Search Documents

By Irwin Politziner F. M. Townsend, L. S. Reid

Recently published data indicate that the water vapor content of a gas, as determined by dew point measurement, is inaccurate when the gas has been dehydrated with diethylene glycol. Water vapor contents and dew point measurements of gases dehydrated with triethylene glycol have been obtained in this investigation in order to determine the magnitude of a similar error, if one exists. Experimental data show a very low concentration of triethylene glycol vapor in gases dehydrated at atmospheric ternperatures and pressures ranging from 500 to 2,500 psia and that the accuracy of dew point measurements is not impaired by the presence of triethylene glycol vapor. INTRODUCTION Nearly all natural gas transported by pipe line to northern and eastern markets must be dehydrated to a low residual moisture content in order to assure maximum transmission efficiency and continuous delivery under peak load conditions. Without dehydration, water vapor often condenses in pipe lines in quantities sufficient to restrict the flow3 and. under low atmospheric temperature conditions, gas hydrates may form and plug gathering. transmission and distribution facilities. Gas may be dehydrated to pipe line specifications by a number of methods. The most widely used methods are (1) adsorption of water vapor on a solid dessicant such as activated bauxite, alumina or silica gel,' (2) by absorption of water vapor by either diethylene or triethylene glycol-water solutions of high glycol concentration,11,13 and (3) by simultaneous expansion-refrigeration of very high pressure gas in which gas hydrates are purposely formed and then quickly decomposed.'"" Of these three fundamental methods, the adsorption and absorption processes provide the bulk of the dehydrated gas moving to market at the present time. The expansion-refrigeration process. a relatively new development, is gaining in favor because of its simplicity but is sharply limited in its application by available differentials between source and gathering system pressures. Where gas sale or purchase contracts contain a maximum water vapor content specification, the water vapor content is usually determined by measuring the dew point of the gas at system pressure. Knowing he dew point temperature and the system pressure, the water vapor content of the gas is determined from a graphical correlation of saturation, or dew point, temperature us the water vapor content of the gas which is customarily expressed as pounds of water vapor per million cubic feet of gas measured at 14.7 psia and 60°F. Dew points are usually measured with the U. S. Bureau of Mines Dew Point Tester. shown in Fig. 1, which is well suited for use at temperatures lower than 120°F and at pressurei; ranging from atmospheric to 3,000 psi. A number of correlations of dew point temperatures vs water vapor content are available,3,5,15 the most recent of which is that by McCarthy et al.4 Where natural gas is dehydrated by absorhing contact with concentrated diethylene glycol-water solutions. considerable difficulty is experienced in observing water dew points due to condensation of liquid hydrocarbon and glycol films on the mirrored surface of the dew point tester. Riesenfeld and Frazierl2 report that the dew point method for determining the water vapor content of a dietllylene glycol-treated natural gas is in error due to the glycol content of the condensate formed on the tester mirror, and that the water vapor content of the gas tested is actually lower than that indicated by the standard' dew point-water vapor content correlation. Extensive experience in testing gases dehydrated by concentrated triethylene glycol-water solutions lias not revesled difficulties of the nature cited above for diethylene glycol. Water dew points are clear and sharp and condensation of

Jan 1, 1951

By J. B. Macelwane

Historically whenever application of scientific results to a new problem required the special experimental background, the economic outlook and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering based on the professional requirement grew up in the engineering colleges. This is precisely what is happening now in geophysical engineering. THE Mineral Industry Education Division of AIME has long been interested in geophysical education. Organized in 1938, a Committee on Geophysical Education presented a number of reports in succeeding years. The AIME is an engineering society; hence it might be expected that the interest of the Mineral Industry Education Division would have centered about the relation of courses in geophysics to engineering education. However, this was not the case. The burden of the discussion held under the auspices of the Committee on Geophysical Education bore on geophysics in general and particularly on its relation to geology. In the decade that has passed since those meetings much water has flowed under the bridge. Not only have the geophysical sciences developed at an extraordinarily rapid rate but the practical importance and the range of their applications have spread in ever widening circles and have even assumed a very prominent place in research programs of the military, the Army, the Navy and, particularly, the Geophysical Research Directorate of the Air Force at Cambridge, Mass. So enormously have the geophysical sciences as such grown in scope and in degree of specialization that no one man in a lifetime of study can hope to master the theoretical and experimental complexities or even to follow intelligently in the published literature all the varied accomplishments of basic research in these fields. As in the other sciences, most of the results of geophysical research have potential economic value and are being applied to a wider and wider range of human needs. Here we see a parallel with the older sciences and their relation to engineering. Whenever the applications of scientific results required the special experimental background, the economic outlook, and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering grew up in the colleges and universities. In the words of the "Report of the Committee on Adequacy and Standards of Engineering Education" in the January 1952 number of the Journal of Engineering Education: "Engineering education in America was not developed after a preconceived plan. It evolved in parallel with the needs of a growing country, a country engaged in the development of a vast industrialization. From the first it filled a practical need, and its design emanated largely from an evaluation of the professional requirement." The advent of the railroad created a need for scientifically trained engineers and the response was the curriculum in civil engineering. The development of steam power created the demand for a curriculum in mechanical engineering. Neither of these types of engineers was trained to cope with the requirements of electrical power, and so there came to be a curriculum in electrical engineering. The advent of radio communication and of electronics during the first World War and in the years that followed resulted in the establishment of electronics engineering, sometimes within the curriculum in electrical engineering and sometimes independent of it. The complexities of industrial management have created an ever increasing demand for industrial engineers and the consequent building up of a curriculum in industrial engineering. The wide industrial application of chemical processes required a type of engineer whose background was training in chemistry but who was able to design processes and plants on an industrial scale; hence we have the curriculum in chemical engineering. The advent of the airplane created an entirely new set of problems which were solved by the training of aeronautical engineers. Many of these have called for more and more science and mathematics. Such was the history of the older engineer-

Jan 1, 1953

By J. B. Macelwane

Historically whenever application of scientific results to a new problem required the special experimental background, the economic outlook and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering based on the professional requirement grew up in the engineering colleges. This is precisely what is happening now in geophysical engineering. THE Mineral Industry Education Division of AIME has long been interested in geophysical education. Organized in 1938, a Committee on Geophysical Education presented a number of reports in succeeding years. The AIME is an engineering society; hence it might be expected that the interest of the Mineral Industry Education Division would have centered about the relation of courses in geophysics to engineering education. However, this was not the case. The burden of the discussion held under the auspices of the Committee on Geophysical Education bore on geophysics in general and particularly on its relation to geology. In the decade that has passed since those meetings much water has flowed under the bridge. Not only have the geophysical sciences developed at an extraordinarily rapid rate but the practical importance and the range of their applications have spread in ever widening circles and have even assumed a very prominent place in research programs of the military, the Army, the Navy and, particularly, the Geophysical Research Directorate of the Air Force at Cambridge, Mass. So enormously have the geophysical sciences as such grown in scope and in degree of specialization that no one man in a lifetime of study can hope to master the theoretical and experimental complexities or even to follow intelligently in the published literature all the varied accomplishments of basic research in these fields. As in the other sciences, most of the results of geophysical research have potential economic value and are being applied to a wider and wider range of human needs. Here we see a parallel with the older sciences and their relation to engineering. Whenever the applications of scientific results required the special experimental background, the economic outlook, and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering grew up in the colleges and universities. In the words of the "Report of the Committee on Adequacy and Standards of Engineering Education" in the January 1952 number of the Journal of Engineering Education: "Engineering education in America was not developed after a preconceived plan. It evolved in parallel with the needs of a growing country, a country engaged in the development of a vast industrialization. From the first it filled a practical need, and its design emanated largely from an evaluation of the professional requirement." The advent of the railroad created a need for scientifically trained engineers and the response was the curriculum in civil engineering. The development of steam power created the demand for a curriculum in mechanical engineering. Neither of these types of engineers was trained to cope with the requirements of electrical power, and so there came to be a curriculum in electrical engineering. The advent of radio communication and of electronics during the first World War and in the years that followed resulted in the establishment of electronics engineering, sometimes within the curriculum in electrical engineering and sometimes independent of it. The complexities of industrial management have created an ever increasing demand for industrial engineers and the consequent building up of a curriculum in industrial engineering. The wide industrial application of chemical processes required a type of engineer whose background was training in chemistry but who was able to design processes and plants on an industrial scale; hence we have the curriculum in chemical engineering. The advent of the airplane created an entirely new set of problems which were solved by the training of aeronautical engineers. Many of these have called for more and more science and mathematics. Such was the history of the older engineer-

