Search Documents

By J. B. Gayle

The removal of coal particles from a slurry by flotation is made possible by the formation of stable aggregates with air bubbles of suitable sizes. The formation of such aggregates is theoretically possible only for certain favorable combinations of the solid-liquid-gas interfacial tensions. Because interfacial tensions involving solid phases are not conveniently measurable, a related variable, the contact angle, frequently is used as a measure of the floatability of various materials. Zero angles indicate nonfloatable substances, and large angles indicate substances having a high degree of floatability. During a study of contact angles for coal and substances related to coal in their similarity of response to various physical and chemical treatments, particularly flotation, carbonization, and oxidation, the reproducibility of replicate determinations taken within a 4-hour period was found to be much better than that for comparable results taken over a longer period of time. Consideration of possible causes for these differences led to an investigation of the effects of temperature variations on contact angles. References to literature revealed only a small amount of information, some of it apparently conflicting. Specifically, Sutherland and Wark4/ found that temperature variations "within limits" did not appreciably influence the angles measured for galena conditioned with potassium ethyl xanthate. On the other hand, McGlashan and McLeod5/ presented preliminary data showing that for sphalerite conditioned with potassium ethyl xanthate the angle is maximum at 25° to 35° C., depending on the pH of the system.

Jan 1, 1960

For the convenience of those who are unfamilar with thermodynamics, the following brief description and explanation is given of the thermodynamical terms and methods used in this book. It must, however, be strongly emphasized that the account given below is not an introduction to chemical thermodynamics; its sole purpose is to give the reader a rough understanding of the methods used in the earlier chapters. For further information, reference must be made to the standard textbooks on chemical thermodynamics by Glasstone.

Jan 1, 1953

By B. B. Letson, D. F. Smith, T. E. Gardner, A. R. Taylor

Low- temperature heat capacities of strontium chloride (7° - 300° K) and strontium fluoride ( 11 ° - 300 ° K) were measured with an adiabatic calorimeter . Smooth values of heat capacity , entropy , enthalpy function , and free - energy function were calculated from the heat - capacity data . The smooth values are reported at 10 ° K intervals and at 273.15 ° and 298.15 ° K.

Jan 1, 1963

By Victor V. Verbinski

This report presents the development of a raw coal concentration sensor for hydro-transport of coal and refuse (rock) from underground mines, and the results of an international test series carried out at the Colorado School of Mines Research Institute in Golden, Colorado, the U.S. Bureau of Mines, Hydraulic Transport Research Facility in Pittsburgh, Pennsylvania, Saskatchewan Research Facility in Saskatoon, Saskatchewan, Canada, and the Steinkohlenbergbauverein Test Facility in Essen, West Germany. Test results are presented for a three-component sensor and also for the more rugged two-component (all nuclear) sensor.

Jan 1, 1988

By Shengli Wu, Jiacong Zhang, Kai Gu, Bingjie Wen, Heng Zhou

In practical production process, the average of silicon content in hot metal (HM) of COREX process (the average is 1.58%) is obviously higher than that in blast furnace (the value is below 0.6%), which leads to an increase in the cost of steelmaking. In this work, the factors affecting and impact mechanism of silicon content in HM were investigated by statistical analysis using actual operating data. The analysis indicates that the fuel rate, binary basicity of slag and the temperature of HM are positively correlated with the silicon content, while the sulfur content of HM and binary basicity of burden are negatively correlated with the silicon content. On this basis, a back propagation neural network was developed to predict and control the silicon content in HM. All the findings of this work are useful for guiding and optimizing the COREX operation.

