Search Documents

By G. E. Keller, G. D. Coe

Several methods have been devised for rapid determination of sulfur in coal using a high-temperature combustion furnace. The fundamental principles of the various methods are similar but the techniques vary widely. The method described herein is no different in principle from some of its predecessors but varies considerably in technique. Originally devised to overcome the low-accuracy criticism leveled against the others, the tube-furnace method has proved successful for limited applications. Work is being done to widen the applicability of the technique. Subsequent to the work of A. Vita1 in 1920, a number of investigators have published data dealing with the rapid determination of sulfur in coal using a high-temperature combustion furnace.2-5 These, together with several unpublished methods, involve wide differences in technique although they are all similar in principle. Investigation of typical details of procedure showed that poor precision or accuracy could be attributed to one or more of the following: 1) inadequate quantity of sample to be representative, 2) a delivery tube temperature too low to confine condensation to a washable area of the tube, 3) no provision for back washing the delivery tube, 4) incomplete absorption of the sulfur compounds due to inadequate bubbler, and 5) the false assumption that all of the sulfur is evolved as sulfur dixoide. The method herein discussed is no different in principle from some of its predecessors; the differences are in technique. Although the method is rapid—a determination can be completed in 5 min— accuracy has riot been sacrificed in order to achieve speed. MATERIALS AND EXPERIMENTAL WORK Fig. 1 shows the arrangement of the equipment. A metered volume of oxygen is passed through calcium chloride for removal of moisture, then through Ascarite for removal of carbon dioxide, and thence through a glass tee to the feed end of the combustion tube. Connected to the side arm of the glass tee is a rubber tube that is closed with a pinch clamp during combustion of a sample. The products of combustion are expelled through a Vycor bubbler, the end of which is submerged 3 cm below the surface of a 1 pct hydrogen peroxide solution contained in a 300 ml high-form beaker. At the completion of the 4-min combustion period the contents of the beaker are titrated to a yellow end point, using a methyl red indicator, with 0.05 N sodium hydroxide (or sodium tetraborate). The pinch clamp on the tube leading from the tee in the oxygen line is then opened and mouth suction applied to draw the hydrogen peroxide up into the bubbler past the ell, almost to the rubber tube connecting the bubbler to the combustion tube. This washing of the bubbler is repeated until no further acid reaction with the indicator is obtained. The hydrogen peroxide-sul-furic acid solution is then titrated to the final yellow end point. Test work conducted at the Robena Laboratory disclosed the following critical conditions that had important bearing on the precision of the method: Weight of Sample: Several series of tests wherein the sample weight ranged from 0.1 to 0.5 g of -60 mesh coal showed that the lowest variance (standard deviation squared) resulted from the use of 0.5-g samples; the variance was slightly greater when 0.3-g samples were used, and with less than a 0.3-g sample weight the variance increased rapidly with decrease in weight. Although the use of a 0.5-g sample invariably resulted in a very slight explosion as soon as the sample entered the hot zone of the combustion tube, this did not detract from the precision of the method. Temperatures: Mott and Wilkinson5 found that a combination of low temperature (1250°C) and low oxygen flow rate (less than 700 ml per min) tended to give high results due to formation of oxides of nitrogen. Although the method herein employs a much higher oxygen rate than 700 ml per min, as an additional precaution to assure accurate results, 1315°C (2400° F) is recommended as the most desirable furnace temperature. The temperature of the elbow of the bubbler should be at least 75°C to minimize condensation

Jan 1, 1961

By Arnold O. Tanner

The domestic mining industry continued to be strengthened and revitalized in 1989. The healthy conditions and the industry comeback that began in 1987 continued to spread and became more established for many commodities. Relatively comfortable and stable commodity prices, still found predominantly in the metals sector, reinforced other operational factors in bringing vitality to the mining and mineral processing industries. New streamlined business practices, mine and plant modernizations, and the progressive use of new technologies successfully helped lower operating costs and increase efficiency during the past 5 to 7 years. An element common to these three factors of industry renewal and growth was the ever-increasing infusion of and growing dependence on constantly advancing computer technology applications. This trend of increasing computerization was occurring throughout the mining and mineral processing business while it similarly was in most facets of modern business and culture. Some commodities and companies still struggled to outlive sluggish prices and other unstable market conditions or to modernize their businesses, but increases in productivity and profits were more common. A trend toward increased mechanical excavation in nonsoil materials was beginning to surface as a substitute for standard cyclic mine development techniques, such as drill-and-blast and surface shovel-and-truck routines. More continuous mechanical excavation offered the potential for increased production, fewer people at the working face, better ground control, and generally improved safety. The main limitation was rock hardness. The construction industry had already recognized the benefits of tunnel-boring machines for long underground drives and mechanical planers for pavement removal. The Colorado School of Mines held a short course during the year entitled, "Mechanical Excavation Techniques in Mine Development and Production,'" which was at-tended by nearly 100 engineers from 12 countries. The consensus of attendees was that for the most efficient use of these machines and techniques, new mining plans needed to be developed beyond the simple adaptation of those excavators to existing mine plans.1

Jan 1, 1991

By Niles E. Grosvenor

One of the most important considerations in the efficient operation of an under¬ground mine is the haulage system. Often the determining factor between profit or loss is the quick removal of ore and waste from the working places to secondary and main-line haulage areas, and so on to the outside. Important, too, is moving supplies from the surface to the working faces so that the loading process can continue with little interruption. Men must he transported in a rapid but safe manner. It has been through the efficient use and generally the combination of mine cars, track, belt conveyors and rubber-tired haulage equipment that underground operations have been able to compete with the more popular strip or surface mining. As near-surface ore bodies are exhausted, underground haulage will play an expanding part in economically furnishing the world's needs for all types of minerals. The choice of underground haulage equipment, wherever possible, should be one that will give the smallest overall cost of ore removal during the life of the mine while meeting necessary safety requirements. The reader is referred to Sec. 12 for equipment such as scrapers and load-dump-¬haul units that perform loading as well as haulage duties. 14.1-MINE CARS AND TRACK NILES E. GROSVENOR Main-Line and Secondary Haulage-Many mines today use a combination of belt and rail haulage. Even if a- belt system is used to carry the product from the face to the surface, track is used to transport workmen and supplies. A track system, when properly installed, will provide interruption-free and safe haulage. Schrecengost 2 lists the following as major advantages of track haulage: 1. Safety in transporting men in and out of the mine in personnel cars. 2. Easy and rapid transportation of supervisory personnel. 3. A temporary shutdown occasioned by a roof fall or power failure along the haulage system will not shut down the production areas. 4. Quick availability of repair parts and supplies. 5. Large pieces of coal or rock can be handled without damage to the haulage equipment. 6. In areas where quality fluctuates noticeably, different cars may be separated out for special preparation. 7. Rock or equipment may be loaded and moved out of the mine without interference with the production or preparation of the coal. 14.1.1-MINE CARS Mine cars with steel bodies are used in all types of present-day mining. Wooden cars usually are more bulky and less resistant to wear and damage, but are more easily repaired. Regardless of the type of mine car selected, it is most practical to standardize on one type or make to simplify repairs and limit the amount of spare parts necessary to stock. Rigid-body flat-bottomed cars are simpler and usually lower than others of equal capacity. Advantages are: ease of loading because of the low sides, simplicity, cheapness and high ratio of capacity to weight. The disadvantages include the

