Search Documents

By A. Khan

The effect of sulfur dioxide on collectorless and collector induced flotation of chalcopyrite was studied by cyclic voltammetry on a rotating disc electrode. Contact angle measurements were made to determine the effect of sulfur dioxide concentration and electrochemical treatment. The benefits of sulfur dioxide in enhancing the selectivity of separating chalcopyrite from complex sulfide ores are discussed.

Jan 1, 1996

By V. Ross

"The Upper Group 2 (UG2) reef in the Bushveld Complex in South Africa hosts an estimated 40% of the world’s Platinum Group Metal (PGM) resources. The processing of this ore via flotation poses two particular challenges: limiting the levels of chromite in the concentrate to reduce downstream smelting problems, and enhancing the recovery of ultrafine (typically -10 micron), liberated PGMs. Conventional ways of suppressing the entrained chromite, such as froth washing, is not effective in PGM operations, which are dominated by mechanical cells. The recovery of fine particles is hampered by low collision efficiencies with air bubbles, as well as oxidised surface layers especially in tailings operations. This paper documents the results of laboratory tests on a run-of-mine PGM UG2 ore, investigating the application of a pneumo-mechanical column (PMC) and its effect on PGM flotation and its selectivity with regard to chromite. A key feature of the device is the stage-wise release of aerated slurry from an agitated downcomer, thus creating conditions where the superficial velocity profiles of air and slurry change axially within the separation zone. This aids segregation of the silicates and chromite-rich fractions in the separation zone, concentrating the latter towards the bottom of the column and minimising its entrainment into the concentrate. Comparison of the performance of the PMC to that of mechanical laboratory cells under equivalent operating conditions showed improved PGM flotation kinetics and recovery. This was accompanied by a decrease in gangue recovery compared to the mechanical cells by more than 40%, thus doubling the final rougher concentrate grade from 50 to 100 g/t. Significantly, whilst the overall Cr2O3 recovery was reduced by more than 60%, the selectivity (PGM recovery vs Cr2O3 grade in the concentrate) was doubled.INTRODUCTIONThe Bushveld complex in the northern part of South Africa hosts the world’s largest reserves of Platinum Group Metals (PGMs), representing approximately 40% of the total PGE. It is characterised by three main PGM bearing reefs, namely Merensky, Upper Group 2 (UG2) and the Platreef. The Merensky and Platreef are dominated by silicates in the form of pyroxenites, and carry economically recoverable amounts of copper and nickel, in the form of chalcopyrite and pentlandite. The UG2 on the other hand is a chromitite ore with chromite as (ideally, FeO.Cr2O3) the most abundant gangue, often constituting more than 70% by mass with a PGM grade of around 4.5 g/t. Other key gangue minerals are pyroxene, feldspar and talc. The PGEs occur in a wide variety of minerals, with platinum and palladium sulphides typically accounting for about half of the total. Base metal sulphides such as chalcopyrite, pentlandite and pyrrhotite occur in only very minor amounts, accounting mostly for less than 0.1% by mass."

Jan 1, 2018

By James S. Redpath

"AbstractThis paper is an attempt. to outline the present status of underground mining contracting in Canada, and to present certain facts concerning the writing and administration of underground mining contracts which, hopefully, may be useful to those intending to engage a mining contractor . The paper is based on the author' s experience as a contractor and also as a consulting engineer advising others in the purchase of contractors' services.HistoryIN THE early days of mining contracting in Canada, the contractor was primarily a labour contractor. He was expected to bring a good crew of men that normally followed him, and to perform certain work under his own direct supervision. The owner usually looked after all other details including financing, payrolls, withholding taxes, etc , computing and paying the contractor his profit. In the pre-World-War II years, most work was done on this basis.Over the years, the contractor was called on to supply more in the way of services, and the present-day situation evolved.Labour contracts are still used, but now the contractor is expected to carry out his own administration. Most contracts now call for the supply of special tooling required to do the work. In most cases, some, if not all, supplies are the contractor 's responsibility and , in a growing number of cases, the contractor is responsible for such items as design and surveying. The ultimate in this direction is the execution of projects on a turnkey basis. Under this system , the contractor carries the project to a stage where it is turned over fully operational to the owner."

