Search Documents

By Jafar Safarian, Merete Tangstad, Leiv Kolbeinsen

"Silicon and its binary alloys have several applications in metallurgical, chemical, photovoltaic and semiconductor industries. Silicon goes to its liquid state within its production, refining and when it is alloyed with other elements. Therefore, the characterization of silicon melts thermodynamics is important and useful. The liquidus and activities in several silicon binary systems have been recently calculated by the application of two liquidus constants, which were established using the experimentally determined liquidus data. In the present study, the thermodynamic properties of six silicon binary melts, which are simple eutectics, are calculated by analytical approaches. In this case, the changes in the partial and integral Gibbs free energies and enthalpies of mixing are calculated and compared with the experimental data in literature. The enthalpies are calculated by two methods and the calculation results are compared to the data from the literature. It is shown that thermodynamic properties of silicon binary melts can be accurately predicted without the use of complicated thermodynamic software.IntroductionSilicon and its alloys have several industrial applications. Silicon is used for making aluminium-silicon alloys to produce cast parts, mainly for automotive industry. Silicon in the form of ferro-silicon is used to deoxidize and alloy steel and cast iron. The photovoltaic (PV) industry has had a rapid growth in the recent years and silicon is the dominant material used for the fabrication of solar cells. Silicon is primarily produced through carbothermic reduction of quartz in electric arc furnaces and the produced metallurgical grade silicon (MG-Si) contains around 1 wt% impurities. It is further refined to produce solar grade silicon (SoG-Si) with above 99.9999 wt% Si to fulfil the chemical requirement for PV application. Since molten silicon is processed all along the metallurgical route, obtaining fundamental thermodynamics knowledge about silicon melts is valuable for the related industries."

Jan 1, 2012

By C Artica

Two quantitative methods for Mineral Resource classification have been applied to a copper skarn deposit beneath a large open pit that is mining a world-class porphyry complex. A drill hole spacing study (DHSS) using the single block kriging method (SBK) and a conditional simulation method (CS) were applied to the skarn deposit and the results compared. Inputs to both processes included the proposed mining rate and stope designs to estimate the likelihood of achieving grade and metal production targets. Mineral Resource classification of the deposit considers the relative precision of tons, grade and metal predictions over quarterly and annual production periods. These relative precision estimates are calculated at 90 per cent confidence interval (CI). The SBK method represented the production period as a single large block. Kriging estimates were performed in the large block for various synthetic drill hole grids, and the estimation errors derived. The error was assumed to be normally distributed due to the large block size and quantity of samples, allowing CIs to be deduced. The CS method followed a conventional sequential Gaussian simulation workflow where grades were simulated with a 5 ft × 5 ft × 5 ft grid node spacing inside mineralisation domains. Each realisation was then averaged up to monthly production volumes represented by a combination of designed stopes, and the coefficient of variation (CV) for the averaged grade was calculated. CI on the relative precision of grade predictions were then deduced from the CVs. The two methods produced similar results; despite being calculated independently. CS results were used to report uncertainty in the proposed life-of-mine plan and highlight areas for additional drilling. SBK results were used as the basis for Mineral Resource classification as this method has been previously applied to the skarn deposit.

May 24, 2023

By Fengming Li, Baocheng Song, Yuemin Zhao, Hailin Dong, Liping Peng, Chusheng Liu, Chenlong Duan

The large-scale vibrating screens with high processing capacity and efficiency are now in great demand in the mineral processing industry of China. However, as the equipment is always suffering from the strong external harmonic exciting force, the inertial force and the impact from the minerals, the fracture of the beam and the crack of the lateral plate are easy to occur, which has a negative effect on the reliability of the equipment itself and the industrial production. Considering the essential high reliability of the equipment, a new large-scale vibrating screen with duplex statically indeterminate mesh beam structure (VSDSIMBS) was developed. The natural characteristics, namely, the natural frequency (or the modal frequencies) and the natural mode, and the dynamic characteristics of the VSDSIMBS were obtained by the modal analysis and the harmonic response analysis. In addition, the dimensions and the constructions of the statically indeterminate plate and the mesh beam were chosen as the design parameters, to which the sensitivity of the whole mass, the maximum deformation and the maximum stress of the duplex statically indeterminate mesh beam structure (DSIMBS) were summarized for the optimization of the DSIMBS. Now the large-scale VSDSIMBS is being well used in China.