Jan 1, 1953

By D. F. Gibbons

THIS investigation was undertaken in order to gain further information on the mechanism of plastic deformation of iron at temperatures between room temperature and 77.2°K, and also to contribute to our understanding of the low temperature brittleness phenomenon that occurs in both the tensile and impact tests. It was decided to study as pure an iron as possible and to use the tensile test in order to simplify the problem as much as possible. Two series of iron were used throughout the investigation: iron A, obtained from the National Research Corp. and supplied as gas-free, high purity iron; and iron B, obtained from Fast' and produced by melting iron under purified hydrogen. Typical analyses of samples of both irons, after fabrication, are given in Table I. The main difference in composition of these irons is in their nickel and oxygen contents. Nickel has a very large solid solubility in iron. However, oxygen has an extremely small solid solubility. An attempt was made to reduce the oxygen content still further by remelting under purified hydrogen. This was successful in reducing the oxygen content to -0.0006 pct. However, no results on tests of this iron are included, since difficulty was encountered in fabricating the ingot. Wire specimens 1 mm in diameter were used for the investigation. The wires were produced from the ingots, as supplied, by cold rolling and swaging, with intermediate vacuum anneals at 700°C. Care was taken to reduce preferred orientation in the wires to a minimum by keeping the percentage of reduction in area between anneals of 30 to 40 pct. X-ray transmission photographs showed no indication of preferred orientation. The final grain size of iron A was 20 to 24 grains per linear mm and of iron B, 16 to 18 grains per linear mm. All specimens were tested in the decarburized and denitrided condition unless otherwise stated. The procedure was to pass hydrogen, saturated with water vapor at 26oC, over the specimens at 730°C for 2 hr. The specimens were quenched in iced water and then annealed in a vacuum of - 5x10-6 mm Hg for one day at 560°C to remove hydrogen. Higher temperatures were used for the vacuum anneal but this temperature was found to be quite satisfactory in removing hydrogen. The specimens were slow-cooled after the vacuum anneal. Where it is stated that the specimens were carburized, the specimens were given an identical decarburizing treatment and then carburized by passing hydrogen, saturated with pure n-heptane vapor at 0°C, over the specimens at 730°C. The specimens were then homogenized at 730°C for 2 hr in dry hydrogen. After the carburizing treatment the specimens were given the same vacuum anneal as for the decarburized specimens. The carbon content was determined from the maximum value of the internal friction carbon peak.2 Apparatus Fig. 1 shows a diagram of the tensile apparatus, with half the cooling coil removed. The cooling coil enabled temperatures from 200" to 77.2oK to be obtained. The apparatus was designed to fit a standard Tinius Olsen Universal tensile machine. The apparatus consisted of the rigid plate A which carried two carefully machined hooks H. These hooks attached the plate firmly to the moving crosshead of the tensile machine. The lower grip B was rigidly suspended from the plate A by three stainless steel rods. The upper grip C was joined to the upper grip of the tensile machine by the stainless steel rod E. The lower part of the apparatus was surrounded by a Dewar vessel, which was made a sliding fit inside the brass collar D. The specimen was held in a clamp which fitted into the grip, forming a ball and socket joint (see inset a). This was to attain as nearly pure

Jan 1, 1954

By Norman L. Newbern, Robert E. Green

An investigation of the effect of size on the deformation properties of metal single crystals made it desirable to grow from the melt cylindrical aluminum single crystals possessing exactly the same crystallographic orientation but varying in diameter. Methods for the growth of rather large (up to 3 in. diam) aluminum single crystals in molds of the desired shape are well known. However, when one applies the same techniques to the growth of smaller (less than 1/8-in. diam) specimens many additional problems arise. Two of the major problems are the construction of the molds to be used and the removal of the thin specimens from these molds without deformation after growth has been completed. Also the problem of the constraint forces exerted by the mold on the specimen is much more pronounced for the smaller specimens. The technique described herein is a zone-melting method in which no mold is used since the surface tension of the molten metal and its oxide is sufficient to retain the melt. The specimen is suspended vertically in a manner similar to that of Keck and Golay.2 However, while Keck and Golay supported the specimen from both ends, the method used here supports the specimen only at the upper end. The surface tension of the molten aluminum and aluminum oxide contains the melt and suspends a length of newly grown crystal that has already passed through the molten zone until the weight of the newly grown crystal is equal to the component of surface tension holding the specimen together in the molten region. When the weight of the newly grown crystal is equal to the component of surface tension holding the specimen together the specimen pulls in two in the molten zone. The length of crystal which can be grown before this separation occurs varies with the diameter of the specimen and the size of the molten zone. In order to prevent the specimen from pulling in two a tube of glycerine is placed beneath the furnace in such a manner that the newly grown crystal passes into the glycerine which provides sufficient buoyancy to allow aluminum single crystals in wire form to be grown to lengths determined only by the length of the tube containing the glycerine. A schematic diagram of the experimental arrangement is shown in Fig. 1. The furnace used is constructed as follows. High-resistance nichrome wire is coiled on a 3/8-in. diam fused quartz tube. The distance between the windings is much less over a length of about 3/8 in. at the center so as to develop a hot spot. This core is located in the center of a 4-in. diam steel cylinder 5 in. in height and insulated from it by Kayolite. The temperature of the furnace is controlled by means of a thermocouple located near the central hot spot and a Minneapolis-Honeywell temperature controller. Temperature ins,ide the furnace is measured with a thermocouple and a standard potentiometer in the usual manner. By the above method it is possible to grow high-purity (99.99 pct Al) aluminum single-crystal wires over a range of sizes. Crystals varying from 1/8 to 1/64-in. diam were grown by the authors. Since the tube containing the glycerine cannot contain a crystal longer than approximately 3 ft, the growth of crystals longer than this presents another problem. It was found that one could cut the newly grown crystal without deformation in the region between furnace and glycerine tube try means of a cutting torch and then by moving the glycerine tube slightly aside continue

