Search Documents

By Guadalupe Sanchez, Roel Cruz, Sergio Castro, Claudia Beltrán, Isabel Lázaro

The recovery of zinc in refineries is strongly affected by the formation of zinc ferrites during the roasting of zinc concentrates. To achieve the highest zinc recovery most of these plants operate under high acidity and high temperature conditions in their leaching circuits. However, under these conditions high iron dissolution occurs. For iron control the common practice is to precipitate it as jarosite, and calcine is normally used as neutralizing agent. This practice causes a significant loss of metal values associated with the calcine, such as zinc ferrites and silver insoluble phases. These metal values are carried by the jarosite into confined waste in many plants. In order to diminish such losses, it is necessary to use a neutralizing agent that could substitute the use of calcine. An alternative neutralizing could be the basic zinc sulfate (BZnS). This work presents the results of a laboratory analysis on the required conditions for the BZnS production from process streams of a zinc refinery plant. Neutralizing behavior of BZnS was evaluated in iron precipitation as jarosite, in order to establish the feasibility of replacing the calcine and decrease the loss of zinc and other metals values during the iron removing step of the hydrometallurgical circuit of the zinc refinery under study.

Jan 1, 2014

By M. L. Harris, J. Organiscak, S. Klima, I. E. Perera

"The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) conducted underground evaluations in an attempt to quantify respirable rock dust generation when using an untreated rock dust and a rock dust treated with an anti-caking additive. Using PDM 3600s and 3700s, these evaluations measured respirable rock dust levels arising from a flinger-type application of rock dust on rib and roof surfaces. Rock dust with a majority of the respirable component removed was also applied in NIOSH’s Bruceton Experimental Mine (BEM) using a bantam duster. The respirable dust measurements obtained downwind from both of these tests are presented and discussed. This testing did not measure miners’ exposure to respirable coal mine dust under acceptable mining practices, but indicates the need for effective continuous administrative controls to be exercised when rock dusting to minimize the measured amount of rock dust in the sampling device. INTRODUCTION Two factors have combined to renew concern regarding respirable dust measurements and compliance. This renewed recognition is due to two regulations that have modified operators’ rock dust schedules. First, the 80% incombustible requirement in intake entries has increased both on-section and outby-the-section rock dusting. Secondly, the recent respirable dust regulation change that has increased the number of respirable dust samples taken per sampling cycle. Previously, when only 5 samples were needed bi-monthly, rock dusting could be scheduled to not interfere with the respirable dust sampling schedule. The significant number of samples now required under new regulations combined with the need to maintain 80% total incombustible content in active mining areas require the schedules for respirable dust sampling and rock dusting to intermix. This raises concerns about the amount of rock dust that potentially is included in the sampler weight gain. Additionally, the respirable dust maximum was lowered from 2.0 mg/m3 to 1.5 mg/m3 (effective August 1, 2016) increasing concern that rock dust contamination may be an issue. Currently, the acceptable practice is to apply administrative controls such as keeping the miners upwind during rock dust application or to schedule rock dusting during a maintenance shift when the number of miners present is lower. NIOSH’s research examining the quality of rock dust has led to the development of hydrophobic rock dusts."

Jan 1, 2017

By F. Melo, M. Pawlik

Fine coal aggregation in concentrated coal-water suspensions was studied through steady-state rheological measurements. The wettability of coal particles was modified by dry oxidation of a bituminous coal. The degree of hydrophobicity was monitored using film flotation. The rheological measurements revealed that hydrophobic coal particles aggregate in aqueous suspensions, over a wide pH range, and produce slurries with high yield stresses. As the degree of coal oxidation increases, the coal particles become more hydrophilic and such suspensions exhibit lower yield stresses values. The yield stress values for suspensions prepared from oxidized/hydrophilic coal become a strong function of pH and correlate well with the surface charge as determined through electroacoustic measurements. These results indicate that the yield stress of aqueous suspensions of coal, and hence coal particles aggregation, is strongly affected by the wettability of coal particles.

