Search Documents

By Greg Colzani, Emily Thompson

The 3RPORT Project, includes a 5-mile tunnel excavated by a 19-foot diameter slurry Tunnel Boring Machine below the city of Fort Wayne, IN. The Geotechnical Baseline Report (GBR) indicated vuggy to massive argillaceous dolomite within the tunnel alignment. During excavation of the first reach, the TBM encountered zones of cohesive clay and sandstone presented in full face and mixed face conditions. The occurrence of Sandstone was not a “Baselined Condition” described in the GBR for this reach of the alignment. This paper will discuss the methodology to investigate, mitigate and evaluate the DSC impacts on TBM performance.

Dec 1, 2022

By Thomas Schwind, Elmar Feigl, Gerald Skalla, Angelos Gakis

Cedarvale station was constructed as part of the Eglinton Crosstown Light Rail Line, under the operational Yonge-University Line Subway box of Toronto Transit Commission (TTC). The station was constructed as an open-cut, which necessitated the underpinning of the existing TTC box to minimize the impact on the Subway and allow its unhindered operation. Six mined galleries, 4 m wide by 2.75 m high, were excavated sequentially (SEM) immediately under the existing box, to provide the required space for the installation of the main underpinning beams. This novel solution was executed successfully providing quick access for the main excavation works to commence.

Dec 1, 2022

By Joseph Jensen

MANY fields have been zoned by nature with shales and intermediate waters between oil zones. Limitations thus imposed have been the basis on which the field was developed. In contrast thereto, in the Ventura Avenue Field, nature proved more generous. Always expecting to find such similar limitations, operators drilled deeper and deeper into the oil zone without finding any distinctive shale bodies other that the Gosnell shale and only one intermediate water, which became the point below which the final water shut-off of each well was made. Thus, on top of the structure, about 3300 ft. of oil-bearing zone has been penetrated below this intermediate w9ter-a distance of 4000 ft. below the Gosnell shale. At first it seemed that the greater the penetration in the zone, the better the well. The error of this assumption became evident

Jan 1, 1930

By Don Masson

MUCH has been written and many prophecies made on the subject of plastics as a replacement for metal, and the extent to which these materials will compete with each other for peace- time markets. (Metal is used in a broad sense to include all types.) But although certain synthetic resin materials have made considerable headway in war production, this change to plastics can hardly be regarded as a serious threat to the mining and metallurgical industries. Even today, the total yearly tonnage of plastic materials is approximately only 1 per cent of that of steel, and only a small fraction of this might be considered as actually replacing steel. However, these figures must not be taken as indicating that the importance of plastics in fields hitherto considered exclusively the territory of metals is negligible-far from it. Considering the comparatively minute tonnage of plastics now being produced in comparison to the output of metals, the number of applications where plastics have augmented or aided the sale of metals is considerable.

Jan 1, 1944

By J. L. Mehaffey

A variety of chemicals offered by Armak were evaluated as dewatering aids for aqueous slurries of silica sand, sparsand and feldspar; an established commercial dewatering aid was used as a control. A number of Armak's potential dewatering aids yielded lower moisture retention values than did the commercial product on all of the mineral samples. In addition to the chemical dewatering evaluations, some of the mechanisms involved in the removal of water from these mineral samples were examined.

Jan 1, 1983

By VÍCTOR VÁZQUEZ-VÁZQUEZ, GUILLERMO TIBURCIO-MUNIVE, María M. Salazar-Campoy, JESÚS L. VALENZUELA-GARCÍA, OFELIA HERNÁNDEZ-NEGRETE

The present study examined a process for precious metal recovery (silver and gold) from difficult minerals which exhibit refractory characteristics to cyanidation and ammonium thiosulfate leaching (low extraction and high consumption of leaching agent). It is well known that mangano-argentiferous minerals are mainly composed of manganese, silver, gold, and iron. In this research, a mineral sample from Monte del Favor mine, located in Hostotipaquillo, Jalisco, Mexico, was physically and chemically characterized by X-ray powder diffraction (XRPD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), fire assay, and atomic absorption spectroscopy (AAS). Two-stage leaching was carried out: first to eliminate manganese from the sample using sodium sulfite (Na2SO3) as a reductive reagent and sulfuric acid (H2SO4) and a second stage to dissolve silver and gold with sodium hypochlorite (NaClO) and hydrochloric acid (HCl); the results show extraction around 96% for Mn and 98.73% and 83%of Ag and Au, respectively. The usefulness of high acidity and Na2SO3 to obtain good results in Mn and Ag leaching is discussed along with the roles that HCl and NaClO play in the dissolution of Ag and Au values.