Jan 1, 1962

By J. W. Rutter, K. T. Aust

THE object of the experiments to be described in this report was to determine, first, which grains, out of a large number introduced into a sample in which their growth could proceed, were able to grow most successfully; and, second, the factors which control their growth selection. In an earlier study of grain boundary migration in high-purity lead,' it was found that, under some conditions, the most successful grain in an experiment of this type bears a special orientation relationship to the grain into which it is growing. The present work represents an extension of the previous study, directed at the determination of the orientation relationships which appear under a wider variety of conditions. Experiments of this general type have been done using commercial aluminum2 with somewhat conflicting results. In the present experiments, in contrast to the above,' the sample composition was a principal controlled variable, resulting in a considerable clarification of the phenomena observed. EXPERIMENTAL TECHNIQUE The experimental technique used in this investigation was essentially that employed previously in studies of grain boundary migration kinetics.1'3 The material used was zone-refined lead with various small amounts of tin or silver added to study the effect of varying the sample composition. The specimens were in the form of single crystals, about 1/4 in. 1/4 in cross section by 3 to 4 in. in length, grown from the melt in a horizontal graphite boat. A crystal grown in this way generally contained a lineage or "striation" substructure of the type shown in Fig. 1 of Ref. 1. This substructure consists of an array of low-angle boundaries which partition the crystal into regions misoriented from each other by a few degrees. The substructure constitutes a source of driving energy, estimated to be about 4000 ergs per cc, for the migration of a large-angle grain boundary into the striated crystal. New grains were introduced by plastic deformation in compression of a localized reglon at one end of the sample. Re-crystallization occurs at room temperature in the deformed region, introducing a large number of new, striation-free grains into the specimen. These grains are able to grow into the melt-grown crystal on annealing at a suitable temperature. The stria-tions are removed by passage of the grain boundary, as the substructure energy is utilized to produce the boundary migration. Usually, only one or two of the recrystallized grains persist after growth has occurred for about 1 cm out of the deformed region. Laue back-reflection X-ray photographs were obtained to determine the orientation relationship between the melt-grown crystal and the recrystallized grain or grains which grew most successfully in each specimen. EXPERIMENTAL OBSERVATIONS Fig. 1 shows the results obtained for a series of specimens to which had been added tin in the range from 0 to 5 ppm by weight. In this figure is plotted, in the standard stereographic triangle, the single axis about which the most successful recrystallized grain or grains are related to the starting, melt-grown crystal by the smallest rotation. The range of angular rotations observed about such axes is indicated beside each stereographic triangle. The results shown in the stereographic triangle on the left, Fig. l(a), were obtained by localized deformation at one end of each specimen at room temperature, followed by annealing in a furnace which had been preheated to 300°C. The furnace atmosphere was argon. It will be seen that the orientation relationships observed between the melt-grown and recrystallized grains are quite random. On the right, Fig. l(b), are shown results for samples in which the de-

Jan 1, 1961

By Luiz C. Correa da Silva, Robert F. Mehl

A. D. Le Claire and R. S. Barnes (Atomic Energy Research Establishment, Harwell, Didcot, Berks., England)-—This much awaited paper admirably confirms that the Kirkendall effect is a true diffusion phenomenon and likely to be found in all diffusing systems. The most likely explanation put forward so far to account for the shift of interface is that the two components of the system, diffusing in opposite directions, do so with unequal rates so that there is a net loss of material from that half of the diffusion zone rich in the more rapidly diffusing component. This loss is accompanied, and at least partly compensated for, by a closing up or decrease in volume of this latter half of the diffusion zone and an expansion of the other half so as to tend to keep constant the overall volume per atom. This is manifest as a movement of the original interface. If this is a true picture of what is taking place then there are at least two important matters requiring further study."1—The quantitative relating of the observed shift with the independently measured separate diffusion coefficients of the two diffusing species."2—A detailed study of the mechanism and characteristics of the closing up process."We would like first to make a few remarks pertinent to these topics. In connection with the first of these, it is a pity that more and detailed measurements were not made on the Au-Ag system, the only one for which the separate diffusion coefficients of the two species have been measured.'" One of us (A. D. Le C.) has calculated from Johnson's results the shift to have been expected in samples D.2 and D.3. Darken4 showed that the velocity v with which the markers move is related to the separate diffusion coefficients Dau, Dag, by the eauation:"dN"v = (Dag — Dau "dx"dN"where .is the concentration gradient at the mark-ax"ers. Under certain conditions,4, 20 it can also be shown that:"Xm"v = "2t"where x, is the total marker shift after time, t:"dN". . xm = 2t (Dag — Dau) [9]"dX"Johnson measured Dag and DAu in a chemically homogeneous alloy and so his reported figures represent the true or ideal diffusion coefficients"; the same quantities in eq 9 represent the actual diffusion coefficients as would be measured in the presence of a chemical concentration gradient, so we need to multiply Johnson's reported values of Dag and Dau by the"1 before insert-dlogN "ing them in eq 9. 7 is the activity coefficient of Ag at the concentration prevailing near the markers which we shall assume to be - 50 pct. The values of the thermodynamic factor for N = 0.5 and the temperatures at which D.2 and D.3 were annealed were obtained from thermodynamic data quoted by Darken.' aN/ax was computed from the coefficient of inter-diffusion of Au and Ag given by Johnson on the assumption that in the samples D.2 and D.3, the concentration distance curve could be represented by the standard equation:""No is the original difference in concentration between the two halves of the couple, and + is the error or probability function."aN/ax at x = 0 is then given by:"adN/dx "2/nDt"and we assume that this represents the concentration gradient at the markers, although it is probable that the figure is slightly high."When all the appropriate quantities are inserted in eq 9, we find that the expected shifts are: for D.2, 0.0134 cm and for D.3, 0.0119 cm."The agreement between these results and those

Jan 1, 1952

By H. C. Vacher, C. J. Newton

EXTENSIVE investigations in the field of residual strain measurement by X-ray diffraction have been made by Bollenrath, Hauk, and Osswald,1 by Smith and Wood,2'3 by Greenough; by Rosenthal and Norton." and many others. Since X-ray strain measuremeits apply only to those crystals of the test body which are of the proper condition and orientation to diffract and since the residual strains revealed may be accompanied by either body or tex-tural stresses, there has been considerable disagreement among investigators with respect to the validity of conclusions in this field. Although the experi-mentors have employed a variety of loading schemes, surface preparations, and X-ray wave lengths, the observations almost invariably have been made only on the outer surfaces of the specimens. The present note is not to be construed as an exposition of a new method of stress analysis by X-ray strain measurements on sections but as a presentation of some results which point to interesting possibilities for further experiments with sections. The two test rods used in this study were of ingot iron annealed at 910°C. The initial length of the gage section was 2 in. and the diameter was 0.415 in. Cross-sections were cut from the ends of the annealed rods to provide strain-free material. The tensile rod was axially loaded the desired amount in a commercial testing machine. A 1 in. portion of the gage length was cut from the other rod and was subjected to compression in the same machine. Details of this plastic straining of each rod are given in the upper half of Table I. A half-cylinder piece about 1/4 in. long was obtained by making a short longitudinal plane cut containing the axis of the rod near the center of the gage length. From adjacent material a disk about 1/8 in. thick was cut to provide the cross-section specimen. Later another section was cut from this same region with an angle of 30" between the normal to its surface and the axis of the test rod. A cross-section and a longitudinal section were cut from the compression rod in a similar manner. All of these as well as the strain-free cross-sections were mounted in Bakelite and used as specimens for the following X-ray strain measurements. During the course of the study, it became apparent that the condition of the surface of a specimen was a highly critical factor. One of the annealed strain-free specimens as a control was subjected to about 24 hr of polishing with fine alumina, interrupted about every 2 hr for etching with 1 pct nital. Its lattice parameter was determined at intervals from measurements on back-reflection X-ray diffraction patterns, which were calibrated with diffraction from tungsten powder. The parameter gradually approached the value found in the literature for strain-free iron and remained there, within the limits of the experimental error. This determined a long polishing and etching procedure which was adopted for all the specimens and which gave X-ray results from the surfaces believed to be representative of each specimen as a whole. A large number of back-reflection patterns were made with cobalt and chromium radiation, all at normal incidence. Except for some preliminary stationary exposures made to monitor the removal of cold work from the surfaces, each exposure was made with the specimen slowly translating and the film slowly rotating. In appropriate cases a thin layer of a standard metal powder, tungsten with cobalt radiation and silver with chromium, was dusted over a film of vaseline on the surface of the specimen to serve to calibrate the X-ray patterns. After the preliminary work, four films were made,