Jan 1, 1973

By GLENVILTE A. COLLINS

(Presented at a Meeting of the Spokane Local Section of the Institute, Feb. 17, 1912, and accepted for publication in the Bulletin. ) WHILE I am not at the present time engaged in active mine-management, my duties permit of extensive study and examination of many mines, mills, and reduction-works in various places throughout the United States. Being much interested in efficiency-work in general, and an ardent reader of writings on this subject by Frederick W. Taylor and others, as applied to manufacturing-plants, and having served my apprenticeship from mucking to the engineering design of ore-dressing and underground plants, I hope that this paper will lead others to investigate the field more fully, to the improvement of general mine- and mill-operations, as well as the advancement, intellectually, physically, and financially, of the employee and his relations with the employer. If a man who is prepared to look closely and observe broadly starts in Canada and zig-zags from camp to camp to southern Mexico, taking time casually to inspect mines, mills, and smelters, he will be pitifully impressed by the great difference in customs, and the general waste of labor, time, and money throughout the country. He will so seldom observe a dollar's worth of results given in exchange for a dollar spent that he will form a poor opinion of operating-efficiency and management. This highly-scientific department, requiring an amount of skill and executive ability equaled in few, if any, of the professions, certainly falls short of the standard established in our greater manufacturing industries. It is easily said that this is due to the diversity of conditions in mining, milling, and smelting. But on second view it must be admitted that there is room for tremendous improvements in nearly every mining-organization. The proposal of such improvements is often met by the argument that any mine

Sep 1, 1912

By Y. Prevost, D. Verhelst

"A computer-assisted process control system for the Noranda Process Reactor Wa5 installed at the Home smelter in 1991. Operating as an advisory tool for the furnace operators, and using a flexible oxygen balance as the basic building block of the computer program, the new control system has helped to reduce the variability in the grade of the matte produced by 50% . The smelter is currently operating at a 72% copper matte, with a standard deviation of between 1.0 and 1.3, while treating a wide range of concentrates, secondary materials and scrap. Enhanced process control has allowed for longer reactor campaigns, and improved stability of the converting operation.This paper reviews the feed classification and blending practice used at the smelter, outlines the strategy of the new computer control system, and summarizes the benefits realized since the implementation of the system in early 1990.IntroductionUntil 1989 the Noranda Home smelter operated as a multi furnace smelter, at one time having three hot-charge reverberatory furnaces, and finally operating with one wet-charge reverberatory furnace and one Noranda Process Reactor. In 1989 the final reverberatory furnace was closed and the Reactor became the sole smelting vessel, treating around 750 000 tonnes of concentrate, secondary materials, and scrap per year. At the time of the start-up of theNoranda Reactor in 1973, the vessel was capable of treating 750tonnes per day of a heterogeneous mixture of copper concentrates, fluxes and secondary materials to produce copper in one operation. Through process improvements, and the introduction of additional oxygen in 1982(pannell and Mackey, 1988), the daily tonnage increased to 1800 tonnes by 1988. The operation had also been changed to produce a high-grade matte instead of copper. Figure1 illustrates the main features of the reactor, a cylindrical vessel which is charged at one end and tapped at the other. The matteis subsequently processed through Peirce-Smith converters and anode furnaces before being cast into copper anodes. Figure 2 outlines the progressive increase in the furnace smelting capacity. Over this period the percentage of secondary materials, and scrap feeds also increased to approximately 110 000 tonnes per year, or 15% of the total new feed input (Bedard et al., 1991). Now operating wholly as a custom feed operation, the Home smelter can treat over 2200tonnes per day of new metal-bearing material."

Jan 1, 1993

By G. H. Bruce, C. E. Williams

The trend toward deeper drilling, together with the attcndant increase in power requirements for circulation of the drilling fluid, has emphasized the need for a critical examination of the factors affecting the removal of bit cuttings from the hole by the drilling fluid. The ability of drilling fluids to lift cuttings is called their carrying capacity. A series of laboratory and field experiments has been conducted to determine the minimrim annular velocity necessary to remove cuttings, and to investigate the effects of properties of drilling fluids on their carrying capacities. Consideration of the results of these experiments led to the following conclusions: 1. Turbulent flow in the well annulus is most desirable from the standpoint of cutting removal. 2. Low viscosity and low gel are advantageous in removing cuttings. 3. Increase in mud weight is effective in increasing carrying capacity. 4. The carrying capacity is higher when the pipe is rotated than when it is not. 5. If turbulent flow can be maintained, an annular velocity slightly higher than the slip velocity of the largest cuttings to be transported should keep the bore hole clean. This implies velocities of 100 to 125 ft per minute rather than the presently used 175 to 225 ft per minute. INTRODUCTION Power Savings by Reduction of Annular Velocities A large portion of the power expended in drilling operations is consumed in circulating the drilling fluid. An important factor in establishing the rate of mud circulation is the minimum velocity in the annulus necessary to remove bit cuttings. Empirically, it has been found that average annular mud velocities of about 200 ft per minute will remove cuttings. It was not definitely known, however, whether annular velocities of about 200 ft per minute were just above the minimum necessary to remove cuttings, or whether such velocities could be materially reduced without sacrifice of the ability of the mud to remove cuttings. It is apparent that if annular velocities could be reduced without impairment of cutting removal, a considerable saving in power requirements would result. Need for Research on Carrying Capacity The ability of a drilling fluid to transport cuttings is called its carrying capacity. Although it has been recognized that the carrying capacity of a mud is affected by mud properties such as viscosity and density1,2,3,4 there have been various views in the industry as to the effects of these mud properties on carrying capacity. The economic importance of the problem of carrying capacity and the scarcity of information on the subject indicated that research on the problem was needed. THE FACTORS AFFECTING CARRYING CAPACITY Qualitative Determination of Factors The mechanism of cutting transport is closely related to that involved in the separation of material by settling processes. A considerable amount of research has been done on settling problems, and discussions of sedimentation theory can be found in standard texts.5,6 Consideration of the information available from these sources, together with consideration of the mechanism of cutting transport, leads to the conclusion that the factors affecting carrying capacity are the dimensions of the system, the physical properties of the cuttings. and the physical properties of the drilling fluid. system Dimensions and Their Effect The dimensions of the fluid circulating system of importance to carrying capacity are the bore hole size, drill pipe size, pump capacity, and pump speed. These dimensions determine the annular velocity of the drilling fluid. Physical Properties and Their Effects The physical properties involved in the interaction between mud and cuttings are the density and shape of the cuttings and the density, viscosity and gel strength of the drilling fluid. The effect of the density factor on carrying capacity is fairly obvious; high density difference between cuttings and fluid results in a low buoyant force and therefore decreases carrying capacity. The effect of cutting shape is less obvious. Although

