Search Documents

By T. E. Swigart

In connection with experimental work by the Bureau of Mines to determine effects of back pressure . on oil wells * , data were compiled on the engineering conditions in the oil field selected , in order to afford a more complete understanding of the wells tested , and to illustrate the extent to which underground conditions should be studied when making oil -field experiments of this nature . This report , containing the data mentioned, may be of interest to the oil industry , as it describes briefly the methods of operation employed in developing and exploiting shallow well territory .

Feb 1, 1923

By Robert C. Simpson, Ghada S. Ellithy

"There are several methods for estimating the axial capacity of drilled shafts installed in coarse-grained soils. Most methods estimate the ultimate capacity for side friction and tip resistance. Design capacity is then calculated by applying a resistance factor to the ultimate capacity. In reality, however, ultimate resistance may not be mobilized except after a significant displacement that is not structurally tolerated in either compression or tension modes.A full- scale load test is the best way to obtain the load settlement curve for a drilled shaft, especially in soil formations where accurate estimation of soil frictional properties from a field investigation may be difficult. This paper presents the results of a static, axial, compressive bi-directional load test, using the Osterberg method (O-cell test). The test was designed so that the shaft above the O-cell would move up and the shaft below it would move down when loaded. At the start of the test the concrete around the O-cell is fractured generally on a plane near the bottom of the cell.The test was designed to validate the design capacity of drilled shafts embedded into the Vashon recessional outwash (Qvro), which is a glacially derived sediment consisting of thick deposits of cobbly sand and gravel relatively free of silt and clay found in the Seattle, WA area. The test shaft consisted of a 2.5- feet (0.75 m) diameter drilled shaft. The test shaft was installed to a depth of about 47 feet (14.3 m) into this formation. A maximum load of 437 kips (1.95 MN) was applied during the test, in each direction. The maximum load was attained at upward and downward displacements of less than 0.1 inch (2.5 mm), respectively.Although the load test did not yield ultimate values, the results are compared to the design assumptions using methods adopted in the FHWA and AASHTO guidelines, which verified the adequacy of the design assumptions. We conclude that more emphasis is needed in the prediction of the service loads and corresponding mobilized displacement that may lead to a more cost effective design. It is also clear that more testing to higher loads could lead to more efficient designs on specific projects and generally as data is added to the local knowledge base."

Jan 1, 2015

By Amanda R. Parry, Chris R. Pray

Predicting and modeling the soil structure interaction of laterally loaded piles with significant unbraced lengths is one of the challenges faced in designing many waterfront structures. Designers often rely on pile specific design software to calculate forces in an embedded pile and then couple that with either a structural design software to capture the behavior of the rest of the structure or use potentially overly conservative assumptions to omit modelling the piles entirely. Given that some projects have hundreds of piles coupled with hundreds of loading conditions, the shuttling of results from the structural analysis software into the pile analysis software can become cumbersome, difficult to track and manage, and prone to user input errors. An alternative approach recently used on two large marine infrastructure projects consisted of calibrating a structural analysis software to replicate the resultant outputs from a software developed specifically for pile analysis. This calibration was done using thoughtfully placed springs along a pile modeled in the structural analysis software to replicate the soil-structure interaction of the piles. The focus of this paper will be on the methodology used to calibrate the two software programs and an evaluation of the results which showed close agreement. Based on the two case studies, calibrating a generic finite element analysis software via this method should be considered as a reasonable and time saving design approach for pile-supported structures.

