Search Documents

By Daniel Harrington

On the night of June 8, 1917, the flame of a carbide lamp accidentally set fire to the uncovered and frayed insulation of an armored power cable near the 2,400-foot level of the North Butte Mining CO.'s Granite Mountain shaft. How this, insulation accidentally became exposed is explained on page 15. The highly flammable oiled fabric set fire to the shaft timbers, and as this is a downcast shaft the fire spread with great rapidity, soon filling the mine workings with smoke and gas. At the time 410 men were working underground, 247 of whom escaped by various means, but most of the 163 remaining were probably overcome soon after the fire started, and perished. Only two men were actually burned. The cause of the disaster was purely accidental. The immediate effect was the unexpected reversal of normal conditions; the ultimate effect was great loss of life and the destruction of the main hoisting shaft, putting it temporarily out of service. The work of rescue and fire fighting continued eight days. The following pages present an attempt to draw some practical conclusions and suggestions from this disaster. The property of the North Butte Mining Co. consists of about 220 acres in the northeastern part of the Butte district, Montana. Next to the Anaconda Copper Mining Co. it is the largest producer of the district. In 1916, the year before the disaster, there were 1,160 men employed. The output was 560,947 tons of ore, which yielded 24,498,181 pounds of copper, 1,047,063 ounces of silver, 1,712 ounces of gold, and 412,953 pounds of zinc. The profit was $2,479,595. The total development work for that year was 21,694 feet. During the first half of 1917, the year of the accident, the daily tonnage of ore averaged 2,000, an increase of 400 tons over that of the year 1916.

Jan 1, 1922

By Henry C. Meeves

The Bureau of Mines investigated the silver production potential of the Leadville (California) mining district, Lake County, Colo., in 1966-67. The mining history of the district, the ground conditions encountered in mining, and the mine-support methods used are reviewed. The drainage problem is discussed in detail. An initial objective was to establish the existence of potential silver resources minable by low-cost open-pit methods, particularly in the silver-bearing manganese halos surrounding the major deposits. The report concludes that under present conditions, development of the deposits in the area is not economically feasible; however, a pioneer rotary noncore drilling program demonstrated that this type of exploration is technically feasible. Potential reserves of silver and associated metals are estimated. Possible mining methods for recovery of the reserves are discussed. Future production possibilities from the various subareas of the district are analysed, considering optimum operating size. Consolidation of small individual holdings for unit operation is recommended. Type of operation, amount of rehabilitation, size and type of concentrating plants required, drainage and other mining problems, and metal price trends are discussed as they bear on economic feasibility of development.

Jan 1, 1970

By Frederick C. Trutt

This report is intended as a reference for personnel interested in the computer anlaysis of coal-mine-electrical-power systems under either normal operating conditions or fault situations. The procedures developed for this purpose are described and implementation considerations are discussed with respect to the mine-power system. Considerations for choosing a solution technique and a number of examples are included. Procedures described include the Newton-Raphson iterative technique for the analysis of normal operation as well as a non-iterative Z-bus technique for analysis of unbalanced or balanced faults. During program development, strict attention has been given to the inclusion of core and/or time saving techniques such that these algorithms may be implemented on small as well as large computers. Program languages include FORTRAN IV for batch processing applications and APL or BASIC for interactive applications.

Jan 1, 1981

By Robert D. Ewing

The computer program described in this user's guide provides for the static, three-dimensional, linear and nonlinear analysis of structural and geological systems by the finite element method. The guide describes the capabilities and general features of the program and shows how input is prepared. A number of recent advances in finite element theory and computer technology are incorporated in the program. Nonlinear material properties are provided for, including isotropic, anisotropic, and time-dependent material properties, gravity loading, simulation of a sequence of excavation or construction, and a slip or joint element. The finite elements include beam, rod, axisymmetric and plane quadrilateral, hexahedron, thick shell, and axisymmetric and plane joint. The program also has an automatic mesh generator to minimize user input preparation for continuum finite element meshes.

