Search Documents

By M. -H. Fillion

"Geotechnical stability analysis and design in open pit mines requires access to representative geological, structural, hydrogeological, and rock mass models. The quality and quantity of collected geomechanical data used to build such models can have significant implications in the design of safe and economically viable slopes. Data collection is a continuous process throughout the life of a mine. The process starts from exploration to conceptual/preliminary feasibility, feasibility, design and construction, operations (early production/late production), and mine closure.As geomechanical data is often limited at an early stage of a project, the estimated variability of the geotechnical factors may be larger than the actual data variability. This can potentially result in a conservative selection of the pit slope angle. Collecting additional geomechanical data at later stages of the mine development may contribute to reducing the uncertainty associated with the geotechnical properties and a steeper slope angle may be used for the design. This can result in significant economic benefits.This paper investigates the impact of access to new data over time, following a series of geomechanical data collection campaigns, on design decisions. This is illustrated by comparing the resulting slope design, at three stages of the mine project, at a South African open pit mine. To demonstrate this, a series of slope stability analyses were performed using limit equilibrium tools. For each project stage, the slope angle design was modified until a similar probability of failure of 5% or less was obtained. The corresponding factor of safety distributions for each project stage were then compared to evaluate the impact of collecting additional data on the resulting slope design.The results showed that data variability can differ significantly from one project stage to another. Data variability may be greater at more advanced project stages (i.e. a wider distribution of the factor of safety). Furthermore, the results showed that, even for the cases with greater variability, steeper slope angles were possible at more advanced stages for the proposed design requirement (probability of failure < 5%). In this investigation, as more data became available, the uncertainty associated with data variability could be sufficiently reduced to allow the selection of less conservative slope angles. This can be used as a managerial tool in developing data collection strategies and allocating the necessary funds, and can lead to important economic benefits to the mining operation."

Jan 1, 2016

By R. W. Titshall

WHAT IS SAMPLING? We are all involved in sampling almost every day of our lives, by tasting, feeling, or smelling. Most raw materials, food products or manufactured items are sampled several times at various stages of the production process before a commodity of suitable quality can be produced. Data obtained from sampling is used in establishing price, quality control, allocating production costs, or overall process efficiency. The area of sampling outlined in this article is the collection of a small quantity of material from large continuous bulk flows of solids and slurries. The concern in obtaining the sample is that the material obtained is truly representative of the main flow in every respect. The methods and equipment outlined are for the collection of a manageable sample. The sample has to be analyzed in a laboratory to determine its characteristics and compliance to set standards. SELECTING A SAMPLING SYSTEM When selecting a sampling system, it is essential to define the requirements, as to what the actual sample obtained will be used for and what degree of precision is required. Determine whether or not the system has to comply with any set standards such as A.S.T.M. (American Society for Testing and Materials) which have established methods for collection of a gross sample of coal. Sampling which is done for in-plant or process control is not generally governed by set procedures, but similar care should be taken during the selection process so that when the equipment is put into service it will operate reliably and produce a sample which is truly representative of the total material lot or consignment.

Jan 1, 1982

By N. Tounsi

The use of analytical modeling of continuous chip formation in conjunction with orthogonal cutting experiments was presented in the open literature to identify the coefficients of material constitutive equation within the practical range of stress, strain, strain rate, and temperature encountered in metal cutting. Identification of reliable constitutive data was hampered by a lack of a reliable model for the prediction of the primary shear zone thickness that affects directly the effective strain rate field. An original analytical model to determine the primary shear zone thickness is proposed in this paper. It is based on the mechanics governing the material flow in the primary shear zone. Based on the distribution of the hydrostatic pressure and the forces measured from orthogonal cutting tests, the model that describes the thickness of the primary shear zone is derived. To validate the model, FE simulations of chip formation using DEFORM3D were carried out for different materials and cutting conditions. The results of the analytical model are in reasonable agreement with FEM results.

Jan 1, 2006

By D. Emadi

The ASTM B108 Mould and a Modified Mould were used to cast test bars under a variety of conditions: mould and pouring temperatures, mould coating and tilt. Mechanical properties were determined in the as-cast and heat-treated conditions. The ASTM Mould is less sensitive to casting variables. Enlarging the gating system and adding additional gates to the ASTM mould can improve properties in the tilt position. The reproducibility of properties in as-cast and T6 heat treated bars was investigated.