Sep 8, 2021

By A. Angelov, U. Peukerd, S. Gaydardzhieve, A. Stefanov, K. Grossman, V. Stoilov

Flotation concentrate originating from the Asarel-Medet porphyry copper mining and processing complex in Bulgaria has been subjected to regrinding using a Ro-Star mill; the effects of which on the downstream metallurgical behaviour are discussed. Particularly the effect on the liberation degree was studied through an optical microscopy and MLA-SEM automated mineralogy. On the other hand, copper selective flotation of the reground bulk concentrate was realised to evaluate the anticipated metallurgical improvement. Process parameters such as involvement of prior hydrocycloning and variation of collector dosage have been evaluated. Within a two-minute residence time inside the Ro-Star mill, an improved liberation degree of the copper bearing minerals has been observed. As a consequence, enhanced copper recovery and selectivity against pyrite was noted. It has been found that in order to guarantee efficient flotation of the resulting ultrafine particles, a modified flotation regime (i.e. changing collector suite and dosages) should be followed. Keywords: RoStar Mill, liberation, flotation recovery, ultrafine particles

Jan 1, 2020

By B. T. McKenna, H. Nirschl, P. Morsch, B. Fränkle

Generally, filter media used in filter presses have a limited operational life. Besides mechanical damage, there is a growing deposition of fine particles with increasing filtration cycles, the so-called blinding, inside the filter cloth. The resulting decreasing pore diameters not only affect the efficiency of the filtration process itself by increasing the filter medium resistance, but also make it more difficult to regenerate the filter press between the individual cycles, e.g. leading to an insufficient cake discharge. Since tailings filtration requires handling of large process flows containing a significant fraction of particles in the lower micrometer range, an investigation into media rejuvenation is of interest. Keywords: Tailings filtration, filter fabric resistance, filter media regeneration, filter cleaning, intraweave contamination

Jan 1, 2020

By T. Song, X. Wang, X. O. Xia, X. J. Luo, B. Chen

Interparticle breakage is the main crushing mode of an inertia cone crusher according to its working principle and feeding condition. In this paper the breakage behaviour of an inertia cone crusher is investigated, based on energy controlled compression combined with the vibration theory, rather than geometry controlled compression (form conditioned) which plays a major role in conventional eccentric cone crushers. The effect of feeding and operating conditions on breakage behaviour was described quantitatively from the perspective of energy consumption and product size distribution. The influence of feeding conditions, discharge size settings and vibration exciter speeds on the crushing process and product quality has been studied according to the results of laboratory crushing experiments. The results of the experiments show that the particle size of broken products becomes finer with the decrease of a discharge gap within the gap range selected by the experiment. The product size increases significantly when the gap approaches the upper limit of 6 mm. The variation of eccentric speed has a more prominent effect on reducing the product size compared with the change of discharge gap. The change in product size is not apparent when the eccentric speed rises to a certain level. The throughput of an inertia cone crusher is sensitive to the change of discharge gap, which increases linearly with the discharge gap and decreases with the eccentric speed. The change of feeding conditions has little influence on the crusher throughput. Keywords: Inertia cone crusher, interparticle breakage, energy consumption, product size distribution

Jan 1, 2020

By L. Morgan, M. Le Roux, Q. P. Campbell

Dry coal processing is becoming increasingly favoured as a fine coal beneficiation technique. The decline in suitable good-quality coal, as well as the ongoing decrease in usable process water, makes dry beneficiation of the fine coal fraction even more crucial. Dry fine coal beneficiation is a relatively young process with most of the methods still in the developmental phase. Additionally, many of the dry processing options available are better suited for coarser (+6 mm) and easy-to-beneficiate coal. Air winnowing for fine particles has been established in both agricultural and pharmaceutical industries, which indicates that the method can be used to separate smaller particles on a density basis and therefore, may prove effective in the coal industry as well. A proof of concept study was conducted using both computer-based simulations (which do not form part of this paper) and physical experiments. The initial winnowing unit consisted of a closed box with a horizontal air stream flowing through the top section. Coal particles were injected into the air stream and displaced horizontally across a distance (x), depending on the particle size and density, thus actuating a separation based on these two parameters. For this study particle sizes of 6, 4 and 2 mm were used all with a density ranging from 1200 kg·m-3 to 2000 kg·m-3. The simulation in Star CCM+ confirmed the findings of the mathematic behavioural model and provided a virtual representation of the separation using streamlines and particle tracks. The coal tests prove that size separation can be achieved at an airflow velocity of 21 m·s-1 and the density cut-point can also be predicted by using the prediction matrices constructed as part of this study. The results show efficiency values (EPM) of 0.11 and 0.09 at density cut-points of 1400 kg·m-3 and 1500 kg·m-3 respectively. The data obtained from the study indicates that air winnowing can be used to separate fine coal particles based on both size and density. However, in order to achieve an efficient density separation, a narrow size range is required. With some improvements to the model, simulation, method and design, the separation efficiency can also be improved. The next phase of testing will include the upscaling of the process to a demonstration plant, optimising the separation unit and testing the method on different qualities of coal. Keywords: Dry processing, fine coal, winnowing, simulation, tracers, demonstration plant