Jan 1, 1977

By W. G. Pariseau

"BACKGROUND The Crandall Canyon Mine (CCM) is located in the Wasatch coal field in central Utah. Extensive longwall mining at CCM preceded a decision to recover coal left in barrier pillars on each side of a set of main entries extending far into the mine. During mining in March, 2007, a major bump occurred that led to cessation of mining in the barrier pillar on the north side of the mains and to begin mining in the south barrier pillar. Subsequent loss of ground control in August, 2007, through coal pillar bursts had tragic consequences with loss of six miners and shortly afterwards three rescue team members. An MSHA report describes the events in detail (MSHA, 2008). An important lesson to be learned from CCM is the need to select a computer program suitable for pillar design. Computer programs are engineering tools; selecting the right tool for the job is essential. In this regard, a minimum program requirement is capability for computing stress distribution within a pillar and adjacent roof and floor strata. The reason is simple: strength of rock is stress dependent; both vary from point to point in pillars and adjacent strata. Preferably, one should follow the evolution of stress as the mining plan is executed from start to finish to assure safety or to warn of a potentially hazardous situation developing as mining progresses. The approach to the problem posed by barrier pillar mining at CCM is conventional in the sense of applying well known finite element modeling techniques to analysis of a proposed mining plan. The engineering purpose is to evaluate the mining plan with respect to ground control questions including roof, floor and pillar safety. Results of previous two dimensional finite element analysis indicated pillar safety was by no means assured (1, 2, 3). Geometry of barrier pillar mining is limited in two-dimensions, for example, crosscuts are not seen in vertical cross sections. While three dimensional analyses are preferred, even moderately sized regions often lead to very large problem sizes that exceed computer capabilities. However, a recent development in finite element modeling of tabular deposits allows for whole mine analysis in three-dimensions. This technique involves a dual node – dual mesh concept. Both have been used separately in much earlier work, but are only now are used in combination. Estimation of subsidence at a kilometer scale and details of stress, strain and displacement about barrier pillars, main entries and pillars, and so on at a meter scale are possible (4). No compromise involving empirical formulas or similar guess work is required. Indeed, all calculations are based on first principles: physical laws, kinematics, and material laws. Effects of joints and in situ variability or uncertainty in strata properties, elastic moduli and strengths, may be included for greater realism. An important objective of the present study is to assess the role of three-dimensional pillar geometry in arriving at conclusions regarding barrier pillar mining versus two-dimensional results."

Jan 1, 2015

By H. A. Pearse

The history of the flotation process, as applied to the practical field of ore dressing, dates back somewhat less than twenty years; yet this fact may be overlooked in view of the present universal dependence on this process in the concentration of almost all classes of ore. It is therefore interesting to recall that Britannia was the scene of some of the earliest experiments with flotation on a commercial scale. In 1911, sixteen years ago, an Elmore vacuum machine was operated for several months with encouraging results. In 1913, some time before flotation was very generally adopted elsewhere, a Minerals Separation plant, capable of treating 600 tons daily, was operating successfully at Britannia. Considering how little was known of the theory and practice of flotation at that time, the recovery was remarkably good, but it was not until the present mill was completed in 1923 that any attempt was made to raise the concentrate grade by differential flotation, or, in other words, to float the chalcopyrite while rejecting the then worthless pyrite with the tailings. The first ore passed through the present concentrator in March, 1923. As originally designed, the rated capacity was for 2,000-2,500 tons, but this has been increased year by year, until at the present time 4,000 tons daily can be treated economically. During the first few months of operation the concentrate grade averaged only 10-11 per cent Cu, but by the end of 1923 this had been raised to over 20 per cent, due to the elimination of the pyrite by differential flotation. In 1923 the tailings averaged approximately 0.25 per cent Cu, but also in the matter of recovery a considerable improvement has been effected, for during the year 1926 an average tailing of 0.15 per cent Cu was maintained.

