Search Documents

By Mario Mauro, Jeff Taylor, Carlos Morales

"In 2007 the US Army Corps of Engineers classified the Herbert Hoover Dike in Florida as a Dam Safety Action Classification (DSAC) 1 dam, and started the implementation of one of the largest dam rehabilitation projects in the nation. The construction of the cutoff wall is a key feature of this rehabilitation work to upgrade the dike to current dam safety criteria. The cutoff wall installation is currently being completed on Reach 1, which extends from Port Mayaca to Belle Glade, under a Multiple Task Order Contract based on performance specifications and stringent verification criteria.For the construction of the cutoff wall TREVIICOS selected the self-hardening slurry method. Since the cutoff wall is installed through a layer of highly variable limestone with Unconfined Compressive Strength (UCS) up to 14,000 psi, the excavation requires the use of the hydromill equipment. This is the first successful application of the hydromill technology with self-hardening slurry in a large scale project in the US. This paper presents the details of the method utilized, the quality control procedures, and the experience gained over seven miles of cutoff wall installed.INTRODUCTIONProject LocationThe Herbert Hoover Dike (HHD) system, around Lake Okeechobee in South Florida, consists of a series of levees, culverts and locks and is approximately 143 miles long (Figure 1).Lake Okeechobee is the second largest freshwater lake in the lower 48 states of the United States. The lake is the primary drinking water source for numerous communities around the lake and to millions of people living along the lower east coast. The lake is also a vital source of irrigation for the agricultural industry in the South Florida region.Lake Okeechobee is 33 miles wide from north to south and 30 miles wide from east to west and has a surface area of 730 square miles. The average water depth of the lake is 9 ft."

Jan 1, 2017

By Mario Mauro

In 2007 the US Army Corps of Engineers classified the Herbert Hoover Dike in Florida as a Dam Safety Action Classification (DSAC) 1 dam, and started the implementation of one of the largest dam rehabilitation projects in the nation. The construction of the cutoff wall is a key feature of this rehabilitation work to upgrade the dike to current dam safety criteria. The cutoff wall installation is currently being completed on Reach 1, which extends from Port Mayaca to Belle Glade, under a Multiple Task Order Contract based on performance specifications and stringent verification criteria. For the construction of the cutoff wall TREVIICOS selected the self-hardening slurry method. Since the cutoff wall is installed through a layer of highly variable limestone with Unconfined Compressive Strength (UCS) up to 14,000 psi, the excavation requires the use of the hydromill equipment. This is the first successful application of the hydromill technology with self-hardening slurry in a large scale project in the US. This paper presents the details of the method utilized, the quality control procedures, and the experience gained over seven miles of cutoff wall installed.

By Zia Zafir

"Levees in the central valley of California are primarily for flood control purposes and thus are subjected to infrequent hydraulic loading. The primary concern for these levees is their instability due to through and under seepage. Primary seepage control measures are seepage cutoff walls and/or seepage berms. The cutoff walls primarily consist of soil-bentonite (SB) slurry walls. The seepage berm could be a drainage blanket to allow the seepage with controlled exit gradient or an impervious layer to provide enough cover to protect any adverse effects of seepage in terms of sand boils. Although, Sacramento is an area of moderate seismic activity, levees protecting urban areas require assessment for the potential instability due to liquefaction and associated vertical and lateral deformations. In certain cases, the seismic deformations of the levee may not compromise the stability of the levees, but they may cause damage to the seepage control measures. Depending on the nature and extent of the damage, the mitigation measures may require limited or full replacement of the seepage control measures. This paper will provide a systematic assessment of these different types of seepage control measures under vertical and lateral deformations due to liquefaction and lateral spreading under seismic loadings.INTRODUCTIONThere are two broad categories of levees in Central California: levees that are subjected to continuous hydraulic loading such as delta levees and are called frequently loaded levees (FLL) and flood control levees that are subjected to seasonal or infrequent hydraulic loading, called infrequently loaded levees (ILL). This paper will focus on the seismic response of ILL. The probability of ILL experiencing an earthquake at the time of the design flood is very low. Therefore, consequences of seismic failure of flood control levees are only significant in terms of response time required to restore the level of flood protection provided by the levee before the next flood season. An example for this restoration is the restoration of the Pajaro River levees in Santa Cruz, California after the 1989 Loma Prieta Earthquake. Nevertheless, failure of flood control levees due to a seismic event could result in loss of the entire levee and/or loss of freeboard. In addition, some of the seismic failure of ILL levees may result in loss of seepage control measures such as the soil-bentonite wall.The State of California State approved Senate Bill (SB) 5 in 2007 that mandates for 200-year flood protection to be the minimum level of protection for urban and urbanizing areas in Central California (Sacramento-San Joaquin Valley) by the year 2025. This legislation also requires that urban and urbanizing areas protected by Federal project levees cannot use adequate progress as a condition to approve development after 2025. SB 5 requires that the urban level of flood protection be consistent with criteria used or developed by DWR (Government Code § 65007(k)). To avoid delaying urgently needed flood protection, Urban Levee Design Criteria (ULDC, 2012) was developed."