Jan 1, 2014

By Wen-long Zhan, Chun-en Zhu, Xiao-dong Du, Yong Zhao, Keng Wu

In view of the traditional evaluation index of sintering basic character- istics ignoring process information, several high temperature characteristic num- bers, which contain process information, were used to evaluate the sintering basic characteristics more comprehensively in this paper. The evaluation model of iron ore properties was established based on the high temperature characteristic numbers with employing fuzzy mathematics. Then, with the constraint of sinter properties and the raw materials, the ore blending model was built, whose target was to obtain the lowest cost and the best sinter properties. A multi-objective fuzzy linear pro- gramming was used to solve the model in order to get the best ore matching schemes. The ore blending model was then applied to the practical production, which was proved to be dependable.

Mar 1, 2018

By Ken Goering, Steve Kral, William Gleason

"Once every four years, the global mining industry gathers in Las Vegas, NV for MINExpo International. According to the show’s organizer, The National Mining Association (NMA), about 44,000 people attended the three-day show from Sept. 26-29. It was a show that featured the latest and greatest in equipment and technology. It also served as the backdrop for a snapshot of the state of the industry and while the picture of a global industry is never completely clear at any one time, one thing that is evident is technology has become a major force in the way mining is done.Had it not been for the awe-inspiring “iron” that was on the show floor in the form of haul trucks and shovels weighing hundreds of tons, one could be forgiven for thinking that they were at the Consumer Electronics Show. From training simulators designed to give a realistic experience of operating mining equipment to virtual reality technology that can take the user into the depths of an underground mine or the middle of a mapped ore deposit, an overriding theme of MINExpo 2016 was that the mining industry is connected like never before.In the north hall of the Las Vegas Convention Center was the GE Mining booth that was designed to showcase its efforts to help create a mine that will be connected from the front office to the face of the underground wall or bottom of the openpit. GE Mining called its booth a digital mine, and it included a suite of technologies that can improve performance, reliability, safety and operations. GE Mining said it views each mine as a mini-city, requiring power, water and transportation. Intelligent, real-time monitoring across the mine allows operators to make data-driven decisions that improve equipment reliability and optimize mine operations for substantial savings. And GE Mining was just one of many exhibitors showing off software that allows various types of equipment to communicate. Its booth sat in the shadow of the Komatsu booth with its new 360-t (400-st) 980E-4 haul truck that included GE’s 360-t (400-st) electric wheel motor. This is just one example of how technology is connecting machines, operations and people around the world and how mining is moving forward."

Dec 1, 2016

By F. S. Knoll

Magnetic separation employing superconducting technology is now accepted within the Kaolin processing industry, proving the value of this technology and its ability to operate reliably even at the most remote site. Developments in superconducting magnet engineering, including cryogen free operation, combined with experience in mineral processing enables new forms of Wet and Dry superconducting magnetic separation to be developed. Applying the high magnetic force advantages at 5 T else available from such magnets to other materials is now a reality. High magnetic force mineral separating system developments are reviewed allowing the mineral processor to take advantage of a technology that is no longer confined to the laboratory.

Jan 1, 1997

By Youngjib Ham

Understanding energy performance of existing buildings is vital to increasing their efficiency and reducing the overall energy consumptions. This entails facility managers to systematically monitor building energy performance and reliably identify and analyze potential problems. Currently, infrared thermography is widely used as a primary diagnostic tool for the detection of building performance problems. Nonetheless, applications of thermal images for building inspection are mainly restricted to manual and labor-intensive identification and qualitative assessment of heating or cooling loss. Automated identification of potential problems and reliable cost analysis of the associated energy loss can help homeowners to minimize financial risk of retrofits and maximize energy savings. To that end, this paper presents a new automated method for calculating the cost of energy loss for building diagnostics. In the proposed method, first, using a hand-held thermal camera, the auditors collect digital and thermal imagery from the buildings under inspection. Then, using a recently proposed method for Energy Performance Augmented Reality (EPAR) modeling, an actual 3D spatio-thermal model is generated and superimposed with a computational fluid dynamics (CFD)-based expected energy performance model. The resulting EPAR model is placed into the method proposed in this paper for cost analysis of the energy loss. Through a new 3D thermal mesh modeling using k-d tree structure and nearest neighborhood searching, performance deviations between these models are automatically calculated. Using a temperature threshold, the areas associated with potential performance problems are detected in the EPAR model and are visualized using a metaphor based on traffic light colors. Then, the actual R-values of the detected areas are measured at the level of 3D points. Based on the measured R-values and the estimated air change rate for the detected air leaks, (1) the heat loss or gain caused either by poor insulation or air infiltration/exfiltration and (2) the associated energy costs are automatically calculated. The proposed method is validated on several locations of existing residential buildings. The preliminary results show the potential of the proposed method for minimizing the inspection time as well as the risk associated with the cost analysis of retrofitting potential building performance problems.

