Search Documents

By F. C. Lendrum

Introduction The property of Normetal Mining Corporation is in Desmeloizes township, Quebec, twelve miles north of Dupuy on the main line of the Canadian National railway from Quebec city co Cochrane, Ontario. The ore bodies occur within a band of highly sheared and sericitized agglomerate which strikes N.60°W. and clips 82° north. Along a zone 1,000 feet or more in length and of variable width, the agglomerate has been replaced by copper, zinc, and iron sulphides, with copper usually predominant on the hanging-wall side and pyrite replaced in part by sphalerite on the footwall. A northsouth diabase dyke cuts through the ore zone near its east end. The Normetal mill produces a copper concentrate and a zinc concentrate which are shipped, respectively, to Noranda, Que., and Newcastle, Penn., U.S.A., for further treatment. The present paper deals with the milling of ore from what is known as No. 3 orebody. This is a lenticular body of high-zinc ore lying co the east of the diabase dyke, along the line of strike of the main ore zone, which extends westward from the dyke. On its northern side, No. 3 orebody is in contact along most of its length with a narrow band of copper ore which is highly oxidized.

Jan 1, 1948

The role of a project metallurgist is diverse and covers input into the resource definition, mining studies, metallurgical test program development, process engineering and plant design, cost estimate preparation and financial analysis aspects of project feasibility studies. Mining project schedule and cost overruns can often be attributed to cutting short metallurgical test work, engineering and cost estimating leading up to commitment to development. In a significant number of cases this may result from the lack of understanding and commitment by the project proponent to the requisite metallurgical and processing studies required during the various pre-commitment stages of a mining project. Metallurgical test work, process development, engineering and cost estimating requirements for each stage of pre-commitment development are described together with a summary of the ongoing role of the project metallurgist during detailed engineering and commissioning of a process plant.

Jan 1, 2008

By L. F. Heising

Ten composite samples of Mesabi Range nonmagnetic taconite from the Hibbing, Minn., area were evaluated by flotation and by reduction roasting-magnetic separation to determine their potential as a future source of iron are. Only one of the composites yielded concentrates that could be considered marketable, using as a criterion a 10-to-1 iron-to-silica ratio. Cursory petrographic examinations of all 10 composited samples and a detailed mineralogical study on 1 sample suggest that unfavorable mineralogical associations between iron and gangue minerals are responsible for their poor beneficiation characteristics.

Jan 1, 1967

By Chas. E. van Baraeveld

"The information presented in this report is a by-product of studies concerning zinc, and is published in response to various inquiries for information as to the suitability of zinc for roofing. It parallels a previous report of the Bureau of Mines on slate roofing.Available Forms of Zinc RoofingZinc is available for roofing in three forms: 1. As sheet zinc which may be used advantageously on roofs with as flat a pitch as 1 in 4; laid with standing seam construction for small roofs and with batten construction for large roofs. 2. As corrugate sheets, in widths up to 40 inches and in lengths up to 8 and feet, available for siding and roofing in industrial buildings (with certain re¬strict ions) and or farm buildings (without restrictions). 3. In the form of shingles.Advantages of Zinc Roofing1. Zinc is a permeant roofing material; that is, when suited to the conditions, and properly applied to a roof designed with the right purlin spacing it will outlast the building and still have a salvage value equal to a least half the original material cost. It is applicable to a wide range of conditions, from the most expensive to the cheapest type of construction, and is not greatly above the cheaper materials in first cost. A permanent roof of simple outline need not cost over $15 to $25 per square (100 square feet), depending upon the method of construction required a corrugated sheet roof for industrial purposes or for farm use need not cost over $15 per square for ordinary conditions. 3. Corrugated zinc sheets have the distinct advantage of being available for re-use and re-construction if handled with ordinary care. 4. Zinc oxidizes to a certain point, building up a strong protective coating which in time effectually checks further oxidation; thus it does not oxidize to the point of destruction as steel does, 5. It is light and easily handled."