Jan 1, 2020

By L. E. Salinas-Farran, S. J. Neethling

Key variables in heap leaching include permeability, mechanical stability and mass transport. All of these properties can be manipulated by agglomerating and curing the ore before stacking it into heaps. The chemical and structural evolution of the agglomerates during curing is key to improving agglomerate properties and, ultimately, heap performance. It is possible to image the internal structure of agglomerates using SEM/EDX (e.g. QEMSCAN or MLA), although these methods are destructive and do not represent the 3D structure of the agglomerates. A non-destructive alternative is to image the agglomerates using X-ray Microtomography (XMT). Not only does this provide 3D information, it also allows the same samples to be repeatedly scanned, allowing the time evolution of the agglomerate structure and chemical composition to be tracked. In this paper we compared the behaviour of ores agglomerated using a combination of sulphuric acid and ferric sulphate with ones in which chloride ions are added to the recipe, since chloride leaching is gaining in popularity as a chemical alternative to bioleaching for sulphide ores. We tracked the curing process beyond the typical time scales to see the impact that this has on both the agglomerate structure and the subsequent leaching behaviour. Keywords: Heap leaching, curing extent impact, leaching kinetics, ferric-chloride leaching

Jan 1, 2020

By S. C. Maji, U. S. Chattopadyay, S. Chaudhuri, T. Gouri Charan

India is devoid of coking coal resources, which is a vital raw material for coke making. As a result it has to import about 80% coking coal for steel making. Indian National Steel Policy, 2017 has envisaged crude steel production around 300 million tonnes Mt) by the year 2030-31 and forecasts coking coal demand of 161 Mtpa (million tonnes per annum). One way of improving the indigenous resources is to study the performance of existing washeries and to improve the clean coal recovery by adopting suitable technology. A study was carried out, mainly to focus on the fine coal circuit of an existing coking coal washery, to generate the desired quality of clean coal. The operating coking coal washery being studied is presently feeding coal from nine different sources with varying feed ash contents. The coal fines varied in ash content ranging from 19.5% - 43.6%. For treating the coal fines, the washery has operated a spiral for the past few years. Performance studies were carried out, and it was found that the spiral is not efficient in recovering the cleans. Detailed investigations were carried out on the coal fines using flotation techniques, and it was found that to achieve a low ash clean coal, the froth flotation is a much better beneficiation option than a spiral, The studies showed that the recovery of clean coal through a spiral is 67.7% at ash content of 27.0%, while flotation tests showed a recovery of 68.1% at 16.5% ash content. Keywords: Coking coal washery, near gravity material, spiral washer, froth flotation

Jan 1, 2020

By V. C. Koppe, J. F. C. L. Costa, D. M. Marques, A. Amaral

Errors associated with estimating the grade of an attribute of interest in a deposit can compromise planning, sequencing, and mineral beneficiation decisions. Several factors are associated with estimation errors. Among them, we can highlight the factors associated with sample spacing, the size of production volumes, and the variability of the attribute considered in the estimation. The access to estimation error can be obtained by some geostatistical methods, for example, by stochastic simulation. However, this is a process that in some situations is computer intensive and takes time. Previous works have proposed a simplified method to access the Maximum Estimation Error (MEE) associated with different types of grade variables, depending on the sample spacing, at small production volumes and considering specific coefficients of variation ranges. This paper presents an approach to assess the MEE associated with long-term volumes. Considering the methodology proposed, it is possible to approximate if a specific drilling pattern used in a deposit provides an acceptable pre-determined estimation error for Resource Classification. Results and considerations on the impact of the geometry of larger production volumes on the MEE calculation are also presented.