Aug 1, 2013

By David Kress

Grinding mills, both autogenous and ball can be powered by several basic means. The three methods used today are girth gear drives, gearless drives and trunnion coupled reducers. This paper will focus on the first of these methods -girth gear drives. The girth gear drive has been used on thousands of mills which continue to operate successfully. These drives are noted for their simplicity and low cost. In the past, the horsepower capacity of girth gears has been slow to keep up with the horsepower increase required by the mill builders, particularly since the advent of the SAG mill. Gear manufacturers had capacity for 2000 HP mills in the 1950's, 5000 HP in the 1960's and 6500 horsepower in the 1970's. The 70's and 80's brought dual pinion girth gear drives which allowed mill sizes beyond 10,000 horsepower. Gear manufactures who could not keep up with the pace of the horsepower demands and the quality and reliability demanded by the mill builders and users have fallen by the wayside.

Jan 1, 1991

By I. Ward, E. Milosavljevic, M. Botz

"The silver nitrate titration method is a rapid and acceptably accurate means of analyzing for cyanide in leach solutions that contain primarily free cyanide. However, in leach solutions containing elevated levels of copper, the titrimetric method overestimates the concentration of free cyanide and underestimates the concentration of weak and dissociable (WAD) cyanide. The authors have developed a modified potentiometric (MP) titration method for determining WAD cyanide that overcomes issues associated with high copper levels in solution. The new MP-WAD method involves addition of a chemical ligand to the sample prior to silver nitrate titration to release cyanide bound to copper. Once released from copper, cyanide in solution is no longer affected by the presence of copper, and titration results are quantitative rather than empirical. In multiple laboratory trials with synthetic solutions and complex actual leach solutions, analytical results obtained with the new MP-WAD method were found to be within about ±5% of analyses obtained with the USEPA OIA-1677 WAD cyanide analytical method.IntroductionThe silver nitrate titration method is widely used to estimate the concentration of cyanide in leach solution for purposes of cyanidation process control. Cyanide determined by silver nitrate titration is commonly referred to as “free” cyanide, but frequently should be referred to as “titratable” cyanide. By definition, free cyanide is the sum of the concentrations of aqueous hydrogen cyanide HCN(aq) and the cyanide anion CN- (ASTM, 2010). Titration will only yield a reasonably accurate measurement of free cyanide when metal-cyanide complex concentrations (e.g., cadmium, copper, mercury, nickel, silver and zinc) in solution are low. In other words, titration will only yield a reasonably accurate measurement of free cyanide if the solution primarily contains free cyanide."

Jan 1, 2015

By T. A. de Almeida, M. de Paiva Bueno, M. Powell

The mining industry is one of the foundations of modern society, providing not only the raw materials needed to maintain a contemporary lifestyle, but also serving as a basis for the development of future technologies. From the most basic components of an appliance to the materials needed to design an electric car or a space rocket, each raw material has gone through a painstaking procedure of extraction and processing, and ways to make this process more efficient will be of great help to meet an ever-increasing demand for minerals. One of the biggest challenges when extracting mineral resources is to measure the variability of the mineral body prior to processing. Comminution is the most power-demanding stage, and the lack of geometallurgical testing, often for financial reasons, may result in an inefficient operation. The Geopyörä Rock Breakage test was developed with the objective of making mineral variability data more accessible by providing both standard comminution parameters and rock mechanical properties at low cost, and with a modest sample size, allowing a larger number of samples to be tested to reduce uncertainties and assure productivity. The objective of this paper is to present the results of an extensive validation of this new rock breakage method against two of the main tests currently in use, namely the SMC® and Bond ball mill work index tests. More than 100 samples have been tested and the results compared, showing that the new method can accurately estimate the parameters of the traditional tests. This confirms that the new test is a reliable tool for comminution and geometallurgical tests.