Jan 1, 2016

By R. Kumar, N. R. Mandre

"The beneficiation of iron ore slimes by selective flocculation was studied. Polyacrylamide (PAM) and guar gum were used as flocculant, along with sodium hexametaphosphate (SHMP) as a dispersant. The samples collected were initially subjected for chemical and mineralogical studies. The mineralogical studies indicated the presence of haematite and goethite as the principal iron-bearing minerals, with quartz and kaolinite as gangue minerals. The selective flocculation tests showed that the Fe grade can be enhanced from 58.24% to 64.60% Fe at a recovery of 66.33% using polyacrylamide as the flocculant. A Fe grade of 63.20% at a recovery of 68.04% was obtained using guar gum as flocculant. The efficacy of the studies was analysed using a separation index, which indicated that the higher separation index was obtained with the tests employing polyacrylamide as the flocculant. IntroductionIndia is endowed with huge reserves of highgrade iron ore and is one of the prominent producers in the world. As the high-grade iron ores have been exhaustively mined, it has become imperative to use low-grade iron ores, fines, and slimes to meet the growing demand. Also, generation of fines and slimes during mining and processing contributes to loss of minerals to the extent of 30% of the total value (Mandre and Panigrahi, 1997). These fines/slimes are often discarded as waste into tailing ponds, containing considerable amounts of iron. Therefore beneficiation of tailings/slimes has become necessary for optimal utilization of the resources.In recent years, interest in recovery of valuable minerals from low-grade ores, slimes, and tailings has increased worldwide. These activities are initiated not only to recover minerals but also to address various environmental issues associated with fine particle treatment. The literature reveals that several technologies have been employed in this regard, including flotation, advanced gravity separation, and high-intensity magnetic separation. However, these processes are found to be ineffective for fine particle treatment due to lower collision probability in flotation, decreased gravitational effect in gravity separation, and reduced drag force in magnetic separation, among other factors (Batisteli and Peres, 2008; Das et al., 2007; Dworzanowski, 2012; Rocha, Caneado, and Peres, 2010). Therefore, it is in this regard that selective flocculation has gained importance in treating slimes in recent years."

Jan 1, 2017

By Roger Favreau, Patrice Favreau

The article reviews the aspects which contribute to the quality of the results from a blast with explosives, namely a good floor, no large blocks, easy mucking, and explains the mechanisms of the blasting process which decide on the quality of these aspects for a given blast method, and how these mechanisms can be simulated from basic principles. It proposes that good fragmentation size distribution can also be important if the rock is going to a crusher, e. g. for the ore in a mine and for the rock excavated in a quarry.

Jan 1, 2012

By Stephen C. Britten

An in-situ amperometric slag sensor for measuring the concentration of easily dissociable oxides in slags at temperatures between 1200-1600°C is being developed. The sensor provides the same information as potentiometric sensors while also providing data on the concentration of the transition metal species and the diffision kinetics within the slag. The electrochemical technique utilized in the sensor is similar to methods utilized in aqueous voltammetry.

Jan 1, 1998

By Manuel S. Rivera

Abstract. Instrumentation in concentrators has evolved from a few isolated indicators to compu- terized control within twenty years. This evo- lution has caused a drastic change in the phil- osophy, personnel and equipment used in a pro- gram of servicing and utilization of present day automation.