Jun 25, 2023

By W. Guiye, L. Chongjun, L. Huinan, Z. Yangge, H. Long

The current application of copper-molybdenum (Cu-Mo) separation inhibitors is often associated with large dosage, high toxicity, environmental pollution problems. In order to solve these problems, a light sensitive Cu-Mo separation inhibitor LS（light sensitive inhibitor，abbreviated to LS） was developed. In this paper, inhibitory performance, photodegradation rule, and acting mechanism of LS were studied. The subsequent test results showed that, compared with traditional inhibitors, LS has shown comparative advantages, with lower dosage and good inhibiting effect. A series of flotation tests with LS as inhibitor were conducted on a Cu-Mo concentrate. A locked-cycle test showed that a molybdenum concentrate containing Mo 49.88% and Cu 0.6%, with 93.23% molybdenum recovery and a copper concentrate containing Cu 29.92%, with 99.99% copper recovery can be obtained. The photodegradation performance of the reagent was investigated under 365 nm, 254 nm and sunlight irradiation. The degradation of the reagents could be completely achieved by irradiation of three wavelengths of light. However, with the different wavelength of irradiation light, the degradation rate is different, the time required to reach 50% degradation rate being 3 h (254nm), 4 h (solar light) and 6 h (365nm) respectively. The inhibition mechanism on chalcopyrite was studied. FTIR study showed that LS could be adsorbed on the surface of chalcopyrite by chemical adsorption, which could enhance the hydrophilicity of chalcopyrite. Ultraviolet adsorption tests indicated that the adsorption capacity of LS on chalcopyrite surface was greatly affected by pulp pH value, and the proper pH value was 5-9. Keywords: Copper-molybdenum separation, Inhibitor, Light-sensitive, Photodegradation, Mechanism.

Jan 1, 2020

By L. Gutierrez, R. Yepsena

Enargite in porphyry copper deposits is an important mineral as it displays good floatability under the presence of the collectors usually used in the flotation of copper sulfides. As a result, copper concentrates grades are reduced. As scarcity of water resources is a problem relevant to Chilean mining, the use of seawater is a feasible solution. The behaviour of copper sulfides and molybdenite in the process of flotation in seawater was previously studied but not for enargite. The objective of this research is to study the behaviour of the enargite in different conditions of electrochemical potential during the process of flotation using seawater. The study was carried through micro-flotation tests using pure samples of enargite, at Eh values ranging from -300 to 500 mV(SHE), both in seawater and aqueous solutions containing calcium and magnesium. The results show that at pH 10.5 in seawater, the enargite and chalcopyrite recoveries are reduced throughout the whole range of Eh studied. At pH 9 in seawater, enargite and chalcopyrite are depressed under reducing and slightly oxidising conditions. The recovery of both minerals drastically decreases at Eh values lower than -100 mV and greater than 400 mV. The behaviour of enargite in seawater flotation differs from that observed in conventional water, since in the latter case the recovery of enargite decreases at higher potentials close to 500 mV. Keywords: Enargite, flotation, seawater, redox potential

Jan 1, 2020

By W. Soetaert, P. Dhar, H. R. Kota, M. Thornhill, S. Roelants, I. V. Chernyshova

Yeast-derived bola-amphiphiles have attracted considerable attention for their applications in various industrial sectors in recent years. However, only a few studies on this class of surfactant were reported to be relevant to mineral processing applications. In this paper, one of the novel surfactants, acidic glucolipid obtained from Candida bombicola sophorolipids and modified by using Penicillium decumbens naringinase substrate has been evaluated for its interaction with chalcocite and calcite minerals because of a new Cu-ore Nussir deposit in Norway containing calcite impurity. The interaction of glucolipid biosurfactant with copper sulphide and carbonate minerals was investigated with zeta potential, adsorption and FTIR studies, and also by Hallimond tube and bench scale flotation tests using pure minerals and Nussir copper ore, respectively. The results illustrate collector adsorption and flotation of copper sulfides at neutral pH. The bench-scale flotation results demonstrate that copper sulphides can be selectively floated from carbonate and silicate gangue minerals. This study underlines the glycolipid’s high potential for its use as collector for flotation of valuable copper sulphide minerals. Keywords: Flotation, biosurfactants, adsorption