Jan 1, 2004

By W. W. Agey

Past investigations on waterborne impurities in the flotation process have been concerned primarily with the treatment of specific ores with particular local waters. Although some anions and cations present in water are known to react with flotation reagents, a definitive study has not been made on the effect of such common ions upon the flotation process. This report describes the fundamental research undertaken to define and measure the adverse and/or beneficial effects of different concentrations and combinations of several common anions and cations when oleic acid is used to froth-float limestone from a pulp of quartz and limestone. Research on the effect of waterborne impurities upon the flotation process was composed of two equally important phases. The first phase comprised development of a procedure for floating limestone from quartz that would give the same results in test after test. Some difficulty was encountered, but once such a procedure was developed, the second phase, comprising study and measurement of the effect of various ions c on to natural water upon the flotation of limestone, was quickly completed.

Jan 1, 1963

By M. J. Lempel

A theoretical study of the heat-transfer characteristics of a dilute gas-solids mixture in an externally heated tube is reported. Detailed equations are developed describing the system, and a numerical method is presented to solve the equations using a digital computer. The methods are applied to a system containing fine coal particles entrained in hydrogen, flowing through a hot tube. Heat-transfer coefficients and several other physical constants are evaluated in detail.

Jan 1, 1967

By Rolf A. Knopp

This paper discusses how design differences in FLP diesel equipment in underground coal mines came about. "Design standards" tend to create differences between countries while fostering uniformity among products of competing manufacturers. "Performance requirements," on the other hand, tend to eliminate differences between countries while encouraging competitive development of better products. Examples of regulations from the U.S., Canada. Great Britain. Australia. South Africa, etc., are used to illustrate differences in the design and certification of diesel equipment for underground coal mines.

Jan 1, 1978

By R. W. O. Kersten

"The aim was to investigate stable pillar design procedures currently in use on chrome and platinum mines, subject them to a critical appraisal, and review some of the alternatives proposed in the literature. It is concluded that these pillar design methodologies suffer from drawbacks that can be detrimental to the mining industry and that an improvement is essential.It was decided that the increased availability of analytical models and failure criteria could be exploited to update the empirical to an analytical/empirical method. The proposed methodology adopted FLAC2D simulations using the Hoek-Brown failure criterion to calculate full stress-deformation curves for typical pillars. The mine stiffness concept was introduced to determine the pillar load, integrating the influence of the pillar and strata stiffness and mining geometry.The proposed methodology was calibrated by comparing experimental and predicted deformations and failure depth of pillars in one hard-rock mine. The conclusion was that the methodology is an improvement over the one currently in use. An improved factor of safety is given by the intersection point of curves for the stiffness of the system and the pillar strength. IntroductionThe paper describes part of the findings of a PhD thesis (Kersten, 2016) on an alternative stable pillar design methodology. This publication contains sufficient information to implement the method for further interpretation and testing. A detailed comparison of measured and predicted data is dealt with in the thesis, and the results show that there is promise in the methodology.The design of stable pillars in mining is of fundamental importance, not only in the Bushveld Complex mines but throughout the mining industry. Wherever mining occurs, pillars are formed at some stage and it is essential to predict their behaviour, i.e. whether they will burst, yield, or remain stable. Although of crucial importance, pillar design still suffers from major shortcomings and weaknesses."

May 1, 2019

By Atulya Verma, Samantha Espley, Nashel Kalaka

Numerical modelling simulations of proposed mining sequences are used to evaluate mining induced stress concentrations and their migration associated with the progress of mining. This analysis is a standard practice for most prospective mining projects at various levels of feasibility study. The studies are usually initiated at the beginning of the mining cycle, on a global scale, and are maintained and updated throughout the life of mine (LoM) to identify or address local issues and the required remedies as and when needed. Developments in numerical modeling techniques along with advancements in computing technology and data storage/management capacity have given rock engineers access to a huge volume of data that needs to be analyzed and assessed. The most common approach to numerically evaluate stress concentrations and migrations in underground mines is to select the points of interest in a given volume such as the back of an excavation or points within pillars around critical infrastructure, and plot the stresses or a derivative of stresses over time to represent life of mine concentrations and migrations of stresses. The problem with this approach is the sharp gradient of stresses close to excavation boundaries. Slight changes in the location of selected points can change the stress concentration and migration patterns substantially and all generalized statements about LoM risk can be challenged in one way or another. For global stresses, the most common current approach of data analysis is by viewing series of pictures representing stress contours. In this approach, it is easy to overlook some critical detail and/or be masked by personal preferences of contour/picture representation. To overcome the problem of representing and analyzing huge volume of stress simulation data, the authors, through their experience at different mining operations, developed a volume-based technique to reliably evaluate mining-induced stress concentrations and migrations. The volume-based approach is for risk-based assessments of adjacent regions in the rockmass, in and around planned stoping excavations. The volume of interest is the entire ore body that is planned to be mined, but it could be just a part of the ore body depending on the specific use case. The risk identifiers are the induced stresses as compared to the strength of the rockmass. Over the LoM, the risk identifiers are tracked versus the corresponding excavation ratio of the zone. This approach is very effective in identifying the stages of mining that are contributing the most to the mining induced stress risk and the results can be used for proactive planning and mitigations measures such as alternative mining sequences, or stope sizes, or extraction methods. The approach has also been very successful in application at mature mines, particularly in assessing the re-initiation of mining in zone that has been dormant for some time. The volume-based approach allows for an assessment of the current state of the rockmass and the identification of future risks when planning resumption of mining activities.