Jan 1, 1951

By G. Derge, Ling Yang, John Henderson

Self-diffusion coefficients of aluminum have been measured by the capillary reservoir technique in liquids of the CaO-SiO2-Al2O3 system containirg equimolar portions of CaO and SiO2, in the temperature range 1400o to 1520oC. For the melt containing 6.0 mole pct Al2O3 the results can be expressed by the equation D = [(4.3 * 0.3) x 104] exp [(-85,000 * 17,500)/RT]cm~sec-'; for the melt containing 12.5 mole pct Al2O3, by the equation D = (5.4 i 0.2) exp [(-60,000 * 10,00O)/RT] cm2sec-: A concept of the constitution of these melts has been developed which proposes that the ratios O/(Si +Al) and Al2 O3/CaO determine the dominant species present. In recent years considerable work has been done on the system CaO-SiO2-A12O3 with a view to elucidating the structure of liquids of this system. Conductivity,' electromotive force, 3 density,4 and activity5 measurements have all contributed to an understanding of the problem, but as yet there is no entirely satisfactory theory that can account for all the observed experimental results. In principle, measurements of self-diffusion coefficients should give further information which is not obtainable in other ways. Self-diffusion coefficients for calcium, silicon,6 and oxygen7 have been measured. The present investigation extends the series of self-diffusion coefficient measurements to include aluminum and develops a concept of constitution for liquids of this system which is compatible with all the observed experimental results. EXPERIMENTAL The technique used in the measurement of the self-diffusion coefficient of aluminum was the capillary-reservoir method,8 A126 being incorporated in the melt contained in the capillary and inactive aluminum in the reservoir melt. This method was chosen because it minimizes convection currents' in the diffusion zone. It has the further advantage that the boundary conditions are such that a slight modifica- tion of Anderson and saddington's8 solution of Fick's Law yields an equation which requires measurements only of the length and the initial and final average specific activities of the solidified melt within the capillary. where t is the diffusion time, Co is the average specific activity of the melt contained in the capillary at t = O, C is the average specific activity of the melt contained in the capillary at t = t, 1is the length of the capillary, and D is the self-diffusion coefficient. The equation is of somewhat different form than those previously applied to high temperature diffusion studies because the specific activity of the melt in the reservoir was negligible both before and after diffusion. The diffusion apparatus is shown schematically in Fig. 1. It consisted of a silicon carbide resistance furnace containing the inactive melt in a graphite crucible, internal dimensions 7/8 by 4 in., enclosed in a 1 1/4- by 1 1/2- by 30-in. McDanel tube. A 3/8-in. McDanel thermocouple sheath to which graphite radiation shields and a graphite protection tube were affixed, was used to hold the capillaries. By moving this sheath through a rubber seal at the top of the McDanel tube the capillaries could be lowered into or raised out of the melt. Temperature was measured with a Pt-Pt 13 pct Rh thermocouple which was calibrated periodically against a standard couple. The furnace temperature was controlled to ± 5°C through the thermocouple immersed in the melt. Temperature variation over the depth of the melt was less than ± 3°C. The inactive melts were prepared from pure native quartz, assaying better than 99.9 pct SiO2, A.R. grade A12O3 and A.R. grade CaCO,. The same quartz and CaCO3 were used in preparing the active melts, the

Jan 1, 1962

By Klaus Schwerdtfeger

In order to test the performance of ZrO, (CaO) and Tho,(Yz03) electrolytes in the electrochemical determination of oxygen activities in liquid metals at steel-rrzakitng temperatures , electromotive force measurements have been made with the following cells: The oxygen-- activities are calculated from the electmrnotive forces for the investigated systems. The standard free energy of- formation of MnO and the activity of manganese in Fe-Mn melts are derived. Indications are that the Zr 0z(Ca0) electrolyte exhibits little electronic conductivity at oxygen pressures as low as 10'a atnz at 1600°C; however, the partial electronic conductivity may become noticeable at lower oxygen activities. The Tho,(Yz03) electrolyte is found to be an ionic conductor at the oxygen pressure as low as that for the Mn + MnO equilibrium, but exhibits partial electronic conductivity at oxygen pressures higher than 10"1 atm (1500°C). fi. better control of oxidation and deoxidation reactions in steelmaking may be facilitated if the oxygen activity in the steel is known during various stages of the process. In the present work oxygen activities have been measured in liquid iron, manganese, and iron alloys with galvanic cells using ZrOz(CaO) and s solid electrolytes with the object of establishing the range of oxygen pressure in which these materials can be used as electrolytes at steelmaking temperatures. Calcia-stabilized zirconia and Tho2-Y203 solid solutions are oxygen ion conductors. Such electrolytes were first used by Kiukkola and Wagner1 and Peters and ~ann' in galvanic cells for the determination of thermodynamicquantities of oxide systems in the temperature range 700" to 1200°C. At these moderate temperatures calcia-stabilized zirconia has been found to exhibit predominantly ionic conductivity at oxygen pressures as low as those for the Cr + Crz03 equilibrium,394 but at lower oxygen pressures elec- tronic contribution to conductivity becomes significants4 The Th02-Y203 solid solutions are ionic conductors at oxygen pressures lower than those applicable to zirconia base electrolytes.5'6 At high oxygen pressures Thoz base electrolytes exhibit significant p-type semiconduction. At the time the present experiments were carried out several papers1'-* were published on the electrochemical determination of oxygen activities in liquid iron using the ZrOz(CaO) electrolyte. The results of different authors do not agree well. For instance, according to Fischer and ~ckermann" stabilized zirconia can be used to measure oxygen contents in liquid iron larger than 0.02 wt pct, but according to Baker and west1' ZrOz(CaO) cannot be used for the determination of oxygen content in liquid iron because of high electronic contribution to the conductivity. Fig. 1 is a schematic diagram of the apparatus used. About 500 g of liquid metal is contained in a crucible into which a stabilized zirconia or Th02(Y203) tube is immersed. A platinum contact wire is pressed (with a spring mechanism) against the inside bottom wall of the electrolyte tube. The tube is flushed continuously with a stream of air, CO-CO, (or Hz-C02) (at 0.96 atm and at a rate of about 300 cu cm per min), via an alumina tube inserted inside the electrolyte tube. This alumina tube also contains the Pt-Pt/10 pct Rh thermocouple. A capillary alumina tube shielding the other contact wire is immersed in the melt. The molybdenum contact wires were used mostly; in some cases platinum wire was employed. Molybdenum has the advantage that it dissolves more slowly in the melt than platinum. The whole cell was contained in the alumina reaction tube of a resistance furnace with molybdenum winding. The reaction tube was closed gas tight at both ends and flushed continuously with argon. Because of the poor thermal shock resistance of the electrolyte tubes the cell had to be assembled in the cold furnace. The electrolyte tube and alumina sheath