Feb 1, 2023

By M. G. Lipsett

One challenge in applying information technologies in Mining is building a business case. In Mine Maintenance, there is a complex flow of information that contributes to making informed business decisions. By understanding those information relationships and the cost of wrong decisions, analysts can estimate the value of information flow. Developers can then ensure that systems deliver key information in an accurate and timely way. In this paper, general maintenance decision-making is discussed, with examples of how model-based analysis can improve the information delivered to decision makers.

May 1, 2001

By P Minkkinen

"Pierre Gy showed in his early works that the results in estimating the variance of the mean value of continuous lots depends on sampling mode (random, stratified or systematic), except in the theoretical case that the measurand is randomly distributed in the lot. The experimental variance estimate calculated from samples taken from the lot is independent of sampling mode but depends on sample size and the type of the lot heterogeneity. Variography can be used to estimate the variance of the lot mean for different sampling modes.Gy also defined weighting error, which is made if a simple average is calculated from the assays of samples taken from a continuous object (eg from a process stream) where the flow rate varies with time and is correlated with the concentration of the analyte in the stream.The effect on sampling uncertainty of the three sampling modes and their interaction with the following factors in estimating the uncertainty of the mean concentration is studied using simulated lots, and lots having heterogeneity patterns similar to those of real data sets, including the effect of: the type of heterogeneity (random, grading and clustered heterogeneity patterns) increment size and number employing composite sampling weighting error. CITATION:Minkkinen, P, 2017. Dependence of the variance of lot average on the sampling mode and heterogeneity type of the lot, in Proceedings Eighth World Conference on Sampling and Blending, pp 319–330 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017

By J. Walter Snavely

PRESENT-DAY processing in many industries, calcining, sintering, briquetting, beneficiation and nodulizing, increasingly calls for the handling of large volumes of hot bulk materials. Various types of conveyors have been employed. This discussion will cover the factors governing their selection. For temperature ranges up to 400°F, or approximately 200 °C, a wide range of conveyors is available. Special constructions of rubber conveyor belts, steel conveyor belts, vibrating and shaker conveyors, apron conveyors, and drag chain conveyors, all are used successfully. As temperatures go well above 400 2F, however, choice of conveyors is narrowly limited. This paper will consider the problem of handling bulk materials only where the temperatures exceed 400°F. The arbitrary selection of 400 °F as a dividing point undoubtedly can be challenged, as special conveyor belting constructions are available which are suitable for temperatures in excess of 400°F. However, when the relatively short life of such belts and the cost of their replacement, with the attendant down time, are balanced against the reliability and long service life of the properly designed steel constructed units to be discussed, there is little question in any operator's mind that the special belts are more expensive to use. Because the conveyors under study are for the handling of bulk materials, inevitably including a high proportion of fines, obviously wire mesh belts cannot be included for consideration. Even though this type of conveyor is widely used at high temperatures, i.e., for carrying glassware through a lehr, it is unsuited for the conveying of bulk materials, and therefore will be excluded from further discussion in this paper. Preliminary to the study of the conveyor itself is the determination as to whether the material is to be cooled while it is being handled, or whether the processing requires retention of all heat and the maintenance of a given temperature range. In the majority of cases cooling is incidental to or part of the handling process, when the handling, for example, follows completion of sintering, roasting, calcining, refining, or some other process. To meet such operating conditions successfully, the conveying medium used must have: 1—a construction capable of withstanding maximum initial temperatures of the material being handled. 2—a construction providing efficient heat transfer for cooling. 3—a construction providing dependable operation and long life with minimum service requirements, and 4—a construction providing controlled and efficient conveying. Under the usual conditions of cooling during the handling, the construction selected to withstand the initial maximum temperatures does not necessarily involve using alloys, as excellent results can be achieved with normal carbon steels and cast irons, when they are properly applied and proportioned. The earliest and simplest type of conveyor for handling very hot materials is the cast steel drag chain conveyor, still widely used for handling hot cement clinker, as illustrated by Figs. I and 2. Because of the rugged and generous proportions of the chain link design, low carbon steels are entirely suitable for the links. The pins, however, must be alloy steel. The simple, rugged construction of this type of conveyor makes it readily capable of withstanding high initial temperatures, even though the chain is operating buried in the material. The drag-chain type of conveyor has advantages and limitations. Although the efficiency of the heat transfer is relatively poor, the life of the conveyor is reasonably long, and because of its crude simplicity it does not require much servicing. However, as a conveyor, it is limited in capacity, and largely limited to horizontal runs. Furthermore, because of the crude design, heavy weight, and the chain operating at the temperature of the material, greatly reducing permissible operating chain pulls, this type of conveyor is limited to relatively short centers. Another type of conveyor that has been used for very hot materials is the cast pan conveyor. Because of its very generous proportions the cast pan, which is made of either cast iron or malleable iron, can withstand initial maximum temperatures. It also provides efficient heat transfer for cooling. Further, it is on efficient conveyor construction, which can be used for inclines. Because the chain employs rolling friction instead of sliding friction, and is not in the maximum temperature zone, much longer centers are possible. It is this type of conveyor that is frequently used in the casting of various metal pigs, pig iron, and aluminum; it is obvious, therefore, that very high initial temperatures are being handled. With this kind of conveyor the return run is frequently sprayed with water to accelerate heat transfer. The build-up of residual heat in the very heavy cast pans is thus overcome. The outboard roller steel pan conveyor is an improved pan conveyor' which provides high rates of heat transfer and substitutes formed steel pans for the heavy cast pans. It is a very efficient conveying medium. The details of this particular construction are clearly shown in Fig. 3. An early application of this type of conveyor is shown in Fig. 4. In this case the conveyor units are handling roasted phosphate rock at average temperatures of 1000" to 1500°F, and frequent maximum temperatures as high as 1900°F. Several widths are used. The capacity of the unit at a speed of 50 fpm is approximately 30 tph per inch of width at peak loadings, average capacity being about 1/3 of peak loading. The assembled conveyor is shown in Fig. 5, with views of both the top and the underside to show all the construction details. In particular, the following general design principles were carried out in this construction:

Jan 1, 1954

By Arthur M. Langer

Since the promulgation of the first Federal Asbestos Standard by the Occupational Safety and Health Administration in 1972, other federal agencies have modified the standard to better carry on their own unique missions. The instruments used to identify and measure asbestos, the sampling protocol, and the criteria used to define asbestos, have been modified to some degree. The Mine Safety and Health Administration regulates and controls asbestos dust in the mining and mineral commodity industries. However, crushed stone and processed ores contain mineral fragments that are frequently difficult to distinguish from asbestos. Mineral nomenclature, instruments for particle analysis, and sampling strategy must be accommodated to some degree to make asbestos control workable and meaningful. Precedent in other agencies has made consideration of these changes possible. Newly identified amphibole asbestos minerals have further complicated the agency?s regulatory charge. Changes in its Asbestos Standard are now being considered. Crushed taconite ore in the Eastern Mesabi highlights many of these issues. ©2008 Published by Elsevier Inc. Keywords: Amosite; Grunerite asbestos; Crocidolite; Riebeckite asbestos; Tremolite asbestos; Actinolite asbestos; Winchite asbestos; Richterite asbestos; Arfvedsonite asbestos; Fluor-edenite asbestos; Asbestos defects; Cleavage fragment; Mineral habit; Mesabi amphiboles

Jan 1, 2008

By Houquan Zhang, Yu Wu, Yanlong Chen, Zhenfu Luo, Aihong Lu

"A non-destructive detection scheme for bolt installation quality was designed by adopting the method of non-destructive detection on bolt installation quality. Based on the field measurements, a random non-destructive detection method for determining the characteristic length including anchoring length, free segment length and initial axial load of bolt was discussed, and the characteristics of increasing bolt axial load in the initial stable stage was obtained. The results show that the bolt axial load and deformation of surrounding rocks correlate each other. Compared with the traditional detection technique for bolt installation quality, the non-destructive detection method has obvious advantages such as random, accuracy, and economic. The method provides a reliable basis for bolt support optimization and stability control of surrounding rocks.INTRODUCTIONBolt support in roadway can make the surrounding rocks and bolt form a structure in the early stage of roadway development through the bolt pre-tension, which can maximize the self-bearing capacity of surrounding rocks. Thus it is a form of active support (Kang, 2007). In order to make the bolt play an active supporting role, it needs to ensure the installation quality of bolting. Thus the bolts can supply a high initial anchoring force and control the deformation of surrounding rocks (Shan, 2009; Wei, 2012). Moreover, bolt supporting is a concealed work. Once installation quality problems appear; it will be difficult for effective detection and screening (Xie, 2008).THE PROBLEMS OF BOLT INSTALLATION QUALITY IN COAL MINE AND ITS DETECTIONThe Problems of the In Situ Bolt InstallationDue to the problems in installation environment, machine, and technique, and workers proficiency (Li, 2003), there are many problems exist in bolt installation. If the borehole depth is too long, the anchoring agent will accumulate at the bottom of the bore, which reduces the anchoring length. Furthermore, if the borehole depth is short due to the poor geological condition, the exposed part of the bolt will be too Jong and the pallet cannot cling to the rock face, which prevent the pre-tension from being applied. The pre-tension is very important for bolt installation. If pre-tension is insufficient the rock bolt cannot control the deformation of surrounding rock efficiently and the bolt anchoring force will decrease considerably. The bolt length is another important parameter for anchoring quality, which will affect the control area of bolt supporting. In addition, the cleanness of drill hole has a great influence on the effective anchorage length of bolt. If the drill hole cleaning is not enough, it will directly affect the anchoring agent and the contact area of surrounding rocks, which will decrease the effective anchorage length and initial anchor-force."