Jan 1, 1927

By A Galley, M Plouffe, T Hynes

Canadian mining research has recently been reinvigorated through a pan-Canadian research strategy driven by the industry, the research community and government departments. These organisations have come together to form the Canada Mining Innovation Council, whose role is to focus and increase mining research in the country. One of the major themes of the organisation is environment; including major research initiatives on energy, tailings and environmental stewardship. Other major initiatives on exploration, mineral extraction and mineral processing will also consider environmental benefits in the research projects they undertake. All the initiatives have their priorities determined principally by the mining and exploration companies, whose first obligation is to determine the long-term research priorities of the industry as a whole, rather than for their individual companies. Only after industry consensus on priorities does the research community become engaged in the implementation of specific projects to address those identified priorities. A goal of the program is to effectively create a virtual mining research laboratory, by engaging all the major research centres in the country. Membership to date includes most of the major mining companies operating in Canada and almost all of the mining-related universities. Other members include federal, provincial and territorial governments, consulting and service companies and manufacturers.CITATION:Hynes, T, Plouffe, M and Galley, A, 2012. A new approach to mining research in Canada, in Proceedings Life-of-Mine 2012 , pp 333-338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By C. Fortin

The subject of gold flotation has been reviewed extensively in a number of publications. The focus in most of these reviews has been on the theories of gold flotation as well as the physical and chemical effects that may impact the efficacy of the gold flotation process. It is evident that the current status of gold flotation chemistry as it is being applied in industry has not been addressed widely. It is the intent of this paper to review current gold flotation practice and how these applications tie in with the current understanding of the chemistry of gold flotation.

Jan 1, 2011

By P. Zhu

The leaching behavior of copper powders recovered from waste printed circuit boards (WPCBs) was investigated using electrogenerated chlorine and aeration in a sulfuric acid solution with added NaCl and CuSO4. Various parameters were studied to understand the mechanism of the copper leaching. When the current density increased from 0 to 0.1 A/cm2, the temperature from 30 to 60° C, agitation speed from 100 to 400 rpm, and the size ranged from below 75 to 150 µm, the leaching ratios of copper powders increased. The leaching kinetics were analyzed using a shrinking core model: 1-(1-X)1/3 = kt, and the leaching process was chemically controlled with an activation energy of 14.7 kJ/mol due to Cl- ion catalysis. The ratios of [Cu+]/[Cu2+] at various temperatures (30, 40, 50, 60 and 70° C) showed a periodic variation with the increasing of the leaching time. The redox potentials of the leaching solution and copper leaching ratios in different conditions were measured. The result indicates that dissolved oxygen achieved the dissolution of coppers and electrogenerated chlorine can promote the dissolution of copper powders and improve the reaction rate of kinetics in the presence of oxygen.

By Y. C. Kim

This paper describes the implementation aspect of a blast hole kriging system which has been developed for the purpose of daily ore-waste control in an open pit mine. The primary goal of blast hole kriging is to improve the ore-waste delineation procedure. A complete computer program package called Blast Hole Kriging (BHK) System was developed for IBM/PC AT or XT computer, using Fortran language and supplemented by a few Assembly language routines for bit-map manipulation. The emphasis of this paper is on the implementation aspect of the developed system. For this reason, the requirements for practical implementation and the system design considerations are discussed in the paper, as well as the main features of the University of Arizona's BHK System.