Jan 1, 1980

By Robert Hopler

Your petitioner further alleges that at various times, to wit, from 1872 until June 30, 1895, during the existence of the combination and conspiracy in restraint of trade among the various States herein- before described, there were organized under the laws of various of the several States of the Union various corporations having for their object the manufacture and shipment and sale of a high explosive commonly known as dynamite, which said explosive is commonly used for the same purposes as those for which blasting powder is used;

Jan 1, 2013

By Joshua Micah Hoffman

While it is easy to state that meaningful involvement of the community can play a critical role for a successful blasting operation, following through with this involvement is not an easy task. Structured Public Involvement (SPI) is a developed protocol for involving communities in project planning decisions and could be readily applied to the blasting industry. SPI was developed for the purpose of collecting quality public input about public transportation projects. The purpose of SPI is to bring about stakeholder satisfaction with potential projects by allowing controlled input from the stakeholders. It was designed and intended for democratic societies that have come to expect a voice in public projects. While blasting operations are not always in the domain of public projects, the fundamental process outlined by SPI can be useful for collecting feedback from the immediate public around blasting operations.

Jan 1, 2014

By J. E. Wey

Extraction of cobalt from cobalt sulfide and cobaltite flotation concentrate from the Blackbird Mine, Idaho, was investigated using an adapted strain of Thiobacillus ferrooxidans. Cobalt extractions as high as 100% were realized in the inoculated experiments, whereas only 4% extraction was obtained in the sterile run. The influence of pulp density on the rate and extent of cobalt extraction was also determined. It was found that the extraction of cobalt followed predominantly the indirect mode of bacterial activity. In this process, ferric iron oxidizes cobaltite to cobalt sulfate and ferric arsenate while being reduced to its ferrous state; the bacteria continuously re-oxidize ferrous to ferric iron. Electrochemical measurements using cyclic voltammetry suggested that cobaltite oxidation involved a number of intermediate reactions.

Jan 1, 1993

By F. Rashchi, N. Naseri Joda

Recycling of electronic wastes is an important subject both from an environmental point of view and also the recovery of valuable materials. In this research, PC board scraps were leached to recover Cu, Ag, Au and Pd. Due to the high cost of the shredding process and to avoid secondary pollution from odors and dusts, board scraps were cut into 5X5 cm2 pieces. To determine the most effective leachant, aqua regia, nitric acid, hydrochloric acid, ammonium persulfate and potassium persulfate were tested. The effect of the leaching parameters, the leachant concentration, temperature, leaching time and liquid to solid ratio were studied and optimized using response surface methodology.

Jan 1, 2011

By D L. Kennedy

It has always been a challenge to accelerate the underground development progress by increasing the advance rate of each development round. Surveys have shown that most of the development rounds have only been pulled 84 per cent to 94 per cent of the drilled length. Where bare detonators have been used as primers, less advance rate is expected. In order to obtain a good understanding of the influence of priming upon the advance rate in underground development, a series of high energy primer trials has been conducted by Orica Explosives in the goldfields using various types of Orica high energy Anzomex « primers. It has been shown that development face has been pulled an extra 140 mm to 420 mm by priming with Anzomex « K primers compared with conventional primers. From all the trials at different sites, we have seen that the face pulled using K primers was more square than that pulled using conventional primers. Virtually, no butts and toe were left on the face developed using K primers. Computer simulation has been conducted using either a conventional primer, a bare detonator or a K primer as initiator. The study compared the predicted crack patterns developed around the toe of the hole and it was deducted that a detonator-initiated hole would leave a butt some 200 mm longer than that from a conventional primer-initiated hole, and a K primer-initiated blasthole would give rise to stronger initial p-wave, promoting crack development around the toe and increasing the ability to pull close to the full depth.

Jan 1, 1999

By K. Hori

In this study, the determination of optimal conditions for jig separation has been investigated with a TACUB jig separator. The TACUB jig, from which a Batac jig originated, is a useful gravity separator that is effective to separate crushed solid wastes as well as coarse ores. A mixture of crushed polyethylene (specific gravity 1.3) and polyvinyl chloride (specific gravity 1.5) was separated by a batch TACUB jig by varying the frequency (wavelength) and the amplitude (pulse stroke length). It was found that the sample particle layer in the separation chamber was fluidized without turbulence by the rising water pulse resulting in the separation. However, a too strong water pulse reduced the efficiency of the separation of the particles. The results indicate that the specific velocity of the rising water is necessary to fluidize the particle layer without turbulence to separate the particles. The expansion ratios of the thickness of the particle layer in rising flows were measured in a cylindrical column. The pressure losses by the particle layer were calculated from the expansion ratios and the velocity of the rising flows by Ergun?s equation. The curve of the pressure loss vs. the velocity of rising flow showed a maximum point corresponded to the point of fluidization. The velocity of a rising flow on the point of fluidization provided the optimal separation condition.