Apr 15, 2020

By Fernando de Oliveira Boechat

As maiores pressões e temperaturas atualmente empregadas a fim de aumentar a produtividade de fornos de DRI têm resultado em um subproduto indesejado: o aumento da geração de clusters. Estes clusters prejudicam o fluxo da carga e a permeabilidade do leito. A fim de limitar o tamanho destes aglomerados o forno MIDREX dispõe de três conjuntos de quebradores localizados em diferentes posições do forno após a redução da carga. A interação entre clusters e esses quebradores, entretanto, pode também prejudicar o fluxo da carga e aumentar a geração de finos. O trabalho utilizou o método dos elementos discretos (DEM) para avaliar as energias e forças resultantes da interação entre os clusters formados e os quebradores. A descrição dos clusters foi realizada usando o bonded-particle model, disponível no EDEM. Simulações mostraram que a presença de clusters altera as forças e velocidades no entorno dos quebradores que tenderiam a aumentar a geração de finos no reator.

Aug 16, 2017

By I. Ince, S. Kahraman, M. Rostami, B. Dibavar

The density, porosity, and strength of rocks are fundamental in the design of geo-engineering projects. Determining these properties requires the preparation of smooth core samples, which is usually impossible for soft rocks. Besides, only fragmented samples may be available in some projects. A method for predicting rock properties from rock particles such as drilling debris would therefore be useful. This study was undertaken to develop prediction equations for compressive strength (UCS), tensile strength (BTS), density, and porosity values from the crushability index (CI) obtained from rock fragments. The results showed that UCS, BTS, density, and porosity were strongly correlated with the CI. The physical characteristics and strength of rocks may be predicted with the help of the derived equations. The CI test is a valuable tool for estimating rock properties in drilling projects and in situations where core specimens are not available.

Mar 14, 2024

By A. Ribeiro

The effective utilization of resources and process optimization play a crucial role in the sustaining and growth of overall businesses. This principle holds true in the mining sector, where particular attention is required during the comminution steps. This necessity arises from the fact that mining operations often consume substantial amounts of energy in mineral processing. Therefore, it becomes imperative to thoroughly study the integration of comminution steps. In many instances, an approach to be studied is the operation commencing with the drill and blast phase and culminating in the grinding product process. Nevertheless, establishing an optimal integration between drill and blast operations and the grinding phase is a complex undertaking due to the direct influence of rock characteristics on this process. And in many cases, the complexity and variability of such physical characteristics makes mining operations to ignore such influence. Consequently, Enaex Mining Technical Solutions (EMTS), in collaboration with Lundin Mining's Chapada Mine engineering team, and with the assistance of Hatch Consulting and Technology, has undertaken a comprehensive study aimed at enhancing mill throughput at the Chapada operation. The basis of this study lies in characterizing the rock masses present in the Chapada Mine to gain a deep understanding of the material that needs to be comminuted. Subsequently, the mineral processing team determined the most suitable size distribution for the Run-of-Mine (ROM) material. With this information, the drilling and blasting team built a site-specific blast fragmentation model, able to simulate various blast design scenarios. This approach enabled to optimize the utilization of available drilling and blasting resources while striving to achieve the optimum ROM characteristics. Since 2021, the Mine to Mill methodology has been progressively implemented at the Chapada Mine. As a result, the blasting engineering team now utilizes the blast plans generated by the fragmentation model simulations as a foundation for designing blast plans that align with the operational and financial capacities of the mine. Overall, it was predicted that this implementation could lead to an average increase in mill throughput of 13-22 % depending on blend feed, once all recommendations are implemented. Even with partial implementation, plant results demonstrate a 5 % increase compared to the period before the Mineto-Mill project, without any coarsening of the associated grinding product size.