Jan 1, 2004

By Jeffrey D. Oke

While significant progress in underground construction engineering has occurred in the past few decades, a number of fundamental deficiencies persist regarding the recognition, prediction, and mitigation of underground construction hazards associated with complex geological conditions in rock and soil works, such as tunnelling. Many of these shortcomings could be addressed by improving geomechanical models which, in turn, would provide more realistic frameworks for determining input parameters for design analysis. This would improve predictions of construction efficiency for tunnelling and the formulation of more accurate modelling techniques (2D, 3D and 4D) required to optimize the design of engineered rock structures. This research focuses primarily on the issues related to forepole temporary tunnel support within weak rock masses. This research attempts to determine how best to numerically model forepole support. The behaviour and mechanics of forepole support has not been quantified and/or optimized. As well, there is a lack of in-situ and/or laboratory forepole and weak rockmass interaction parameters available. In terms of numerical modelling, there is a lack of understanding of the use of proper interaction parameters associated with the forepole and the rockmass. The parametric study that has been conducted by the authors demonstrates the influence of each of the forepole-rockmass interaction parameters and their sensitivity. Introduction

Jun 1, 2012

By Michel Épiney, COREM, Mario Drapeau, Caroline Olsen, Claude Bolduc, Benoit Levasseur

"Several metal sulfide minerals (such as copper, zinc and iron), generally abundant in precious metal-containing ores, are known to dissolve during the cyanidation process. These unwanted reactions consume a significant amount of cyanide and oxygen, which is required for the extraction of gold and silver. Leaching kinetics of sulfide minerals are very fast in contact with oxygenated cyanide solutions. Therefore, the solution quickly becomes charged with oxidation products that are mostly metal ions, metallo-cyanide complexes, metal oxides and other sulfur species including thiocyanate, sulfides, polysulfides, thiosulfate, sulfites, sulfates, etc. COREM’s Extractive Metallurgy team has been conducting a research program on the improvement of the gold cyanidation process. As a part of this program, the current study aims to investigate the effect of certain operating parameters on the reactions involved during pre-oxidation and cyanidation. The effect of pre-treatment under ozone was investigated using an industrial pulp recreated from process water (charged with thiocyanates) and homogenized flotation tailings material from Agnico Eagle's LaRonde mine. In terms of mechanisms, the ozone treatment provides a complete deactivation of the material surface (characterized by EDTA extraction) and the solution (characterized by Ionic chromatography). This resulted in a lower reactivity of sulfide minerals that led to substantial gains in terms of consumption of cyanide and thiocyanate formation during the cyanidation process. The ozone-pre-treatment edges the classical pre-oxidation treatment (such as oxygen, hydrogen peroxides, etc) providing a quicker deactivation of the sulfide matrix and higher reagent savings in subsequent cyanidation process.INTRODUCTIONThe presence of sulfur in the process of gold leaching by cyanidation is a major drawback to optimizing the reagents consumption with suitable operating conditions. The coexistence of sulfide mineral species, such as pyrite, chalcopyrite, pyrrhotite or sphalerite along with the gold-bearing ore have, indeed, a negative impact on the extraction of precious metals by cyanidation (Bayat et al., 2003), (Azizi et al., 2010). These minerals are known to dissolve with cyanide under alkaline conditions and release in the slurry different kinds of sulfide by-products like polysulfides, thiosel, sulfite and sulfate (Seal II & Hammarstrom, 2003) (Breuer et al., 2008a), (Marsden & House, 2006) (Ghasemian Langeroudi et al., 2013). Once these sulfide by-products are released in solution they react with cyanide to form thiocyanate (Marsden & House, 2006) (Breuer et al., 2008b). The consequence of the dissolution of these cyanicides, is a significant increase in cyanide consumtpion as well as a slow-down of gold extraction."

Jan 1, 2016

By Mateus Luiz Gamba

O titânio e suas ligas são aplicados em grande escala em implantes ósseos por apresentarem excelentes resultados de biocompatibilidade. No entanto, ainda não existe um consenso na literatura com relação à influência das características morfológicas destes implantes na osseointegração, principalmente na definição da melhor rugosidade e energia superficial. Vários trabalhos têm sido realizados com o intuito de comparar diferentes tratamentos superficiais empregados para otimizar a adesão, o crescimento e a proliferação celular. O presente trabalho tem como objetivo apresentar uma base de dados sobre características superfícies versus osseointegração para experimentos de biocompatibilidade realizados in vitro. Foram feitas coletas e análise de dados qualitativos usando métodos analíticos em artigos científicos publicados em periódicos internacionais, sendo considerados na pesquisa artigos que utilizaram superfícies de Ti/TiO2 e células osteoblásticas. Os principais atributos definidos para a base de dados foram rugosidade, tamanho da célula, energia da superfície e/ou ângulo de contato, tipo de tratamento superficial, viabilidade e a resposta observada na cultura celular. Espera-se que esse artigo contribua para que futuros trabalhos possam utilizar métodos e estudos que permitam auxiliar na descoberta de conhecimento através de padrões que acelerem o processo de osseointegração impactando diretamente na recuperação do paciente implantado e na sua qualidade de vida.