Jan 1, 1956

By H. C. H. Darley

Particles of montmorillonite-type clays consist of plate-like clay crystals stacked face to face. Under certain conditions in a suspension, these particles disperse to individual platelets with the formation of diffuse double layers round each platelet. This action has a profound influence on the rheo-logical and other properties of the suspension. This paper describes a test for degree of dispersion and uses this test to correlate changes in dispersion with changes in viscosity and gel strength. The test is of practical value in determining and controlling dispersion in drilling muds. INTRODUCTION It has long been recognized that the hydration and dispersion of clays, particularly those of the montmoril-loilite type, strongly influences the rheological and other properties of drilling muds, but little has been done to measure either of these phenomena under conditions that exist in drilling muds. The hydration of clays as such has been extensively studied by those interested in clay mineralogy, but in drilling muds it is to be expected that dispersion is at least as important a factor as hydration because of the much higher water-to-clay ratios and the very high degree of mechanical agitation. The term dispersion as generally applied to colloidal systems means the subdivision of large particles to small. Particles of montmorillonitic clays, however, consist of plate-like particles stacked face to face. Dispersion of these aggregates to individual platelets may be expected to have an unusually large influence on the properties of the suspension because of the shape factor, the enormous increase in specific surface, and the pronounced surface phenomena exhibited by the crystal surfaces. It is this form of dispersion that is particularly considered in this paper, -and the term degree of dispersion is used to imply the number of platelets per particle. The term aggregation is used to denote the opposite of dispersion, the association of individual platelets face to face to form stacks. It is important, as Garrison' has pointed out, to distinguish between the deflocculation-flocculation phenomenon and the dispersion-aggregation phenomenon. Flocculation of clay suspensions is characterized by the formation of voluminous sediments that are stable under quite high centrifugal fields. This indicates an edge to plate association of particles to form an open network type of structure, which obviously will have quite a different influence on the properties of the suspension than aggregation of the platelets face to face. The work described in this paper was primarily concerned with developing a test for degree of dispersion in clay suspensions and by means of this test to follow changes of dispersion brought about by addition of electrolytes and to show the influence of dispersion on the rheological properties. The Clay-Volume Test This test is based on the assumption that the greater the number of particles per unit weight of clay in a suspension the greater will be the volume of sediment when it is flocculated under standard conditions and centrifuged. After considerable experimentation the following procedure was established: 1 cc of the test mud vigorously shaken with 100 cc of 1-N NaCl in an ASTM oil centrifuge tube and centrifuged for five minutes in an International No. 2 centrifuge at 2,000 rpm. When drilling fluids of different solids content are being compared, the clay volume is expressed in cc per gram of clay solids, but generally changes in dispersion in a given mud are being compared and it is more convenient to report as cc of sediment. The test is strictly a comparative test, so that it is not necessary to adhere to the conditions specified above, e.g., with field muds a stronger flocculant such as Al2(SO4)3 may be preferable to NaCl.

Jan 1, 1958

By J. B. Macelwane

Historically whenever application of scientific results to a new problem required the special experimental background, the economic outlook and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering based on the professional requirement grew up in the engineering colleges. This is precisely what is happening now in geophysical engineering. THE Mineral Industry Education Division of AIME has long been interested in geophysical education. Organized in 1938, a Committee on Geophysical Education presented a number of reports in succeeding years. The AIME is an engineering society; hence it might be expected that the interest of the Mineral Industry Education Division would have centered about the relation of courses in geophysics to engineering education. However, this was not the case. The burden of the discussion held under the auspices of the Committee on Geophysical Education bore on geophysics in general and particularly on its relation to geology. In the decade that has passed since those meetings much water has flowed under the bridge. Not only have the geophysical sciences developed at an extraordinarily rapid rate but the practical importance and the range of their applications have spread in ever widening circles and have even assumed a very prominent place in research programs of the military, the Army, the Navy and, particularly, the Geophysical Research Directorate of the Air Force at Cambridge, Mass. So enormously have the geophysical sciences as such grown in scope and in degree of specialization that no one man in a lifetime of study can hope to master the theoretical and experimental complexities or even to follow intelligently in the published literature all the varied accomplishments of basic research in these fields. As in the other sciences, most of the results of geophysical research have potential economic value and are being applied to a wider and wider range of human needs. Here we see a parallel with the older sciences and their relation to engineering. Whenever the applications of scientific results required the special experimental background, the economic outlook, and the practical knowledge characteristic of the engineer, a curriculum in that type of engineering grew up in the colleges and universities. In the words of the "Report of the Committee on Adequacy and Standards of Engineering Education" in the January 1952 number of the Journal of Engineering Education: "Engineering education in America was not developed after a preconceived plan. It evolved in parallel with the needs of a growing country, a country engaged in the development of a vast industrialization. From the first it filled a practical need, and its design emanated largely from an evaluation of the professional requirement." The advent of the railroad created a need for scientifically trained engineers and the response was the curriculum in civil engineering. The development of steam power created the demand for a curriculum in mechanical engineering. Neither of these types of engineers was trained to cope with the requirements of electrical power, and so there came to be a curriculum in electrical engineering. The advent of radio communication and of electronics during the first World War and in the years that followed resulted in the establishment of electronics engineering, sometimes within the curriculum in electrical engineering and sometimes independent of it. The complexities of industrial management have created an ever increasing demand for industrial engineers and the consequent building up of a curriculum in industrial engineering. The wide industrial application of chemical processes required a type of engineer whose background was training in chemistry but who was able to design processes and plants on an industrial scale; hence we have the curriculum in chemical engineering. The advent of the airplane created an entirely new set of problems which were solved by the training of aeronautical engineers. Many of these have called for more and more science and mathematics. Such was the history of the older engineer-

