Search Documents

By P J. Vardon, L A. van Paassen, Y Yao, A F. van Tol

Thin-lift atmospheric fine drying (AFD) is a technique used to dewater mine and oil sand tailings, which utilises both self-weight consolidation and atmospheric evaporation. The disposed layers undergo a cyclic drying and rewetting process due to precipitation and deposition of additional lifts on top of the dried layer. The current research aims to optimise the deposition process via use of a numerical model and realistic atmospheric conditions, including both periods of drying and wetting. The model is based upon water balance and includes large strain considerations. A number of material behaviours are characterised using empirical fitting curves based upon laboratory measurement of material characteristics, including both the shrinkage and water retention curves for drying and rewetting. The model is able to model multiple lifts, simulating field scale and realistic climatic conditions within timescales suitable for engineering practice (eg seconds or minutes). The model has been previously validated against controlled laboratory experiments and utilised to simulate field tests. A series of simulations are presented to illustrate the ability of the model to be used as a practical tool for the optimisation of a tailings deposition strategy.CITATION:Vardon, P J, Yao, Y, van Paassen, L A and van Tol, A F, 2015. The use of a large-strain drying and consolidation model to optimise multilift tailing deposits, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 263–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By W. J. Kempson

In recent years, substantial progress has been made with respect to the definition and control of the primary energy requirements in underground mines. Little has, however been done to develop a more detailed understanding of how to limit the various pressure losses which are intrinsic to shaft systems. This is in spite of the fact that more than half of the pressures generated by the ventilation fans in deep level mines are dissipated as pressure losses within the shaft system. This paper presents research which has been completed to optimise the pressure losses which occur in shaft systems as a result of the ventilation air flowing through them. In this regard, the response of various shafts to the ventilation air flowing through them was measured. These results were evaluated against the current theory for the calculation of shaft pressure losses. Finally the results of the measurements and calculations were used to calibrate a Computational Fluid Dynamics model of the shaft systems. This model was then iterated to allow meaningful conclusions as to the specific make up of the shaft equipment which contributes the most to pressure losses in shaft The results of the above analysis demonstrated that the current theory used for the evaluation of these pressure losses is deficient. The paper discusses these conclusions and the specific ramifications of the analysis. Finally, the understandings gained with regards to the above research are applied to the design and layout of equipment in mine shafts. In this regard, the shape and orientation of the shaft steelwork is evaluated and it specific interaction with the piping and conveyance is evaluated. Coming out of this evaluation are specific recommendations for the design of future shaft systems. These recommendations are based on the above models and offer specific savings on the lifetime operating costs of shaft systems.

Aug 1, 2013

By J. Aiello

"Introduction Byron Creek Collieries Limited Corbin mine is located in southeastern British Columbia approximately 180 air kilometres southwest of Calgary (Fig. I), twenty four kilometres south of Highway No. 3 via a newly constructed provincial road (Fig. 2). The development of the area began July 30, 1905, when D.C. Corbin, a prominent businessman from the northwestern U.S., and his associate E.J. Roberts first visited the site of Coal Mountain on horseback. Coal was in great demand by railways and other industrial users, so the Corbin Coal and Coke Co., after acquiring 6,000 hectares of land in the area, began to develop a mine. Mr. Roberts was responsible for the construction of the 22-kilometre rail spur, the Eastern British Columbia Railway, which joined the mine to the CPR main line at the McGillivray Loop. Rail access to the mine and its developing community, Corbin, B.C., was completed in September 1908, the same year that the first underground mine began production. The Corbin Coal and Coke Co. operated six mines on Coal Mountain (Fig. 3) and production from 1908 to 1930 inclusive totalled 2,120,800 tonnes. This production was allocated to the mines as follows:"