Jan 1, 1968

By Kenneth E. Gray

The turbulent flow drag coefficients, or friction factors, have been experimentally determined for the cut-tings normally encountered in drilling operations. The gas law and average drag coefficients for characteristically flat particles (limestones and Shales) and for angular to sub-rounded particles (sandstones) were used to extend Newton's equation to a more useful form. The resulting equations are expressions for the slip velocity of a particle as a function of the particle size and shape, the bottom-hole injection Pressure, and the Bottom-hole temperature. The velocities necessary to lift actual rock cuttings as observed in the laboratory were compared with velocities predicted from the derived equations. Results indicate that there is no single correct circulating velocity and that the commonly used 3,000 ft/min linear velocity may he sufficient to lift only very mall particles. The advantage, in terms of horsepower requirements, of cycling high pressure air to obtain lower compression ratios was shown. INTRODUCTION A promising departure from standard rotary hydraulic drilling is air or gas drilling. In many instances the rate of penetration and bit life increases resulting from this method have been very substantial. Further the application of air drilling in areas of lost circulation or water sensitive pay zones has been highly successful. Purpose For the drilling contractor, the practical question remains, "How much air pressure and volume should I have?' lt is necessary to have a reasonable knowledge of the air velocities and pressures required in air drilling operations for the proper design and most advantageous use of surface equipment and for adequate removal of cuttings from the borehole. Eased on experience, most operators agree that at least 3,000 ft/min linear velocity is necessary for satisfactory hole cleaning.' It was the purpose of this investigation to evaluate the drag coefficients, or friction factors, for the cuttings normally encountered in drilling operations, i.e., sandstones, limestones and shales, and to utilize the values obtained to develop an expression for the minimum velocities and pressures (hence the volumes) necessary to lift these cuttings. THEORY Several investigators have done extensive work on the ability of drilling mud to lift bit cuttings. They conclude that the ability of a drilling mud to lift cuttings is dependent on the density difference between the rock being drilled and the drilling mud, the cutting size and shape, the mud flow constants, and the flow state (laminar, transitional or turbulent) of the mud. However, drilling muds are not true fluids but have a variation of viscosity with velocity in laminar flow and a constant apparent viscosity in turbulent flow. A survey of the literature revealed that no experimental work had been done to determine the velocities necessary to lift actual rock cuttings using a compressible fluid such as air or gas. In 1953, Nicolson6 stated that in air drilling fluid mechanics the particles could be assumed spherical in shape and that ; constant drag coefficient of 0.5 could be used due to the highly turbulent flow of the circulating air. By equating the turbulent resistance on the particle to the gravitational force on the particle, he obtained the expression, ^ = 2.67^y ,.......(1) where V, is slip velocity of spherical particle, ft/sec; D is particle diameter, in.; p, is particle density, 1b/ft8; and p, is fluid density, lb/ft3. However, as stated earlier, most operators seem to agree that adequate hole cleaning can be obtained by circulating a sufficient volume of air to give a linear velocity of 3,000 ft/rnin in the annular space. Basic Equation The velocity with which a solid particle freely falls through a fluid will increase until the accelerating force, gravity, is equal to the resisting forces, buoyancy due to the fluid displaced by the particle and friction due to the relative motion of the particle through the fluid. When the accelerating and resisting forces become equal,

By F. D. Rosi

The slip and twinning behavior in extended titanium crystals were studied in some detail. The formation and appearance of coarse kink bands are discussed. Their crystallographic geometry was determined by X-ray analysis. A phenomenological interpretation of the complexities in kink band development is also presented. The critical resolved shear stress, coefficient of shear hardening, and plane of fracture were determined for several crystals extended at room temperature. THE slip and twinning elements observed in the room-temperature deformation of titanium were enumerated in a previous paper1 in which considerations were advanced regarding the nature and selection of these elements and their effect on the known mechanical properties of this metal. The present study concerns the crystallographic, microscopic, and mechanical aspects of flow in relation to the slip and twinning elements, and includes a prediction of slip systems, nature of slip and twin markings, inhomogeneities of plastic flow, and stress-strain characteristics. Unless otherwise noted, arc-melted titanium sponge (99.77 pct) was used in these experiments. The method of production of crystals, their dimensions, and the surface preparation for micrographic examination have been reported.&apos; For obtaining stress-strain characteristics, only those crystals which traversed the entire width of the specimen and were at least 8 mm in length were used. Tensile deformation of the crystals was performed with conventional grips for sheet specimens and a constant-stress loading beam, designed after the method of Andrade and Chalmers.&apos; The specimens were loaded by allowing sand to flow from a reservoir into a bucket suspended from the longer end of a balanced 6:1 lever arm at a rate controlled to load the specimen approximately 2 kg per min. Strain measurements were made using the Baldwin SR-4, bonded, resistance-wire strain gage, Type A-8, which permitted a reading accuracy of 2 microinches per inch. The formulas used in the evaluation of shear stress and shear strain, as in deriving the coefficient of shear hardening, are given by Schmid and Boasv n terms of the original orientation and change in length of the crystal. For calculating the critical resolved shear stress, the standard equation was used. The crystallographic nature of the unpredictable slip observed in a number of specimens was determined by the single-surface X-ray method of analysis as described in ref. 1. Experimental Results Prediction of Slip System: It was reported&apos; that room temperature slip in titanium takes place predominantly on {10i0} and in a <1120> direction, giving three potential slip systems. Hence, it should be possible to predict the operative primary system in the manner used by Taylor and Elam&apos; for alu- minum (i.e., the one with the greatest component of shear stress in the direction of slip). The stereo-graphic construction in Fig. 1 shows that this is true. In all cases, slip was found to occur initially on the (0110) plane and, in a number of cases, in the [21f0] direction. (The direction of slip was not determined for all orientations.) It follows that duplex slip can be expected when two slip systems are geometrically equally favorable for slip, as demonstrated in Fig. 2. In both crystals slip took place simultaneously on the (1700) and (olio) prismatic planes, as indicated by Fig. 2a and b. In the case of crystal B the movement of the specimen axis with increasing extension was toward the (10i0) direction, which represents the stable end orientation resulting from alternate slip on the [2ii0] and [1120] directions. This is analogous to the duplex slip process in face-centered cubic metals." Unpredictable Slip: In a number of crystals whose orientations were well within the operation of a single slip system, secondary slip occurred on planes not predicted by the criterion of maximum shear stress. Examples are shown in Fig. 3. In addition to

Jan 1, 1955

By R. H. Oliver

The purposes, types, preparation, and testing of flocculants are discussed. A flocculation compendium is included, indicating choice of flocculant for a given set of conditions. An economic evaluation of the process is presented. Solid-liquid separation is a major expense in most mineral processing flowsheets today. Proper use of flocculation can often lower the overall cost of a solid-liquid separation by reducing the size of sedimentation or filtration equipment. PURPOSE OF FLOCCULATION When is use of a flocculant justified in terms of overall process economy? 1) when it results in process improvement, such as producing a clear liquor for electrolysis, precipitation, ion exchange, or solvent extraction; 2) when it results in satisfying requirements of pollution abatement ordinances; 3) when it results in increased recovery of values that would otherwise be lost; or 4) when it results in considerable savings in capital expenditure due to use of smaller equipment. When can the use of a flocculant adversely effect overall process economy? 1) when it results in increased filter cake moisture, 2) when it results in decreased filtration rates, 3) when it results in considerable bulking of sedimentation underflow, 4) when it contaminates either the supernatant or sludge, or 5) when the cost of using the flocculant is greater than the savings due to its use. First step in consideration of flocculants for a given application is establishment of desired goals in terms of increased clarity of effluent, increased recovery of solids, or decreased size of equipment. The most economical solution to a solid-liquid separation problem is that combination of equipment and flocculant costs which meets the established goals at the lowest total annual expenditure. This economic decision can be made only after technical data has been obtained as outlined in next four sections. TYPES OF FLOCCULATION Flocculation is a process wherein individual particles are united into more or less tightly bound agglomerates or flocs, thereby increasing effective particle size of solids suspended in a liquid. Degree of flocculation of a suspension of finely divided solids in a liquid is controlled by a combination of probability of collision between particles and probability of adhesion after the collision has occurred.&apos; Probability of collision can be increased commercially through use of a paddle-type flocculator, combination flocculator, and clarifier or flocculating-type feedwell. Probability of adhesion usually can be increased by addition of a reagent known as a flocculant. Reagents act as flocculants through one or a combination of three possible mechanisms. The first is electrolytic neutralization of inter molecular repulsive force due to Zeta potential. This neutralization enables Van der Waal&apos;s cohesive force to hold the particles together after they collide.&apos; The second is the precipitation, within a definite pH range, of voluminous metallic hydroxide flocs which entrap fine particles. This process is known as coagulation.14 Third is the bridging of two or more particles by either natural or synthetic long-chain, high-molecular-weight organic polymers. This bridging is accomplished by adsorption of two particles at different sites on the same molecule or by bonding of two molecules, each adsorbed to a different particle. Considerable effort has been expended in explaining the action of these polyelec-trolytes and detailed accounts are available in the literature. CHOICE OF FLOCCULANTS It is impossible, at the present time, to specify the optimum type or amount of flocculant for a given application from a knowledge of the material to be treated. The standard procedure is to choose reagents or combination of reagents most likely to be effective on the slurry; then test them.&apos; The accompanying Flocculation Compendium (Table I) contains details of all currently available reagents sold as flocculants and it should be used when selecting the group of reagents for tests. This selection can be based on information listed in columns 4 and 5. Column 4 presents industries in which each floc-