Aug 8, 2018

By D. E. Deegan, G. Holcroft, T. P. Johnson

"The rising cost of extracting metals from existing traditional deposits, increasingly stringent environmental regulations and a greater awareness of corporate social responsibility issues are all factors in stimulating the examination of mine tailings and small-scale alluvial deposits as a potential source of new raw materials. Furthermore, despite tougher economic times the demand for commodities remains strong, in no small part as a result of the growth of the world’s emerging economies.This combination of social and economic factors looks set to continue in the long term which will encourage greater recovery of materials from previously ignored sources such as mine tailings and ores from alluvial deposits.An expansion in the recovery of useful materials from mining-related activities is likely to require the use of robust and innovative techniques that have a built-in degree of future-proofing; DC plasma technology is one such technology.As a result of its ability to separate the valuable metal and minerals from the waste material while destroying hazardous compounds, Tetronics’ DC arc technology offers an alternative approach to resource recovery from a wide range of mine ores. Harmful cyanide compounds and the vast quantities of water used in conventional hydrometallurgical processing are avoided when plasma processing is adopted. DC arc technology also brings additional benefits, including: the extremely effective destruction of organic materials, the conversion of the inorganic material into a re-useable aggregate and the high tolerance of the process to fine and dusty materials. This paper presents details of Tetronics’ DC arc technology as one of the key pyro-metallurgical solutions available for the recovery of valuable materials from traditional mine ores and tailings, as well as giving specific examples of how the technology has been successfully employed in the recovery of enriched slags, ferroalloys and other metals."

Jan 1, 2016

By G. W. Norval, V. G. Papangelakis, G. A. Moldoveanu

Smelting has been the primary method of treatment for refractory copper sulfide concentrates such as enargite (Cu3AsS4), but the pyrometallurgical processing generates elevated levels of volatile arsenic. The present research investigates a novel hydrometallurgical process of oxidative dissolution of enargite at ambient conditions in the presence of chlorine dioxide (ClO2), a very powerful oxidant generated in solution by the reaction between a strong acid (HCl or H2SO4) and sodium chlorite (NaClO2). The effects of initial oxidant concentration, particle size, agitation speed and temperature on dissolution kinetics and copper extraction were investigated. It was found that a stoichiometric ratio of ClO2:Cu3AsS4 = 9:1 were needed to completely and congruently dissolve the mineral with fast kinetics (<15 minutes) under ambient temperature. The dissolution extent (metal extraction) increases with increasing ClO2 concentration and decreasing particle size of solids, but is not influenced by temperature or agitation speed.

Jan 1, 2014

By Francis Martino

There are numerous techniques and predictive models used by geologists and mining engineers to define coal reserves and plan mines. The traditional reserve estimation methods commonly used include the isopach, triangular, polygonal, inverse-distance weighting, weighted-moving-average, and trend-surface methods. Geostatistically-based estimation techniques are now being examined by many geologists and mine planners as a superior alternative to these traditional methods. With today&apos;s coal mine development costs often exceeding $100 million, and power generation $1 billion, it is logical that a technique that can indicate the degree of confidence associated with a reserve estimate (fuel supply), and thus also the degree of risk, is highly desirable to the coal producer, the financiers, and those desiring to commit to coal utilization under short or long-term supply arrangements.

Jan 1, 1983

By Félix Lewandowsky

El presente texto describe las actividades para corregir los pasivos ambientales heredados y asumidos bajo responsabilidad de la Compañía Minera Colquirrumi S.A. Para ello, se elaboró un plan de cierre de los cuatro depósitos de los relaves de Hualgayoc donde se busca mostrar los criterios utilizados, los estudios de ingeniería y la forma cómo se ejecutaron las obras de cierre definitivas de los depósitos de relaves.