Jan 1, 2016

By Raymond W. Hiteshue, Sam Friedman, Martin D. Schlesinger

The Bureau of Mines in cooperation with the El Paso Natural Gas Co. investigated the effect of high temperature and pressure at short residence times on the hydrogenation of a New Mexico coal to gaseous and liquid hydrocarbons . The study was made in a bench - scale semicontinuous unit at pressures of 500 to 6,000 psig , 480 ° to 1,000 ° C , and residence times of less than 1 minute to 15 minutes . Ammonium heptamolybdate was impregnated on the coal to furnish 1 percent molybdenum based on maf coal . Coal could be rapidly hydrogenated at elevated temperatures and pressures to yield large quantities of gaseous hydrocarbons and small quantities of lowboiling oils , high in single - ring aromatics . At 800 ° C and 6,000 psig and a residence time of 1 minute , the yield of hydrocarbon gas was 43 percent and of liquid hydrocarbons 9 percent , based on maf coal . With a 15 - minute residence time , the yield of gaseous hydrocarbons increased to 68 percent with a decrease in yield of oil to 6 percent . At higher hydrogen velocities , the yields of oil were much greater but contained large quantities of asphaltene . Low concentrations of molybdenum (0.01 and 0.1 percent ) or a high concentration of iron ( 1 percent ) were ineffective at 800 ° C , 6,000 psig , and short residence time .

Jan 1, 1964

By K. Scalise, M. Teixeira, K. C. Kocsis, J. Parrish

"This paper aims to introduce and discuss a newly developed algorithm, which can be uploaded on smart watches and other mobile devices to inform and protect underground personnel working in hot and humid environments. Using this algorithm, the metabolic rate (M) of a worker can be determined in “real-time”. In addition, besides warning signs and alarm signals emitted by the smart watch, the algorithm has the ability to determine work-rest time periods based on the worker’s physiological parameters (e.g. age, height, weight, gender) and the climatic parameters (Td, Tw, flow velocity). This paper also investigates whether a re-designed auxiliary ventilation system can provide appropriate work conditions in the production stopes. INTRODUCTION An underground environment with high temperature and humidity conditions generated from various heat and moisture sources can significantly affect the thermoregulation processes of the human body. This can lead to heat-related illnesses such as heat rash, heat cramps, heat exhaustion, and heat stroke. Heat stroke is a serious illness that carries a high risk of fatality, if the underground workers are not immediately treated and the climatic conditions are not corrected (McPherson, 1993). There are two methods used to control the climatic conditions in underground mines: (1) Using ventilation and cooling systems to reduce the thermal stress on the mine workers, and (2) Reducing the heat transferred to the ventilating air from major sources such as: strata, auto-compression, mining equipment, groundwater, blasting, etc. The heat from strata and auto-compression is transferred to the ventilating air at varying degrees, based on factors such as the virgin rock temperature (VRT), the thermal properties of the surrounding rock formations, and the surface air temperature. However, the use of mining equipment and blasting processes can be managed to reduce their contribution to the mines’ overall heat load. To provide appropriate work conditions, selecting the most suitable cooling method depends on the level of heat to be removed, the location of the problem areas, and economic constraints (Brake & Bates, 2002; McPherson, 1993). Because every mine is unique, it is essential to monitor the climatic conditions to select the most appropriate method of cooling. A majority of the time, simply adjusting or re-designing the auxiliary ventilation system can efficiently remove the heat and dilute the contaminants. This may involve moving the ducting system, changing the size of the duct, changing the size of the auxiliary fan, or switching from forcing to an exhausting fan arrangement. If the required air volumes are higher than the existing primary ventilation system can supply, other measures may need to be taken to increase the airflow delivery. This may include regulating the flow in some areas of the mine to increase airflow to the desired area, adding booster fans, or replacing the primary fans."