Jan 1, 1961

By C. E. Williams, G. H. Bruce

The trend toward deeper drilling, together with the attcndant increase in power requirements for circulation of the drilling fluid, has emphasized the need for a critical examination of the factors affecting the removal of bit cuttings from the hole by the drilling fluid. The ability of drilling fluids to lift cuttings is called their carrying capacity. A series of laboratory and field experiments has been conducted to determine the minimrim annular velocity necessary to remove cuttings, and to investigate the effects of properties of drilling fluids on their carrying capacities. Consideration of the results of these experiments led to the following conclusions: 1. Turbulent flow in the well annulus is most desirable from the standpoint of cutting removal. 2. Low viscosity and low gel are advantageous in removing cuttings. 3. Increase in mud weight is effective in increasing carrying capacity. 4. The carrying capacity is higher when the pipe is rotated than when it is not. 5. If turbulent flow can be maintained, an annular velocity slightly higher than the slip velocity of the largest cuttings to be transported should keep the bore hole clean. This implies velocities of 100 to 125 ft per minute rather than the presently used 175 to 225 ft per minute. INTRODUCTION Power Savings by Reduction of Annular Velocities A large portion of the power expended in drilling operations is consumed in circulating the drilling fluid. An important factor in establishing the rate of mud circulation is the minimum velocity in the annulus necessary to remove bit cuttings. Empirically, it has been found that average annular mud velocities of about 200 ft per minute will remove cuttings. It was not definitely known, however, whether annular velocities of about 200 ft per minute were just above the minimum necessary to remove cuttings, or whether such velocities could be materially reduced without sacrifice of the ability of the mud to remove cuttings. It is apparent that if annular velocities could be reduced without impairment of cutting removal, a considerable saving in power requirements would result. Need for Research on Carrying Capacity The ability of a drilling fluid to transport cuttings is called its carrying capacity. Although it has been recognized that the carrying capacity of a mud is affected by mud properties such as viscosity and density1,2,3,4 there have been various views in the industry as to the effects of these mud properties on carrying capacity. The economic importance of the problem of carrying capacity and the scarcity of information on the subject indicated that research on the problem was needed. THE FACTORS AFFECTING CARRYING CAPACITY Qualitative Determination of Factors The mechanism of cutting transport is closely related to that involved in the separation of material by settling processes. A considerable amount of research has been done on settling problems, and discussions of sedimentation theory can be found in standard texts.5,6 Consideration of the information available from these sources, together with consideration of the mechanism of cutting transport, leads to the conclusion that the factors affecting carrying capacity are the dimensions of the system, the physical properties of the cuttings. and the physical properties of the drilling fluid. system Dimensions and Their Effect The dimensions of the fluid circulating system of importance to carrying capacity are the bore hole size, drill pipe size, pump capacity, and pump speed. These dimensions determine the annular velocity of the drilling fluid. Physical Properties and Their Effects The physical properties involved in the interaction between mud and cuttings are the density and shape of the cuttings and the density, viscosity and gel strength of the drilling fluid. The effect of the density factor on carrying capacity is fairly obvious; high density difference between cuttings and fluid results in a low buoyant force and therefore decreases carrying capacity. The effect of cutting shape is less obvious. Although

Jan 1, 1951

By R. G. Garlick, H. B. Probst

Tungsten single-crystal specimens of various orientations were deformed in tension at room temperature. Slip traces indicated both (112)(111) and (110) (111) slip; however, about 10 pct plastic dejormation was required bejore these traces could he seen. Resolzled shear-stress considerations indicated that at least some of the particular systems observed were not those on which slip initiated hut were secondary systems. This is highly probable, considering the high plastic strains involved. Analysis of the stress data with respect to possible slip systems indicated that slip must have been initiated at stresses below the proportional-limit stresses measured. ALTHOUGH there is general agreement that slip deformation in fcc and hep metals takes place on the plane of close packing and in the direction of close packing, there is no such agreement for slip in bcc metals. It is generally agreed that the close-packed direction (111) is the slip direction, but investigations have led to conflicting descriptions of the slip plane. As Hoke and Maddin1 point out, there are essentially four points of view. 1) Deformation in bcc metals is composite shear on (112) and (110) planes or on nonparallel (110) planes, and any apparent slip on other planes can be accounted for completely by slip on these planes. Chen and Maddin have reported this to be the possible case for molybdenum." 2) Slip occurs in the (111) direction and is limited to {110), {112), and (123) planes (the three closest packed planes of the lattice). 3) Slip occurs in a (111) direction, but not necessarily on planes of close packing (banal slip). 4) Slip occurs in those directions and on those planes for which ß, the ratio of Burgers vector to interplanar spacing, is a minimum. The slip systems of the bcc metal tungsten have never been fully determined, although several investigators have reported pertinent results.3"7 The present work was initiated to determine the active slip systems in tungsten at room temperature, the critical resolved shear stresses associ- ated with these systems, and the orientation dependency of operative systems. These features of tungsten deformation at room temperature have never been reported in the literature. The authors find this somewhat surprising, particularly in view of the availability of tungsten single crystals since the advent of electron-beam zone-melting techniques and the widespread interest in refractory metals. It would seem apparent that such work has been attempted but the results have not been reported, possibly due to the conflict with deformation theory. The results of the present work conflict with any straightforward description of deformation based on the proposed explanations of slip in bcc metals. Although these conflicts have not been resolved, a presentation of the problem seems in order and should be of value to others working in this field. MATERIALS AND PROCEDURE Single-crystal tungsten rods of 1/8-in. diameter were grown from undoped commercial rod by one-pass electron-beam zone melting in apparatus previously described by witzke.8 Representative analyses of the rod before and after melting are given in Table I. There was no detectable zoning of impurities during melting. Buttonhead tensile specimens, as shown in Fig. 1, were machined from single crystals. Two flats 90 deg apart were ground in the gage length of each specimen. These flat surfaces facilitated the analysis of slip traces. No attempt was made to position these flats with respect to the crystal orientation. The worked surface layer of the machined specimens was removed by electrolytic polishing in a NaOH solution. Tensile-axis orientations were determined by standard Laue back-reflection techniques. The sharpness of the Laue spots indicated that the crystals were free of strain.