Jan 1, 2015

By Brian D. Barkauskas, Terence P. Holman

A major combined nuclear and coal-fired power plant, located in on the western coast of Florida has undergone multiple upgrades in recent years to increase power output and enhance environmental controls. Construction of new elements within the existing plant structure required working in highly congested conditions and heavy crane lifts with large picking radii. The largest crane pick involved the use of an 1800 metric tonne capacity Mammoet PTC ring crane for a single long-radius, high altitude lift of a precipitator unit. Original bid tender documents had called for drilled shaft foundation support, but the presence of many critical utilities and unfavorable access for cost effective construction led specialty contractor Moretrench American Corporation to propose an alternate micropile foundation on the basis that high capacities could be achieved in the weak limestone geology and that the smaller size of micropiles would allow for more surgical installation in the utility-congested areas. This case history describes the design and construction of seventy three (73) high capacity micropiles for the value engineering alternative and the crane foundation for this critical lift. Each micropile was founded in a competent dolomitic fossiliferous limestone unit at typical depths of 23 m below existing ground surface. Strain gauge instrumented load testing was used to validate the geotechnical design parameters in the weak limestone bedrock and resulted in the finding that the entire test load was being carried in the upper half of the bond zone. Construction of the production micropiles required numerous relocations due to utility conflicts and local reanalysis and redesign of the 1.2 m thick reinforced concrete ring beam cap. Crane foundation performance was satisfactory and the effective life of this temporary foundation was only 6 months before decommissioning and demolition.

Jan 1, 2017

By W G. Brese

The attention of the world is being focused on the spectacular rise of elemental sulphur production in Alberta. In the short space of a decade, production has increased from less than 10,000 long tons, in 1952, to al-most 1,000,000 long tons in 1962. Moreover, 1963 sulphur production is expected to rise by 50 per cent to approximately 1,500,000 long tons, and further increases are forecast for ensuing years. The reason for this dramatic in-crease in elemental sulphur production, particularly in the last year or two, is that Alberta elemental sulphur is recovered in association with the production of sour natural gas. When very large volumes of natural gas began moving to U.S. markets in the latter part of 1961, the resultant increase in sour gas production led to a marked increase in the production of sulphur. Consequently, Canada, mainly on the strength of sulphur produced in Alberta, will soon become the second largest producer of sulphur in the Free World

Jan 1, 1963

By L Bergin, D J. Williams, S Islam, T A. Vangsness

The flooding of open strip coal mines in the Bowen Basin and Hunter Valley Coalfields of Eastern Australia has the potential to soften the spoil and floor materials to produce “mud”. This mud can act as a slip plane or weak zone when spoil is dumped into it, resulting in geotechnical instabilities. Once mud has formed, typical handling techniques include its costly removal by mechanical means, or its isolation and capping.There are little data available on the moisture state and shear strength of the capped mud. To investigate the effectiveness of isolation and capping, research has been conducted using a large slurry consolidometer (150 mm in diameter by up to 410 mm in height) to simulate capping in situ. Once consolidated, the mud was subjected to shear strength testing in a direct shear box measuring 60 mm by 60 mm by about 20 mm high. The shear strength of the consolidated mud was compared to that of competent, fresh spoil, a mixture of spoil and mud, and to completely degraded spoil (mud alone).These results have been used as inputs in stability calculations using the commercial computer program Slide 7.0, which demonstrates the strong influence of consolidation of the mud on overall low wall slope stability. The results provide insight into the design and construction of capping to isolate in-pit mud.CITATION:Vangsness, T A, Williams, D J, Islam, S, Smith, A and Bergin, L, 2018. Consolidation and shear strength testing and stability analysis of coal mine spoil degraded to mud, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 97–109 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By G. H. Long, D. H. Magnusson

THE DEFINITION of the continental margin, as considered in this paper, is in the broad sense: " ... those provinces of the continents and of the oceans which are associated with the boundary between these two first-order features of the earth" (Heezen et aL, 1959, p. 17). The provinces in the area under con-sideration are: the Continental Shelf, the Continental Slope and the Continental Rise. The Continental Shelf extends from the shoreline to the shelf break, which lies at approximately the 200-meter isobath through-out the region (except north of the Grand Banks, where the break may be defined more properly by the 400-meter isobath). The Continental Slope and Rise occur between the shelf break and the 4,000-meter isobath. (The last figure was somewhat arbitrarily selected for the purpose of this paper.) The Atlantic Continental Margin as thus defined extends along the eastern coast of Canada from the International Boundary in the Gulf of Maine northward to approximately the 60°N latitude off the coast of Labrador. The area of study amounts to at }east 500,000 square miles -an area roughly equivalent to 13 per cent of Canada's total land surface.