Mar 1, 2018

By L. R. Woodyatt, H. J. Beattie, C. T. Sims

Theories correlating the formation of u and related intermetallic compounds to the electron-per-atom density of binary and ternary alloys have appeared regularly in recent technical literature. These same principles can be modified and applied to complex precipitation-strengthened alloys such as the iron-, cobalt-, and nickel-base superalloys and the stainless steels. Since these complex alloys contain carbides and other phases that normally precipitate before the U-type phases, the nature and amount of the precipitated phases must be calculated first. The following general formula is then applied to the residual matrix composition of the alloy: element. The magnitude of the resulting number is indicative of whether the alloy will form a a -type phase. When these calculations (which are computerized) are systematically applied to alloys of knoun phase analysis, a breakoff in average electron-vacancy number is noted between U-free and U-prone alloys. Alloys with an average electron-vacancy number higher than the breakoff form a-type phases, while those with lower ones do not form these phases. This method could then be used to eliminate from consideration all experimental compositions that would precipitate undesirable phases. It also is useful in evaluating analyzed heats of alloys where minor heat-to-heat variations determine whether the alloy is o-free or o-prone. THE highly significant development of strong, ductile superalloys to provide reliable construction materials in the 1000" to 2500° F temperature range has been due principally to unremitting application of Edisonian techniques and logic by the dedicated physical metallurgists who have shouldered this responsibility. Tools such as the electron microscope, phase analysis, and computers to accomplish regression analyses have been used heavily, but the effort has been essentially practice of an art, rather than a science. The objective of this paper is to describe and illustrate application of some relatively fundamental principles to certain of these alloy systems in an attempt to remove some of the empiricism from the technology. Specifically, the work presented here deals with the use of periodic-group relationships to predict the formation of intermetallic phases which can occur in primarily austenitic (fcc) structures. Calculations that have been developed might be applied in the design of new alloys and the evaluation of known alloys, and thus have the potential of eliminating vast areas of unnecessary alloy preparation and evaluation. ALLOYING CONCEPTS AND STRUCTURAL FEATURES OF SUPERALLOYS Strength is produced in austenitic superalloys by three principle mechanisms: 1) precipitation of y'; 2) formation of carbides; 3) solid-solution hardening by soluble refractory metals. The first mechanism requires the addition of aluminum and titanium, the second requires carbon and carbide-forming elements, while the third calls for the addition of molybdenum and/or tungsten. A considerable concentration of chromium is usually maintained to resist oxidation/corrosion, but it is also an important carbide-forming element. Fig. 1 shows a sketch and electron micrograph of the structure of a typical wrought nickel-base super-

Jan 1, 1967

"An innovative concept is proposed whereby the operating power for haul trucks in certain areas of an underground mine are reduced in order to lower ventilation costs. Airflow that must be provided for diesel-powered equipment in most jurisdictions are regulated based on engine peak power capability and engine emissions, both of which can be lowered by artificially reducing the capacity of the engine through the engine control unit. Advances in asset tracking and ventilation on demand enable this methodology and this study demonstrates that it could represent significant value for mine operators. An examination of haul truck duty cycle indicates that de-rating of engine operating power based on the truck’s location in the mine can enable a step change in ventilation rates, often with no material impact on working conditions. Methods for implementation and estimate of cost savings will be defined.INTRODUCTION Ventilation of underground workings remains a significant operating cost burden for modern mine operators. In particular, ventilation rates for underground diesel mining equipment are often defined by local regulatory bodies and are assumed to present minimal opportunity for optimization or savings, at least until battery propulsion systems can be adopted. Commonly, the quantity of air flow required is defined by the peak rated engine output power of diesel equipment. For example, Ontario Regulation 854 SS 183.1 (3) states that “The flow of air must be at least 0.06 cubic metres per second for each kilowatt of power of the diesel-powered equipment operating in the workplace”. Jurisdictions that define air flow using the prescribed CANMET or MSHA ratings use peak engine emissions to calculate air flow required for dilution ventilation. These approaches are similar in that the maximum power capability of a vehicle’s engine is used to define the ventilation rate in all areas where it travels, regardless of what power output is actually used in any of those areas. Examination of the duty cycle of a typical underground haul truck identifies a large variance in the power output of the vehicle depending on its location in the mine and the activities undertaken at these locations. For example, travel on a mining sub-level requires a fraction of the truck’s peak power due to the minimal grade and significantly reduced travel speed. So if we can reliably reduce the peak engine power capacity and engine emissions in areas where peak power is not required, we can logically cut the ventilation rates for those areas."