Jan 1, 1990

By Lev Filippov, Vyacheslav Severov, Inna Filippova

"Reverse cationic flotation is a very efficient method of beneficiation of oxidized iron ores when you need to separate hematite and quartz. This method can be also applied to reduce silica content in the magnetite concentrates obtained by wet low-intensity magnetic separation. However, cationic flotation in this case is less effective due to the presence of Fe-Mg-Al-bearing silicates as amphiboles in magnetite ores. These silicates are concentrated in magnetic products and determine the difficulties of their separation from iron oxides when amines and starches are used as collectors and depressants, respectively. The recalculation of the results of the electron microprobe analysis of three calcic Fe-Mg-Al-bearing amphiboles used to characterize cation distributions in structural units and to obtain structural formulas in accord with stoichiometric limits was conducted. The Mössbauer spectroscopy was used to examine the validity of the empirical estimation of cation distributions in amphiboles. The studied samples are metamorphic pargasite and ferrotschermakite and volcanic magnesiohornblende. The crystallographic analyses of the amphibole samples exhibited their heterogeneous surfaces explaining worse floatability of amphiboles with dodecylamine at pH 10. The electrokinetic measurements showed that the position of the isoelectric point of amphiboles is related to a substitution of Al3+ for Si4+ in tetrahedral sites and to an amount of Mg2+ cations in octahedral sites. Thus, the dodecylamine adsorption onto amphiboles through electrostatic interactions is mainly affected by a distribution of these cations in tetrahedral and octahedral sites of amphiboles. In addition, the effect of starch on the depression of Fe-Mg-Al-bearing amphiboles during flotation can be attributed to the presence of metal ions on the amphibole surface, which are capable of forming strong chemical complexes with starch molecules."

Jan 1, 2014

By B. J. Walsh

ABSTRACT Segregation of sphalerite minerals in zinc concentrates into christophite, marmatite and ordinary sphalerite by means of magnetic fractionation is investigated. A Frantz ferromagnetic filter, 1.2 amp., and a Dings magnet, 0.3 amp., is used to fractionate seven zinc concentrates produced in the Province of Quebec. The Dings magnetic product contains the pyrrhotite, and the sphalerite as christophite. The Frantz magnetic product contains sphalerite as marmatite, while the Frantz nonmagnetic product contains ordinary sphalerite. The results indicate that the magnetic susceptibility of sphalerite increases with increasing isomorphous iron content and that a satisfactory separation into christophite, marmaite, and ordinary sphalerite may be accomplished by magnetic fractionation. INTRODUCTION SPHALERITE, the chief ore of zinc, is almost never pure zinc sulphide. Iron is almost always present isomorphously replacing an ?equivalent amount of zinc. What may be referred to as 'ordinary' sphalerite contains up to 10 per cent iron. More highly ferriferous varieties, with 10 to 26 per cent or more iron, have been named marmatite .and christophite.

Jan 1, 1951

By C. H. Madsen

THE Hard Rock gold mine is in the Little Long Lac mining area, Thunder Bay district, northwestern Ontario. It is four miles by road from the town of Geraldton, which is on the Canadian National railway, 180 miles northeast of Port Arthur. The original discovery of gold-bearing quartz veins on the property was made in 1931. Shaft sinking began in the fall of 1934 and approximately 7,400 feet of lateral development on four levels was completed. In 1935, further discoveries were made half a mile west of the early workings, and the No. 2 shaft was sunk in this area in a porphyry zone. In January, 1938, a 20C-ton cyanide plant was completed and began drilling ore from the gold-bearing porphyry orebody. The daily feed was increased gradually to 300 tons in the next six months and a recovery of 97.5 per cent was effected. During the summer of the same year, a new and larger orebody was discovered to the north of the porphyry zone. It occurs in a band of iron formation and contains a high percentage of pyrite and arsenopyrite. Extensive tests were rr.ace on this sulphide ore in the Mines Branch ore dressing laboratory at Ottawa, in the laboratory of Canadian Industries, limited, at Toronto, and later at the mine, to find a suitable method of treatrr.ent. As a result of this research, a Potation plant was added to the original cyanide mill and on November 7th, 1938, differential flotation was used to separate the pyrite from the arsenopyrite fraction of the ore. The pyrite concentrate was re-ground and cyanide:l, and the arsenopyrire concentrate was stored for subsequent treatment. Differential flotation was discontinued in April, 1939, in favour of bulk formation of all the sulphides, and the whole cyanide residue was stored. On March 15th, 1939, a 10-ton pilot roaster was completed and rests were conducted on the arsenopyrite concentrate and the bulk concentrate. The results obtained led to the building of two roasters of the same type, large enough to roast all the concentrates. These roasters were put in operation on September 24th, 1939, and the calcines were cyanided in the original circuit.