Jan 1, 1964

By Jack E. Thompson

Thank you Tom and JM for that nice introduction. The remarks I am about to make rely on a large way on comments made by Barrick&apos;s Chief Counsel, Patrick Garver, to an internal meeting of Barrick&apos;s senior staff. I plagiarized so much from his notes that I thought that I should provide attribution. I did get his consent to borrow so freely. What I have done is take his general comments and used my conversations with CEO&apos;s and other participants in the industry to enhance the message with concrete examples that underscore the points I wish to make. What you are about to hear is my personal view – I am not speaking as a representative of any company. With that introduction, now would be a good time to give you the main theme of my talk: The SEC should change its rule making to a more public cooperative approach. If that were to happen the SEC would avoid some of the harm it has been doing to the companies in this sector and the very shareholders it seeks to protect.

Jan 1, 2003

Tars Committee is the result of a desire of the authorities in charge of the publications of the four national engineering societies to co-operate in this matter. The members of the Committee are the following: Charles WarreN Hunt, Secretary of the American Society of Civil Engineers. D. S. Jacobus, Vice-President of the American Society of Mechanical Engineers. Joseph Struthers, Assistant Editor of the American Institute of Mining Engineers. CaRy T. Hutchinson, Chairman of The Editing Committee of the American Institute of Electrical Engineers. This Committee has held several meetings; it seemed advisable, at the outset, to limit its discussions closely to the general subject of abbreviations. Further, it seemed best to formulate a few general rules to be followed in making abbreviations, rather than to compile a list of forms to be recommended. The Committee decided to limit the subject more narrowly by considering only abbreviations to be used in the text, or general reading-matter, arid not those to be used in special matter,

Jan 1, 1905

By D. L. Harris, A. M. Gaudin

Observations were made of the distribution of mercaptan containing S35 between aqueous solution and mineral and between aqueous solution and the gaseous phase. Although equilibrium may not have been attained, adsorption of the reagent was shown to occur reasily from air or aqueous solution on sphalerite, zincite, and willem-ite and to correspond to flotation. Adsorption on quartz did not similarly occur. THE following results, presented here in condensed form,&apos; were obtained in a preliminary study of the adsorption of n-hexane thiol, hexyl mercaptan, on sphalerite, zincite, willemite, and quartz, from aqueous solution and from a gas. Interest in this subject was aroused by a Belgian report&apos; of effective use of hexyl mercaptan for flotation collection of oxidized zinc minerals. The relatively low boiling point, 149°C, of the mercaptan3 suggested the desirability of extending the usual measurements of partition of collector between aqueous solution and gas and between gas and mineral. It is believed that this paper presents the first measurements of this type on a flotation system. Attempts were made to carry out the measurements at equilibrium, but as the work progressed it became increasingly doubtful that this desirable condition had been achieved. To control composition and extent of the gas phase, the apparatus was a wholly-enclosed thermally-controlled glass system. Because of these constraints and the desirability of dealing with pure minerals, a scale of operations was chosen in which a few grams of deslimed mineral were used in each test. It was also necessary to choose a particularly sensitive method for mercaptan analysis, and in fact a method that would permit the experimenters to follow the approach to equilibrium. For these reasons mercaptan marked by radiosulphur 35 was used. An analysis was made for the radiosulphur by a modification of the method of Gaudin and Carr. Coarsely-crystallized sphalerite was handpicked, stage-crushed in the dry state, wet-screened on a 200-mesh sieve, and deslimed in water at about 5 microns. Further treatment consisted of a wash in dilute aqueous hydrogen peroxide, drying, removal of the dark-colored fraction in a Frantz magnetic separator, washing in very dilute hydrochloric acid, repeated washing in distilled and conductivity water, and drying. The last washings showed a conductivity equivalent to a few ppm NaC1, that is, much more than would be provided, theoretically, by a saturated ZnS solution. The material was stored dry in sealed bottles. Analyses were as follows: Zn, 62.3 pct; Fe, 0.43 pct; Cd, 0.44 pct; S, 31.2 pct; Mn, 0.001 pct. The specific surface (BET method) was 2000 cm2/g. Zincite from Franklin furnace of the New Jersey Zinc Co. was hand-picked, dry-crushed, wet-screened at 100 mesh, and deslimed at about 10 microns. After drying, the associated zinc, manganese, calcium, and silicate minerals were removed in a Frantz magnetic separator. The purified zincite was washed in distilled water and conductivity water to a conductance of less than 2 ppm equivalent NaC1, dried, and stored. Analyses were as follows: Zn, 75.1 pct; Fe, 0.9 pct; Mn, 2.78 pct. The specific surface (BET method) was 1740 cm 2/g. Willemite, also from Franklin furnace, was purified similarly. Analyses were as follows: Zn, 52.5 pct; Fe, 0.12 pct; SiO², 27.3 pct; loss on ignition, 0.13 pct. The specific surface was 1760 cm 2/g. Conductivity water (double-distilled) and demin-eralized-distilled water were used in most of the tests. The specific resistance was not less than 600, 000 ohms, and usually above 1,000,000. Radiosulphur-marked hexyl mercaptan (1-hexane thiol) was synthesized by Tracerlab, Inc., Boston. Two lots were secured several months apart. The last lot, consisting of about 0.5 g of the mercaptan, had a total activity of about 10 millicuries. Tracerlab Co. guaranteed only the activity; hence a quasi -vapor pressure determination (based upon an S analysis) of the mercaptan was made. The calculated value, 4.2 mm of mercury at 25.5&apos; C, has been compared with that of a sample of Highest Purity 1-hexane thiol from Fisher Scientific Co. The latter had a vapor pressure of 4.5 mm of mercury at 2.5 C. Analytical Procedures The sample containing radiosulphur-marked mercaptan was oxidized to convert the mercaptan sulphur to sulphate, carrier barium sulphate being added to provide a suitable quantity of total barium sulphate in a filter cake. The precipitate was filtered and dried, and counting was carried out either in a streaming-gas (Q-gas) counter for high sensitivity or with an end-window G-M counter for convenience. The oxidized and precipitated mercaptan gave a radioactive count of 65 counts per minute per microgram in the end-window Geiger-Mueller counter and 1100 counts per minute per microgram in a Q-gas counter. For standardization of the mercaptan solution, 15 replicate analyses were made. The average deviation per measurement was about 1600 cpm in 65,000 cpm, the probable error in the mean being 275 cpm. It