Jan 1, 2019

By Burt G. Look, David W. Lacey

"Certification of foundation capacity during the construction phase is often assessed by strength or weathering state descriptors based on visual observations. This case study used the Point Load Index (PLI) test as a quantitative tool in the construction certification of a pile’s design capacity. Construction phase tests were completed on irregular sized rock samples whilst comparable design phase testing was completed on intact rock core samples. Statistical comparisons were made to assess the repeatability between the PLI tests, with best-fit Probability Distribution Functions (PDFs) determined for both datasets. Pronounced differences were observed based on the PDF adopted to characterize the PLI dataset, the consequence of which would be a significant change to the pile’s design capacity. The adoption of the lower quartile value is shown to satisfy both design conservatism and construction simplicity requirements. The commonly held belief that rock samples produced during socket excavation may be biased towards the higher strength portion of the rock mass, is shown to be invalid for this site. As the central bridge piers were certified using Plate Load Tests (PLTs), the resultant load-settlement relationships were compared with the PLI strength assessments made for similar materials recovered from the adjacent abutment piles.INTRODUCTIONThe upgrade of the Foxwell Road Overpass across the Pacific Motorway in South East Queensland required the duplication of an existing four span bridge structure. The foundations of the new bridge included the installation of 1.2m diameter cast in place (bored) piles at the bridge abutments and 900mm diameter cast in place (bored) piles below a retaining wall to be constructed adjacent to the existing abutment.The site geology was dominated by the Palaeozoic Neranleigh–Fernvale Beds, predominantly comprised of argillite, sandstone and greywacke. Limited soil materials existed at the site, with Extremely Weathered (EW) rock typically encountered within metres of the existing ground surface. The exception to the existence of shallow rock were locations where existing filling of the site had occurred – i.e. approach embankments to existing bridge structure.Capacity of pile sockets is typically assessed onsite by descriptive rock strength or weathering assessment. Such descriptors encompass a wide range of values and lack precision. Due to the subjectivity of such assessment techniques – a factor of 3 is often observed in terms of strength assessment based on one’s interpretation of rock strength descriptors alone – uncertainty on site often occurs regardless of whether a lower bound, average or other characteristic design parameter applies."

Jan 1, 1900

By S LeClair

Intelligent manufacturing involves intelligent, product-directed systems that facilitate the on-line, real-time generation of an improving product process cycle. A first step in the journey relates to self-directed systems which have the ability to reason and create their own processing paths in response to varying product and process conditions encountered during the process. This paper discusses an application of self-directed process control in the manufacture of graphite-epoxy laminated composites. An Air Force team involving researchers and production personnel have caused the development of a system now in use at the Air Force Logistic Center at McClellan Air Force Base in Sacramento CA. The paper discusses results and lessons learned in the process of trying to speed the implementation of research efforts which show significant potential of improving the product quality in less time and at less cost

Jan 1, 1992

By L. W. Blau

PERHAPS the most important event f or exploration geophysics in 1940 was the publication of three textbooks : "Geophysical Prospecting for Oil," by L. L. Nettleton ; "Exploration Geophysics," by John J. Jakosky; and "Geophysical Exploration," by C. A. Heiland. The literature had grown so bulky, and such a long time had elapsed since the publication of the texts by Ambronn and Eve, that treatises covering exploration geophysics comprehensively in all its branches and giving literature and patent references were sorely needed. This need has been satisfied admirably in these textbooks, and geophysicists owe the authors a debt of gratitude. In 1940, geophysics came of age. A conference on applied nuclear physics was held at Massachusetts Institute of Technology from Oct. 28 to Nov. 2. Several papers on geophysical subjects were presented at this meeting. Geophysical activity has decreased in all parts of the world except perhaps in Canada where, under the stimulus of the war's increased demands, prospecting for oil has increased. However, even there the war has had a seriously adverse effect on prospecting for ores and upon the promotion of new properties, although activity in producing and near-producing mines has been stimulated.

Jan 1, 1941