Nov 1, 1924

By H. O. Seigel, J. C. Gingerich, E. O. Köstlin

"To satisfy their continuing need to replenish or expand their ore reserves, mining companies are faced with the dilemma of arriving at a proper balance between the dual avenues of discovery through in-house exploration and of acquisition of properties that are relatively proven or are even in production. The returns from exploration activities may be spectacular, but are unpredictable. The allure of an acquisition lies in its promise of quick and risk-reduced addition to reserves. However, it is historically clear that quantum increments in shareholders’ values have arisen primarily through major exploration discoveries, rather than through major late-stage acquisitions. Late-stage acquisitions can prove highly profitable, sometimes based upon the planned use of superior mining or metallurgical technology, but more often occur as the result of unexpected windfalls. At the other extreme, they can become expensive failures through inadequate due diligence, or unforeseeable factors.Citing numerous case histories and industry statistics, it is concluded that a judicious combination of both exploration activity and the acquisition of prospects is the most advantageous strategy for adding new ore reserves. A skilled exploration staff is essential for success, be it through exploration discoveries or through opportunistic acquisitions, preferably at their early stages. In the future, it is anticipated that there will be fewer opportunities for acquisition because of reduced funding for junior exploration companies, leading to increased competition and higher costs for fewer properties, both in the advanced exploration and mining stages."

Jan 1, 2002

By J. B. Gayle

Since the turn of this century, there has been increasing interest in the application of flotation processes to the beneficiation of finely divided minerals of various types, This is reflected by the large numbers of papers dealing with various aspects of this problem published annually both in this country and abroad. For the most part, such papers fall into one of three categories: 1. Those concerned with achieving, by various chemical and/or physical means, a set of conditions under which certain particles become potentially floatable while others do not. 2. Descriptive studies of plants and pilot plants effecting separations between such particles. 3. Studies of the effects of certain design and operating variables on the rates and efficiencies with which such separations can be effected.

Jan 1, 1959

By C. A. Herbert

During the fiscal year ended September 30, 1932, there were 27 fatalities in the coal mines of Indiana. Four of this number occurred in small mines employing less than 10 men, over which the State Inspection Department has no jurisdiction. In addition to these coal mine fatalities, an explosives accident in a clay mine resulted fatally to one man. Tables 1 and 2, which follow, list the fatalities as to cause and occupation. Table 1. - Fatal accidents by cause, fiscal year ended September 30, 1932 [ ]

Jan 1, 1933

By R. Feenstra

In the course of time, an increasing number of investigations on jet cutting all kinds of material, such as rocks1, 2, 3, metals4, 5, and wood6 have been reported to serve various applications. This paper deals with one particular application of jets, viz deep-well drilling for hydrocarbon exploration and production. A number of papers have been published on this subject 7, 8, 9, some of which refer to jets purposely containing abrasives, termed 'jetted particle drilling'7. Since such abrasives complicate fluid handling considerably and do not appear to be absolutely necessary for making hole we have restricted ourselves to conventional drilling fluids. A large part of our investigation has been performed with the aid of three laboratory-type drilling machines, which permit tests on both micro-bits (12 in) and full-scale bits (62 - 9 5/8 in). In view of the application of jets in deep wells, care has been taken to simulate hydrostatic pressures as they exist in the field on the hole bottom. These have been found to have a major effect on the bit-penetration rate for various drilling fluids. Following experiments with single nozzles, laboratory bits have been designed, improved further and developed for field use. Field runs on 9 5/8 in bits, using conventional equipment and pumps, served to verify the feasibility of the jet drilling concept. Further efforts are evidently needed to evaluate the jet drilling method. It is encouraging that one of these10, a field test programme, is supported by a number of oil companies jointly. Such a combined effort is of paramount importance to evaluate and develop this new method of drilling to its full potential in a reasonable period of time. This paper aims to contribute to that ultimate goal.