Jan 1, 1955

By Rollyn P. Jacobson

THE town of Pacific, in Jefferson County, Mo., is 127 miles west of St. Louis. Since the area lies entirely on the flood plain of a cutoff meander of the Meramac River, it was considered a likely environment for accumulation of commercial quantities of sand and gravel. Excellent transportation facilities are afforded by two major railways to St. Louis, and ample water supply for washing and separation is assured by the proximity of the river. As a large washing and separation plant was planned, the property was evaluated in detail to justify the high initial expenditure. An intensive testing program using both geophysical and drilling methods was designed and carried out. The prospect was surveyed topographically and a 200-ft grid staked on which electrical resistivity depth profiles were observed at 130 points. The Wenner 4-electrode configuration and earth resistivity apparatus" were used. In all but a few cases, the electrode spacing, A, was increased in increments of 11/2 ft to a spread of 30 ft and in increments of 3 ft thereafter. Initial drilling was done with a rig designated as the California Earth Boring Machine, which uses a bucket-shaped bit and produces a hole 3 ft in diam. Because of excessive water conditions and lack of consolidation in the gravel there was considerable loss of hole with this type of equipment. A standard churn drill was employed, therefore, to penetrate to bedrock. Eighteen bucket-drill holes and eight churn-drill holes were drilled at widely scattered locations on the grill. The depth to bedrock and the configuration will not be discussed, as this parameter is not the primary concern. Thickness of overburden overlying the gravel beds or lenses became the important economic criterion of the prospect.** The wide variety and gradational character of the geologic conditions prevailing in this area are illustrated by sample sections on Fig. 2. Depth profiles at stations E-3 and J-7 are very similar in shape and numerical range, but as shown by drilling, they are measures of very different geologic sequences. At 5-7 the gravel is overlain by 15 ft of overburden, but at E-3 bedrock is overlain by about 5 ft of soil and mantle. Stations L-8 and H-18 are representative of areas where gravel lies within 10 ft of surface. In most profiles of this type it was very difficult to locate the resistivity breaks denoting the overburden-gravel interface. In a number of cases, as shown by stations M-4 and H-18, the anomaly produced by the water table or the moisture line often obscured the anomaly due to gravel or was mistaken for it. In any case, the precise determination of depth to gravel was prevented by the gradual transition from sand to sandy gravel to gravel. In spite of these difficulties, errors involved in the interpretation were not greatly out of order. However, results indicated that the prospect was very nearly marginal from an economic point of view, and to justify expenditures for plant facilities a more precise evaluation was undertaken. The most favorable sections of the property were tested with hand augers. The original grid was followed. In all, 46 hand auger holes were drilled to gravel or refusal and the results made available to the writer for further analysis and interpretation. When data for this survey was studied, it immediately became apparent that a very definite correlation existed between the numerical value of the apparent resistivity at some constant depth and the thickness of the overburden. Such a correlation is seldom regarded in interpretation in more than a very qualitative way, except in the various theoretical methods developed by Hummel, Tagg (Ref. 1, pp. 136-139), Roman (Ref. 2, pp. 6-12), Rosenzweig (Ref. 3, pp. 408-417), and Wilcox (Ref. 4, pp. 36-46). Various statistical procedures were used to place this relationship on a quantitative basis. The large amount of drilling information available made such an approach feasible. The thickness of overburden was plotted against the apparent resistivity at a constant depth less than the depth of bedrock for the 65 stations where drilling information was available. A curve of best fit was drawn through these points and the equation of the curve determined. For this relationship the curve was found to be of the form p = b D where p is the apparent resistivity, D the thickness of overburden, and b a constant. The equation is of the power type and plots as a straight line on log-log paper. The statistical validity of this equation was analyzed by computation of a parameter called Pearson&apos;s correlation coefficient for several different depths of measurements, see Ref. 5, pp. 196-241. In all but those measurements taken at relatively shallow depths, the correlation as given by this general equation was found to have a high order of validity on the basis of statistical theory.

Jan 1, 1956

By C. L. Prokop

A laboratory investigation has been made of the effects of mud hydraulics upon the formation and erosion of mud filter cakes. The tests were conducted to simulate drilling conditions as nearly as possible. The formation of mud filter cake in a drilling well does not proceed at a uniform and unbroken rate. Instead, the rate of cake accumulation depends upon whether or not the mud is being circulated. If the mud column is quiescent, filter cake formation is a smooth function of the filtration characteristics of the system. If the mud is being circulated filter cake formation depends not only upon the filtration characteristics of the mud but also upon the erosive action of the flowing mud column Filter cakes formed during continuous mud circulation were observed to reach an equilibrium thickness after several hours&apos; circulation. Mud circulation was maintained at a constant volumetric rate throughout each experiment. The fluid velocity at equilibrium cake thickness was dependent upon the thickness of the filter cake. Muds having exceptionally high water loss deposited thick filter cakes in spite of very high eroding velocities. The muds having good filtration characteristics deposited thin filter cakes at equilibrium circulating velocities well within tile range of those in a drilling well. It was observed that filter cakes deposited during stagnant filtration were quite difficult to erode by mud circulation. The - rate of crosion computed from the rate of filtrate accumulation after equilibrium cake thickness had been reached was in reasonable agreement with the rate of erosion obtained by direct observation. Continuous mud circulation usually caused the permeability of the filter cake to decrease with time. INTRODUCTION Many of the difficulties encountered during tile drilling of a well have been attributed to the loss of water from the mud and the attendant deposition of solids upon the walls of the hole. Past experience has shown that a reduction of the filtration rate of the drilling fluid eliminates or greatly reduces these difficulties. Definite filtration requirements, however, are hard to establish for a given set of conditions. This is due. in part, to the fact that the usual filtration test performed upon mud doe? not simulate well conditions as closely as desirable. The filtration characteristics of a mud are customarily determined by means of the standard low-pressure API wall-building tester.&apos; In this instrument a filter cake is deposited upon a horizontal bed under a pressure differential of 100 psi. The rnud is quiescent during the filtration period. In actual practice. mud filtration occurs within a well under quite different conditions. One of the major differences is that mud flows upward across the filter bed as the filter cake forms. This undoubtedly produces a change in the filter cake which cannot be reflected in the results of the API test. The laboratory work described in this paper had as its primary objective a better understanding of the influence of mud circulation upon the thickness and ,characteristics of the filter cakes deposited under conditions similar to those existing in a drilling well. ANALYSIS OF PROBLEM Once a permeable formation is penetrated by the bit, filtrate from the mud flows into the formation. &apos;he mud solids plaster against the walls of the hole, forming a filter cake. If the mud column is stagnant, that is, if it is not being circulated. the filter cake will increase in thickness until the hole is filled. Prior to the time that the hole is filled, the thickness of filter cake existing at any given time will be a function of the filtration characteristics of the mud, the temperature, and the pressure differential. The effects of these variables have been investigated in the past for both flat bed filtration2&apos;3 and for radial filtration.&apos; When the mud is circulated in a hole in which a filter cake i. being deposited. some of the solids that would ordinarily deposit in the filter cake will be carried away by the eroding action of the mud. This will limit. filter cake thickness. Some work has been done to determine the effect of flow upon the filtration rate in a circulating mud system&apos; but little work has been done upon the factors which determine the filter cake thickness existing in a circulating system. On first sight it would appear that the major factors controlling filter cake formation in a circulating system should be: 1. The rate of deposition of solids from the mud. 2. The erosive force that the flowing mud exerts upon the filter cake. &apos;A. The erodabilitv of the filter cake. 4. Any change in filter cake characteristics attributable to the scouring action of the mud. The rate at which solids are deposited from the mud will be controlled to a large degree by the filtration characteristics of the mud, the pressure differential. the temperature under