Jan 1, 2023

By Edwin B. Wilson

The purpose of the panel&apos;s examination of coal mining research and development is to explore how the various groups that make up this research community might work together more efficiently and be more productive. The community, as defined here, includes federal and state governments, coal producers, manufacturers, unions, universities, and industry sponsored research organizations. The framework chosen for these discussions consists of brief presentations by the panel members on their views of the proper role and function of the group they represent. The panel members were also asked to highlight the economic, technical and institutional constraints that affect the performance of research and development and the use of the results. Following these presentations, a number of prepared questions will be discussed by the panel, and audience participation is invited. These questions were given several weeks ago to the panel members for their study. Before proceeding with the panel member reports, a brief review of the importance of R&D to the coal mining industry would be helpful to setting the stage for a constructive dialogue. It is appropriate to begin this review by mentioning that there is complete agreement among the research community that the major goals are: Improve health and safety Protect the environment Increase capital and labor productivity Increase resource recovery Since the basic functions of the academic, industrial and government sectors are different, we should expect that the research and development objectives and priorities, roles and responsibilities under each major goal will be different for each research group. The differences do not represent problem areas. However, problems will arise if the objectives are not properly interfaced at the appropriate time. The consequences of railing to understand the need for integrated programs will be the classic result, best described by the phrase --"a technical success but a commercial failure."

Jan 1, 1978

By Stefan Larsson, Jan Ekström, Jennie Kock-Larsen, Håkan Garin

"This paper describes the testing procedure (or protocols) for quality control of dry deep mixing columns in a major ground improvement project carried out in Sweden. Quality control was mainly based on column penetration tests performed at different stages in the project and on two occasions after installation. In the paper, the results from the tests are compared with tests on the unimproved clay. As expected, the results show that the correlation between undrained shear strength in the columns and in the unimproved soft soil depends mainly on the in-situ stress. However, the correlation probably depends on when the tests were performed after mixing. When the influence of the in-situ stress was excluded from the analysis, no significant correlation could be identified. This means that the undrained shear strength in the columns and in the unimproved soft can be considered to be uncorrelated when the strengths and the corresponding variability are evaluated with depth from groups of tests.INTRODUCTIONQuality control and quality assessment of deep mixing (QC/QA) constitute a key component in verification of the limit state design. Due to the complex mixing process and varying geological conditions, it is normally not possible to sufficiently assess the strength and deformation properties in advance. In Sweden, the most commonly used QC/QA method for verification of the limit state is the column penetration test (Axelsson and Larsson 2003; Bergman et al. 2013). The method works well but is time-consuming and requires many tests since property variability is normally high. The column penetration test can be used to assess the undrained shear strength Cu,col. However, it is not clear how the strength correlates to the undrained shear strength of the unimproved soil Cu,soil. There are common factors such as the in-situ stress state and the natural water content, which makes a positive correlation probable, i.e. as Cu,soil decreases, Cu,col also decreases and vice versa. The unimproved soil has a natural spatial variability, but it is not known if the improved soil follows the same variation. The mixing process has a substantial influence on the strength variability and may supersede the influence of other factors. However, if a sufficiently good correlation exists between Cu,col and Cu,soil, information from the geotechnical ground investigations can be used in the design and planning of QC/QA of deep mixing in a more stringent manner. Information about the correlation is also essential in reliability based design, where a strong positive correlation may have a negative influence on reliability. However, as discussed by Al-Naqshabandy and Larsson (2013), this correlation may be weak or insignificant for a representative failure domain where the mixing process may have a dominant influence on the strength variability. It is thus of interest to assess the correlation."

