Search Documents

By I. Iwasaki

In recent years the rapid depletion of high-grade iron ores and the demand by blast furnace operators for increasingly low-silica ores have stimulated interest in flotation studies of low-grade iron ores, such as wash-ore tailings and oxidized taconites. Four processes have been reported for the flotation separation of these iron ores--anionic and cationic collection of the iron oxides, cationic collection of siliceous gangue, and anionic collection of activated siliceous gangue (5).5/ The effectiveness of any one method, however, depends largely on the mineralogical composition and on the physical structure of the sample; hence, a comprehensive study of the floatability of the individual minerals occurring in these materials is essential. A review of the literature shows that the floatability of hematite and magnetite has been frequently investigated, whereas very little corresponding information is available for goethite, or for its more earthy form, limonite, both of which are abundant in the Mesabi and Cuyuna ores (19). The purpose of this investigation was to formulate general information on the floatability of goethite. Vacuum flotation, contact angle measurement, and simplified flotation tests using a modified Hallimond tube were used. The experimental results were correlated with the electrokinetic properties of goethite as determined by streaming potential measurement. The results were used to interpret the batch flotation tests made on an artificial mixture of quartz and goethite.

Jan 1, 1960

By John Berney-Ficklin

Large scale grinding mills can reduce both capital and operating costs for concentrators. These mills can be effectively used, but they must be free from design and manufacturing deficiencies if they are to reach their full potential and avoid costly downtime. This paper presents the evolution of today's complex grinding mill specifications and discusses the most important items to look for when buying new equipment. It emphasizes the need to monitor specification requirements during design and manufacture. It also discusses the growing trend to have grinding mills fabricated in overseas plants, and the importance of recognizing this when preparing specifications.

Jan 1, 1987

By M. E. Grimes

A method of predicting uranium extraction rate in underground bacterial leaching of as-blasted ore has been developed. The method is based on the hypothesis that extraction is directly proportional to the volume of a piece of ore that is penetrated by the leaching agent, and that each piece of ore, regardless of size, has been penetrated radially from the external surface to the same depth at a given leaching time. Consequently, given an initial size and assay distribution, extraction should be predictable for a given penetration. Two laboratory bacterial leaching tests under simulated stope leaching conditions were carried out for a periods of 89 and 96 weeks. On completion, the residual ore was screened and analyzed. The information so obtained was employed to provide an elapsed time base for the penetration model, from which predictions of future extraction were made. The finding of solubilized uranium trapped within apparently sol id ore pieces was unexpected. However, it is not recoverable except after crushing, and hence does not affect calculations of underground leaching .

Jan 1, 1974

By R. J. Matetic

The objective of this U.S. Bureau of Mines hydrologic-subsidence investigation was to evaluate the effects of longwall mining on the local ground water regime through field monitoring and numerical modeling. Field data were obtained from multiple-position borehole extensometers (MPBX's) that were used to measure subsurface displacements. Survey monuments were installed to measure mining-induced surface deformations. Numerous drawdown and recovery tests were performed to characterize hydrologic properties of the overburden strata. Coreholes were drilled above the study area to determine lithologic and strength characteristics of the overburden strata using the rock samples collected. Electronic recorders were installed on all monitoring wells to continuously monitor ground water levels in coordination with mining of the longwall panels. A combined finite element model of the deformation of overlying strata, and it's influence on ground water flow was used to define the change in local and regional water budgets. The predicted effects of the postmining ground water system determined by the model correlated well with field data collected from the fieldsite. Without an infiltration rate added to the model, a static decrease of 3.0 m (10 ft) in water level would occur due to mining of both longwall panels and if an infiltration rate was inputted in the model, no predicted long-term effects would occur to the ground water system.