Jan 1, 1974

By D. P. Roberts

This investigation aimed to simulate the experiments performed by Nic Gay (Gay, N.C.1976. Fracture growth around openings in large blocks of rock subjected to uniaxial and biaxial compression. International journal of Rock Mechanics and Minining Sciences and Geomechical Abstracts, vol. 13. pp. 231-243) on fracture growth around openings in blocks of rock subjected to uniaxial and biaxial compression, using the Elfen discrete element code. The results of the physical experiments indicated a number of trends that were successfully replicated in the numerical simulations, including crushing ahead of the face, the formation of a sub-vertical tensile fracture at centre-span, the formation of groups of fractures originating from the crushed face zone, the formation of large corner-to-corner fractures which precede sample failure, and linking of slot corner and sample corner fractures leading to sample failure. In addition, other features were apparent that were not reported by Gay. It is believed that these took the form of conjugate shear fractures (as reported by Gay in a previous paper) and other features that may have been altered or inhibited by the presence of pre-existing structure in the physical samples. It was found that the samples, though nominally made up of the same rock type, must have had significantly differing properties. The presence of pre-existing structures may have contributed to this discrepancy. Strain measurements from the physical experiments were reasonably well matched, except where the gauge lay directly in the path of advancing fractures.

Jan 1, 2012

By D Giurco

As part of global systems of mineral production and consumption, the Australian minerals sector is facing sustainability challenges across technological, social, ecological, economic and governance domains, as well as between local, national and global scales. To ensure that the Australian minerals sector progresses towards sustainability, it is imperative to understand the possible ways in which AustraliaÆs mineral resources could support sustainable futures. A significant research gap exists between the complex nature of questions concerning minerals sustainability and the reductionist methods available to deal with them. This paper argues the need for broader, more integrated approaches to questions concerning minerals sustainability, which can address multiple human perspectives, complex and æmessyÆ patterns and processes across multiple organisational, temporal and geographical scales and whole systems of mineral production and consumption. To inform the development of a new approach to minerals sustainability, this work reviews the contemporary understanding of the Australian minerals sustainability problematic, from the perspective of the Australian minerals sector (Minerals Council of Australia), the Australian research sector (Mudd 2007a, 2007b; Mudd and Ward 2008) and a multi-scale international project (MMSD 2002). This review shows the focus of current responses to the minerals sustainability problematic, identifies the need for an integrated approach to questions of minerals sustainability and addresses how different approaches are informed by underlying and unarticulated assumptions about the tolerability of tradeoffs between different societal goals, the treatment of uncertainty and the application of different conceptual geographical, organisational, temporal and life cycle scales to define the minerals sustainability problematic. The Mineral Resources Landscape proposed, offers an expanded conceptualisation of minerals sustainability, to link minerals production and consumption in an integrated assessment across the entire minerals supply chain, connecting social, ecological, technological, economic and governance domains across local, national and global scales. The key leverage points governing change in the Mineral Resources Landscape are identified as: the material source, extraction and production technologies, level of service and value, and consumption patterns. Mapping the key challenges facing the minerals sector, as identified in the review herein, indicates that the boundaries defining traditional conceptualisations of minerals sustainability focus on the material source and technology and ignore two very key drivers of the Mineral Resources Landscape û the æservicesÆ minerals offer to society and the æconsumption trendsÆ which assimilate these services into society. Understanding these overlooked aspects of the Mineral Resources Landscape, along with the conventional areas of focus, is essential for identifying the Australian minerals sector as a provider of sustainable mineral services. This insight prompts a reconsideration of the role of minerals services and consumption trends, together with the role of the material source and technology in shaping change and the emergence of sustainable systems of Australian minerals production and consumption, across multiple scales and domains.

