revealed that the tailings contained primarily substantial amounts of PTEs, including Fe (87 566 to 37 800 mg/L), Cu (271 to 110 mg/L), Mn (2100 to 680 mg/L), Ni (400 to 390 mg/L), Zn (180 to 68 mg/L), Cr (645 to 510 mg/L), As (450 to 128 mg/L), and Pb (up to 35 mg/L). The cyanide concentrations in tailings varied between 0.20 mg/L and 0.26 mg/L for free CN (with a mean of 0.23 mg/L in water leaching), 0.23 mg/L to 0.28 mg/L for free CN (with a mean of 0.25 mg/L in alkali leaching), 0.24 mg/L to 0.35 mg/L for WAD CN (with a mean of 0.28 mg/L in water leaching), and 0.31 mg/L to 0.39 mg/L for WAD CN (with a mean of 0.35 mg/L in alkali leaching). The measured concentration of cyanide and the PTEs was compared to the minimum permissible levels enforced by the South African Department of Water and Sanitation (DWS) and the Water Research Commission (WRC) regulations that govern the disposal of hazardous constituents into the environment. Additionally, it was observed that the concentrations of contaminants in the tailings exceeded the acceptable minimum limits for hazardous waste exposure, posing risks to the environment and human health.

Apr 16, 2024

By Carlos Henrique Silveira Aguiar

O tubo formador de espiras é uma guia que está localizada no Laying Head, especificado de acordo com a norma ASTM 335P22, e tem por função conformar o fio-máquina na forma de espiras sobre o transportador Stelmor. O Laying Head gira continuamente, durante a operação normal, sendo que a cada revolução do tubo, uma espira é produzida, cujo diâmetro é determinado pelo raio final do tubo e pela velocidade do Laying Head, em relação à velocidade do Laminador. Estes tubos, durante a laminação dos aços BEXX, sofrem um desgaste acentuado, que é provocado pela carepa formada durante a passagem do fio máquina pelas caixas d’água, durante o processo de resfriamento. Desta forma, torna-se necessário trocá-los a cada 200t laminadas do referido aço, com tempo estimado de 30 minutos de parada. Além disso, há um desgaste físico acentuado na atividade de troca dos tubos, que coloca em risco a segurança dos funcionários. Outro efeito indesejável relaciona-se com o risco de ocorrência de sucata de linha, provocada pelo rasgamento do tubo, quando são fornecidos tubos cuja composição química se apresenta no limite inferior de especificação. Há programa de laminação que exige até 6 trocas diárias de tubo. Com a proposta de se incrementar a tonelagem laminada por canal dos discos de laminação do Bloco No Twist, tornou-se necessário desenvolver um tubo com insertos de metal duro, com vistas a aumentar a vida útil dos mesmos, como também a produtividade do Laminador 2.

Jul 30, 2018

By Sven Schröer, Lilma Schimmel, Dimiter Alexiew

"The Geotextile Encased Columns (GEC) deep foundation system for embankments on soft soils was introduced some 20 years ago and is now considered State-of-the-art worldwide.The GECs consist of compacted granular fill, similar to common gravel columns, with one decisive difference: they are confined in a high-strength low-strain flexible geotextile “cylinder” (encasement). This engineered element provides a very efficient tool to control and optimize the behavior of the system. GECs perform very well even in extremely soft soils ensuring bearing capacity (stability) and reducing settlements. Due to the encasement, they a lso provide high lateral ductility. A wide range of fills including sands can be used.The remarkable reduction of vertical stresses in the soft soil surrounding the GECs results in a decrease of lateral pressure as well. Such reduction combined with the lateral ductility allow GECs to be also used for lateral pressure-relief adjacent to sensitive foundations, e.g. rigid piles. The application of GECs as lateral pressure relief was recently used in Brazil and Germany where bridge abutments were built on concrete reinforced-piles. The GECs below the bridge approaches and adjacent to the piles decreased the lateral pressure to acceptable values.This paper presents two case studies for which the most relevant parameters, the geotechnical conditions, specific problems, engineering philosophy, final solution and lessons learned are discussed. Furthermore, instrumentation programs were applied in both projects. The most important results in terms of displacements and stresses are shown, evaluated, summarized and commented upon, focusing on the lateral stress-relief, followed by conclusions and recommendations."