Jan 1, 1941

By A. Khan

The purpose of this paper is to demonstrate the value of identifying and optimizing throughput constraints by utilizing a Constraint Model. This will be achieved by first understanding the overall concept of Operational Excellence, Continuous Improvement and Theory of Constraints as practiced within Vale Canada Limited. Next, the value of utilizing a Constraint Model is demonstrated by primarily identifying constraints. The applications in utilizing Constraint Models will be demonstrated, including the primary benefit of identifying constraints. The remainder of the paper will focus on how to properly setup a Constraint Model using discrete simulation (regardless of simulation software). Benefits of understanding the severity of constraints and movement of the bottleneck will be recognized. The paper will conclude with the summary of real applications within Vale Canada Limited.

Aug 1, 2013

By J E. Wheeler, S B. Valine, L G. Albuquerque

It has long been known that closed circuit grinding with a classifier improves grinding efficiency, reduces unit specific power consumption, and reduces over grinding. The classification device removes material from the circuit that has reached the desired size and returns coarse material back to the mill for further grinding. The efficiency of the classifier is an important factor in the overall performance of a grinding circuit. The classifier affects the capacity of the grinding circuit and the metallurgical performance of downstream operations. A review of historical research and modern case studies is used to demonstrate the benefits of high frequency screens for classification in grinding circuits.CITATION:Valine, S B, Wheeler, J E and Albuquerque, L G, 2012. Applications of fine screens in grinding circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 389-394 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By A. B. Cortes

This research work discusses the development of a two-dimensional model that represents the flow that occurs in the inlet section of hydrocyclones. The governing equations are the two-dimensional, unsteady, incompressible Navier-Stokes equations in cylindrical polar coordinates with primitive variable formulations. In this approach, no assumptions have been made other than independence in the axial direction. The full two-dimensional Navier-Stokes equation in the r-a plane is used. The commonly used simplifying assumption of axisymmetry is not used. A numerical technique based on a newly developed spectral-difference method is used to solve the equations. The spectral-difference method is a multi-domain, and multi-dimensional extension of the Jacobi polynomial collocation technique. The computational grid for the inlet section is composed of 25 sub-domains which result from five partitions in the angular direction and five partitions in the radial direction. Several test cases are used to validate the appropriateness of the numerical model.

Jan 1, 1995

By M. S. Badollet

"IntroductionAsbestos as received by the manufacturer of asbestos products is •in the •form of either crudes or milled fibres processed to different degrees of texture. Frequently, the manufacturer finds that l:ihe fibres as he buys them are not adaptable to his plant processes, and, therefore, it is necessary for him either to contact the mine supplying the material and request a specific texture for the :fibre or to reprocess the fibre in his own plant.When the mine or mill manager is requested to change his milling equipment to produce a special grade of fibre with a specific texture, he would like to comply. However, if he began to make special fibre grades for each customer, he would be in the position of constantly rearranging his milling technique, adding more equipment, or building a new mill. In the end, his mill would he producing hundreds of different fibre grades of varying degrees of texture, which is a difficult accomplishment if he desires to maintain any quantity of production."