Jan 1, 1953

PRESIDENT MARKS: We have a letter from Mr. Frank N. Cameron, of the Utah Fuel Company, that perhaps I had better read to you. It is addressed to Mr. Shubart, Rocky Mountain Coal Mining Institute (hands letter to Secretary Shubart). UTAH FUEL COMPANY MINE SUPERINTENDENT Castle Gate, Utah, February 9, 1926 Mr. F. N. Cameron, Vice-President & General Manager, Salt Lake City, Utah. Dear Sir: It has now been about nine months since we started the system of having the fire bosses take charge of all shooting and gas inspections at the Castle Gate Mines. We had considerable trouble when we started. Like all other new systems which have been installed, this one was hard to get started and was criticised both by the miners and officials in our own organization, as well as by other organizations in the mines of this county. The older the official and miner was the stronger they seemed to be opposed to the new method. They have no arguments to offer against it, but they know it is not right "because their grandfather did not work it in that way." We know that when some of the other systems were started in the mines of this county, they were fought from all angles. The electrical shooting almost brought the miners at Sunnyside out on strike; their main argument was that they could not make a living if they had to obey the rules that the company was trying to enforce. They also claimed that they could not make enough coal for the day's work by only shooting once at the end of the shift. The same applies to the sprinkling the miners claimed that they would all die of some disease if they were forced to work in a sloppy, wet mine every day. The mining machine was another thing that was hard to install the miners claimed that the company was trying to rob the Door miner out of a chance to make living by installing mining machines to cut the coal. I do not think that the system we have at our mines is perfect-there is still room for improvement in the shooting and inspection of the mines, but I do really think that for safety and efficiency, the inspection department at our mines, working under the new system, is as good if not better than any other inspection department working under the old method in the other mines. I am giving some of the arguments in favor of the new system and would like to hear the arguments against it-if there are any. In cutting the men from monthly to day wages, I do not think it is only the company that benefits by the arrangement, but the fireboss is the one that gets the best of it by the change. How often have we heard the fireboss complain of the hours he had to put in just because he was a monthly man? Under the new wage scale he is paid for every hour he puts in the mines, and when the mines are working every day he makes considerable more than when he was being paid a monthly salary. When the mines are working slow, there is generally some work that has to be done on idle days, or in slow times the force could be cut to a point where some of the work could be done on idle days, and thus the fireboss could be given the preference in this extra work and in this way, his wage could be kept up to the standard monthly salary he was getting before. Under this arrange-

Jan 1, 1926

By Robert W. Buechley, Charles R. Key, Jonathan M. Samet, Marion V. Morgan, Arnolfo A. Valdivia

INTRODUCTION The Uranium Epidemiology Study at the University of New Mexico was initiated in 1977 with the objective of assessing health effects of uranium mining in the Grants, New Mexico, area. The planned approach was a cohort study of mortality that would capitalize on the availability of health records at the Grants Clinic. During the first year, emphasis was placed on determining the feasibility of the proposed study: Were adequate records available? What was the quality of available information? Could a cohort be established? The first year's work confirmed the study's feasibility (Buechley, 1979). Subsequent efforts have focused on the health and exposure data base and comprehensive follow-up. A retrospective cohort study of early miners is in progress; a prospective cohort study of miners who began working under the current Federal standard is planned. This report will summarize the current status of the Uranium Epidemiology Study. A chronology of the study's activities follows (Table 1). TABLE 1. Uranium Epidemiology Study Timetable 12/77 Official start of study. 12/77-8/78 Abstracted Grants Clinic records of 21,780 persons examined for mining companies from 7/57 through 12/76. Checked company personnel records to establish who had worked underground 1 year or more through 12/76. 7/78- Obtained physical exam and mining history information on qualified miners from Grants Clinic and companies. 9/78- Obtained working level month information from companies and other sources. 12/78- Checked qualified miners list with New Mexico death tapes and New Mexico Tumor Registry files. 9/80- Submitted qualified miners list to Social Security Administration for search of its records. 12/80- Obtained copies or abstracts of early State Health Department and Mine Inspector's reports. 3/81-4/81 Conducted Pilot Respiratory Disease Survey. 3/81- Verified underground status of qualified miners via company personnel records. 3/81- Verified smoking and mining histories of qualified miners via Grants Clinic records. 3/81- Began establishing cohort with first underground experience after 1970. 4/81- Checked qualified miners list with Post Office, Voter Registration Office, Motor Vehicle Division, telephone directories, city directories, and other sources. BACKGROUND Uranium Mining in New Mexico The Grants, New Mexico, uranium belt measures some 110 by 25 miles in Cibola, McKinley, and Sandoval counties (Kelley, 1963). The three chief mining districts are, from east to west, Laguna, Grants, and Gallup. Average annual production was about 5,500 tons, or 45% of United States uranium, from 1966 through 1978. Despite a drop in this figure in 1979, to 40%, New Mexico still leads the nation in uranium reserves and production (Hatchell, 1981). In 1918 carnotite, a yellow uranium vanadate, was identified in the Shiprock area (Chenoweth and Learned, 1980; N.M. Energy and Minerals Department, 1981). It received little attention at the time because of its apparently limited volume. In 1950 an important uranium outcropping was discovered by chance in limestone at Haystack Butte, northwest of Grants. In 1951 deposits were discovered in sandstone at Poison Canyon, north of Grants, and at Jackpile, northeast of Laguna. In 1955 finding of radioactive cuttings at an abandoned oil test site near Ambrosia Lake led to drilling and discovery of the first underground deposits (Melancon, 1963). Ore bodies were also found near Church Rock in the 1950's (Rautman, 1977). A uranium rush followed. At various times during 1952-1962, 60 mines and 5 mills were in operation (Gay, 1963). In the early 1960's the price of uranium fell, and many miners left the area. Subsequent market fluctuations have produced shutdowns and consolidations, development and expansion. Many early uranium miners came to New Mexico with

Jan 1, 1981

By Howard E. McKinney

A high-pressure wellhead lubricator has been developed to facilitate telemetering electrical measurements from subsurface reservoirs to the surface with the well under normal flowing conditions. The field unit in use at the present time employs a 5/16-in diameter, single-conductor armored cable and is to be used in wells with surface pressures up to 5,000 psi. It has a pressure sealing element that maintains a continuous and absolute seal around the cable as it enters or leaves the tubing at speeds up to 175 ft per minute. A cable injecting device is used which obviates sinker bars or weight sections on the instrument. INTRODUCTION The development of instruments for securing physical measurements in pressure wells has been confined in the past to those instrument which would operate on a wire line and record the necessary measurements in the downhole instrument itself, or those which would operate on an electric cable in a well with the surface pressure killed by the use of weighted fluids or by the use of tubing plugs. In one case the accuracy of the measurements is questionable, and in the other the range of application is very limited. Considerable work has been done by other interests to provide effective means to accomplish the necessary telemetering. The U. S. Bureau of Mines developed a wellhead lubricator prior to 1947 which permitted a 5/16-in diameter single-conductor cable to be lowered into a well with a surface pressure of approximately 500 psi. This unit was used successfully in a number of tests in Oklahoma. A company which tests wells has recently offered on a service basis a wellhead lubricator with a 3/16-in diameter cable that reportedly operates up to 2,500 psi surface pressures. Each of the above operates on a staging principle to effect a seal. In both of these units some leakage of well fluid occurs when the cable is moved. SPECIFICATIONS FOR DESIGN In order to provide the maximum flexibility in its use, the following parameters were established for the design of our high-pressure wellhead lubricator: L An absolute well fluid seal up to 5,000 psi surface pressures. 2. Means for raising and lowering the instrument at speeds of at least 100 ft per minute. 3. Provision for the instrument to enter and leave the well without disturbing the well flow or the reservoir conditions. 4. A cable large enough to provide suitable electrical characteristics and suitable mechanical properties. 5. A method of operation that will not damage the well in any way. The present high-pressure wellhead lubricator field unit fulfills the above requirements. DESCRIPTION OF THE UNIT AND ITS OPERATION The cable selected for this use is the standard Amergraph 1H2 as manufactured by the American Steel and Wire Co. This particular cable is normally used by the Halliburton Oil Well Cementing Co. in their conventional well logging operations. Although the cable presents a noncircular cross-section (Fig. l), its diameter is very consistent; lor example, maximum diameter is 0.325 in., minimum diameter 0.314 in. This [actor permits the use of the sealing element, as later described. Early in the development of the high-pressure wellhead lubricator it was apparent that we could not effect a direct gas seal around a moving 1H2 cable. This becomes evident when an examination of the cable cross-section is made. The voids between the strands of the outer armor provide natural channels lor the flow and escape in large quantities of a low-viscosity fluid such as gas. However, it is relatively simple to