Jan 1, 1985

By S. Stuurman

Inorganic acids such as sulphuric acid have found use together with certain reducing agents in leaching of copper-cobalt oxide ores. These reagents are not ideal due to the adverse effect the inorganic acids generally have on the environment and the high costs of the reducing agents. In this study a copper-cobalt oxide ore from the Central African Copperbelt was leached in two different environments; sulphuric acid in conjunction with hydrogen peroxide as a reducing agent and tartaric acid. The effects of acid concentration, reducing agent concentration, and temperature were independently determined for both leaching environments. The sulphuric acid concentration was varied between 0.4 M and 1.2 M and the concentration of hydrogen peroxide between 4.0 M and 6.5 M, while the tartaric acid concentration was varied between 0.15 M and 0.35 M. The temperature was varied between 20°C and 50°C. The results showed that the extraction of both copper and cobalt increased with sulphuric acid concentration, reaching a peak at approximately 0.8 M and then decreasing at higher acid concentrations. A similar increase and decrease in metal extraction was observed when the reducing agent was increased. In leaching with tartaric acid, the extraction of cobalt was much higher than that of copper, although extraction of both metals increased with acid concentration. Additions of small amounts of hydrogen peroxide were found to increase cobalt extraction in tartaric acid but had a minimal effect on copper. An increase in the solution temperature had a significant effect in the organic acid environment, with the effect on cobalt extraction being much more pronounced than on copper.

Jan 1, 2014

This report presents a Bureau of Mines study comparing the construction costs, leakage measurements, and predicted performance of different types of large stoppings built and tested in a room-and-pillar oil-shale mine. The six full-sized structures (30 ft high by 55 ft wide) included both permanent and temporary stoppings and were fabricated using materials ranging from structural steel to coated brattice cloth. Leakage across each stopping was measured at differential pressures ranging up to 1.0 in w.g., using both the brattice window method and sulfur hexa-fluoride (SF6) tracer gas. Blast air pressures resulting from a full-scale face blast of approximately 1,800 lb of ammonium nitrate-fuel oil (ANFO) explosives were measured across two of the stoppings and the pre-and post-leakage rates were compared for all the stoppings. Overall performance of the stoppings for production applications was evaluated using an operational model of a two-panel oil-shale mine. Different combinations of temporary and permanent stoppings were evaluated based upon ventilation performance and construction and operating costs.

Jan 1, 1988

By M. H. Leite, R. Corthésy, D. E. Gill

"La connaissance des contraintes naturelles qui prévalent dans les massifs rocheux est un prérequis indispensable pour la conception sécuritaire et économique des excavations comme on en retrouve dans les exploitations minières souterraines. Certains chercheurs se sont attardés à colliger les résultats de mesures de ces contraintes et les ont utilisés pour produire des modèles de prédiction basés sur leur traitement statistique. Ces modèles de prédiction sont très populaires auprès des exploitants miniers puisqu’ils permettent, du moins dans les étapes préliminaires de design, d’obtenir de façon s’apéconomique mais approximative, une partie des paramètres dont ils ont besoin. Dans le cadre d’un projet initié en 1994 avec la collaboration de l’IRSST, il a été décidé de produire un modèle de prédiction englobant une partie de la zone périphérique de la faille de Cadillac, soit une zone plus restreinte que le Bouclier Canadien utilisé jusqu’ici comme région pour l’élaboration de tels modèles. Pour produire ce modèle de nouvelles données obtenues avec une technique permettant d’exercer un excellent contrôle de qualité ont été ajoutées à celles déjà disponibles. Une telle régionalisation des données de base permet d’obtenir un modèle où les intensités et les orientations des contraintes principales sont beaucoup moins dispersées que ce que rapportent les modèles publiés jusqu’à ce jour. Enfin, il est démontré que le modèle proposé pour la région étudiée est en toute probabilité plus sécuritaire que les modèles plus généraux publiés à ce jour. Knowledge of the in situ state of stress existing in a rock mass is essential to the safe and economical design of underground mining excavations. Prediction models have been published, based on the statistical treatment of stress measurement results. Such prediction models are very popular among mine operators because they allow them, at least at a preliminary design stage, to economically obtain part of the information needed, even if this information is approximative. In 1994, a research project financed by IRSST was initiated aiming to produce a prediction model that would comprise a peripheral zone around the Cadillac fault. This region is more confined than the Canadian Shield on which the existing prediction models have been based up to now. In order to produce such a model, existing stress measurement results have been used in conjunction with new stress measurements that have been performed based on a technique which allows full control of the quality of the measurements. Restricting the data upon which the model is based to a more specific region gives a model in which the intensities and the orientations of principal stresses are far less scattered than the results published to date. Finally, it is shown that the proposed model is probably safer for the studied region than the models previously published."