Jan 1, 2024

By Marcelo Cervantes Del Rio Baptista

Nos últimos anos a indústria siderúrgica no Brasil vem sofrendo um processo lento e cruel de encolhimento de sua participação no PIB, em decorrência de diversos fatores políticos e econômicos. Apesar do grande esforço por parte das empresas, a capacidade de produção de aço pouco cresceu neste período, permitindo que as despesas cresçam mais rápido do que as receitas. Esses fatores têm mostrado aos profissionais do setor que a mudança do cenário só ocorrerá ao se produzir com o máximo de eficiência. O objetivo deste trabalho é demonstrar que a lubrificação tem grande participação no aumento da produtividade e redução de custos da manutenção. Em suma, será apresentado um estudo sobre como a lubrificação correta influencia no aumento da produtividade das siderúrgicas. Com base nos resultados dos testes realizados em duas grandes empresas do setor, este trabalho demonstra o aumento significativo de performance no Mandril da bobinadeira e mancais dos convertedores, após estudo detalhado da lubrificação.

Aug 17, 2017

By Wilson Quispe, Luis Silva, Rubén Alvarado

El presente trabajo nos permitirá compartir los desafíos que en el pasado reciente se enfrentaron, cuando se pusieron en marcha las primeras operaciones de gran minería que contemplaban los molinos SAG el cual fue resuelto acudiendo a empresas extranjeras para poder cubrir la necesidad de realizar el cambio de los revestimientos. Esto porque los molinos SAG eran nuevos en el país y las empresas prestadoras de servicios mineros carecían de experiencia para poder ejecutarlo.

Sep 29, 2023

By C. Snyman, M. Le Roux, Q. P. Campbell, S. Engelbrecht

Due to the ultrafine particle size required for effective processing of chromite ores, dewatering of the concentrates presents a challenge. It is not uncommon for the ore to have elevated moisture contents even after dewatering, which must be reduced to required levels of between 8% and 10% by mass for further processing. Contact sorption drying has shown promise in test work on fine coal. This method was used to study the dewatering of chromite on a laboratory scale using 3 mm spherical activated alumina ceramic beads as a sorbent. Three different sorbent-to-chromite mass ratios, namely 0.5:1, 1:1, and 2:1, were tested with different process conditions, including dewatering in a stationary and a rotatingl bed. The experimental work showed that it was possible to achieve the target moistures in less than 10 minutes, irrespective of the sorbent-to-chromite ratio used. Ratios of 1:1 or higher, however, proved to be the best. The sorbent reusability at mass ratios of 1:1 and 2:1 were therefore tested. With a 1:1 mass ratio, the sorbents could be reused for three cycles, while with 2:1 ratio, the number of cycles increased to six. The sorbent-to-chromite mass ratio used had a significant influence on the required contact time and the reusability of the sorbents.

Oct 3, 2023

By Matheus Sampaio Modesto de Paula

O presente trabalho mostra o desenvolvimento de um produto, até então não comercializado pela CSN/PR, criado para o aproveitamento da capacidade ociosa de seu laminador reversível a frio. Historicamente, a produção do laminador era direcionada exclusivamente para o abastecimento de uma linha de galvanização contínua, mas trabalhos bem sucedidos para o aumento da produtividade do laminador resultaram em capacidade excedente do equipamento. Diante desse cenário, a comercialização de bobinas Full Hard se tornou uma opção viável para a abertura de mercado e aumento de competitividade, frente a atual pressão imposta por produtos importados. Visitas aos potenciais clientes foram necessárias para o levantamento das características importantes a seus processos produtivos e adequação dos parâmetros utilizados no laminador reversível. Atualmente o produto está homologado e sendo fornecido a clientes externos, e espera-se o aumento da carteira, dependendo apenas da evolução do mercado.