Jan 1, 1976

By J. W. Thompson

This work is a codification and annotation of the Congressional enactments relating to minerals, mineral lands, and mining. It covers every enactment of Congress from the original ordinance of 1785 to the present time, as well as all sections of the Revised Statutes of the United States relating to these subjects. These laws are grouped according to their general subject matter, and are arranged thereunder in numerical or chronological order. Many of the mining statutes include matter not pertinent to the subject, and only those parts of such acts are quoted as will properly show their relation to minerals and mineral lands and indicate how they should be construed. Some mining acts have been repealed or have become obsolete, and others have become incorporated substantially in sections of the Re- vised Statutes; but these are retained in order to show the changes made, and the constructions placed thereon by the courts are given as aids in construing the new or repealing acts. The annotations consist of legal propositions abstracted from the decisions of the various courts and executive officers of the Govern- ment that have interpreted the sections and statutes so codified. These legal propositions are arranged under the different sections and acts with appropriate headings, titles, and subtitles, in logical order, exhibiting the present status of each particular section or act and its application to the subject of mines and mineral lands. The annotations do not purport to be abstracts of decisions on the sub- stantive law of mines and mining generally, but are limited strictly to the interpretation placed on a given section or act definitely re- ferred to by a court or executive officer by the number of the section of the Revised Statutes or the volume and page of the Statutes at Large in which the Congressional enactment is found. It may be observed that the legal propositions stated are not always pertinent to the particular section or act under which they are classed and of which they purport to give a construction. The arrangement, however, is not an arbitrary one, but is so made for the reason that the courts or officers in the construction of a particular section or act definitely referred to by number or volume and page incorporated in the decision matter not strictly pertinent to the par- ticular section or act so designated. This statement applies especially to the interpretations placed on the sections of the Revised Statutes. The decisions abstracted for the purpose of this work are those of the United States Supreme Court, 234 volumes; the various Federal courts, 214 volumes; the decisions of the Department of the Interior

Jan 1, 1915

By John M. L Lewis, Antoine F. Mulaba-Bafubiandi

In the irradiation of ore particles by microwave energy preferential absorption of this energy occurs in minerals having specific dielectric properties (Bradshaw, 1999). This leads to a selective heating of the various components of within the ore particle matrix. The result is a differential thermal expansion of such components and the resulting induced stresses become ideally concentrated at mineral grain boundaries (Kingman et al., 2000). Dependent upon the relative composition of absorbent, opaque and reflective components this may lead to enhancement of the inter-granular fracture of the ore particles in the initial comminution process (Fandrich et al., 1997). The potential is thus a greater proportion of free mineral grain within the fractured ore particle that may lead to improvement in subsequent mineral separation processes. As the composition of the ore dictates the result of such a treatment (Kingman et al., 2000) it is essential to evaluate the response of each ore sample on an individual basis. This paper reports on results obtained from two ore samples: the one being the zinc ore from the Black Mountain mine (South Africa) and the other a pre-concentrated sample of handpicked cobalt?copper mixed oxide ore from the Gecamines (DRC). The equipment and methods used to simulate the comminution of the samples and evaluate the level of the value liberation will be described along with the results obtained. Using King (1975), Kanellopoulous and Ball (1975), and Gungor and Atalay (1998), a comparison between the behaviour upon microwave irradiation of sulphide and mixed oxide ores leads to conclude that while the technique (i.e. microwave irradiation) is appropriate to the zinc sulphide ore, it does not seem to lead to exceptional results for the oxide.