Jan 1, 2020

By Yaxiong Wang, Yong Li, Yuedong Wu, Haigang Dong, Jiachun Zhao

A roasting-leaching process has been developed for concentrating platinum group metals (PGM) from a PGM-containing ferroalloy. The optimized roasting conditions used a NaOH-to-ferroalloy mass ratio of 1.2 at 600 °C for 2 h. The roasted product mainly comprised Na4SiO4, NaFeO2 and Fe2O3. The iron oxide and sodium silicate associated with the roasted product were leached in water and dilute sulfuric acid solution, while the PGM was concentrated in the acid-leached residue. A PGM concentration of 23.4% was obtained with assaying, and the concentration factor of PGM from the ferroalloy to PGM concentration was greater than 9.

Jun 14, 2021

By Cloutier JY, Quinn P, LeClerc A, Dube G, Agar GE

Gold dissolution by cyanide requires the presence of oxygen which is usually supplied by sparging compressed air into the gold containing slurry. For those ores that contain certain obnoxious substances that consume oxygen, maintaining the required minimum level of dissolved oxygen can be troublesome. One of the most economical solutions to the problem of low dissolved oxygen, especially in plants that have air compressors installed, is to enhance the rate of oxygen mass transfer. The oxygen mass transfer rate was measured in a two phase system using two different sparger arrangements, and with addition of a frother that is known to reduce the bubble size produced by the sparger. The common sparger system was shown to be inefficient compared with a readily available but under utilised method of gas dispersion which introduces air directly below the reactor turbine. Transfer of this technology to an operating plant confirmed the beneficial effect of the improved sparger system. The addition of the frother did decrease the bubble size, but it also reduced the oxygen mass transfer rate.

Jan 1, 1993

By Francisco Vitor Vasques Barbosa

Após 10 anos da aprovação da portaria 598 do Ministério do Trabalho, e ter realizado Laudo de Inspeção em mais de 60 sites industriais de grande porte, a PDCA Engenharia tem sido envolvida no processo de adequação do sistema de gestão de manutenção e operação das instalações elétricas de seus clientes. O relatório de inspeção preconizado no item 10.2.4.g da NR-10 estabelece a obrigatoriedade de se levantar os aspectos não conformes, estabelecer um plano de adequação definindo responsáveis e prazo de execução. Com os efetivos de manutenção reduzidos, nossos clientes passaram a envolver a PDCA na implementação das ações de adequação. Este trabalho consiste entre outras coisas na identificação das intervenções críticas de operação e manutenção das instalações elétricas (15 a 20 no máximo por site), analisá-las do ponto de vista dos riscos elétricos e adicionais associados a cada etapa de execução, estabelecer as medidas de controle necessárias para a mitigação destes riscos, redigir procedimentos e treinar o pessoal envolvido. Outros procedimentos devem trabalhar a eliminação dos riscos para os trabalhadores não autorizados (leigos), que interajam indiretamente em instalações elétricas e serviços com eletricidade. Apresentamos um resumo desta experiência recente com clientes da área Química/Petroquímica e da área de Logística.