Jan 1, 1952

By B. Pesic, J. E. Wey

Introduction One important class of manganiferrous ores is manganiferrous-silver ores. They occur in the oxidized portions of the silver deposits of the western United States. Silver is often associated with manganese oxides, which in some ore deposits are dispersed through calcite, causing the black color of the host rock, known as black calcite. Black calcites can occur in carbonate rocks (0.3 to 50 kg Ag/t) and in volcanic rocks (less than 30 g Ag/t). Silver mineralization associated with manganese oxides and black calcites can occur in veins (Hewett, 1968) or as disseminations (Graybeal, 1981). In the US, silver-bearing manganese veins are located in a broad arc that extends from southern Colorado to southwest New Mexico, southern Arizona, and southeast Califor¬nia (Hewett, 1964). Areas of disseminated silver-manganese mineralization include the Creede and Silver Cliff districts of Colorado and the Tombstone and Hardshell districts of Arizona (Graybeal, 1981). These deposits are also characterized by significant amounts of silver halides - cerargyrite (AgCl), bromargyrite (AgBr), and iodargyrite (AgI). Black calcites are also common in these deposits. Oxidized silver ores containing the higher oxides of manganese are generally refractory to hydrometallurgical methods of treatment. In the past when these ores could not be smelted, they were treated generally by cyanidation at very low efficiency. The US Bureau of Mines (USBM) studied the problem of treating silver-manganese ores in the early 1920s (Clevenger and Caron, 1925). It was found that the refractory silver in the original ore was insoluble in all the common solvents for metallic silver and its salts. The conclusion was that to obtain the highest recovery of silver, all the manganese had to be dissolved or the higher oxides of manganese reduced to manganous oxide. More recent results from treating refractory silver¬manganese ores were given by USBM (Scheiner et al., 1973). The silver ores from Candeleria District, NV, and Round Mountain District, CO, were investigated. Electrooxidation experiments recovered only 34% silver with minor amounts of manganese dissolved. Sulfurous acid pretreatment followed by cyanidation revealed that silver extracted was proportional to the amount of SO2 used. A similar approach, using sulfurous acid pretreatment followed by cyanidation, was also proposed by Rhoades et al. (1984). Hazen Research Inc. performed extensive testing on silver and manganese dissolutions from Ag-Mn ores obtained from the Candeleria and Round Mountain ore deposits. The methods examined were direct cyanidation, pretreatment with sulfurous acid followed by cyanidation, malonitrile leach, and leaching with ammonium hydroxide-sodium thiosulfate under slight oxygen pressure. The results were not satisfactory. The importance of the vast reserves of Ag-Mn ores and the lack of an efficient method to recover these metals warranted a search for new technologies. One novel method for extraction of these metals is treatment of Ag-Mn ores with acidified thiourea solutions. Preliminary results of the leaching of silver and manganese from Ag-Mn ores were very encouraging (Pesic, 1984a) ; thus, it was decided to examine the new lixiviant in more detail. Experimental Ore from the Round Mountain District was studied. It was crushed, ground, and dry sieved into monosized fractions in the range of 16 to +400 mesh. The ore composition was about 90 g Ag/t and 3% Mn, depending slightly on size. The leaching experiments were performed in apparatus described elsewhere (Pesic, 1982 and 1984b). All experiments were performed at constant temperature conditions. The leaching residues were analyzed for silver and manganese. Atomic adsorption was used to analyze the solution samples and fire assaying to analyze the leaching residues (for silver). The standard experimental conditions are given in

Jan 1, 1987

By Albert Hofstra, Joel Leventhal

The gray, dark gray and black colors of the sediments and the presence of pyrite in the Carlin, Jerritt Canyon, Horse Canyon, Betze, and Gold Acres sediment-hosted disseminated gold (SHDG) deposits indicate that these rocks are not oxidized with respect to carbon and iron sulfide. Both ore and non-ore host rocks generally are dark colored. Analyses for noncarbonate carbon (usually called organic carbon) in samples from SHDG deposits and related unmineralized rocks indicate that these rocks contain from a few tenths to a few percent carbon. We use the term noncarbonate carbon because, strictly speaking, organic carbon denotes carbon that is bound to hydrogen. However, the carbon present in SHDG deposits and related rocks has very little hydrogen chemically bound to it. Rocks with less than 2% organic carbon are usually gray in color. The dark colors in our samples are due to the relatively high temperatures that these rocks have experienced relative to organic matter maturation. We confirm the results of Nelson et al. (1982) that previous reports (for example, Radtke and Scheiner, 1970) were incorrect in reporting significant amounts of humic acids, extractable hydrocarbons (bitumen) or "carbonaceous" material. We believe these reports had problems with contamination or misdirected emphasis. Our samples consisted of unweathered rocks, collected mainly from mine cuts (benches, trenches, cores) and put into glass containers or wrapped in aluminum foil to avoid contamination. Only a few samples were collected from natural outcrops. We were careful to avoid samples in proximity to blast holes that were packed with ammonium nitrate and diesel fuel ("ANFO"). Contamination by ANFO may explain some of the previous reports of hydrocarbons, pyrobitumens, humic acids and anomalous nitrogen. When we were collecting samples, it was apparent that in addition to lithologic and color differences, the surface appearance of the rocks was distinguishable: "preg robbing" material that had a sooty surface; "graphitic" rock with a shiny surface; and more ordinary rocks that had a flat gray or black appearance. [Preg robbing is a term for ores that adsorb gold from the milling circuit; the graphitic material had not been x-rayed to actually identify graphite.] We hoped that laboratory study of these samples would show some fundamental differences that we could relate to ore genesis. Even though these sample types appeared different in the field, we could not distinguish any differences in thermal maturity (see below). Normal petroleum/organic geochemical laboratory procedures (solvent extraction, Rock-eval, pyrolysis-gas chromatography) failed to yield much information because the carbon was over-mature relative to oil and gas generation. Rock-eval results show less than 20 (± 20) mg of pyrolizable hydrocarbons per gram organic carbon (and an indeterminate Tmax) indicating that the organic matter in these deposits is burned-out relative to petroleum generation [with an H/C (atomic) ratio of less than 0.41. Because of the non-definitive results from standard organic geochemical methods, x-ray diffraction (XRD) and Raman spectroscopy were used to characterize the carbon. Prior to XRD, samples were treated with HCl and HF acids (1) to remove quartz that has a peak near 26° [20] at the position of the 002 peak of graphite and (2) to concentrate the carbon to a level detectable by XRD. The residue was put on a colodion mount and analyzed by XRD. The XRD analyses yielded a broad peak at 26° [20]. The shape of this peak indicates that the carbon is more thermally mature than anthracite rank coal but less mature than crystallized graphite. Based on XRD results from the literature (Landis, 1971) that are calibrated to metamorphic facies, results from our samples correspond to pumpellyite-actinolite to lowermost greenschist facies conditions, probably