Jan 1, 1998

By Robert F. Conley

Attrition milling, once employed exclusively for the dispersion of pigments, has in recent years found a host of new applications in the area of mineral processing and mineral-pigment production. Broadly categorized, attrition milling is divided into two classes, as defined by the machinery's function, vibratory milling and rotational milling. Each mill type has been defined as a variation on ball milling and the terms, "vibratory ball mill" and stirred ball mill" appear in the literature. The primary design differences between attrition and ball mills are: (1) a stationary canister (or shell) (2) smaller grinding media (3) grinder energy is motor limited rather than gravity limited (4) strong media/feed size dependance.

Jan 1, 1983

By O. F. Brown

Excavation and loading are primary operations in the surface mine production chain, constituting a significant component of production costs. This makes excavation and loading important cost centers that need to be improved to lower production costs. Optimizing the design and use of excavators will improve energy efficiency in earthmoving operations, and this requires a thorough understanding of the soil-tool interaction process. Modeling the interaction process accurately is the key to this optimization. Experimental and analytical methods have provided limited information on the behavior of soils during excavation. Finite element (Fe) analysis of soil-cutting blade interaction produces some advantages over experimental and analytical methods. However, the soil constitutive equations used in most of the available Fe analyses fail to adequately model the plastic behavior of the soil. This work uses Fe modeling to study the behavior of formation-cutting blade interactions in dozer excavation. The formation is modeled as a nonlinear elastoplastic material using the modified cam-clay (mCC) model. The model accounts for soil-tool interface friction, and progressive and continuous cutting at the blade tip. The results provide soil forces, a progressive developed failure zone and soil displacement fields. The sensitivity analysis of changes in blade angle on cutting force shows that the cutting force increases with increasing blade angle. The cutting depth of the blade had a similar effect on blade cutting force. Increasing the depth of cut increases the required cutting force. Increasing the coefficient of friction at the soil blade interface increases the blade cutting force. Reducing the coefficient of friction at the soil blade interface from 0.3 to 0.05 reduces the cutting force by 22.3%. The percentage represents the maximum potential savings in blade cutting force. This research initiative advances the frontiers of soil-tool interactions during excavations to expand the limited knowledge in this critical area.

Jan 1, 2012

By Renan Barrio de Mendoza

"El presente texto señala la aplicación de nuevas tecnologías conceptos para reducir u optimizar el consumo de energía, como los costos de operación en los procesos metalúrgicos. Así, el uso eficiente de la energía en la actividad minera tiene su impacto en la sociedad -en tanto se emplee adecuadamente en las etapas del tratamiento del mineral. Cabe recordar que en las operaciones de reducción de tamaño de partículas es más barato volar que chancar, así como chancar que moler."

Jul 1, 2015

By René Winand

The paper gives a synthesis of research work performed in the department during the last ten years and dealing with cobalt , copper and manganese electrodeposition in chloride aqueous solutions. Special emphasis is given to electrocrystallization. For copper, properties of the electrolyte such as solubility limits, electrical conductivity and complex ions stability are discussed in connection with leaching, purification of the electrolyte, and metal recovery. When possible, kinetic parameters and probable electrode mechanisms are given. Problems that are still to be solved are also listed.

Jan 1, 1985

By J. A. Brusset

Introduction I am indebted for most of the information in this paper to Mr. P. S. Lea, Deputy Chief Inspector of Mines of Great Britain, and Mr. A. E. Crook, Engineering Inspector of Mines, Ministry of Fuel and Power. Other coal-mining men in Canada may be as surprised as I was to learn that there are twenty-five Diesel locomotives in service underground in British gassy coal mines. Many more are in use underground in non-gassy coal mines and in metal mines. Approval has been granted for an additional fifty flame-proof locomotives to be used in gassy mines, and these should be in operation by the end of 1946, or as soon as manufacturing facilities permit.