Jan 1, 2017

By L. R. Burdick

The Smokescope is an instrument recently developed for determining the density of smoke by shade comparison. The instrument is designed so that the smoke is seen adjacent to two shades of gray corresponding to Nos. 2 and 3 on the Ringelmann chart. Data on smoke density are important in the smoke-abatement field. The method that is specified and accepted as standard for smoke-density determination by the majority of city smoke regulations involves comparing the smoke shade with the four shades on the Ringelmann chart as published by the Bureau of Mines.2/ This investigation was made to determine the accuracy and convenience of the Smokescope. It was conducted as a part of the Bureau I s air-pollution work, which includes the study of techniques that will promote smoke abatement. The accuracy of the Smokescope was arbitrarily defined as the difference between the Smokescope determinations and the determinations by the accepted, standard method and was expressed as Smokescope correction. Although the corrections obtained were strictly correct only for the two observers and the Smokescope of the investigation, they indicate what might be expected from any observer who uses a Smokescope with reference shades that duplicate those of the test instrument. The report is devoted largely to the data on Smokescope correction, which were taken from a single stack under controlled smoke conditions. Field work, which was done at various locations with different stacks, is mentioned briefly in connection with the comparison of the convenience of the two methods. The data for estimating Smokescope correction were taken for the three variables that were expected to affect the results, namely, the density of the smoke, the amount of light, and the color of the sky behind the smoke.

Jan 1, 1955

By Paul M. C. B. M. Cools, Martin Th. van Staveren

In 2010, the 5-years joint industry programme Geo-Impuls started in the Netherlands. The ambitious goal of this programme is to reduce geotechnical failures in our civil engineering projects by half in 2015. In the Geo-Impuls programme over 40 client organizations, engineering firms, contractors, research institutes, and universities are involved. In a risk-driven way, and based on top risks and dilemmas, the participants defined three central development themes. These themes are (1) contracts, for dealing with legal issues, (2) geo-engineering, for dealing with technical issues, and (3) communication, for paying attention to differences in risk perception by the human factor. In total 12 Working Groups contribute to these themes by producing one or more specific tools. These provide practical solutions for how to deal with contractual, geotechnical, and communication issues. The tools include working processes, guidelines, best practices, as well as some instruments. The development of these tools, as well as the available results, will be presented in this paper. From the start, Geo-Impuls embraced geotechnical risk management (GeoRM) as the risk-driven way of working for geotechnical engineering and construction. Over the past years, GeoRM and its supporting tools were already successfully applied in several projects. Therefore, the paper also describes also the GeoRM implementation process, including the quality assurance and control. Finally, the effectiveness of GeoRM will be discussed, by summarizing an analysis of all published geotechnical failures and accidents in construction projects in the Netherlands, which decreased substantially over the past 4 years.

Jan 1, 2017

By Guy A. Johnson

Despite the use of warning alarms to alert miners to the backward movement of large mining equipment, miners still are injured too frequently in backup accidents. Currently approved backup alarm technology consists of continuous sounding alarm systems. New technology has developed a warning system that initiates an alarm only if there is an object close behind the vehicle. This advancement eliminates constant exposure to the alarm because a warning is given only in case of a potential collision. Adoption of this development can improve safety and reduce damage, especially for front-end loaders (FEL's). It will also eliminate a source of nuisance noise in urban and residential areas. This Bureau of Mines report describes the general characteristics of infrared (IR) light, ultrasonic wave, and Doppler radar technology as used for backup alarms, and reviews the testing of the most promising detection devices.

Jan 1, 1986

By F M. Weir, M Fowler

A discrete fracture network (DFN) approach involves numerical modelling that explicitly represents how defects may be spatially distributed through a rock mass. A DFN is a 3D realisation of the ‘smaller scale’, non-deterministic defects; it is not an attempt to model larger, deterministic structures that should be identified as part of an engineering geology model. The approach utilises structural data in stochastic analyses to give a range of possible models that provides a tool for visualisation and analysis of a rock mass and indicates the potential large-scale slope or tunnel performance and stability.Stochastic fracture modelling for rock mass characterisation has significantly advanced over the past 25 years. With recent improvements to field data collection and computational power, it has become recognised internationally as a valuable tool for modelling some geomechanical problems encountered when designing excavations in fractured rock masses.This paper provides an introduction to the DFN approach, particularly the necessary input parameters and derivation of these from typical structural data sources, such as boreholes or scan line mapping. Of particular importance for engineering applications is validation of the simulated fracture network and techniques for doing so are discussed here.CITATION:Weir, F M and Fowler, M, 2014. An introduction to discrete fracture network modelling and its geotechnical applications, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 435–444 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By M. G. Hester