Jan 1, 1990

By W. D. Haentjens, A. P. Pipilen, M. Weintraub, A. A. Orning

W. D. Haentjens (Barrett, Haentjens and Co., Hazleton, Pa.) — The authors are to be complimented on undertaking a project which has little available experimental data. There are so many variables in the hydraulic transport of solid materials that it is difficult to correlate the experimental information from one series of tests into usable data involving other materials or even similar materials but of different size consists. The friction data is of particular interest to those involved in pipeline design. Most such pipelines, however, involve portions which are not level and the effect of sloping or vertical lines might also be considered in extensions of this test work. Pump manufacturers are concerned about criticism resulting from the stated amount of degradation occurring in a pump. The amount of degradation is affected somewhat by pump design and this should be taken into consideration. The pump which was loaned for this work was a modification of a standard medium duty slurry pump. This modification was for maximum particle size, however if minimum degradation is the object, then other design changes would be indicated. Although there is a tendency to be less concerned with degradation in industrial applications, it is nevertheless an important factor in many uses and further studies should be made. In particular, the amount of degradation could possibly be segregated into more classifications, rather than charge some losses to the pump which apparently are occurring in other handling. It seems difficult to evaluate the degradation which occurs in handling the coal into the pump sump and in removing it from the line into the tank. Each handling, of course, contributes some degradation, as does the screening operation itself. These are all charged to the pump, or to the pipe line and pump together; and, although they may be small, they could possibly be evaluated. It is interesting to note the verification of the old rule of thumb of maximum particle size equal to approximately one-third of the pipe size. Our experience has shown size distribution to have an effect on the flow characteristics and if this data is available for the tests which were run, it would be interesting supplementary information. A. P. Pipilen, M. Weintraub and A. A. Orning (Authors' Reply) — In this paper the authors have attempted to outline some of the major factors affecting a rational design for a solids-liquid transport system. They are grateful to Mr. Haentjens for pointing out several other equally important considerations. Pump manufacturers, in general, should be complimented on the strides that have been made in decreasing particle degradation within the pump. Considerable research and a great deal of mathematical analysis is required before pump design in this field can become a science rather than an art, for each system requires a different set of compromises. As Mr. Haentjens indicates, maximum-particle-size handling capability may be inconsistent with minimum degradation; even more important, the rotor profile for the most efficient transfer of energy to the fluid may have to be compromised to reduce particle breakage, for, whenever particle density differs from fluid density, the two phases will have different trajectories. Some evidence of this geometric factor is provided by a cursoy analysis in the Bureau of Mines Report of Investigations now in preparation, where it is indicated that, for the pump used, degradation decreased when the tangential velocity was decreased and when the radial velocity was increased. This relation, itself, is probably a function of particle size and concentration. Some data on particle size distribution, as requested by Mr. Haentjens, will be provided in the Report of Investigations referred to above in addition to that already presented in Table II of the original paper. However, in the limited number of tests it is difficult to distinguish between cause and effect, for not only did the particle size distribution alter the flow characteristics, but, through the medium of degradation, the operating conditions rapidly altered the particle size distribution.

Jan 1, 1965

By Thomas J. Neil, O&apos

Most analysts find that progress has been evolutionary in any technologic field. To be sure, a few discrete breakthroughs can usually be identified, but viewed in its entirety, the curve of technologic progress over time tends to be relatively smooth with few discontinuities. Even in those cases where a major scientific discovery is achieved, the rate of technologic progress is limited by the often surprisingly slow rate of commercializing the concept into usable products. Whereas discovery and invention tend to be discrete events, technical innovation is often a painfully slow process. In spite of overall gradual change, technologic progress in most fields, when viewed in retrospect, tends to reveal certain relatively homogeneous periods where little change is evident, separated by episodes of accelerated progress. Thus, open-pit mining over the past century has changed from predominately train haulage to truck haulage and is now experiencing a major increase in belt haulage. Ore reserve estimation is another field that fits the same pattern, and the history of mine evaluation lends itself to a similar analysis. Evaluating mine investment opportunities is a fascinating aspect of mining. The unique set of risks inherent to every mining project is particularly intriguing. Geologic risks are most obvious, since faulty ore grade and tonnage estimates are among the leading causes of mine failures. Wide swine's in mineral commodity prices are usually cited as another major risk in mining. Because any ore deposit is a finite resource and the miner has limited discretion in selecting a mining sequence, mines are generally at the mercy of notoriously fickle commodity markets. There is a tendency for many mine investment analysts to feel that mineral market uncertainties are unprecedented in severity. Of course, prices in other markets rise and fall also-in some cases as precipitously as with minerals. However, two other mining characteristics tend to compound this marketing risk. First, the preproduction development period for a new mine is characteristically long. Under extremely favorable conditions, a significant mine may be developed in as little as two years, but the norm is four to six years or more. Second, mining is among the most capital intensive industries, consistently ranking near the top among all industrial sectors in assets per employee, and near the bottom in annual sales dollars per dollar of assets. Thus, mine investors typically have large sums invested for a long time before the outcome of the venture is determined by notoriously unpredictable markets. This is not a business for the faint of heart, and the importance of sound investment decision making is obvious. The high risk and technical complexity of mining operations have combined to require greater attention to financial evaluation by mining engineers than by most engineers in other specialties. Nearly all early mining engineering textbooks dealt with problems in mine valuation in a detailed manner; and, today, the sophistication of capital investment analysis is high in the mineral industries. Traditional Mine Valuation Methods Although some evaluation process has no doubt accompanied nearly every mine development throughout history, a formalized quantitative approach first emerged in the last half of the 19th century with the establishment of academic programs in mining engineering. The philosophy and approach to mine valuation that evolved at this time were, with periodic minor refinements, considered the standard for nearly a century. Only after 1960 did major changes begin to occur. The traditional approach to mine valuation reflected the investment community's historic attitudes toward risk. Mines were generally considered too risky for debt financing, and virtually every new mine was financed from internally generated funds or new equity subscriptions. The investment evaluation methods that evolved focused on mining's higher risk relative to other

Jan 11, 1982

By Joseph L. Walker

INTRODUCTION In looking over the diversity of the papers that are being presented during this meeting on The Industrial Practice of Fine Coal Processing one cannot help but be impressed with the progress the industry has made in beneficiating fine raw coals, and in the number of innovations that are under study to increase recovery and to improve the quality of the finest size particles produced at a preparation plant. Those who are not in our industry, who look at the technical program, might be confused, when they see that the papers include such topics as cleaning to zero and heavy media cyclone cleaning 28M x 100M; application and performance of fine coal jigs, tables, hydrocyclones, spirals, and flotation; filtration, dewatering and thermal drying; and ancilliary aspects such as fines handling, instrumentation and process control plus screening and liberation. This is an observation and not a criticism of the diversity of papers being presented. The program fits within the parameters of fine coal preparation as the term "coal preparation" is defined, but perhaps not as the term "fine coal" is defined. Admittedly these definitions are sometimes loose. However, each should be made more definitive if a meaningful fine coal preparation overview is to be possible. COAL PREPARATION DEFINED In the opinion of the writer, the term "coal preparation" should be defined as including all work activities that are performed on all components of a run-of-mine coal from the time it leaves a surface reserve or an underground portal, until all components are either ready for shipment or are stowed on, or in the earth in an environmentally acceptable manner. This definition excludes the work that is performed to improve coal quality or handleability inside the mine or pit. This work is commonly called "face" or "pit" preparation. FINE COAL DEFINED The term "fine coal" means different things to different people. In the past, anthracite finer than No. 3 Buckwheat (3/16 in.) was considered fines which often were discarded from the breaker as an unsalable by product; and bituminous coals finer that about 1/4 in. (slack) were either discarded or sold at cost to prevent an accumulation of "no bills" which referred to a product having no immediate sale. Although a standard definition of "fine coal" is yet to be accepted by the industry, a designation of coals by particle-size range has evolved through the wide use of three-circuit flowsheets, wherein the optimum size range by washer type determines the size fractions: a coarse-coal circuit for the plus 3/8 in., a -11- coal circuit for the 3/8 in. x 28 Mesh, and a fine-coal circuit for the remaining 28 Mesh x 0. Logically, the term "fine coal" should refer to some resultant size fraction or some top size by zero. This definition should include a 28 Mesh x 0 feed to a flotation cell but should exclude a 28 x 100 Mesh size fraction fed to a heavy media cyclone. Failure to include the resultant sizes in the definition precludes accounting of the full range of particle sizes present in the feed to the plant. Since the 28 Mesh x 0 fraction is treated in the final circuit of the three discreet washing circuits, now almost always used in U.S. commercial applications, and since it contains all of its resultant sizes, in the writer's opinion, it should be designated "fine coal". FINE COAL CLEANING Cleaning coal fines, which in the past was at best marginally profitable, is now an essential part of coal preparation strategy for a number of reasons : 1. Raw coals now cost more to produce and