Jul 31, 2018

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Beatriz Peralta Oruê

Manganese, a toxic mineral, related to manganism may have high added value for the steel industry. The difficulty in obtaining manganese encourages the exploration of new secondary sources such as the lateritic nickel effluent. In Brazil, nickel reserves are predominantly lateritic, making the country a potential producer. For the tests, a synthetic solution was used which simulates the lateritic nickel effluent from leaching. The oxidative precipitation with ozone occurred at the oxygen flow rates: 0.5; 1.0 and 2.5L/min, at the original pH 1.5 at 21°C in a 500 mL bubble column reactor. O3 was produced in the benchtop generator feed by 99% oxygen. The ozonation time was determined by the oxidation potential1.55V. The ozonated solution was centrifuged and filtered. The filtrate and collected samples were characterized in ICP-OES. Optimization tests with ultracentrifuge were performed. The best precipitation reached 97% at 0.5L/min O2 at 6.07 ± 0.045mg/min of O3 dosage and resulted in a solution 10-15mg/L Mn+2, above 1mg/L, maximum value acceptable by Conama 2011, to be retreated before being discharged into the water body or being reused as a manganese source.

Oct 3, 2019

By Claudio Pereira Diogo

Bobinas de aço laminadas a frio galvanizadas com recobrimento do cromo foram empregadas para a produção de telhas e calhas d’água. Entretanto, o fabricante destes produtos teve problemas com as superfícies obtidas, que mostraram sinais de marcas de deformação/estiramento. O problema é que, na aplicação desejada, uma aparência superficial que não seja brilhante e lisa é muito indesejável. Este trabalho foi feito a fim de descrever as condições que levaram o material para se comportar como visto pelo usuário (fabricante de telhados e calhas de chuva) com base em sua aparência e comportamento mecânico. Foram empregadas observações em microscópio estéreo e curvas tensão-deformação, obtidas a partir de ensaios de tração. Com base nos resultados, são apresentadas algumas opções para minimizar a ocorrência de marcas citadas durante a utilização do que as bobinas.

Aug 16, 2017

By Afonso Rangel Garcez de Azevedo

Este trabalhou lidou com a avaliação de amostras de tijolo de argila para alvenaria estrutural com adição de resíduo cerâmico cujas dimensões nominais são 11,5x39,0x19,0 cm. As amostras foram queimadas nas temperaturas 700°C e 800°C. Elas foram coletadas em uma fábrica de cerâmica vermelha em Campos dos Goytacazes, RJ, Brasil. De um lote, a amostra contendo 20 tijolos de alvenaria já queimada em seu forno a 700°C foi coletada, e também a amostra contendo 20 tijolos de alvenaria do mesmo lote secos apenas pelo ar, que foram queimadas em um forno de mufla a uma temperatura de 800 ° C. As amostras foram submetidas aos testes recomendados pela ABNT NBR 15270: 2005 para determinar suas propriedades geométricas, físicas e mecânicas. A ABNT NBR 15270: 2005 recomenda formulações específicas para determinar a resistência à compressão característica (fbk) da alvenaria de tijolos de argila que, para ser classificada, deve ser de pelo menos 3 MPa. Portanto, também usamos o Método Gráfico de Probabilidade e o Método da Máxima Verossimilhança para estimar os parâmetros de distribuição para comparar os resultados obtidos nos testes realizados.

Oct 30, 2017

By Thiago Pires Nagasima

O refino de grão da estrutura bruta de solidificação da liga Cu-30%Zn (latão 70/30) a partir de adições de P e Zr ao banho líquido foi investigado utilizando-se microscopia óptica, microscopia eletrônica e microanálises. Foram conduzidas medidas de tamanho médio de grão pelos métodos planimétrico e do intercepto linear e foram realizadas microanálises por espectroscopia de dispersão de energia (EDS) e de comprimento de onda (WDS). Nas amostras obtidas observa-se que, quando são adicionados P e Zr, sempre ocorre a diminuição do tamanho médio de grão em relação àquele das amostras onde apenas P é adicionado. O menor tamanho médio (? 200 ?m) ocorre para um teor de 0,16% de Zr. O refino de grão coincide com a formação de precipitados geralmente facetados, contendo Zr e P em uma proporção equivalente à da fase ZrP. Sugere-se que as adições causaram a formação de partículas sólidas de ZrP, sobre as quais ocorreu a nucleação heterogênea de grãos da fase Cu-?, resultando no refino de grão.

Oct 30, 2017