The inadequacy of traditional geostatistical methods for estimating some precious metals deposits has become apparent in the last few years. New methods or estimation such as Indicator, Probability and Multigaussian Kriging are difficult to understand and apply. Case studies using a new method of variogram calculation proposed by Srivastava show the method valuable for variogram estimation in precious metal deposits. Some simple, sometimes unorthodox. estimation methods that have proved useful in Some situations are presented.

Jan 1, 1990

By Suthan Pooranampillai

Verification of drilled shaft resistance is primarily obtained through the use of different load testing methods. Procedures utilized include conventional top down static loading, the Osterberg load cell (O-cell) test and dynamic tests such as the Statnamic method. The O-cell test provides a means of obtaining separately the base and side shear resistance behavior of drilled shafts (cast-in-drilled-hole). Alternatively, the Statnamic load test method enables the engineer to derive base and side shear behavior separately, based on measurements of load, accelerations and strains along the length of the shaft. However, due to time and cost constraints these tests can only be performed on selected shafts within a project. Post grouting of a drilled shaft base embedded within a cohesionless material, with a low mobility compaction grout, will essentially pre-load the shaft base soil against the side shear and self-weight in much the same manner as an O-cell load test (when the load cell is placed within the base vicinity). Therefore, successful post grouting of a drilled shaft would enable verification of both shaft side shear and base resistance simultaneously on each and every shaft it is carried out on. Additionally, such post grouted shafts display stiffer load-displacement response during subsequent downward, superstructure induced, loading compared to ungrouted shafts. Verification of resistance on each and every shaft through the use of post grouting will allow an increase in resistance factors (reduction in safety factor) used in the design. Two 6 ft. diameter drilled shafts were constructed in Fredonia, WA, for WSDOT, each with an approximate length of 52 ft. The shafts were terminated within medium dense poorly graded silty sand. Statnamic load testing of the shafts indicated maximum derived static side shear and base resistances of 2545 kips and 507 kips (1.6 in. displacement) for shaft One and 2466 kips and 212 kips (1.4 in. displacement) for shaft Two. Shaft Two was subsequently grouted, with a low mobility compaction grout. Shaft base mounted total earth pressure cells measured a maximum sustained pressure of 55.44 ksf during the compaction grouting operation. Shaft displacement reached 0.65 inches in the upward direction at termination of grouting. Comparison of grouting data with initial load test information indicates that properly instrumented post grouting verifies shaft base and side shear resistance. In addition, these grouting induced resistances were much higher than design values supplied by the engineer using conventional resistance factor design. Large scale laboratory testing also shows that base grouting verifies higher soil resistances than permissible in conventional design.

Jan 1, 2010

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

This paper describes the general principles of the expander body with post-grouting (EBI) system, and how it is similar in nature to a large-scale pressuremeter device. The results from the installation of an EBI can be used to provide information about the stress-strain characteristics of the soil adjacent to the device and to compute estimates of nominal axial resistance. As the EBI expands during grouting, pressure is applied to the in-situ soil surrounding the device thereby compacting/densifying the soil. The nominal axial resistance for small diameter piles/ground anchors can be increased due to the greater soil stiffness and shear strength around the device, larger surface and end area, and improved soil-to-EBI interaction in side resistance. The shape of the response curves depends on the geotechnical conditions of the soil (e.g., in-situ stress state, strength, and stiffness) and the installation method of the piling/ground anchor. This technique has been used successfully with different pile types and ground anchors in a wide range of conditions from very loose sands/silts to very dense sands and medium-dense gravels as well as in soft to stiff clays. This paper also describes a mini case history in which 80 piles were installed to support an office building, and the results of the static axial compression load tests performed on a production FDP+EBI pile is also included.