Jan 1, 2005

By Dave Bulled, Jim Thompson, Tim Leriche, Mark Blake, Troy Wilkie

"A commitment to a core testing, plant modeling and reconciling technique has shown substantial economic benefits to IOC in terms of accurate production forecasting, smoother operation of the mill, improved expectations of throughput and co-operation across production departments from geology, planning, mining, and processing, to shipping of concentrate to market.This paper describes a successful seven year program of forecasting throughput of the autogenous milling circuit at the Carol Lake concentrator of IOC. Work started with audits of the grinding circuit in 2001 and benchmarking of the data collected from samples of mill feed and plant operation to the CEET mill design and throughput forecasting model.Initially 390 drill core samples were tested for SAG Power Index (SPI) to measure the energy required in milling, and the data distributed using a geostatistical technique across the two operating pits, so that hardness was estimated in each of the 40,000 blocks (or 1500 million tons) of potential ore. In 2004 a forecast of energy requirement, i.e. forecast of throughput for a given power availability at the mill, was produced for each ore block using the CEET model and used for mine planning to smooth plant throughput. The forecast for blocks mined on a monthly basis was reconciled with plant results over the next 2 years and minor changes made to the CEET model. The forecasting exercise was repeated in 2006 and in 2008 with the latest model based on the testing of almost 1300 samples of drill core at closer spacing.INTRODUCTIONThe contracting of sales to clients and the timely supply of products to meet those contracts is a cornerstone of good business practice. Ensuring the correct scheduling of production is a major concern of mining companies where the supply and qualities of the raw material is uncertain and production facilities are not flexible. This is particularly challenging when the product is of high volume and produced far from the customer, such as iron ore.Apart from the metal content of the ore being mined, the greatest impact on production scheduling is the throughput of the comminution section of the extraction plant; most notably when size reduction is achieved by autogenous grinding. The response of the mills to variability in the hardness of the ore can change throughput by as much as 50% from day to day at some plants."

Jan 1, 2009

By Nan Wang

Based on the commercial computational fluid dynamics software, Fluent, the fluid flow and temperature field in an iron-bath reactor were simulated numerically, and the effects of top-blown and side-blown operating parameters on the mixing time of iron bath, distribution range of oxygen in top space, and post-combustion ratio were investigated. The simulated results showed that the mixing time of iron bath increased initially and then decreased with the increase of inclined degree and immersion depth of side-blown lance. The distribution range of oxygen became wider as pulling the top lance away from the iron bath. Furthermore, post-combustion ratio was reduced given the top lance was too close the bath. The simulation results provide theoretical base for the process optimization of iron-bath reactor and further development of new type iron-bath smelting reduction process.

Jan 1, 2009

By Craig Naudé

"An enhanced gravity concentrator was installed in conjunction with an Intensive Leach Reactor at the Sadiola plant in Mali last year and commissioned in Dec 2007.There has been much debate over the years as to the effect of gravity concentration on overall plant performance. The late Dr Laplante suggested that for every 10% of gold recovered by gravity, there was a corresponding 0.1% to 1% additional overall plant recovery. The results at Sadiola are consistent with this hypothesis with an overall 4% gain in plant recovery.With total gold recovery of 12% in the gravity section, grades are increased from 3.54g/t in the gravity feed to an average of 2 600g/t in the concentrator feed to the in-line reactor. The recovery of gold in the in-line reactor is in excess of 98.5%.This paper discusses the background to the project, the laboratory testwork prior to the equipment selection, the operational results of the system, as well as the benefits of the future application of high mass yield centrifugal concentrators in base metals, sulphides and industrial minerals. Bench scale, pilot scale and plant practice examples are also presented.INTRODUCTIONBesides picking nuggets off the ground or out of riverbeds, gravity concentration is arguably one of the oldest methods of recovering gold. In circa 6000BC people discovered that gold can be found behind the rocks and in depressions of creek beds. By placing rocks in a stretch of channel with the proper slope the first sluice is built, probably around 4,000 BC, and this method is still practiced today."

Jan 1, 2009

By G. Onal, E. Gock, H. Dincer

"During the conventional chromite dissolution process; chromite ore concentrates were ground to at least <90 µm using the ball mill and after adding Na2CO3 and leaning material (instead of CaCO3 also residues from the leaching process) at a ratio of e.g. 1:0.75:1.2, depending on the specific formulation, follows the digestion e.g. in a rotary kiln, heated in countercurrent. The reaction time is 3 to 8 h. The calcine is comminuted and leached with water or a thin chromate solution. Depending on the type of ore used, the yield is 75-85 %. The disadvantage of the above-described process is that it is impossible, using current technology, to achieve a complete digestion of the chromite ores and that the chromium-containing residues have to be disposed of as special waste, involving a large financial effort.The subject of this study was the investigation of the effect of vibratory milling on chromite dissolution. The impact stress in the vibratory mill causes the mechanical activation of chromite, which is characterised by lattice defects. The degree of mechanical activation can be quantified by measuring the relative X-ray diffraction intensities at the parent lattice planes of chromite. Each relative X-ray diffraction ratio correlates with a certain degree of digestion. As opposed to vibratory milling, a complete digestion of chromite using a ball mill is impossible, even at extremely long grinding times.In this investigation a chromite concentrate from Pulpinar/Kayseri with content of 44 % Cr2O3 and the Eccentric Vibratory Mill was used. In order to verify the effect of the vibrating grinding on chromite dissolution, reaction kinetic investigations on digestion and leaching were carried out."