Jan 1, 1970

By A. S. Ibrado, D. W. Fuerstenau

"Gold, silver and copper form various complexes with cyanide, of which only the singly charged dicyano form adsorbs appreciably on activated carbon. The adsorption of the dicyano complexes appears to be controlled predominantly by chemical reaction at the surface of a shrinking unreacted core. Metal uptake over time is non-linear, which eliminates control by boundary layer diffusion. The rate of adsorption is not enhanced by a reaction interruption, which suggests the absence of concentration gradients in the pores. Finally, the rate of adsorption increases with decreasing activated carbon size in a manner consistent with the shrinking core model. The results of this investigation accentuate the importance of efficient acid washing of carbon and removing carbon fines from the barren carbon stream. INTRODUCTION With the dwindling reserves of high-grade ores, most of the world’s gold is produced from low-grade ores by cyanide leaching. In the past, leaching was followed by the Merrill-Crowe process, in which gold is precipitated from clarified pregnant solutions by zinc cementation. This process is still being used for high-silver ores, where the cost of carbon stripping becomes prohibitive. For deposits with silver-to-gold ratios of about 4 or less, adsorption on activated carbon would be the usual solution purification step taken. The process simplifies solid-liquid separation and offers a viable solution to preg-robbing organic carbon in some ores. The modern industrial application of carbon adsorption started with the carbon-in-pulp (CIP) process, where carbon adsorption was used mainly as a solution purification step. In 1973, Homestake Mining Company commissioned the first large-scale CIP plant in the U.S.A.1 Later, carbon was added earlier in the circuit to control preg-robbing by adsorbing gold cyanide onto activated carbon as soon as it is dissolved. The scheme is successful because activated carbon is a stronger adsorber than the organic carbon found in preg-robbing ores. This process came to be known as the carbon-in-leach (CIL) process. Numerous research investigations have been performed on the chemistry involved in the CIP process, which at the time of its introduction was not clearly understood. Of these, research on the kinetics of adsorption probably bears the most immediate impact on industrial practice,2,3 where adsorption systems rarely reach equilibrium, if at all, and slight slowdowns in the adsorption rate can translate into significant decreases in revenue. To illustrate this, organic compounds, like flotation reagents, have been known to impair CIP circuits. However, laboratory tests showed that the organic compounds do not significantly affect the adsorption capacity of activated carbon. Rather, the harmful effect may be attributed to a lowered adsorption rate.4,5 Also well known is the faster rate at which fine activated carbon powders reach equilibrium compared to coarse activated carbon, even though the final (equilibrium) amount of material adsorbed per unit weight is the same."

Jan 1, 2015

By C. W. Smith

Research was conducted to evaluate the effectiveness of a well-point dewatering system in conjunction with a french drain to intercept waste impoundment leakage while reducing the volume of waste water requiring treatment. A well-point dewatering system composed of 585 production wells was installed around the perimeter of a leaking impoundment that previously used only a french-drain system for leakage control. The placement of the well-point system was designed to intercept and remove the leakage from the groundwater before the contaminant reached the french drain. Groundwater monitoring at this site revealed that after a period of approximately 40 days the well-point dewatering system had stabilized and effectively prevented the further spread of contamination to the french drain.

Jan 1, 2010

By Y. C. Guan

The dissolution behavior of silver and copper form their elemental states and Ag/Cu alloys in ammoniacal solutions has been studied using rotating disc electrodes. The variables studied included concentration of ammonia, oxygen partial pressure and rotating speed of the disc. The results have been interpreted in terms of the mixed potential theory. The effect of local current resistance on the overall current has also been examined as a part of the governing theory of the dissolution. It was observed that the dissolution potential and the rate of dissolution were very much affected by the composition of the alloys.