Jan 1, 2010

By Stephen C. Tadolini, Anthony T. Iannacchione

"Coal burst represented a major hazard for some U.S. mining operations. This paper provides an historical review of the coal burst hazards, identifies the fundamental geological factors associated with these events, and discusses mechanisms that can be used to avoid their occurrences. Coal burst are not common in most underground mines. Their occurrence almost always has such dramatic consequences to a mining operation that changes in practice are required. Fundamental factors influencing coal burst events include strong strata, abnormal strata caving, elevated stresses, critical size pillars and the lack of sufficiently sized barrier pillars during extraction. These factors interact to produce excessive stress, seismic shock and loss of confinement mechanisms. Over the 90 years of dealing with these hazards, many novel prevention controls have been developed including novel mine designs and extraction sequences, most of which are site specific in their application. Without an accurate assessment of the fundamental factors that influence coal burst and knowledge of their mechanisms of occurrence, control techniques may be misapplied and risk inadequately mitigated. INTRODUCTIONCoal burst1are violent failures of ribs, roof or floor in underground mines. They are known to occur in complex ways and often under unique sets of conditions. This has made them extremely difficult to anticipate and control. Assessing coal burst risk requires engineers, managers, and safety professionals to recognize the fundamental factors responsible for these events. This helps practitioners recognize the hazard potential and understand the context in which various controls and barriers should be used. Only then can coal burst events be anticipated andappropriate mitigation techniques deployed.Over the last 90 years, a few coal burst events have been anticipated but most have eluded prediction. The authors examined the historical record (Appendix A) and determined that an inadequate understanding of the initiating geologic factors and their associated mechanisms of occurrence have contributed to the poor predictive capability. The historic record also indicates that control techniques have typically been site specific in their application."

Jan 1, 2015

By L. L. Rethi

The U.S. Bureau of Mines summarized injury data for independent contractor employees working at all locations of coal and metal-nonmetal mines from 1983 through 1990. During the eight years, the greatest contrast in degree of injury between independent contractor and operator employees was in fatalities. From 1983 through 1990, there were 132 independent contractor employee fatalities in the mining industry. In 1988 though, independent contractor employees accounted for nearly one-fourth of all mining fatalities. The fatality incidence rates of independent contractors were consistently higher than those of operators during the eight years. For instance, in 1990, the contractors' rate was twice that of operator employees in coalmining and nearly five times that of operators in metal-nonmetal mining. Three other salient facts highlight the independent contractor employees' fatality injury data during these years. First, 82% of the independent contractor employee fatalities occurred at surface locations. Second, two job classifications?truck driver and equipment operator?represented 37% of the fatalities throughout the 8-year period. And finally, four accident classifications?powered haulage, slips and falls, machinery, and electrical?accounted for 71% of all independent contractor employee fatalities.

Jan 1, 1993

By John S. Brock

During 1964 and 1965 a mineral exploration program was carried out over an area of approximately 250 square miles, located in the Anvil-Vangorda Creek area of east central Yukon, 125 miles northwest of Whitehorse. The Vangorda deposit, a massive lead-zinc sulphide body discovered in 1953, was centred in the area proposed for exploration, a northwest trending belt located between the southwestern flank of the Anvil Range and Pelly River. Exploration for base metals in the remote Anvil area had previously been restricted by poor metal markets in the late 1950's. Regional geologic information was also limited except for publication of a scale 1 inch to 4 mile map by the Geological Survey of Canada in 1961. To effectively explore this area, a combination of geophysical and geochemical methods were essential due to extensive overburden cover varying in depth from a few feet to over 300 feet. (Figure (i) Key Map) Dynasty Explorations initiated the first comprehensive regional exploration program in the Anvil area, utilizing saturation prospecting methods employing geologic, geochemical and geophysical methods. The program involved an approach demanding continual modification of technical and physical logistics. After a total of 12 months of field work involving an expenditure of approximately $450,00, massive sulphides were discovered which subsequently proved to be an economic orebody. Thirteen properties had been acquired and explored. Ten separate geophysical anomalies had been outlined by a combination of magnetic, electric and gravimetric survey techniques of which five were tested by rotary drilling and two by diamond core drilling. The discovery of the Faro deposit was a direct result of this program.

Jan 1, 1971

By John E. Pahlman

The U.S. Bureau of Mines has continued its investigation of chemical additive drilling fluids that produce a zero surface charge (ZSC) on a rock to better define the boundary conditions of the phenomenon. Laboratory drilling tests were performed on Minnesota taconite, Tennessee marble, and Sioux Quartzite using diamond-impregnated coring bits or tungsten carbide spade bits. Drilling fluids were made from chemical additives such as inorganic salts, cationic surfactants, cationic polymers, acids, or nonionic polymers in either distilled, deionized water (DDIW), mine pond water, mine well water, or tap water. These additives were tested below, at, and above their respective ZSC concentrations. Penetration and bit life improvements obtained with ZSC concentration solutions ranged from 88 and 56 pct, respectively, to over 650 pct and over 400 pct, respectively, for the additives tested. Polyethylene oxide (PEO) was found to be the best additive for ZSC-controlled drilling because a continuous range of PEO solution concentrations produced the enhanced ZSC-controlled drilling performance.