Jan 1, 2003

By R. L. Derick

On a regular basis, mine personnel should obtain air samples directly from active underground areas as well as remotely from sealed locations. These samples provide mine officials with data relative to the makeup of the various atmospheres. Should conditions underground change, these results can provide a baseline that can assist officials in determining the extent of change. Relating the concentrations of individual gases to time, applying gases to equations, and examining their change over time are tools that have been successfully used to determine if a heating event exists and, if so, the extent of the emergency. These atmospheric status equations have either been developed for the mining industry or adapted from other industries. They serve as tools to assist personnel in determining the condition of underground mine atmospheres. As long as the problem area continues to be ventilated, certain gases, gas ratios, and equations can be used to determine if a fire exists, what type of material could be burning, and what quantity of coal is burning. Once the mine or the involved section has been temporarily sealed, gases, ratios, and gas-derived equations can assist personnel in determining how conditions within the sealed volume are changing over time. To alleviate potential explosions when fresh air is once again introduced into the sealed volume, equations and a diagram have been developed to predict the likelihood of an explosive atmosphere. Similarly, prior to commencing recovery of a mine or section, equations exist that can assist in determining if the fire will rekindle when air is reintroduced. This paper serves as an overview to remind and/or instruct readers about gas-sampling methodologies and gas analyses to assist in determining the status of underground atmospheres.

Jan 1, 2006

Future climate variability and change will impact on mining operations and their attendant communities. To minimise this impact, early and informed risk management is warranted. However, research into the risks posed by climate to the Australian mining industry has so far been limited. We are conducting a systematic study of the mining life-cycle to identify the main areas of vulnerability and adaptive capacity of operations and communities. This project aims to assess what adaptation activities are currently being undertaken within the mining industry and its communities across Australia and to develop a risk management approach that will aid the adaptation of practices in and around the industry, better assuring the security of people, jobs, revenue and the environment under changed or extreme climate conditions. The Canadian mining industry was recently assessed through a similar study, which found that many mining companies perceive a real risk to mining from climate change in the future, despite few companies being actively involved in managing such risk. At a workshop held by CSIRO involving mining specialists, the most vulnerable stage in the mining process in the Australian context was assessed to be production. In particular, impacts on water and energy supplies and also transport and infrastructure were of high concern. Additionally, heat stress on workers and equipment, changes in groundwater flow and increases in geohazards were also identified as important factors in the short and long term if problematic climate events become more extreme or more frequent. Risks in the planning and post-mine stages were also identified. Based on literature reviews and preliminary discussions with mining experts, here we present an initial assessment of the climate adaptation issues relating to mining and its associated communities and describe our future work plans in this area.

Jun 1, 2010

By D. Brisebois, J. M. Fecteau, S. Poirier

"This paper focusses on new developments regarding thermal rock fragmentation applications. The technology consists of a strong burner powered by diesel fuel and air. The thermal reaction that is created allows for the enlargement of 125 mm to 450 mm holes by breaking the rock in a spalling effect. It has been used for over 30 years in Russian open pit mining. Following an agreement between Dynamitage T.C.G. Inc. and the owner of the technology, major improvements have been brought to this technology, allowing for the fabrication of a prototype suitable for the Canadian industry. In Russia and the Ukraine, thermal rock fragmentation is actually used to drill large diameter holes in surface mining. Upon having acquired a better knowledge of this technology, it seems that it presents a great potential for selective mining in narrow-vein operations, for either surface or underground mining.Rocmec International Inc., a subsidiary of Dynamitage T.C.G. Inc., and Natural Resources Canada are technical partners in the evaluation of the operational parameters and environmental aspects such as gas, heat, dust and fog emissions. Furthermore, Canada Economic Development is a financial partner in this project.This paper presents the technology and its history. It also reports on the changes brought to the equipment to adapt it to North American environments. A summary of the tests carried out since 1995 is provided, along with the main conclusions obtained. The anticipated applications for the use of this technology in both surface and underground environments are described such as open pit mining, bulk sampling and narrow-vein ore extraction. An estimate showing a comparison between the thermal fragmentation mining concept and the long-hole mining method is presented and, finally, the future developments planned are listed."