Jan 1, 2009

By Augustus Locke

Jan 1, 1923

By A. Wahab Khair, N. P. Reddy

"INTRODUCTION The continuous mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners which were designed for increased productivity have also increased the concentration of respirable dust in mines. Inhalation of this respirable dust by miners causes the Coal Worker's Pneumoconiosis (CWP). Concern for CWP increased in the United States following a 1963-65 survey that showed definite x-ray evidence of CWP in 9.8 percent of working miners and in 18.2 percent of nonworking miners in the Appalachian bituminous coal region (Breslin and Niewiadomski, 1982).One of the major objectives of the Federal Coal Mine Health and Safety Act of 1969 was the prevention of CUP. This law initially limited the daily average exposure of coal miners to 3 mg/m3 of respirable dust. However, following the results of a probabilistic model developed by Jacobsen, et. al. in 1971, the limit was reduced to a mass concentration of 2 mg/m3 unless quartz content exceeds 5 percent, a rare occurrence in mines. Based on x-ray categorization prior to death it is believed that the mass concentration in the respirable fraction is a parameter of primary interest for hygenic evaluation of dust exposure. Morgan, Burgess and Jacobson (1973) suggested that the quantity of inhaled dust, although influential is not the only aspect of exposure which is significant in producing CWP. Miners working in higher rank coal (anthracite) mines are more susceptible to CWP (Morgan, Burgess and Jacobson, 1973). This also confirms the findings of the British (Bennett, Dick and Kaplan, 1979 and Hurley, et. al., 1979) and Germany (Reisner and Rubock, 1977). Based on the cytotoxicological evidence Reisner and Rubock (1979) suggested that when coal properties are similar, increasing quartz and mineral content increases toxicity. David, Ottery and Le Roux (1975) examined that as the severity of the CWP increased the retention of the coal dust content in the pulmonary region remained the same, while that of quartz content increased significantly. Leiteritz, Baur and Bruckman (1971) studied the various components of coal dust and showed that coal particles comprised a smaller fraction of the mass of fine dust than did particles of quartz and minerals. It is ironic that quartz and mineral matter both comprise smaller fractions of the higher rank coal dust (Dodgson, et. al., 1971 and Dwiggins, 1981). Results of a recent research revealed that quartz or any other mineral examined had no strong or consistent effect on the incidence or progress of CWP (Attfield, 1984) while Dodgson, et. al., (1971) concluded that high exposures to minerals such as illite, kaolinite and mica will retard the progress of CWP. Size and shape characteristics are believed to be important in the relationship between mineral particles and health effects (Shedd, Virta and Wylie, 1982)."

Mar 1, 1989

By Paul C. Lingo

Two recent antitrust cases, coming from widely separated areas, different industries and involving wholly different facts were decided by the Supreme Court on June 7, 1965. The decisions in these two cases may well prove to be the most important and far-reaching decisions in the field of labor law that have been handed down in the last 24 years. These cases, although quite dissimilar factually, had one common element. In both, the gravamen of the antitrust violation was bottomed on the terms of labor agreements negotiated by a multiemployer group. These cases are usually referred to as Pennington1 and Jewel Teat. Since a number.-of references will be made to the antitrust laws, it may be well to state briefly the applicable portions. Section I of the Sherman Antitrust Act makes "every contract, combination in the form of trust or otherwise, or conspiracy, in restraint of trade or commerce among the several states, or with foreign nations, is declared to be illegal...". Section 2 imposes criminal sanctions against "Every person who shall monopolize, or attempt to monopolize, or combine or conspire with any other person or persons, to monopolize any part of the trade or commerce among the several states...". Under Section 4 of the Clayton Act a person who sustains damages as a result of a violation of the antitrust laws is entitled to recover treble damages plus costs.

Jan 1, 1965

By J. C. Duchon

The use of extended workdays or compressed workweeks (regular shift lengths exceeding 8 h) is attracting growing interest in many industries using continuous operations. While extended workdays promise increased worker satisfaction due to more days off, including weekends and holidays, there are legitimate concerns about the potential effects on the health and safety of such a schedule. The U.S. Bureau of Mines (USBM) conducted a study at a Canadian underground copper, lead, and zinc mining operation that was designed to study the safety and performance implications of extended workdays. Measures were taken before and after a change from the old 8-h continuous schedule to the new 12-h continuous schedule, including behavioral performance measures to analyze perceptual-motor changes, continuous heart-rate monitoring and aerobic capacity to measure physical fatigue, a variety of self-report questionnaires to measure perceived adaption and satisfaction with the new schedule, and pulmonary-respiratory measures to examine air contaminant exposure. Based upon the overall acceptance of the new schedule by the workers and lack of change in fatigue-sensitive behavioral and physiological performance measures, this study recommends that the mine retain the 12-h schedule. However, certain precautionary measures are suggested to insure the safety of the workers.