Jan 1, 1989

By J. K. Whyatt

Researchers at the U.S. Bureau of Mines collected and analyzed overcore measurements and other indicators of in situ stress characteristics at the Lucky Friday Mine, Mullan, ID. An analysis of these data revealed that significant local variations in in situ stress are present in this mine and that these variations existed prior to mining. High stresses were found to be associated with the most competent strata and a locked section of a fault. An estimate of the predominant stress field was developed for mine-wide modeling. The estimate shows that the greatest principal stress was oriented north of northwest. This information should provide a basis for mine-wide structural modeling of the Lucky Friday Mine and should generate important insights into localized stress conditions, which may significantly affect both local and mine-to-mine variations in seismicity induced by excavation.

Jan 1, 2010

By John E. Pahlman

The Bureau of Mines conducted column-leaching tests on 25 domestic Mn ores to determine the feasibility of extracting Mn by in situ or heap leaching with dissolved sulfur dioxide (S02) solutions. The ores tested were obtained from deposits in Arizona, Arkansas, California, Colorado. Maine, Minnesota, Nevada, and South Dakota. Dissolved S02 was found to be effective for leaching Mn; extractions greater than 90 pct were obtained with solution application rates of 1 mL/min from uncalcined, minus 2.5-plus 1.3-cm ore pieces. Leaching these ores with solutions containing only 5-wt-pct S02 and no added H2S04 resulted in Mn being selectively extracted over Fe except when Fe was present as goethite or siderite. Ca solubilization was inhibited by controlling the solution application rate (1 mL/min). The rate of leaching was found to be principally dependent upon the rate at which the leaching solution can penetrate the ore, since the solubilization of Mn upon contact with S02 was observed to be rapid. Despite low water permeabilities of the ores (as low as 10-2 to 10-4 darcy). greater than 90 pct of the Mn was extracted from even the largest ore pieces tested (approximately 10 cm in diameter). It appears, therefore. that leaching Mn opens up the pores, allowing penetration of the leach solution into the ore pieces.

Jan 1, 1988

By E. V. Deshayes, W. E. Young

"INTRODUCTION The Camp Bird mine was investigated by Bureau of Mines engineers 3/ September 22 and 24, 1942, and April 29 and 30, 1944. In a subsequent report and supplement, it was recommended that core drilling be done below the 14th. level to determine if commercial ore existed at greater depths, and particularly if ore existed in the vein or adjacent thereto where it passes into the sedimentary formations estimated to underlie the volcanics approximately 400 feet below the 14th level.Seven diamond-drill holes aggregating 3,956 feet were drilled. Four of these holes were under the Hematite ore body and three were under the Big Discovery ore body. Two holes under, the Hematite ore body wore directed at angles but little steeper than the angle of dip of the vein and penetrated the sedimentaries beneath the volcanics close to the vein. Enough low-grade ore was found at the base of the Telluride conglomerate to indicate the presence of a large body of low-grade zinc sulfide ore. Two holes were directed to crosscut the vein at a depth of approximately 125 feet below the 14th level. No commercial ore was cut, but the vein showed the average width and same general characteristics as at the 14th level. One hole under the Big Discovery ore body was directed to crosscut the vein and test the base of the Telluride conglomerate in the footwall block. No commercial ore was found in either the vein or the sedimentary horizon. One hole was directed to test the base of the Telluride conglomerate in close proximity to the vein in the hanging-wall block. This hole was lost approximately 100 feet short of its objective, and a third hole was drilled to accomplish this same thing. The third hole was stopped approximately 50 feet short of its objective when failure of equipment caused a recess of the"

May 1, 1948

By E. P. Hayes

This report supplements the date contained in Bureau of Mines Information Circular 6156, "Special features of core drilling in the salt beds of Western Texas and New Mexico," by J. S. Wroth. That circular dealt with the drilling of the first 12 of the 24 potash tests made by the U. S. Bureau of Mines in cooperation with the U. S. Geological Survey; this report is concerned with the drilling of the last 12 tests. ACKNOWLEDGMENTS The writer is indebted to R. E. Heithecker, the Bureau of Mines engineer who had charge of the drilling of tests 13 to 17, for his well-prepared records on the drilling of these tests.