Jan 1, 2014

By D. Duvris

The main objective of this work was to quantitatively investigate exhaust emission levels, as related to maintenance (service) intervals, during the operation of diesel-powered equipment at an underground bauxite mine in Greece. Such emissions depend on a great number of parameters, including the type (technology) and tuning of the engine, the type of work performed as related to the engine workload, suggested maintenance intervals, the altitude, the temperature and the humidity of the atmosphere of the underground mine, the properties of the fuel, the operator's training and experience level. Necessary ventilation quantities were calculated based on exhaust gas concentration measurements, site specific relationships between pollutants and adjusted air quality indices. Diagrams comparing necessary and recommended air flow for several equipment groups featuring two engine types and for different maintenance intervals are presented.

Jan 1, 1998

By P Valenzuela

Joint mapping is a fundamental input for rock mass characterisation and slope stability analysis. The usual way to do it is using a compass in the field or digitising structures on a screen, with a software package.In this paper a method to identify and map joints automatically along a rock face is presented; it is called the Concentric Shells (CS) algorithm. The method scans a point cloud sequentially, tests if selected points are ‘true pivots’ within an inner shell, and then it searches for points inside a wider sphere (outer shell).The algorithm, developed by the author, was applied in real data. It reproduces the main features obtained from conventional (compass) and digital mapping (software package). Execution times are approximately 45 seconds for two point sets holding of 3.1 million points. Obtaining the same results via digital mapping takes approximately 3–4 working days.Key advantages of this method are: significant time reductions; elimination of mapping bias; and the ability to manage very large data sets (>2 million points) without the need of scanning the cloud on the screen. These advantages make this method an attractive tool for engineers and geologists wanting to increase productivity.CITATION:Valenzuela, P, 2017. Automated joint mapping using the concentric shells algorithm, in Proceedings Tenth International Mining Geology Conference 2017, pp 257–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By K Cochrane

Time and time again history shows us that mine closures are sustainability failures. Mine operators do not know how to turn the mine closure into an asset and communities around the mine do not know how to plan or what to implement to be sustainable when the mine needs to close. If we want to achieve sustainability when we close a mine, we generally need to consider what economic activity we will have to create leading up to the mine closure to ensure that the communities remaining in the area are not worse off after mining than before. There is not one silver bullet solution to mine closure, as all mines are affected by different environmental and socio-economic conditions. That is one of the reasons why mine closure is so difficult.Effective stakeholder engagement is the nucleus around which sustainability is built. Achieving sustainability as part of mine closure means not only a self-sufficient community, but also could lead to transformation of that asset.A key issue is that neighbouring communities become completely reliant on the mine. The mine has influenced the economic, environmental and social aspects of the community and with no alternative economic sources. The community and municipality will struggle with capacity to maintain infrastructure, services and jobs. This not only impacts the mine workers and their families but also other businesses and people in the town that make a living by servicing the needs of the workers and their families. Social problems associated with a mining operations and closures need to be considered. The misuse of alcohol, domestic violence, breakdown in law and order, economic and health issues all have a severe influence. Families often need to relocate from the mining town to find work. This further perpetuates the impact of the mine closure to the economic viability of the town. CITATION:Cochrane, K, 2018. Is your mine closure a sustainability failure? Transform your asset and create a self supporting neighbouring community. It’s as easy as ABCD!, in Proceedings Life-of-Mine 2018, pp 38–42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By R. E. Williams

University of Idaho scientists research under U.S. Bureau of Mines Cooperative Agreement C0278001 constitutes a complex hydrogeological, hydrochemical and metallurgical mine waste management project at an existing Superfund site. Technologies that may prove useful for the extraction of dissolved metals from acid mine water and solid wastes include lixiviation and biosorption. Acid mine water is the major, long-term problem in the valley. We are attempting to delineate the major sources of ground water recharge which feed the acid mine drainage and their hydraulic properties. Grouting of recharge areas may facilitate minimizing the production of acid mine drainage if recharge pathways can be identified.