Jan 1, 2003

By R. L. Derick

On a regular basis, mine personnel should obtain air samples directly from active underground areas as well as remotely from sealed locations. These samples provide mine officials with data relative to the makeup of the various atmospheres. Should conditions underground change, these results can provide a baseline that can assist officials in determining the extent of change. Relating the concentrations of individual gases to time, applying gases to equations, and examining their change over time are tools that have been successfully used to determine if a heating event exists and, if so, the extent of the emergency. These atmospheric status equations have either been developed for the mining industry or adapted from other industries. They serve as tools to assist personnel in determining the condition of underground mine atmospheres. As long as the problem area continues to be ventilated, certain gases, gas ratios, and equations can be used to determine if a fire exists, what type of material could be burning, and what quantity of coal is burning. Once the mine or the involved section has been temporarily sealed, gases, ratios, and gas-derived equations can assist personnel in determining how conditions within the sealed volume are changing over time. To alleviate potential explosions when fresh air is once again introduced into the sealed volume, equations and a diagram have been developed to predict the likelihood of an explosive atmosphere. Similarly, prior to commencing recovery of a mine or section, equations exist that can assist in determining if the fire will rekindle when air is reintroduced. This paper serves as an overview to remind and/or instruct readers about gas-sampling methodologies and gas analyses to assist in determining the status of underground atmospheres.

By Yavuz Ali Topkaya

Rare earth ferrosilicide is a versatile alloy mainly used to control the detrimental effects of sulfur in steel and to modify graphite structures in cast iron. The aim of this study was to determine the optimum conditions to make rare earth ferrosilicon alloy using a preconcentrate produced from a bastnasite type of ore present in the Beylikahir-Eskisehir region of Turkey. This concentrate contained 23.5%REO, 41.37% CaF2, 10.69% BaSO4, 8.50% CaCO3, 4.18%Fe2O3, 2.83% Al2O3, 2.74% SiO2, 1.20% P2O5 and small amount of other oxides. The initial metallothermic reduction of this concentrate using ferrosilicon and aluminum in a graphite crucible placed in a muffle furnace gave very low recoveries due to the difficulties encountered in adjusting the slag composition, temperature and amount of additives. Therefore, two batches of rare earth oxide concentrate containing 61.1% and 81.7% cerium oxide, respectively, that were procured from a Turkish glass producer, were used to optimize with respect to temperature, duration, slag-making additives and amount of reducers. In these experiments, smelting and reduction was done in an induction furnace with graphite crucible, and, ferrosilicon and aluminum were added after melting the charge. As a result, there was no difficulty in obtaining a rare earth ferrosilicon alloy containing 35-55% RE, 5-25% Fe and 20-40% Si, with about 80% metal recovery. When the optimum conditions were applied to the preconcentrate, alloys of similar compositions were obtained with 70-80% recovery. Experiments were also done with mixtures of preconcentrate and rich concentrate, and, recoveries as high as 95% were obtained. Only in this case, to increase the recovery, mixtures had to be charged to the empty graphite crucible after heating the crucible to the required temperature.

Jan 1, 2006

By Russell A. Fields

Barite (BaS04) is an industrial mineral with hundreds of uses. It is primarily used as a weighting agent in drilling fluids. This use comprised approximately 97% of U.S. barite consumption in 1981. Barite is found in three types of deposits: bedded, residual, and vein. Bedded deposits, because of their relatively large tonnage, have been the principle target of explorationists. Increased demand for barite in the mid to late seventies prompted many companies to significantly expand their efforts in barite exploration. Barite exploration techniques currently range from outcrop walking and geochemical exploration to gravity and seismic surveys.