Jan 1, 1933

By Don Steffa

Drift mining, according to California mining terminology - and it is distinctly a California development - is the blocking out and extraction (breasting) of the auriferous gravels of an ancient buried stream either through tunnels, inclines, or shafts; it is one of the minor divisions of the larger classification known as placer mining. The contribution of each of these divisions and of lode mining to the gross production of gold in California totals as follows:3 [ ] The total amount of gold recovered from the placers of California from 1848, when Marshall discovered the precious metal in the mill race at Coloma, to 1928, was $1,226,515,404. The same period saw a total gold production from all operations of $1,823,562,360.

Jan 1, 1932

By S. Castro

The aim of the present paper is to review the current technologies for arsenic removal in the copper metallurgical industry, and to show the progress made with some promising emerging strategies, involving the pre-treatment of copper-arsenic concentrates by selective flotation or by alkaline leaching with Na2S-NaOH solutions. The advantages of alkaline leaching are the selective dissolution of arsenic and antimony, the high extraction yield, and the practically nil loss of copper, which remains in the clean copper concentrate as a CuS residue. Alkaline ?cured? ? a procedure similar to ?acid-cured? in conventional leaching ? improves arsenic extraction and reagent consumption, making this an interesting technology for the treatment of high As-Sb concentrates. In light of recent advances on the selective flotation of enargite and tennantite, the importance of redox conditions to control the flotation/depression of enargite-tennantite from copper sulfides has been well established. However, problems of selectivity must still be solved. Additionally, the limitation imposed in some cases by the need to recover the molybdenum by-product must be considered. The application of selective flotation to obtain a high-arsenic or ?dirty? concentrate and its sub-sequent treatment by the alkaline leaching process is suggested.

Jan 1, 2014

By John Marsden

Despite the recent pullback in metal and mineral prices, and the associated market adjustments, the mining industry is still facing a serious issue with the declining availability of graduate expertise. This is due to a combination of an aging workforce, retirements and retrenchments, coupled with a lack of suitably qualified graduates entering the workforce. The issue has certainly improved since 2004 when the industry picked up the rates of hiring graduate engineers and mining/mineral school enrollments picked up in response. This hiring effort has helped to cover the ?gap? years from about 1985-2000, when industry demand for graduates was particularly poor. However, the recent market pullback is likely to set back this progress, as recruitment and hiring wavers as a result of cost cutting measures and economic uncertainty. A key issue for the mining industry is how to ensure the survival and growth of relevant ?core? degree programs. Such programs include mining, metallurgical, mineral processing and geological engineering. The mining industry needs a healthy, high-level education program to ensure an adequate supply of appropriately qualified graduates for the mining industry. Two-thirds of the professionals entering the minerals industry who graduated within the past 40 years graduated prior to 1985. Since 1985, we have been living off the legacy of graduation classes from the mid-1970s and early 1980s. It is estimated that we have been producing graduates at approximately 40 to 50 percent of the sustaining rate since about 1985. Further growth in the domestic industry would increase graduate requirements significantly, and the export of U.S.-graduates to other parts of the world (as is currently occurring) also impacts the total graduate requirements.

By Ralph J. Holmes

"An accurate knowledge of the chemical, mineralogical and physical characteristics of ores and mineral products that are mined, processed and sold commercially is crucial to resource definition, effective resource utilisation, plant design, process control, metallurgical accounting and finally quality control to ensure that contract specifications are met and equitable payment is received for product sales. However, the responsibility for sampling is often entrusted to personnel who do not fully appreciate the significance and importance of collecting fully representative samples for analysis, and they seem satisfied as long as some material is collected and returned to the laboratory for analysis. Furthermore, sample stations incorporated into the design of new plants are often the first casualties when cost cutting exercises commence. There is really little point in accurately analysing samples if they are not representative in the first place, because the resultant analyses can be seriously biased and the effort taken to carefully analyse such samples is largely a waste of time and resources.Ultimately, a poor knowledge of the characteristics of ores and mineral products limits the ability of mining companies to optimise the life of ore resources and plant performance, and failure to meet final product specifications can have disastrous consequences, including price penalties and more seriously loss of sales contracts and significant revenue losses due to poor sampling practices at the point of sale. Consequently, it is critical that sampling is given the attention it deserves as the first important step in the quality measurement chain. The golden rule for correct sampling is that all parts of the ore, concentrate, slurry or other material being sampled must have an equal opportunity of being collected and becoming part of the final sample for analysis."