Jan 1, 1946

By H. Kiyama

In order to further elucidate the mechanisms involved in autogenous grinding, the fracture of rock specimens in free-fall impact was studied using the theory of elasticity. Stress distributions in rock specimens under various conditions of impact were analyzed and the conditions for failure were examined in relation to the compressive and tensile strength of rock. The energy equation derived for autogenous grinding coincides basically with Lewis' generalized formula or Oka and Majima's formula, and it is sufficiently general to incorporate all of the three older theories, viz; those of Rittinger, Bond and Kick.

Jan 1, 1972

By Juan Ayza

En este último artículo se describe el sistema de IMPINGER - como parte del muestreo y así determinar la cantidad de polvo adherido. Dicho sistema produce una presión negativa sobre el agua de un tubo, y es donde la presión atmosférica introduce el aire por un tubo central, cuya boquija está debajo del agua y a 5 mm. del fondo. En ese sentido, la mayor cantidad polvo queda en suspensión. De otro lado, se describe el método cualitativo cinematográfico donde se percibe la cantidad de polvo a través de la captación de luz fotográfica, aunque el problema es el avaluúo preciso de la sílice li-bre en el rango de polvo respirable.

Mar 1, 1956

By Charles B. Manula

This paper describes the development of a mathematical model for simulating the behavior of a longwall coal production system. The longwall simulator is a design simulator incorporating both deterministic and stochastic methods to calculate: (a) the size and density of support; (b) the cutting force, power requirements and haulage speed for the loader-shearer; (c) the conveyor size, speed and power requirements; and (d) delay generation at head and tail-gates and the longwall face.

Jan 1, 1978

By M. Candia

"El presente trabajo describe la utilización del método de corte y relleno descendente en la explotación en la mina Yauricocha. Los métodos convencionales utilizados fueron los de cobre, corte y relleno, etc, siendo aplicables hasta 1848. Posteriormente se utiliza el método de corte y relleno descendente en el minado de ciertas áreas, donde la dificultad de trabajar con otros métodos se presentaba en los pilares, dejándolos abandonados. Es por ello, que la aplicación de este último método es útil en la recuperación de pilares como en el minado propiamente dicho. Asimismo se describe el proceso que comprende: la preparación de la chimenea y subnivel de extraccíón del primer piso, el relleno y finalmente la secuencia de explotación. "

Nov 20, 1972

By R. Pelton, Z. Dai, S. Yang

ABSTRACT Hydrophobic polystyrene nanoparticles were evaluated as potential flotation collectors for pentlandite. The flotation of hydrophilic glass beads demonstrated the nanoparticles’ ability to induce flotation. Deposition of nanoparticles on glass surfaces increased the contact angle and enhanced adhesion of the beads to air bubbles. High flotation recoveries were achieved when 5–10% of the bead surfaces were covered with nanoparticles. Surface functionalization—the addition of vinylimidazole to polystyrene nanoparticle surfaces—caused the nanoparticles to selectively deposit onto pentlandite surfaces in the presence of Mg-Si slimes. Ongoing work includes attempts to identify specific applications where nanoparticle collectors might be cost effective. _ KEYWORDS Flotation, Nanoparticle collector, Coverage