Jan 1, 1952

By S. L. Bessinger

Introduction In the design and specification of a ventilation system for an underground mine, it is necessary to make reasonably accurate estimates of the pressure losses in the various airways of the mine. These estimates can be made with little difficulty for open airways with simple geometric cross-sections, such as those cut by continuous miners or tunnel-boring machines. The situation is much different on a longwall face, where the airway&apos;s complex geometric cross section and the presence in the airway of obstructing equipment having a variety of shapes make it difficult, if not impossible, to estimate pressure loss using traditional methods of calculation. Head losses in mine entries are calculated using Atkinson&apos;s Equation. [22H= KPLQ (English) H= KP 3Q (SO (1) 5.2AA] where H = pressure loss, in. of H2O (Pa); K = friction factor, lbf•min2/ft4 (kg/m3); P = perimeter, ft (m); L = airway length, ft (m); Q = airflow quantity, ft3/min (m3/sec); and A = flow cross-sectional area, ft2 (m2) In this equation, the friction factor, K, is an empirical constant that describes the aerodynamic roughness of the airway. Typically, the K-factor for a given airway is determined by measuring the factors H, P, L, Q and A in Equation (1) and calculating K. Tables of friction factors calculated in this way are found in textbooks and handbooks that deal with mine ventilation analysis. Unfortunately, very few K-factors have been measured on longwall faces, and the accuracies of those that have been measured are entirely site specific, because of the wide variety of equipment found on longwalls. The development of a technique for prediction without mine-site measurements of the friction factor for any longwall face, regardless of its configuration, will thus be very useful in the design of ventilation systems for mines in which longwall mining is practiced. Calculation of pressure losses using Atkinson&apos;s Equation (1) and empirically determined K-factors provides accurate and useful approximations in cases where the airways have relatively simple cross sections. However, a careful analysis using the principles of fluid mechanics shows that such calculations are based on two assumptions that are not strictly correct when there are obstructions in the airway. The first assumption is that the air velocity distribution in the cross section, particularly around the perimeter, is uniform. This assumption results from the fact that the tabulated K-factor values found in the literature are based on field measurements with uniform conditions. Such uniformity does not exist in longwall airflows. The second common assumption is that the K-factor, and corresponding head loss, is independent of the Reynolds Number (NR) for a given flow. In fact, this assumption is not strictly correct, and is particularly erroneous in the case of irregular protuberances into the airflow, such as those found on a longwall face. The errors arising from the assumptions may be avoided by using K-factors calculated by a newly devised method, described below, which takes into account the fundamental principles of aerodynamic drag analysis. This new technique has two advantages: first, it is flexible enough to model any longwall, regardless of equipment configuration; second, it employs terminology and equations familiar to those who perform mine ventilation analysis, using K-factors, for which ventilation engineers have an intuitive understanding, rather than drag coefficients. To provide guidance for development of a longwall drag model, data were taken on two modern longwalls operating in substantially different conditions. Pressure measurements at Mine B were made with 200-foot (61-m) sections of 1/8-in. (3-mm) diameter plastic tubing, attached to a Dwyer Magnehelic gauge. Pressure drops were measured in 200-foot increments down the face, and summed to give the drop for the entire face length. This technique was found to produce small, repeated errors because of the number of segments required to span the longwall. At Mine A this problem was avoided by using a single, continuous, plastic tube for the entire face length. The psychrometric properties of the air were measured for both Mines A and B. A calibrated, standard vane-anemometer was used to measure the airflow on both faces. Finally, numerous dimensions were measured on both faces, and face profile drawings were obtained to allow detailed evaluation of the face equipment geometry. From this information, accurate evaluations of the average wetted perimeter and average area of the longwall face airways were made. Since the airflow is not confined to inside the powered supports at all points along the face, a quadratically weighted average of the airflows measured at various stations along the face was calculated: [n2Qavg =Qi Ii / It(2)i=1] where [Q, avg = average airflow for analytical purposes, ft3/min (m3/sec); Q= airflow at station i, ft3/min (m3/sec); 1= length of segment represented by Q, ft (m); h= length of longwall face, ft (m): and n= number of quantity measurement stations.] The quadratic weighting scheme was chosen because the

Jan 1, 1992

By A. S. Venkatadri, H. B. Bell

The equilibrium sulfur distribution between molten iron and Ca0-Mg0-Al203 slags containing iron oxide was investigated at 1550°C. The results were used to derive the iron oxide activities at low iron oxide concentrations in the slag by combining the sulfide capacity data obtained from gas-slag work with the free energies of both the sulfur solution in iron and the iron oxide formation in slag. The derived ferrous oxide activities were compared with values based on Tem-kin&apos;s kin&apos;s and Flood&apos;s ionic models. One difficulty in using these models is that the nature of the aluminate ion in slag is uncertain. Nevertheless, such indirect methods, in particular, those described in the present paper, are of value because of the difficulty of measuring small amounts of oxygen in liquid iron in equilibrium with slag. It is shown that these methods confirm the consistency of thermodynamics data on liquid iron and slags. It is well established that decreasing the iron oxide activity in the slag increases the desulfurization of molten iron at constant slag basicity. This effect is most pronounced at the very low iron oxide activities, characteristic of blast furnace slags. Yet a precise quantitative determination of the significance of low iron oxide contents in slag in blast furnace desulfuri-zation is not possible for the following reasons: a) difficulty of separation of iron "shots" from the slag, and b) errors in chemical analysis of small amounts of iron oxide in slags. In view of these obstacles, one must resort to indirect methods of calculating iron oxide activities. EXPERIMENTAL TECHNIQUE The apparatus for providing the sulfur equilibrium data has been described previously1 and was similar to that used by ell&apos; in connection with the study of slag-metal manganese equilibrium. The procedure consisted of: a) melting about 50 g of Armco iron in a magnesia crucible in a platinum furnace, b) adding a mixture of about 15 g of lime-alumina slag and varying amounts of Fe2O3 and CaS, and c) maintaining the temperature at 1550°C for more than an hour in an atmosphere of argon to enable the sulfur equilibrium to be attained. Several melts were made using lime-alumina slags with basic composition 55, 50, and 45 pct lime. During the experiment the temperature was controlled manually using a Pt/10 pet Rh-Pt thermocouple. After the experiment, the Power was shut off and the flow rate of argon was increased to freeze the melt as quickly as possible. The analysis of sulfur in the metal was carried out by the oxygen combustion method3 using uniform drillings from the top and bottom of the metal button. After crushing and grinding and removal of any iron particles with the aid of a hand magnet, the slag was analyzed for sulfur by the CO2 combustion method.4 The E.D.T.A. method was employed for the analysis of lime5,6 and magnesia,= the ceric sulfate method7 for the analysis of slag iron oxide, and the perchloric acid dehydration method5 for the analysis of silica. The remaining amount was taken to be Al2O3 precipitation with ammonium hydroxide in several preliminary melts had confirmed the propriety of using this simple procedure. RESULTS The activity of iron oxide in binary, ternary, and more complex slags has been the object of numerous investigations, and the two experimental methods for its determination are: 1) Equilibrating the metal with the slag in question and measuring the oxygen content of the metal. The ferrous oxide activity is then given by aFeO L%OJSat where [%0]sat is the oxygen content of the metal in equilibrium with pure iron oxide slag. This method was used by Chipman et al.8,9 2) Equilibrating the slag in iron crucibles with known partial pressures of H2/H2O or CO/CO2 mix-tures.10-12 This method is limited to temperatures between 1265" and 1500°C. The very low oxygen content of the melts in this investigation made it impossible to derive the ferrous oxide activity by the first of these methods. Therefore, the iron oxide activities were computed by means of: Sulfide capacity data from the gas-slag work" Temkin&apos;s concept14 Flood&apos;s approach15 a FeO from Sulfide Capacity. The method of calculating the aFeO involves the sulfide capacity of the slag (c,), the sulfur distribution coefficient (Ls), the free energy of dissolution of sulfur in iron, and the free energy of formation of iron oxide in the slag. Bell and Kalyanram13 have investigated the sulfur absorption characteristics of lime-alumina slags containing magnesia by the Carter-Macfarlane method16 (based on comparing the sulfide capacity of the slag in question with that of a standard slag of unit lime activity) and have derived lime activity values. The relation between sulfide capacity and their lime activity a&apos;CaO is given by: Cs= 3—: Xa&apos;CaO at 1500°C

Jan 1, 1970