Jul 30, 2018

By Bo Liang, Hongmin Zhu, Kai Huang, Shafiq Alam

A new approach of recovering platinum and palladium from electronic wastes by hydrochloric acid leaching followed by selective adsorption on low-cost and environmentally benign biomass sorbent prepared from easily available agriculture waste is suggested. The obtained adsorbents were prepared by a combination of chemical modification and hydrothermal carbonization process with (NH4)2C2O4. It was found that the maximum adsorption capacity of hydrothermal carbonized garlic peel for Pt( ) and Pd( ) was 1.64 and 0.42 mol/kg respectively. The Langmuir adsorption isotherm was applied to describe the adsorption process. Kinetics of the Pt( ) and Pd( ) ions adsorption was found to follow pseudo-second-order rate equation. The adsorbents were examined by scanning electron microscope (SEM), and Fourier transform infrared spectroscopy (FT-IR). Based on the characterization results, a possible mechanism of Pt( ) and Pd( ) ions adsorption with the hydrothermal carbonized garlic peel was proposed. This study provides a promising adsorbent with efficient adsorption property for platinum and palladium recovery from the leach solution of electronic wastes.

Jan 1, 2016

By M. Wenzel, Dang Thanh Tung, Nguyen Anh Duc, Nguyen Huu Luong, Dang Van Sy, N. Kelly, K. Gloe, K. Kretschmer, Phuc Nguyen Le, K. Schnaars, S. Robles M, L. Götzke, J. J. Weigand

The recovery of rare earth metals from secondary sources has attracted much attention due to their ever expanding demand in the high-tech industry. The studies reported here focus on the hydrometallurgical recovery of lanthanum and cerium from spent fluid catalytic cracking (FCC) catalysts in a two-step process: leaching with nitric acid and solvent extraction by tri-n-butyl phosphate (TBP) and di(2-ethylhexyl)phosphoric acid (D2EHPA). The experiments show a high dissolution yield of about 93% lanthanum and 42% cerium in a single leaching step with 2 M (126 g/L) HNO3 at 80 °C; only 11% aluminum has been dissolved simultaneously. In the subsequent solvent extraction step the best results for this leach liquor could be achieved using a 1:1 mixture of 25% (v/v) TBP (0.92 M) and 25% (v/v) D2EHPA (0.76 M) in n-decane without the need for any pH adjustment. In that case La(III) and Ce(III) can be extracted with 60% and 74% yield respectively in one stage from the majority of accompanying matrix elements. In particular no extraction of Al(III) could be observed under these conditions.

Jan 1, 2016

By M. Getz, G. Asbjörnsson, M. Evertsson, E. Clausen

The mining and minerals processing industry is gradually being digitalised to improve efficiency and reduce waste. One aspect of this transition is to ensure that relevant process-data in sufficient quality and quantity is given to the operator in the right format and at the right time to improve decision-making. Augmented reality (AR) can serve as a potential ICT-based support tool for human operators to achieve this goal. With AR, virtual information is combined with the real world in real-time. Therefore, AR technology has the potential to fulfil the need for improved data visualisation in Industry 4.0. This article is the result of a collaborative effort of Chalmers University of Technology and RWTH Aachen University to identify selected state-of-the-art applications of AR that are currently being applied in the mining and minerals industry or selected related industries. This paper aims to show opportunities for the application of AR in the mining and mineral processing industry with selected conceptual applications. This paper concludes with several requirements identified as necessary to implement the conceptual applications of AR in the mining and minerals industry. Keywords: Augmented reality, mining, mineral processing

Jan 1, 2020

By Mateus Sotelo Menezes

A família de aços avançados de alta resistência – AHSS contempla uma variedade de materiais que são utilizados principalmente na indústria automotiva. Os aços bifásicos incluem-se nesta classe e são assim denominados devido a sua microestrutura composta por ferrita e martensita. Apresentam alta resistência mecânica associada à ductilidade, o que permite a aplicação de grandes esforços em pequenas áreas sem que ocorra fratura. Este trabalho visa verificar, através de caracterização metalográfica, ensaios de tração e anisotropia, as propriedades mecânicas do aço DP600 para trabalho a frio. A curva tensão-deformação de engenharia para este aço foi estabelecida através de ensaios de tração até a ruptura do corpo de prova. Foram obtidos valores médios de 330 MPa para o limite de escoamento, 589 MPa para o limite de resistência à tração e 20% de alongamento. Os índices de anisotropia também foram verificados através de ensaios de tração. Estes resultados foram comparados com valores encontrados na literatura. De um modo geral, as chapas ensaiadas resultaram em uma diferença de valores de aproximadamente 10%, possibilitando sua utilização a frio.