Jan 1, 2016

By G. A. Savanick

The Bureau of Mines has designed, fabricated, and field tested a water jet cutting device capable of perforating nonmetallic well casings for the purpose of completing or stimulating in situ uranium leaching wells. The device is lowered into the wellbore, where it issues a high-velocity water jet that penetrates either a polyvinyl chloride or fiberglass casing, cement, and from 1 to 4 feet into the surrounding uraniferous sandstone. The resulting perforations allow leaching solution to pass between the sandstone and the wellbore. This report describes the water jet perforator, tells how it is used, presents cost data, and discusses the results of laboratory and field tests. The tests were designed to (1) determine the optimum operating conditions for water jet perforation, (2) assess the effects of changes in these conditions, (3) evaluate the performance of the water jet perforator under actual conditions, and (4) compare this method with other methods of well completion. These tests showed that water jet perforation is superior to conventional well completion methods for selectively achieving communication between the well-bore and adjacent sand while maintaining sand control, for restoring permeability lost through wellbore damage, for stimulating poorly performing wells for completing wells with casings that have inside diameters as small as 2 inches, and for extending the effective well diameter.

Jan 1, 1981

ONE of the morning sessions at the recent Annual Meeting was devoted to a Symposium on ways and means to expedite geological investigation, and also to promote greater prospecting activity, in Canada. It will be recalled that at the 1940 Annual Meeting, held in Winnipeg, a paper(l) prepared by Dr. G. A. Young, Chief Geologist of the Geological Survey, was presented, and was followed by a Symposium on Geological Investigations in Canada(2). On that occasion, the participants were in the main geologists, and they included the directors or other officials of each of the Provincial departments or bureaus of mines. At the Montreal meeting, the subject was discussed mainly from the point of view of the mining industry. The following pages present, in somewhat summarized form, the several contributions to that discussion.-ED. DR. J. J. O'NEILL(3), who was to have opened the Symposium, was unfortunately prevented through illness from attending the meeting. He had intended outlining the main features of his paper on The Exploitation and Conservation of Mineral Resources in a Balanced Development of Canada, presented at the last annual meeting of the Royal Society of Canada( 4). In his absence, DR.J. A. DRESSER presented a summary of the paper.

Jan 1, 1941

The Mateen deposit comprises two large spodumene-bearing pegmatite dikes that outcrop along the, side and crest of a hill overlooking 'Rill City in the southern Black Hills of South Dakota. The Bureau of Mines investigated the Mateen deposit as part of a comprehensive study of the lithium mineral-production possibilities in the Black Hills area. The work was undertaken during the second World War, when the demand for certain lithium salts and compounds exceeded the small productive capacity of the industry. During the course of the investigation, the Bureau of Mines took 61 large channel samples from surface trenches, 4 channel samples from a shaft, and 3 from the face of an open cut. In addition, 8 diamond core-drill holes were completed to investigate the attitude of one of the dikes at depth. Metallurgical tests were conducted by the Bureau of Mines to determine the feasibility of beneficiating spodumene-bearing ores from the Mateen dikes.

Jan 1, 1948

By H. P. Greenwald

About mid-December 1936, the safety director of a large coal corporation visited the authors at the Bureau's Experimental coal mine to discuss a rock-dust barrier he had invented primarily for use in trackless entries of coal mines. The rock dust in this device was carried in its original paper containers and means were provided for ripping these open so that the dust might be scattered in the path of an explosion. The inventor termed the device a "bag barrier", and this term has been adopted in the present paper for convenience. At that time the device was in an early stage of development, and the inventor felt that the barrier should be tested to determine whether it had enough promise of being successful to justify further development. The matter was taken under consideration and finally three tests were made during the week of February 15, 1937. It was concluded that while the device did stop an explosion in two of the three tests, it was much loss effective than ordinary rock dusting, and that too few data were obtained to permit direct comparison with tests of other barriers. Apparently, the conditions under which the device could, be successful 'Were somewhat limited, out the limits could not be defined without additional tests.

Jan 1, 1938