Jan 1, 1995

By S. Carsten, S. Subramanian, R. Vasant Kumar, S. Vimalnath

"The effect of EPS components namely protein, polysaccharide and biosurfactant purified from Pseudomonas fluorescens was investigated for the bioremediation of Pb(II) ions in aqueous solution. Two parameters, namely the amount of EPS component and the concentration of Pb(II) ions were optimized for maximum Pb(II) ions uptake. The EPS components interacted with Pb(II) ions were characterized using energy dispersive X-ray analysis (EDAX) to ascertain the presence of Pb and by attenuated total reflection-Fourier transform infrared spectroscopy (ATR–FTIR) to reveal the functional groups involved in Pb(II) binding. The maximum Pb(II) binding capacities of protein, polysaccharide and biosurfactant were found to be 11.4, 0.55 and 0.11 mg mg-1 respectively. The biosorption processes followed the Langmuir model. The Gibbs free energy (?G0) values of -23.6, -20.9 and -23.2 kJ mol-1 for Pb(II) biosorption by protein, polysaccharide and biosurfactant respectively, attested to spontaneous, chemisorption processes. The ATR–FTIR results revealed the presence and involvement of amino, hydroxyl, carboxyl, phosphate, and methyl functional groups in Pb(II) binding and EDAX analysis confirmed the interaction of Pb with EPS components. The Pb(II) binding mechanisms of EPS have been discussed. The results demonstrate the potential of the purified EPS components of P. fluorescens for removal of Pb(II) ions from aqueous solution INTRODUCTION Waste water containing toxic metals from various industries pose a serious threat to human health and ecosystem. For treating such waste water, conventional methods like chemical precipitation, coagulation, evaporative recovery, electrodialysis, floatation, flocculation, ion exchange, reverse osmosis, nanofiltration, ultrafiltration are used (Lakherwal et al., 2014). These methods have some disadvantages like toxic sludge generation, incomplete metal removal and high cost (Singh and Gadi, 2012), necessitating the search for cheaper and efficient alternative methods. Bioremediation is one of the emerging alternatives where bacteria, fungi, yeast, algae and other biological substances are used as sorbents to remove toxic heavy metals (Vijayaraghavan, et al., 2015). Recently, the bioremediation potential of extracellular polymeric substances (EPS) of microbial origin has attracted attention. However, for Pb(II) removal, there is a paucity of literature focusing on EPS."

Jan 1, 2018

By Douglas H. Bolton

In recent years, equipment manufacturers have been busy developing remote control systems to catch up with the sophistication and efficiency of continuous miners. Now the tables are turned, and manufacturers are undertaking the new challenge of upgrading, refining and equipping continuous miners to take full advantage of the capabilities made possible by modern, successful remote control systems. Because the operator can safely advance the miner farther without pulling out for roof bolting, continuous miners now need to be equipped with means of complying with correct face ventilation, dust suppression, methane detection, diffusion and improved lighting. Some of the exciting possibilities being developed to catch up with remote control include feedback controls using laser beams as datum points, coal sensing devices with feedback signals to show the operator what the machine is doing, show where it is relative to the coal seam, how hard it is working, and more sophisticated use of cyclic control. Mining machinery manufacturers have accepted the new challenges, and faster, safer mining procedures are already in sight.

Jan 1, 1975

By John B. Umhau

[This !m-i~!.al survey giver, statistice.1 data res;?~dirf ~:rimay ard ?eco~- dqr or scmn tin used in thL: United St,ztas by industries an? incluclcz d;ta on stop&apos;ics, ~urchares, ard plnrt losr.c.5. It is :i ml:anwe of consq~tion in terms of fir.is1icd -prcd.~cts nz6.e iry initid ti11 Sabric:,.torc,, that is, aon- cerns that purchzse virc,in zni s~col~d&apos;l~y i.i.5 ti:; 01&apos; tin c;cra.. rav materi,als ar,d co:lrrert them into !ror?ucts such F!: ti:i plz.te, ~lloyr;, and. c?hemic?ls; comy~nias ;~urchn.&apos;.ii~; alloys, ch:rr.ic,~l::, or tin vl?.tc fcr furthcr a:mflzc- ture ?rc: ~-.f>t i~ci~~dcd. Tilit r~lqe:;tionrr::ire submit tod to consunern ar,nt:incd no dofinition of rnr.oncl.:ryr me$.-i; but, ovrirq to ti~i-: a~counti~ procedure used s.l~o~c-:t 1&apos; thu scrnn hac i~-.rtergol:e ch?rri?~ of ovinerzhip or titlo, thc rc!coverod t! n !its b~en i-c<;,r(it.!rj L.S r,e~3r;d:q met.1. Tbv tin content ~f ]

Jan 1, 1938