Jan 1, 2010

By O. E. Wheeler

The term "finite element analysis" is heard and seen in print a great deal these days; a few words on what precisely it is are in order. In the broadest sense, finite element analysis is an application of an idea developed by a nineteenth century mathematician named Rayleigh. His basic idea was to decompose any problem in mathematical physics into a large number of simpler problems, solve the simpler problems, and then put those solutions together to form an approximation to the solution of the original problem. The scheme works nicely because of two features: first, much of the difficulty in solving practical problems of mathematical physics stems from irregularities in the boundaries and the simpler problems can be chosen with regular boundaries and second the smaller problems are solved for small physical areas where simple approximations of the solution do not differ much from the true solution. In the narrower sense, in which we are now interested, finite element analysis is a technique of using imaginary simple structural elements to construct analytical models of real structures. A direct parallel with the Rayleigh approach exists since the "finite elements" have simple boundaries and are restricted to simple behavior within a single element. Although the correspondence between Rayleigh's ideas and finite element analysis is now widely recognized, the computational tool, as it has developed over the last thirty years, comes not from the discipline of physics but rather from that of structural engineering. It is interesting that it came not from the traditional research community, the universities, but instead from working

Jan 1, 1974

By J. B. STEWART

T HE position of each hole of any series of holes was carefully located by the surveyor, plotted in plan and elevation, and numbers assigned to them. The second series was staggered halfway between the first and so on for each succeeding series. Two and a, half to three months was frequently required to grout a series of holes calculated to insure safety for sinking a distance of 10 meters or say 33 ft. Naturally the initial operation called for drilling and grouting two series of holes but thereafter each sinking campaign required only one series of holes as shown in Fig. 8. The pump handling about 75 gal. per minute corresponds to 46 tons of grout or 6 tons cement delivered as a fair over-all average for the 24 hours. Thus 600 to 800 tons of cement was used for a single section of 33 ft. depth of shaft. One campaign used nearly 1100 tons of cement. Some holes were effectually sealed with as low as 30 tons, while many required 60, and some 80 to 90 tons.

Jan 1, 1926

By Weijie Wei, Jinwang Zhang, Shengli Yang

Due to the unbalanced top coal drawing process, the recovery ratio is low, and the equipment stability is poor in the longwall top coal caving mining (LTCC) with an inclined seam. Aimed at these problems, this paper proposes the dynamic group caving method (DGCM). The basic procedure is that when the drawn volume of top coal from a support reaches about half, the next support begins drawing top coal, and the drawing process between the two supports is half done. Taking the panel no. 8103 in Beixinyao mine as the research object, the characteristics of drawing body shape, particle movement trace, and variation of recovery ratio are investigated by using Particle Flow Code. Furthermore, the effect of mining-caving ratio on the top coal drawing law under DGCM is revealed by the simulation results, and compared with the single-opening sequence caving method (SSCM) and the doubleopenings sequence caving method, advantages of DGCM are determined in inclined seams. The results show that the drawing body can be divided into the left and the right under DGCM. Specifically, the drawn top coal particles in the left are from the upper part of this support, that in the right are from the lower part of next support, which verifies the correctness of the theoretical analysis. The characteristics of the drawing body shape are more significant when the mining-caving ratio is relatively small. In addition, with increasing mining-caving ratio, the recovery ratio of the panel both increases gradually underDGCMand SSCM.When the miningcaving ratio is less than 1:1, the recovery ratio of DGCM is obviously higher than that of SSCM, indicating that DGCM can greatly improve the recovery ratio. While when the mining-caving ratio is larger than 1:1, the recovery ratio of two caving methods is basically equal; however, the advancing time is significantly shortened under DGCM. This study are of great significance to realize high efficiency and precise caving in LTCC with an inclined seam.