Jan 1, 2014

By J. O. Claassen

"Homogeneous populations are required to perform descriptive, probabilistic, and inference statistics and to support stable, predictable mining operations. The geological and downstream processing environments are, however, highly heterogeneous. The complex nature of mining environments requires means to identify and define multipopulation environments that could affect the performance of mining value chains. A study performed at several operating mines suggests that the impact of heterogeneous or variable geological, mining, and plant processing environments on overall mining value chain performance may not be a key focus area at these operations. This was illustrated through the use of basic and spatial statistics, which included the log-probability plot, a modified range equation, and chronovariography. The findings reflect high relative variability in the geological and processing environments studied and mining operators’ inability to effectively deal with the sources and consequences of variability. The study suggests that a focus on heterogeneity in complex mining operations may significantly enhance overall mining performance. IntroductionHeterogeneity and why it mattersHeterogeneity refers to a state or quality of being variable/diverse and comprising different non-compatible elements or parts. In statistical terms a heterogeneous population can refer to a population comprising different non-compatible sub-populations or a multipopulation environment. The latter is commonly found in natural environments such as geological environments (Bardossy and Fodor, 2001). The inherent heterogeneity of complex geological environments is also referred to as spatial heterogeneity. Heterogeneity or variability, however, also occurs over time at mining operations. A case in point is variable ore composition on a conveyance system feeding a processing plant or product stockpile.Heterogeneity associated with the mining environment can significantly influence key aspects of day-to-day mining operations such as sampling, the use of descriptive, probabilistic, and inference calculations, and an operation’s ability to manage and control the mining value chain as a whole."

Jan 1, 2016

By A. Noble

"Froth flotation circuits are widely used throughout the mineral processing industry for the concentration of fine particles. It had been estimated that nearly 2 Gt (2.2 billion st) of ores are treated globally each year using this versatile separation process (Fuerstenau, 1999). Due to the high feed tonnage, a large economic incentive exists for flotation plant operators to optimize the performance of this critical processing circuit. Prior to the 1950s, the optimization of flotation circuits primarily involved the manual adjustment of operating variables based on visual observation and sporadic sampling (Lynch, Harbort and Nelson, 2010). During the next several decades, however, the advent of improved on-line instrumentation coupled with the rapid development of high-speed microprocessors allowed the industry to develop more advanced control systems that could quickly adjust operational parameters in response to disturbances in ore characteristics and plant flows. These early online controls typically involved feedback loops designed to stabilize cell performance through the automatic manipulation of process variables such as pulp levels, gas rates and chemical dosages. The set-points for these controllers were often set by plant operators based on one or more operator objectives, such as maximizing throughput, recovery or grade. More recently, these regulatory controllers have been interfaced with high-level data display and management systems that provide operators with the ability to better optimize flotation plant performance based on mathematical models and rule-based algorithms (Greet, 2010).While tremendous strides have been made during the past several decades, even the most modern flotation plants are still faced with the long-standing question: “What are we trying to optimize?” From an operator perspective, some common responses include “Maximize tonnage of saleable concentrate” or “Maximize metals recovery at a customer-specified market grade.” These replies may or may not reflect those of management, who often focus on economic goals such as “Maximize profits for each operational unit” or “Maximize rate of return for all corporate assets.” Unfortunately, these high-level objective statements do not always translate well into practice due to the disconnect between plant operating protocols and product value. Attempts have been made by industry to overcome this issue using various types of optimization routines such as linear programming or other optimization engines. While this approach does have some merit, these blind routines require considerable input data and interpretational expertise and provide little or no fundamental insight that can be used to drive improvements in concentrator performance."

Feb 1, 2017

By G. L. Ploetz

The lanthanon compounds are becoming increasingly more important for ceramic and allied applications. As the supply increases and the cost decreases, further development of these interesting materials will undoubtedly lead to new applications and an increased demand. Recent improvements in separation processes have lead to high purity in the individual lanthanon oxides. This report includes short discussions on the mineralogy of the ores as raw materials, and on the separation processes required to produce the pure individual lanthanon oxides in useful quantities. To discuss the presently known applications of lanthanon oxides, this general review is divided into the following categories: A. Glasses, Glazes, and Porcelain Enamels. B. Refractories and Abrasives. C. Electronic Ceramics. D. Nuclear Ceramics.

Jan 1, 1960

By Osvaldo Aduvire

El presente texto describe las mejores técnicas preventiva que permitan predecir la generación ácida permitan a partir de ensayos de laboratorio denominados ensayos ácido/ base que simulan las reacciones que experimentarán los materiales excavados cuando entran en contacto con la atmósfera y agua de lluvia e inicien un complejo mecanismo de oxidación que termine generando drenajes ácidos.

Aug 1, 2012