Jan 1, 2015

By Marco Arratia H.

Las etapas iniciales de la ingeniería de un proyecto comprende: los estudios de perfil, prefactibilidad (ingenieria conceptual) y factibilidad (ingeniería básica). En este sentido, el presente texto analiza el costo por concepto de mantenimiento y gestión de activos que incluyen costos inversionales (Capex) y operacionales (Opex), como la infraestructura, naves, bahías, talleres, almacenes, repuestos estratégicos, equipamiento y herramientas especiales, recursos humanos (mano de obra), capacitación, software de mantenimiento CMMS (Computerized Maintenance Management Software), etc.

Mar 1, 2015

By James L. Fenton

In its unending search for the raw materials that the affluent society of today requires the mining industry has found it necessary to go to great depths, in many cases, to produce these materials. Inherent with this problem is the insufficient technology relating to improving extreme environments that the mine personnel are exposed to. In this dissertation, the sources of heat flow into a mine along with the various effects that this heat has on the mine personnel are investigated. The object of dissertation is to compile all the available published information pertaining to these underground heat and their effects into one paper. This will provide the mining industry with an available easy-to-use to aid in the determination of mine ventilation requirements as the mines are in the phases of original planning or being extended to depth. Areas of significant, deficiencies it knowledge have been disclosed during this overall appraisal. Recommendations on important basic research needs are out lined for future consideration by Federal or industries sponsorship. This thesis should serve as a stimulus lo, future well-organized research efforts in the area of underground heat sources and their control.

Jan 1, 1973

By The Staff

THE object of the work was to increase the capacity of the plant and, if possible, to reduce costs of the actual unit grinding while doing so. The accompanying assays of an infra-sizer analysis of the cyanide tail (Table l) illustrate the problem in hand. The cyanide tail is a combination of two products, gangue and FeS2. The assay alters by virtue of a change in gold value due to grinding and the relative quantity of FeS2 in the sizes, which itself varies with the grind. The disposal tail is the residue after the cyanide tail is scavenged by flotation, most of the pyrite being removed for roasting. It presents a somewhat different problem, since grinding gangue is all gain, but -10 micron FeS2 does not float nearly as well as + 10 product. This results in compromise in the final size to be aimed at. Extra grinding has hardly any appreciable effect on the gold extraction from the FeS2. (See Milling Investigations Into the Ore as Occurring at the Lake Shore Mine; Trans. C.l.M.M., Vol. XXXIX, 1936).

Jan 1, 1940

Jan 1, 2002

By Richard F. Link, George S. Koch

Through the use of statistical methods, estimates of metal content and tonnage of an ore body made by using data from 18 diamond-drill holes are compared with actual values established with data from 1,829 drift samples. The reliability of the estimates made from the drill holes is assessed in several ways. The relationship of metal content (assay-width product) to grade is explained. It is concluded that useful estimates can be made from 18 drill holes provided that reasonable assumptions are made and certain risks accepted. The ore body investigated is the Don Tomas vein of the Frisco mine, San Francisco del Oro, Chihuahua, Mexico.

Jan 1, 1964

By Š. Šachlová, T. Lokajícek, M. Petružálek, T. Svitek, A. Štastná

During the past 20 years, alkali silicate reaction (ASR) as a cause of concrete deterioration has been studied by a wide range of experimental methods such as microstructural and macrostructural analysis, bulk chemical analysis, X-ray and neutron diffraction analysis, etc. All of these data are compared with expansion values of mortar bars (following ASTM standard C 1260). Recent studies indicate the useful application of non-destructive methods with the aim of better reflecting mechanical properties and the degree of deterioration of real concrete. Ultrasonic testing methods (including ultrasonic pulse velocity UPV) are widely used to determine material mechanical properties and the changes induced by a variety of mechanical or chemical processes. However, only a few laboratory studies of ASR focused on ultrasonic testing of mortar bars. Due to this fact, a heating chamber was designed and constructed to enable ultrasonic sounding of mortar bar specimens while stored in accelerating solution. Regular ultrasonic sounding of mortar bars reveals significant dependence of ultrasonic data such as longitudinal P-wave velocity, signal energy, signal amplitude and signal frequency on mortar bar storage time. Ultrasonic data were subjected to time domain as well as frequency domain analysis. Different storage conditions were used to determine the effect of ASR on ultrasonic parameters. Mortar bars, prepared in the same manner with one type of aggregate, were stored in cold or warm water or in an accelerating warm medium. Ultrasonic data accurately reflects the differences in hardening and deterioration of tested mortar bars due to different storage conditions. Ultrasonic results showed very good correlation with the results of ASTM standard expansion tests and much higher sensitivity to ASR-induced concrete deterioration. Expansion tests showed 1% measured length differences in comparison with up to 80% resolution of ultrasonic data. The ultrasonic testing proved to be a suitable laboratory method for investigating ASR-related processes and could lead to an improvement of standard testing procedures.