Jan 1, 2016

By Racquel Nottingham, Marc Mastrantuono, Freddy Lopez

In the digital era that we live in, connectivity and mobility play a decisive role in our daily activities. In this context, insufficient telecommunication infrastructure gives origin to the so called “dead zones” (areas with poor or non-existing cell phone reception), which hinder economic development in small communities and in many rural areas, since they remain invisible to a larger marketplace due to the inadequate cellular coverage. Several countries are working to identify these dead zones and with this information, establish strategies together with mobile providers in order to improve the existing mobile networks by expanding the coverage areas. As a result of the analysis, it is expected that thousands of telecommunication towers for 4G and 5G networks will be erected in the coming years. Telecommunication towers are slender elements that require large shallow foundations to verify primarily the safety against overturning. However in remote areas, it can be advisable to consider alternatives to the conventional shallow foundations, in order to optimize the use of materials (concrete, reinforcement steel, etc.). The following article presents an overview of intervention projects, where telecommunication towers were founded on micropiles. The micropiled foundations allowed to reduce considerably the dimensions of the originally planned shallow foundations. Furthermore, the use of micropiles allows for additional optimization, in combination with pre-fabricated foundations (i.e., precast concrete elements, etc.). This paper will focus mainly on the design and the execution of the micropiled foundation.

Sep 8, 2021

By D Xu

BHP Billiton Iron Ore is one of the world’s premier suppliers of iron ore. It currently has operations in Western Australia and Brazil and also has some iron ore interests in West Africa.BHP Billiton’s Optimisation R&D team has developed a proprietary mine planning optimisation tool that uses a mixed integer linear programming (MILP). This tool is called Blasor and it is used to rapidly evaluate the resource development potential (RDP) scenarios for the company’s business development strategy. In addition it generates life of asset (LOA) mine plans for the company’s operations and growth projects. The Blasor optimiser maximises the discounted operating cash fl ow (DCF) as the objective function, subject to mining, processing and transportation capacity constraints and blended product quality constraints. The paper will outline how Blasor has been applied to the resource development potential (RDP) strategy scenario studies, growth project evaluations and LOA mine planning within BHP Billiton Iron Ore.The practical application of Blasor to resource planning optimisation within BHP Billiton Iron Ore has demonstrated the value of such a tool for optimising strategic directions through the evaluation of a number of carefully proposed scenarios and maximisation of operational decisions, such as cut-off grade, open pit development sequence, etc. Particularly for the company’s business development direction studies, Blasor plays the role of a fair valuation tool in that it discovers the most valuable resource development scenario, thus establishing a sound basis for comparing the economic merits of each scenario.

Jul 11, 2011

By K. Cole, D. Mesa, P. Brito-Parada, M. R. van Heerden

Turbulence in mechanical flotation cells, achieved via an impeller, plays a key role in keeping particles in suspension, dispersing air bubbles, and promoting particle-bubble collision. However, studying the hydrodynamics of a flotation cell is not a simple task, due to the complex nature of flotation systems which are opaque, turbulent, multiphase and polydisperse in terms of particle and bubble sizes. In this paper we study the impact of impeller design modifications on the hydrodynamics of a continuously overflowing bench-scale flotation tank. To this end, two different impeller designs, with and without a stator, were assessed using Positron Emission Particle Tracking (PEPT). This allowed the authors to determine, for the first time, the effect of an impeller design on the behaviour of both hydrophobic and hydrophilic particle tracers. It was experimentally observed that the use of a stator modifies the hydrodynamics within the flotation cell, distorting the lower mixing loop that is characteristic of axial impellers. The role of the stator in dissipating turbulence results in reduced particle velocities outside of the impeller-stator region. These results have important implications for flotation cell design and are discussed in the context of the impact that different designs have on particle movement, flotation hydrodynamics and, ultimately, flotation performance. The data set generated is also extremely valuable for modelling and validation purposes. Keywords: Flotation, flotation tank, impeller design, rotor, stator, PEPT, hydrodynamics

Jan 1, 2020

By M. Rudolph, A. D. Renno, H. Wu

In this study, synthetic pure cassiterite and cassiterite doped with Fe were successfully produced by sintering. Their crystal structure and chemical compositions are characterised by optical microscopy, X-ray powder diffraction (XRD) as well as scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDS) based chemical composition analysis. The electrostatic behaviour of synthetic and natural cassiterite was studied by electrophoretic measurements. Their floatability was studied by microflotation with two types of anionic collectors. Results show that the cassiterite floatability with these collectors behaves differently and lead to two opposite results: Natural cassiterite (enriched with Fe) > undoped pure SnO2 by using sulfosuccinamate (Aerosol® 22) Undoped pure SnO2 > Fe3+ doped > natural cassiterite (enriched with Fe) by using styrene phosphonic acid (SPA). Keywords: Synthetic cassiterite, lattice impurities, flotation, zeta potential, Aerosol® 22, styrene phosphonic acid