Jan 1, 1950

By M L. Leybourne

In 2012, in response to an increasing potential unfunded liability, the Western Australian Government passed the Mining Rehabilitation Fund Act 2012. The intent of this Act was to introduce an annual levy on tenements covered under the Mining Act 1978 based on the area of disturbed land. The fund generated from these levies could then be used to rehabilitate mining sites where all other options to ensure rehabilitation had been exhausted. The fund could also be used to rehabilitate abandoned sites or features which, in Western Australia, number over 10 000.The Mining Rehabilitation Fund (MRF) was implemented on 1 July 2013 for an initial voluntary year. It becomes compulsory on 1 July 2014. By the end of March 2014, nine months into the voluntary period, over $6.5 million had been paid into the fund. The incentive for tenement holders to voluntarily enter the fund was the opportunity to have unconditional performance bonds held against their tenements retired. While there will be circumstances where bonds will continue to be applied, it is the State Government’s intention to retire most of the bonds.The MRF has received mostly accolades from industry and companies that have entered. Most have found the system easy to use. The MRF was also cited as a reason for Western Australia’s improved position in the Fraser Institute’s annual survey of mining jurisdictions. Work is now starting on processes to select priority abandoned mines for rehabilitation.This paper explains the background to the MRF and its development, and reviews its implementation during the first, voluntary, year. It also discusses how the fund will be managed into the future and what this will mean for both abandoned mine features across Western Australia and any future abandoned mine sites.CITATION:Leybourne, M L, 2014. Ensuring rehabilitation into the future – The Western Australian Mining Rehabilitation Fund, in Proceedings Life-of-Mine 2014 , pp 441–448 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By W. J. Fene

Ventilation is undoubtedly the greatest single safety factor in the operation of a coal mine. Any condition or occurrence that interrupts the ventilating current or changes its normal course through the mine workings is a distinct hazard and should be considered as such by every coal-mine owner, operator, and worker. The hazard, of course, is much greater in a mine that is emitting gas, as an explosive mixture can accumulate in a very short period if the ventilating current is interrupted. It is common to find one or more entries producing 600 cubic feet or more of methane per hour. If the ventilating current were short-circuited from these entries for 15 minutes, there would be an accumulation of 150 cubic feet of methane, which, when mixed with enough air to dilute it to the lowest explosive point, would make about 3,000 cubic feet of explosive mixture; this gas could be ignited in almost any normally operated mine by a cutting machine or other electrical equipment. The ignition of this quantity of an explosive gas-air mixture can readily cause an explosion of coal dust that would completely wreck the underground workings and possibly some of the surface structures. In fact, the ignition of one-tenth of the above quantity of an explosive mixture of gas and air might readily start an explosion that would, extend through every part of a large mine. The possibility of occurrence of interruptions to the ventilating current has received comparatively little consideration from mine owners, operators, and workers in many parts of the United States. Such a possibility should be considered in connection with every mine that gives off explosive gas, and steps should be taken to prevent it.

Jan 1, 1943

Over the last four years, a major collaboration between CSIRO-MIS, UCT and JKMRC has produced two significant advances in the modelling of comminution. The Universal Comminution Model (UCM) uses parametric SPH/DEM studies of comminution and separation devices to calibrate mathematical models which are suitable for industrial use. The Virtual Comminution Machine (VCM) uses the same computationally intensive techniques based on discrete element modelling (DEM) and smoothed particle hydrodynamics (SPH) to directly model any comminution device by combining a CAD file describing the machine design, sophisticated ore characterisation methods and advanced particle scale flow and breakage simulation. The UCM should be useful for process analysis and optimisation of existing equipment and circuits while the VCM should make a major contribution to the evaluation and development of new machines. Progress to date is encouraging with several processes now well described using DEM. This paper also reports on progress towards combining DEM for particles with a realistic slurry model based on SPH for different types of comminution devices. In due course, this combination should allow accurate modelling of particle transport in wet mills to be combined with DEM models.

Jan 1, 2014

By D H. Sharp

The Quebec Cartier Mining Company produces iron concentrate for twelve months of the year from Port Cartier. This J>Ort is designed to handle ship varying in size from 3,000 to 100,000 d.w.t., requiring 50 feet of water at low tide. The harbour was built on shore for reasons of economy and layout, after considering many more conventional offshore designs. It provides for heavy oil bunkering, tanker off-loading, a heavy lift derrick and freight handling, besides ship loading and mooring. The weather for the previous fifty years was studied to enable wind and wave conditions to be accurately assessed for design purposes, and to determine probable lost time due to adverse weather conditions through-out the year. The first ship to be loaded was 60,000 d.w.t.; the second, 20,000 d.w.t. The latter entered the harbour after dark, under its own power, following a tug through the partly dredged narrow entrance. Large ships use tug assistance. Ships may leave the loading berth with the other berths occupied.

Jan 1, 1963