Jan 1, 2015

By V 9. 0 / 300 dpi

In the time period from the early 1980&apos;s to the present, longwall roof support technology has evolved tremendously. Chock supports and caliper shields were replaced by 2-leg or 4-leg lemniscate shields. The lemniscate linkage for which the support is named offers numerous advantages to the sup-port both as a fabricated structure and to its performance in the mining application. The hydraulic system, which is the dynamic element of the roof support, was essentially unchanged in early lemniscate shields with the exception of the complexity of additional hydraulic circuits to power a canopy tilt cylinder and canopy side-seals. The control of these fluid-powered functions was provided by direct manual control of valves energizing individual functions onboard the roof-support or the adjacent roof-support. This control valve-gear was comprised of multiple individual valves arranged in a "bank" or integrated into a single hydraulic distribution block with a single operating handle to select any independent function.

Jan 1, 1993

By G. A. Weisenfluh

The successful application of factors limiting the? availability of coal in eastern Kentucky depends on ac-curate assessment of the original resources. Examination of several previous coal-resource estimates for the region reveals significant differences among the outcomes. These differences relate to methods of analysis, biases in data and their utilization, and the problem of defining the lateral continuity of mineable beds. Improvements in the methods of estimating the original resources would greatly enhance the reliability of the results of the Coal Availability Program.

Jan 1, 1995

By L. Wilfley, G. A. Calboreanu

"Wear resistant 25% Cr hard cast iron is a heterogeneous material containing 1,600 HV hard chromium carbides embedded into martensitic matrix. It is the most used cast alloy in wear operations of mining industry, chemical industry, fracking, etc. During the last decade the hard iron manufacturers increased wear resistance in the following ways: • Reduce / eliminate harmful retained austenite and chromium + carbon depleted areas especially within eutectic carbide cells. In Max5A the improved 25% Cr alloy brittle carbide eutectic cells are removed which increases toughness. • Delay delamination between chromium carbides and matrix particularly during sliding abrasion wear. Delamination commences at the weakest chromium carbide – matrix contact lines exposing chromium carbide to localized bending stresses which gradually chip carbides away. Once the chromium carbide base is removed accelerated wear degradation occurs. • Evenly randomize and avoid discontinuities in the chromium carbide network. When chromium carbides are perpendicularly positioned to the wear surface wear rate is minimized. On the contrary the highest wear rate takes place when 3D oriented chromium carbides are parallel with the wear surface. In this case chromium carbides cover top network discontinuities being just matrix supported which leads to rapid carbide cracking. The new hard iron discussed in this paper fulfils and exceeds the above requirements increasing the casting service life around 250% in various wear operations. Physical and mechanical properties of Max5A are compared with well manufactured Industry Standard 25% Cr hard iron. The paper presents practical accomplishments obtained in the USA, South America and India. INTRODUCTION The chemical composition of Max5A and Industry Standard 25% Cr are identical like specified by ASTM A532 Class III Type A requesting C = 2.0-3.3% and Cr = 23.0-30.0%. Manganese, silicon, nickel, molybdenum and copper contents are limited by maximum accepted quantities.[1] According to published data the eutectic chromium carbides chemical composition of 25% Cr hard iron is Cr = 54% and C = 8% which indicates strong depletion of chromium and carbon along chromium carbide - matrix interfaces. [2] The optimized Max5A microstructure has minimized retained austenite, is devoid of harmful carbide eutectic cells and has the most advantageous chromium carbide and secondary chromium carbide morphology. This favorable microstructure increases wear resistance, mechanical properties and corrosion resistance. The paper compares the Max5A microscopic features and mechanical – physical properties with similar properties of high quality Industry Standard 25% Cr."

Jan 1, 2017