Jan 1, 2020

By M. Shahsavar, J. Sattarvand, J. Gomez

Mining can be categorized as a hazardous activity, considering some factors such as environmental conditions with a considerable presence of humidity, suspended particles, or falling rocks have affected the severity and number of accidents compared with other economic sectors. The industry analyzes incident reports to narrow the rate of severe injuries and fatalities, conducting root cause analysis and identifying leading indicators. As the International Council on Mining and Metals noted, the vast trove of incident data is not analyzed as much as possible due to a lack of analytics expertise at mine sites. However, machine learning could solve the problem of analyzing all the incident data in a no-timeconsuming way, considering the abundant data, and without using expert personnel in data science. Thus, a Convolutional Neural Network and a Naïve Bayes model were introduced to perform classification in the MSHA database. The database from 2020 consists of 60 fields to describe safety incidents; these fields include mine I.D., accident date, subunit (mill, surface), material extracted, and other metadata.

Jun 25, 2023

By O. T. Konina, V. A. Masloboev, A. V. Svetlov, E. A. Krasavtseva, D. V. Makarov, A. A. Goryachev

Dusting phenomena have been examined at the tailings storage facility of Apatit JSC Kirovsk, a mining operation located in the far north of the Russian Federation. The material composition of the tailings was identified. Existing dust suppression methods were examined. Field observations were undertaken and official data was obtained from the Murmansk Administration for Hydrometeorology and Environmental Monitoring, and analysed. A database was built for forecasting dusting according to critical scenarios in order to estimate the peak MPCs of suspended solids in the atmospheric air. Mitigation measures were formulated and recommended to the mining operation. Keywords: Mineral dust particles, apatite-nepheline ore concentration tailings, suspended solids MPC, climate change

Jan 1, 2020

By D. Hu, J. Xu, N. Liao, C. Wu, J. Ye

The vertical stirring mill’s fine grinding equipment is affected by the operating conditions during the grinding process. The grinding media has a great influence on the energy consumption and particle size distribution. This paper investigates the fine grinding performance of nano-ceramic balls and steel balls of the same weight for magnetite by a wet grinding process in a vertical stirring mill, where 15 mm nano-ceramic balls and 12 mm steel balls are used as grinding media to carry out batch grinding tests. We have observed that the newly qualified particle content of the nano-ceramic balls is higher than steel balls of the same weight at the same specific energy. The reason may be the advantage of a greater surface area and volume filling rate with the nano-ceramic balls. Moreover, the specific energy of nanoceramic balls is less than steel balls of the same weight under the same grinding fineness. In addition, energy efficiency indicates that the nano-ceramic ball has a higher energy efficiency than a steel ball of the same weight. This is due to the light bulk density of nano-ceramic balls. The application of a nanoceramic ball in a vertical stirring mill will improve iron ore grinding performance. Keywords: Steel balls, nano-ceramic balls, vertical stirring mills, fine grinding, particle size distribution, energy consumption

Jan 1, 2020

By Kátia Cristina Gouveia

O objetivo deste trabalho foi determinar a TTDF do aço ASTM A36 com diferentes graus de encruamento após ensaios de impacto Charpy, sob diversas metodologias. Não se notaram diferenças no comportamento do material quando se avaliam os valores de TTDF obtidos pela medição da expansão lateral dos corpos de prova, nem considerando o valor da TTDF na qual o material apresenta 50% de fratura frágil, usando as metodologias de avaliação visual das faces de fratura dos corpos de prova, embora os valores sejam divergentes dos valores obtidos pelos métodos analíticos. A avaliação das faces de fratura dos corpos de prova por microscopia eletrônica de varredura permitiu visualizar que nas regiões onde visualmente considerou-se que havia apenas fratura frágil, também haviam regiões típicas de fratura dúctil. Conclui-se que a metodologia mais indicada é aquela que considera a TTDF como a temperatura na qual a energia absorvida é a média dos patamares superior e inferior, pois é um método simples, de fácil reprodutibilidade e que melhor refletiu a tendência de comportamento do material nos diferentes graus de encruamento estudados.

Aug 7, 2018