By H. Al-Kazzaz

The effects of laser power and joint gap on the welding quality of 2-mm butt joints of ZE41A-T5 sand castings were investigated using a continuous wave 4 kW Nd:YAG laser system and 1.6-mm EZ33A-T5 filler wire at a welding speed of 6 m/min and surface defocusing. The smooth weld profiles with the minor welding defects were obtained at a laser power of 4 kW and joint gap of 0.3-0.4 mm. The hardness values in the fusion zone are similar to those of the base metal but there is a drop in the heat-affected zone after a natural aging of 18 months.

Jan 1, 2006

By L. M. Lowe, D. B. Chambers, D. G. Feasby

"Potentially economic deposits of rare earth elements (REE) often contain elevated levels of naturally occurring radioactive materials (NORM), primarily thorium and uranium and their associated radioactive decay products. The concentrations of NORM usually exceed typical background levels of natural radioactivity, sometimes by factors of ten or more, and can be of concern relative to occupational radiation protection and the management and disposal of REE mineral processing and metallurgical wastes. This paper provides a summary of the radiological issues normally encountered in the REE concentrate production industry. In addition to an introduction to background radiation and radioactivity, including the thorium and uranium radioactive decay series, radiation levels expected to be encountered in REE concentrate production are outlined. The occupational, environmental and regulatory aspects of REE production related to NORM, including radiation dose limits, radioactive waste disposal guidelines, and threshold VALUES (for the application of transport regulations, are presented.INTRODUCTIONConcurrent with the increasing demand for new sources of rare earth elements (REE) to meet modern industrial needs, there is also an increasing awareness of the radioactivity associated with the REE ores and resources. This is an especially important consideration in addressing questions from the public and local communities who are often concerned about “radiation” and “radioactivity”. Public concern is heightened by reference to legacy issues that arose during times of less regulatory oversight; as well, the benefits of modern technologies, practices and regulation are overlooked. Such concerns are also often inflamed by unfounded claims by non-governmental organizations (NGO’s). Thus, it is important that all concerned have a full understanding of just what the potential risks from radiation associated with REE are, or are not. This paper provides an overview of the sources of radioactivity, the potential implications of radiation and radioactivity in the REE industry, and a brief discussion of established and reliable methods of managing exposure to radiation and radioactivity."

Jan 1, 2012

Over the last ten years geological and mining software products have evolved greatly. Software companies developing such products have focussed almost exclusively on the development of technical aspects of the applications, addressing geological, ore reserve estimation and mine planning problems. These specialist applications, and the many other new technologies that are being developed by a myriad of niche developers, are an essential part of todayÆs hi-tech mining operations. Technology is also being used in many other areas to improve the mining process and there is no doubt that tremendous advances are being made in all these fields. Yet there is something missing. The manner in which the technologies are used and implemented has led to the creation of many independent and inefficient æislands of technologyÆ where a variety of products from different vendors are used to address different, but related problems. Problems occur with unreliable information, data duplication, data redundancy and transferring data between applications that may be incompatible or even run on different computer platforms. These problems impede the flow and availability of information and hamper day-to-day decision-making by mine management. A solution to this problem is to take a holistic view of all the various technical applications and incorporate them into a single information technology solution. This solution must encompass all of the information requirements of a mining operation and must provide facilities that address much of the modern thinking about mine management, including strategic mine planning, value management, key performance indicators, and maintenance of a mineral balance sheet. Gemcom is developing an Integrated Resource Asset Management System (IRAMS), which is an enterprise-wide integrated computer system that encompasses various applications typically found at a mining operation. The core component of the system is a common, open, industry standard database that can be shared by many users from each of the different departments at a mine. Around that central repository are the primary applications that provide the mine with information it needs to operate. Ensuring that the information is reliable, accurate, shareable, timely and consistent will eliminate many inefficiencies, and provide significant benefits to mining companies. In turn these benefits will lead to significant improvements in decision-making, productivity and profitability for the operation. The initial version of the IRAMS system is currently being implemented at the De Beers Venetia Mine in South Africa. The system is being built around a core repository using the Microsoft æBack OfficeÆ architecture, and incorporates key technical applications from Gemcom, Whittle, De Beers Technical Team, Wenco and JKTech. The benefits of enterprise-wide systems have long been recognised in the commercial arena and enterprise resource planning (ERP) systems such as SAP, JD Edwards and MIMS are becoming commonplace in the mining industry. The more forward looking software developers and mining companies realise the need for efficient management of the information gathered during the mining process and can see that the concepts used in ERP systems apply equally to the technical applications as they did to commercial applications. The use of IT in the mining industry has expanded tremendously over the last five years as enabling technology and management acceptance has become more prevalent, and there is considerable room for dramatic growth over the next five years. The evolution of geological and mining software has now reached the stage where mines will yield the greatest returns by integrating the applications used in each area of their operations.