Jan 1, 1983

By John R. Dudo

The Bureau of Mines Morgantown Petroleum Research Laboratory, with the cooperation of the Penn York Oil Company, cored the Dewdrop, Bradford Third, Lewis Run, and Sartwell sands in the Sartwell oilfield, McKean County, Pa. This report contains a review of the geology and depositional history of the field and an evaluation of the feasibility of secondary recovery of oil from the Bradford Third and Sartwell sands by waterflood or gas drive. Core analysis, geologic data, and electrical and radioactivity logs were used to evaluate the reservoir characteristics. Reservoir geometry, rock properties, fluid characteristics and saturations, and relative permeability-saturation relationships were used to assess the floodability of these two sands. The results of this study indicate that between 53,000 and 61,000 barrels of oil can be recovered by water or gas injection. The success of a waterflood or gas drive will depend on the field injection rates of the reservoirs comprising this oilfield. Following an economic evaluation, additional field work is recommended to further test the floodability of the reservoir.

Jan 1, 1967

By Robert D. Brown

The purpose of this paper is to tell a story - and it is a story with a moral. My topic is Present Trends in the Tax Environment Affecting Mineral Development in Canada, and the first thing to recognize is that, with depressed metal prices and weakening western economies, taxes, in and of themselves, are not really the cause of the Canadian mining industry&apos;s present doldrums. But the character and level of mining taxes in Canada has had a profound influence on the development of the industry over the past decade, and the expectations of what taxes the industry will face in future years will influence the industry&apos;s further growth. My theme today is that, in Canada, our tax system has, in the past, served as a negative and destabilizing influence in the mining industry: it has contributed to a major short-fall in investment commitments and hence in the contribution which the mining industry can make to the Canadian economy, and the adverse effect on the industry of previous high tax rates was made far worse by the confusing, contradictory and perverse nature of the tax system itself. This is a story with some happy parts in it, and, in fact, governments in Canada did learn, haltingly and grudgingly, that there are limits on the amounts that governments could safely extract from the industry, and that some assurances of long term fiscal stability were necessary if investors were to be induced to make massive commitments which could only be recovered over very lengthy periods.

Jan 1, 1982

By R. M. G. Machunter

Computer models of metallurgical circuits are extensively utilised in design, and prediction of overall plant separation performance. As always, in the final optimised flowsheet design there is a compromise between the recovery of values and grade of the circuit output. This paper mathematically examines various circuit options for the generation of a heavy mineral concentrate from a generic mineral sands wet concentrator plant. Based on data derived from testwork, any particular mineral sand has a unique release curve describing the separation performance of the heavy mineral suite. Models are constructed that combine particular stage output streams as feed to other stages in various configurations. The ramifications of each option are discussed and reasons why one particular option is selected over the others examined.

Jan 1, 2005

By Davis M. Lapham

Ore bodies at Cornwall, Pennsylvania, have been mined since 1742 principally for iron from magnetite, but also for copper (in chalcopyrite), silver (in chalcopyrite), gold (in chalcopyrite), cobalt (in pyrite), sulfur, and crushed limestone aggregate. Metallization occurs as a limestone replacement above the essentially conformable, south dipping portion of a discordant saucershaped diabase sheet. Pre-Triassic and Triassic faulting have emplaced host Cambrian limestone and two Ordovician(?) hornfels units, now for the most part resting above diabase. Thermal metamorphism of carbonate-bearing country rocks largely to calc-silicates, is ubiquitous. Metasomatism, particularly of potassium, is unique to ore zones. Associated magnetite- actinolite mineralization replaces, in a preferential sequence, all earlier metamorphic and metasomatic minerals and rarely diabase chilled margin. Mineralogical (diopside, actinolite, mica, sulfides, oxides) and chemical (Fe, Cu, S, Co) zoning of the eastern ore body is focused down dip, near its western edge, along a major vertical fault through diabase. This zoning is spatially related to magnetite veins in diabase, to an ore body within diabase, and to a shear zone that probably extends through the sheet.

Jan 1, 1968