Jul 7, 2020

By Frank Ruskey

Many problem associated with potential hazards in a proposed mining area may not be adequately appraised because of the complexity of trying to evaluate them in terms of production requirements. Frequently, encountered hazards have to be dealt with by day-to-day operational schemes that require the miner to either force a way through them or avoid them by blocking off the area in which the hazards are known to exist. These considerations, after the mine is in full production, can be costly to the mine operator and can increase the danger to the miners. A hazard-evasion computer program for mine planning that will appraise proposed mine layouts on the basis of existing or potential hazards has therefore been developed. The program is intended for use during the planning phase of a mine, where it should assist the mining engineer in making decisions in mine design. With the output from this program, the mining engineer should be able either to corroborate his judgments made on the basis of mining experience or to find unanticipated solutions to design problem. The program tests hundreds of possible solutions to a mining layout, and by sorting out the 10 best (based on a criteria of minimum-abandoned-coal) limits the number of choices that need to be considered and appraised for applicability to a given mine scheme.

Jan 1, 1973

By C. Musingwini, A. S. Nhleko, P. M. Muke

Open-pit mine planning includes the determination of a long-term open-pit mine production scheduling (OMPS) plan. The OMPS plan is generally a three-dimensional (3D) block extraction sequence that seeks to maximise the net present value (NPV) of future cash flows, while complying with technical and operational constraints. The OMPS problem is computationally complex because it involves the analysis of large datasets, while simultaneously incorporating both multiple hard and soft constraints. The OMPS problem has been solved using deterministic or exact approaches, heuristic, and metaheuristic models. When compared to heuristic and metaheuristic models, deterministic approaches tend to take much longer to solve the OMPS problem when the number of constraints increases. Therefore, this paper presents a metaheuristic model which utilises a genetic algorithm (GA) framework to solve the OMPS problem. The GA-based model was applied to the Newman1 and Zuck Small mining instances, which are publicly available from the online MineLib database. The NPVs for the OMPS plan generated using the GA-based model for the two case studies were compared to the best-known published MineLib solutions obtained using the TopoSort heuristic model at the time of this study. For the Newman1 instance the equivalent annual NPVs were approximately US$6.6 million for the GA-based solution and US$5.1 million for the TopoSort solution. For the Zuck Small mining instance, the equivalent annual NPVs were approximately US$99.8 million for the GA-based solution and US$102.5 mil for the TopoSort solution. These results show that the GA-based model produced comparable solutions to some of the best-known solutions, thus, indicating strong potential application of GA-based models to solve OMPS problems.

Sep 1, 2021

By James Douglas

A century ago the AIME meeting of 1899 was held at the Palace Hotel in San Francisco California in September. For his presidential address, James Douglas presented this paper which is reprinted in full with the kind permission of the AIME. It presents an interesting comparison relating to events and circumstances in the metallurgical industries at the close of last century. Being on the eve of a new century ourselves, the Editors of this volume of the COPPER 99-COBRE 99 Proceedings considered this paper would be of general interest, hence it is included here. Douglas believed in effective interchange of technical experiences and ideas. He considered the extreme secrecy surrounding the copper works at Swansea, Wales, the world center of copper only years before the time his paper was delivered, as one key reason for its decline, (and eventual closure of all copper plants there). In his paper, the pace of developments in various sectors such as transportation (railroads, the dominant means of I transportation at the time), the iron and steel and copper industries were examined, in much the same way as one might do but on the high technology of today. James Douglas was born in Quebec City, Quebec, Canada and spent his early life there. Forced to move to the United States for family and financial reasons, he went on to become a pioneer in the new Arizona copper industry, and with luck and good judgement with his interest in the new mining properties he also became very wealthy. Douglas was an accomplished mining and metallurgical engineer. He was the first President of Phelps Dodge and helped transform the small trading company of Anson Phelps and William Dodge into a mining giant.

Jan 1, 1999