Aug 16, 2017

By Alessandra Savazzini dos Reis

A crescente preocupação em relação às áreas de proteção ambiental e ao alto consumo de argila, matéria-prima da cerâmica vermelha, ocasiona a indisponibilização progressiva de reservas de argilas no Brasil. Com isso, vê-se a necessidade de incorporar resíduos na massa argilosa para confecção de produtos de cerâmica vermelha. A indústria de cerâmica vermelha brasileira consome cerca de 10 milhões de toneladas de argila ao mês para produção de telhas e blocos. Na própria olaria são gerados resíduos, tal como, o resíduo de massa cerâmica crua originado na etapa de conformação das peças. Este trabalho visa incorporar o resíduo de massa cerâmica crua na massa argilosa usada em cerâmica vermelha. O resíduo foi caracterizado por meio de ensaios de FRX, DRX, limites de Atterberg e distribuição de tamanho de partículas. Corpos de prova feitos com massa argilosa e resíduo em teores variando de 10% a 90% (massa) foram conformados, secos à 110ºC, queimados à 900ºC em forno industrial e submetidos a ensaios de absorção de água, porosidade aparente, massa específica aparente e resistência à compressão. Os resultados evidenciaram que as propriedades cerâmicas avaliadas nos corpos de prova da massa argilosa incorporada com o resíduo atendem aos valores das argilas-padrão brasileiras para cerâmica vermelha.

Aug 17, 2017

By Sandra Lúcia de Moraes

Vários trabalhos voltados a resolução dos problemas da utilização de bentonita no processo de aglomeração de minério de ferro referem-se ao emprego de aglomerantes orgânicos, sendo que os dois tipos principais são os à base de celulose e de poliacrilamidas. Este trabalho teve como objetivo um melhor entendimento da ação de um aglomerante à base de carboximetilcelulose no ganho de resistência mecânica da pelota. Foi avaliada a interação entre a superfície mineral de dois concentrados tipo pellet feed brasileiros e os componentes presentes no aglomerante Peridur de uso comercial. O método proposto e desenvolvido no presente trabalho permitiu comprovar que um mesmo aglomerante atua de maneira diferenciada dependendo do tipo de minério de ferro empregado. Isto reforça a importância do entendimento de como cada produto, utilizado como aglomerante no processo de pelotização, age nos constituintes do minério de ferro para promover o incremento necessário de resistência mecânica das pelotas.

Aug 16, 2017

By Alexandre Rodizio Bento

A competitividade do setor automotivo exige maior agilidade na gestão de ferramentas de usinagem. Para atender esta necessidade flexibilizar e automatizar o processo de gestão de armazenagem é fator primordial. As ferramentas de usinagem muitas vezes têm custo elevado e a necessidade de controle constante é imprescindível no setor automotivo. A padronização de armazenagem aliada a um equipamento específico para controlar ferramentas surge como uma opção. Pois, a troca de produtos deve ser ágil durante a fabricação para evitar perdas e máquinas ociosas no chão de fábrica. Assim, suprir esta necessidade com velocidade é essencial e de suma importância para a integração entre os departamentos de produção e logística. Neste cenário, a tecnologia de armazenagem permite agilizar e flexibilizar a gestão de ferramentas de usinagem, além de possibilitar ganhos de produção. Neste trabalho, apresenta-se a substituição do processo manual de armazenagem de ferramentas de usinagem baseado em caixas e prateleiras, por um sistema com tecnologia de armazenagem vertical. Esta substituição permite automatizar o controle de ferramentas, reduzir o custo de estoque e flexibilizar a troca de produtos na produção. Os resultados deste processo permitem garantir a melhor gestão das ferramentas de usinagem, evitar paradas nas linhas, reduzir custos operacionais e manter estoques em perfeito equilíbrio, entre o aumento de produtividade e a redução de custos.

Aug 8, 2018