Jan 1, 1988

By V. Patarini, M. Salkind

BECAUSE of its high strength and stiffness coupled with low density, continuous boron filament is showing great promise as a potential reinforcement for both metals and nonmetals. Of primary consideration for structural applications is the fatigue behavior of boron fiber composites. Composite fatigue behavior is dependent upon three factors: 1) fiber fatigue behavior, 2) matrix fatigue behavior, and 3) the effect of the interface and fiber ends. The purpose of this note is to describe the behavior of boron filament in rotating beam fatigue. The filament, described by Talley' and Galasso, Salkind, Kuehl, and Patarini,' was made by the hydrogen reduction of boron trichloride on a hot tungsten filament. Testing was performed using a commercial rotating beam wire fatigue tester* described by Votta.~ One end of the test sample is held in a chuck in a synchronous motor. The sample is bent around in a "U" shape, and the other end inserted into a carbide bushing. The maximum strain occurs at the bottom of the "U" where the radius of curvature is a minimum. The strain is adjusted by adjusting the length of the specimen and the location of the bushing. Samples were rotated at 3600 rpm and an automatic shutoff device used to determine the number of cycles to failure. The measurements were accurate to the nearest 360 cycles. The fatigue behavior is summarized in Fig. 1 for fifty-one samples of 4.8 x 10"3 in. diam fibers and ten samples of 3.2 X 10"3 in. diam fiber. The two sample groups represent two different filament production runs and two different nominal size groups. Both groups exhibited nominal tensile strengths of 400,000 psi. No significant difference in the fatigue behavior of the two sample groups is apparent. The scatter in the data is not unexpected for a brittle filament which exhibits a tensile strength distribution with a standard deviation of 10 to 15 pct. Because the test procedure provides a known outer fiber strain in the sample, the maximum stress was calculated assuming a Young's modulus of 58 x 10' psi. This value was selected as being representative of several nominal fiber sizes.2 All of the samples which failed exhibited sudden, catastrophic fracture, and no permanent deformation. One sample was stopped after 1.66 x lo8 cycles at *200,000 psi. The fiber exhibited no apparent damage or deformation. It is apparent that the fatigue resistance of boron filament is quite good. It can therefore be speculated that the fatigue behavior of boron fiber composites would be controlled by the "weaker links", namely matrix fatigue resistance and interface behavior. In fact, preliminary investigations have revealed that this is true for boron-reinforced aluminum? It should be noted that the data presented herein may not necessarily reflect the tensile fatigue behavior of boron filament. It is well-known that boron filament has a radial residual stress pattern with the outer surface in ~om~ression.~ Because of this fact, tensile failure is normally nucleated in the interior of the filament.5 Since the data presented herein is for a rotating beam test in which only the outer surface of the fiber is stressed to the maximum value, it would be incorrect to assume that the failure mechanism and fatigue behavior would be the same if the fiber were tested in tensile fatigue. The fact that many of the data are well above the nominal 400,000 psi tensile strength would tend to support this argument. The authors would like to express their appreciation to the United Aircraft Research Laboratories for supporting this investigation and for permission to publish the results. A portion of this effort was supported by the Air Force Materials Laboratory under contract AF33(615)-2125.

Jan 1, 1968

By J. P. G. Farr, R. Brownsword

THE role of solute segregation in the formation of cellular solidification substructures in tin and its dilute alloys is well-established, see, e.g., Ref. 1. Segregation has been shown to persist during cooling, enabling solidification structures to be studied from sections taken at some distance behind the interface. In the present work, a single crystal of commercial nickel, 99.965 pct, was examined in this way. The crystal was cut from the center of a rod given a single pass in an electron beam floating zone melter. Polished sections of a nickel specimen taken normal to the growth direction showed a very fine precipitate phase, the distribution of which varied over the section. The identification of the phase proved difficult because of the small amount present and the small particle size, about 1 p: but it was shown by probe microanalysis to contain only nickel and oxygen in detectable concentrations and was probably nickel oxide, NiO. Bulk analysis of the material before melting showed there to be only 3 to 4 ppm of oxygen present, thus demonstrating a very considerable segregation concentration effect. In some areas of the section the precipitate formed a discontinuous hexagonal network suggesting decoration of the cellular boundaries known to be present in the sample2 whereas in a restricted region the precipitate formed small clusters. Occasionally it could be seen that the clusters were at the intersections of an hexagonal network of cellular dimension. It was suggested3 that this was the result of enhanced segregation to the cell boundary intersections whereas general cell boundary segregation was insufficient to give a precipitate. Enhanced nodal segregation has since been demonstrated in a number of systems.1, 4-8 The development of a suitable electrolytic etching technique (perchloric acid 20 pct v/v; ethyl alcohol 70 pct; glycerol 10 pct; current below electropolishing plateau; 1 to 2 sec etching) suggested the association of the phase with regions of solute segregation (where ko < 1); in these regions anodic attack produced grooves or depressions. In a study of the variation of solidification substructures with degree of constitutional supercooling, Biloni et a1.&apos; appear to have used standard growth conditions and varied the solute concentration. They were able to produce in a series of individual tin crystals examples of substructure ranging from planar interface through various cellular structures to den- Fig. 1—Electroetched section taken normal to the rod axis; the center of the rod lies to the left and the periphery to the right of the micrograph. The variation of structure across the section is evident. Magnification 60 times. drites. It was possible in the present nickel crystal to observe a continuous range of substructures varying with degree of supercooling across a single section as shown in Fig. 1. Growth rate, 13 mm per min, and temperature gradient were essentially constant; the variation in structure is thought to be due to a radial gradient in solute concentration ahead of the solid interface. The liquid at the interface is likely to have been richer in solute toward the periphery of the zone, the result of curvature of this interface. The type of substructure was seen to vary with increasing constitutional supercooling as follows: a) region free of precipitate. top left, Fig. 1: 6) region of nodal precipitates which became arranged in hexagons on passing from the center of the rod: c) irregular hexagonal cells with incomplete boundary precipitation; d) regular hexagonal cells of decreasing size with complete boundary precipitation. Fig. 2 shows the transition from stage 6 and Fig. 3 shows the structure in stage d. Within stage 0, the range of conditions over which irregularly positioned nodes occur appears to be small and the nodes are soon recognizable as taking up positions at the intersections of an hexagonal network as the supercooling increases.

Jan 1, 1970