Jan 1, 1999

By D. T. Pritchard

"Introduction""No accounting system is very good, and all of them are infinitely variable*.”The purpose of this chapter is to discuss those facets of a typical accounting system which are most commonly encountered by operating managers in mineral processing plants. However, before concentrating in any detail on these it is important to understand the broad purposes and basic techniques of any accounting system in any major business.The three broad purposes of an Accounting System are:- Administering, controlling, and recording the flow of cash in and out of the business. Cash is, of course, converted into other assets (or stores of value) such as inventory, plant and equipment, etc. These assets also have to be administered, controlled and recorded.- Internal reporting to Management for information, for control, and for use in making business plans and decisions. - External reporting to stockholders, government, lenders and other outside parties.In this chapter we shall organize our discussion of accounting practice in mineral processing plants around these three purposes of accounting and focus in some detail on specific practices and techniques with which operating personnel will be routinely involved. This chapter is divided into the following: Accounting Basics; Administration, Control and Recording of Cash Flows; Internal Reporting; Planning and Budgeting; Cost Control; and External Reporting."

Jan 1, 1989

By N. Nišić, A. Cvjetić, V. Jovanović, D. Knežević, D. Nišić

The risks associated with operating water reservoirs and tailings storage facilities (TSFs) are different because of their different purposes, methods of construction and operation, and characteristics of the materials impounded and their flow behaviour. Regardless of the differences, these two types of structures are often put in the same category when it comes to risk assessment and the application of relevant methodologies, which may result in unrealistic outcomes. In this paper we investigate whether it is possible to apply the risk ranking methodology designed for water reservoirs to TDFs and overview the key differences between these two types of structures. We also provide a comparative analysis of the results obtained by conducting a risk assessment of the operation of a TSF, applying the method recommended by the International Commission on Large Dams (ICOLD), and analyse the results using the failure mode and effects analysis (FMEA) technique. It is concluded that a more realistic evaluation of risk levels can be obtained by adopting a systematic approach to risk assessment in accordance with the traditional risk definition on which the FMEA technique is based.

Nov 30, 2022

By Harry Littleton, Jr. Scarber, Wanliang Sun

"The Lost Foam Casting (LFC) process is relatively immature when compared to other casting processes. To make the process more robust, computer modeling is needed to reduce lead times and casting defects. In this study, metal filling of lost foam aluminum castings was visualized using state-of-art real time X-Ray technology. Metal filling of the lost foam casting was simulated using a commercial software package. The result of the computer simulation was compared with the results of the real time X-Ray visualization. Some of the computer simulation results agreed with the real time X-Ray visualization, but some did not. Based on other studies using real time X-Ray technology, new input variables, such as foam density variations, were developed for the computer modeling. With the new variables, modeling of the lost foam casting process becomes more realistic. IntroductionMold filling of the Lost Foam Casting (LFC) process is an important step toward making a quality part. In the LFC process, molten metal is poured against a refractory coated foam pattern surrounded by dry sand. At the pouring temperature of aluminum, the foam pattern is decomposed into 30% (wt) gaseous and 70% (wt) liquid foam pyrolysis products. Existence of the gaseous foam decomposition products significantly increases the back pressure on the metal stream compared with the conventional open cavity sand mold. Entrapment of the liquid pyrolysis products during the metal filling generates many casting defects, such as internal pores, fold and blisters. Existence of these casting defects sometimes seriously degrades the quality of the components manufactured by the LFC process. Understanding and controlling the metal filling of the LFC process will certainly make this process more robust."

Jan 1, 2004