Jan 1, 1990

By Bryon Cerklefskie, Michael Schulte

"This case study explores the usage of polymer ducting as a replacement to curtains and FRP for face ventilation in two coal mines. There are two mines looked at, one is the highest elevation underground coal mine in North America, the other is the gassiest mine in North America. The paper details the trials of both mines switching from FRP and curtain respectively to polymer ducting. The results discuss the ability for the mines to not only achieve consistent airflows and keep them in compliance but the unexpected positives. Mine A was allowed to do longer cross cuts due to increased air volume at the face. This drastically cut their costs of mining down due solely to modification of the ventilation cycle. Mine B saw economic benefits due to longer cuts between place changes. Both mines have documented lower dust, methane, noise, and improved wear and tear on their equipment as a result.INTRODUCTIONThe emergence of longwall mining in underground coal operations has resulted in new ventilation challenges. Numerous production crews strive to complete their development sections with enough time to adequately prepare for the upcoming longwall panel. Continuous miners will cut out two or three entry development sections per their ventilation plan, that is approved and controlled by MSHA (Mine Safety and Health Administration), which will drive amount of footage that can be mined at a time prior to installing roof support. At this moment the continuous miner, hereafter referred to as the CM, will back out of the entry and moves to the second entry to complete a similar cut. Typically, a roof bolter crew will pull in to the finished cut section and install ground support. This is called a place change style of production coal mining. There is an alternate method that includes a miner/bolter combination as well but that was not featured at either test site in this case study. Ventilation has to be provided to sweep the working face of each entry to control dust and gasses. Each task will have an MSHA prescribed ventilation requirement dependent on the dust levels and methane emissions of the rock for that particular mine. The CM, roof bolting and unused headings will each require constant ventilation but at different volumes. Since each working face is changing throughout the mining cycle the ventilation requirement in a working heading is never static and is changing with the working task.Traditional Ventilation ControlsTraditionally face ventilation for coal mining operations has been completed thru the usage of a curtain system and\or using auxiliary fans and ventilation tubing. Room and pillar mining systems typically utilize curtain systems, which use curtain walls that are installed by the miners by erecting wood framing and covering it with brattice curtain. This splits the drift width to allow fresh air to sweep the face and take the contaminated air and dust behind the curtain to the ventilation exhaust\return area of the mine. This method is difficult to adjust the airflow from entry to entry during changing cycles and requires that a wider drift is mined out in order to have enough room for the brattice wall. In operations that require roof bolting, this method limits the length of the cuts from the CM prior to advancing and can lead to not providing enough ventilation to keep dust and methane levels below compliance requirements."

Jan 1, 2019

By H. Ishimoto

It always has been a serious issue to improve safety in mine sites, demolition work sites, and civil engineering work sites. Especially, collision accidents caused by construction equipment damage not only the productivity of operations but also the health and life of workers in those work sites. To solve this problem, a variety of worker auto-detection means are developed so far, but they have not still become widely used in actual worksites. There have been two controversial points in the prior methods. One is that they were not enough in respect of the detection accuracy and certainty, and the other one is that the information of the detection results was not comprehensible to the operator of equipment. In this paper, the functional requirements of the obstacle detection system in earth moving work site is redefined at first, and then, it is proposed to apply a stereo vision to the obstacle detection system for an excavator. The system consists of horizontally arrayed two digital cameras with low distortion lens, an image processing controller, and a monitor for an operator in the cab. Stereo vision calculates the depth image from images of two cameras and detects the presence of obstacles, its distance, direction, and dimensions. Sensed obstacles are informed to the operator in the monitor image. Preliminary experiments are conducted with a stereo vision system mounted on a real equipment in a demonstration site. The result shows that two controversial points of the conventional technologies are improved, and that the applicability of this system is validated.

Aug 1, 2013

By Enrique Monge

Dado que a nivel universitario existen pocos laboratorios adecuados de Física y Química en el Perú, se ha desarrollado proyectos de laboratorios privados y plantas experimentales tanto en el campo analítico y metalúrgico que encauzen la industria minera por el sendero de la técnica más elemental. En ese sentido, el presente texto señala la importancia de los laboratorios de investigación para las industrias mineras y metalúrgicas a través de la Universidad Nacional de Ingeniería y el apoyo del Estado. El laboratorio está dividido en 6 secciones: Minería, preparación y concentración de minerales; metalurgia de minerales no Ferrosos; carbón; fierro y acero; metales y aleaciones.

Jan 1, 1959