Search Documents

By Wael Abdellah

Mine haulage drifts are the primary access to the mining blocks of an orebody in a multilevel mining system of a tabular ore deposit. The stability and functionality of haulage drifts are thus crucial to the success of a mining operation. Drift instability could lead to serious consequences such as injuries, production delays and higher operational cost. In this paper, the performance of the haulage drift stability is evaluated on the basis of the primary rock support system comprising 1.8 m resin grouted rebars in the drift walls and 2.1 m long bolt in the back. Two failure criteria namely the extent of Mohr-Coulomb yield zones around the drift, and linear elastic brittle shear failure are adopted and compared, with respect to lower level and same-level mining and filling sequence in the vicinity of the haulage drift. The case study is one of the #1 Shear East zone of the Garson Mine in Sudbury, Ontario. Random Monte Carlo (RMC) technique, which has been previously established to assess the haulage drift stability, is employed in this investigation. The RMC technique is used in conjunction with finite difference modelling software FLAC for random assignment of model input parameters in the FLAC grid. Deterministic model results reveal the drift behaviour in terms of deformation (convergence) and mining-induced stress distribution. Comparison between the two different criteria is carried out to determine which method is most suitable in evaluating unsatisfactory drift performance. The results are presented in terms of probability of instability and categorized with respect to failure condition and mining step. It is shown that the brittle shear failure condition based on linear elastic response calls for enhanced support system at a later mining step than what Mohr- Coulomb yielding condition does. The paper presents a detailed discussion of the stochastic analysis results.

Jun 1, 2012

By E. K. Albert

In 1977, Congress enacted Title IV of the Surface Mining Control and Reclamation Act (SMCRA), providing for an "abandoned ml.ne reclamation fund". This fund, taken from a fee collected from operating coal mines, provides capital for the reclamation process. However, given the number and extent of abandoned mine sites in some states, the question of project selection is important. This paper describes a project in progress to create a Management Information System application for project ranking under multiple objectives. The benefit of this project for the need of new environmental control technologies will be discussed.

Jan 1, 1990

By Georgene Renner, Chee Theng, William Gleason

"More than 6,300 people attended SME’s 2016 Annual Conference & Expo in Phoenix, AZ and many of them made the trip to the conference to take part in the excellent technical sessions that are presented on a yearly basis by the Society.Holding true to form, this year’s conference was full of options. In fact, this year there were 121 technical sessions and 751 presentations to chose from. The following is a sample of some of the technical sessions as seen through the eyes of the editors of Mining Engineering and SME technical papers.SME Sections Sharing Success: Changing thePublic Perception of MiningThis session was a workshop on how several local sections were effective in getting the message out to their communities and schools about the value of the extractive minerals industry. Several sections shared their outreach successes, including the Mining in Society merit badge activities by the Minnesota Section by Julie Lucas and SME’s participation in the World Scout Jamboree in Japan by Frank McAllister.Dan Alexander highlighted activities by the Pittsburgh Section, such as preparing minerals kits and pamphlets for elementary school classes and regional science fairs. The West Virginia University Student Chapter used the kits as handouts at their local gem and mineral show. School speakers in full mining gear were especially interesting to the young children.Other speakers were Michael Linn, Paradise Valley Unified School District — Business and School Partnerships; and Greg Kruse, Central Wyoming Section of SME — What makes a successful section?Engineering Competency ModelAmerican Association of Engineering Societies and the U.S. Department of Labor, with a grant from the United Engineering Foundation, developed a guide to the set of skills necessary for success in the engineering community -- Knowledge – Skills – Abilities — needed for all disciplines.Various engineering societies are now writing the Tier 5 occupation-specific requirements. The Competency Committee is charged to write concise and discipline-specific mining engineering, mineral processing engineering, geological engineering, and geophysical engineering by Sept. 30, 2017."

May 1, 2016

By Maxim Martel, Karolan Tremblay

Westwood Mine has experienced several episodes of increased seismic activity. While current geotechnical characterizations such as RMR, GSI, and Q' index can identify the general rock quality and zones at risk of convergence, they fail in identifying zones at risk of seismic activity. Previous research at Westwood Mine has shown a correlation between seismicity and areas with strong rheology contrasts. To characterize this contrast, 300 UCS tests were analyzed with their associated geochemical data, and statistical analysis and regression were performed using IOGAS software to establish a relationship between resistance and geochemistry. UCS-generated data with XRF results were transferred to Leapfrog Geo to create a block model of intact rock strength. This block model dataset was used to perform a competency contrast block model, and back-analysis of specific seismic sectors at Westwood Mine were conducted to validate the model. The purpose is to develop an established geomechanical tool capable in identifying areas with greater seismic risk associated to a change in the rock strength characteristics. By identifying those areas, mitigation measures can be implemented to minimize impact of seismicity on the operation.

Jan 1, 2023

By Rodney Trevor Jones, Arthur Robert Barnes

Anglovaal Minerals acquired the Nkana slag dump from Zambia Consolidated Copper mines (ZCCM) in 1998 and embarked on an ambitious project to pioneer the recovery of cobalt from slag using DC smelting technology. Anglovaal Research Laboratories performed initial pioneering smelting tests in a 250 kW DC furnace over a 3-year period before engaging Mintek for three piloting campaigns at the 1.5 MW level. Mintek had previously developed a reductive smelting process, patented in 1995, using a DC arc furnace for the recovery of cobalt from slags. The results of the pilot-plant test campaigns were used as the basis for engineering the commercial 40 MW operation installed at Chambishi Metals plc in Zambia in 2001. This paper traces the development of understanding of the metallurgical fundamentals ultimately used to predict furnace performance, reviews some of the extreme technical challenges faced, how solutions were identified and highlights some of the critical issues identified during piloting and how these impacted both positively and negatively on the final commercial operation.

Jan 1, 2011

By Xiaoqiong Wang, Daobing Wang, Fanbao Meng, Jianbo Wang, Hongkui Ge

"Shale gas has become an important unconventional oil and gas resources. Its effective development relies on comprehensive and accurate understanding of shale gas reservoirs. Rock mechanical properties is one of the important components of reservoir evaluation. Two adjacent black shale samples, which are cored from the depth of 1145 meters in Chongqing, southwest China, are subjected to acoustic emission(AE) test under uniaxial stress and compared with coarse grained granite. The results of synchronous AE, stress-strain and ultrasonic velocity experiments show that shale has weak anisotropy. Compared with granite sample, two shale samples are similar, but their strength, velocity and brittleness are quite different, indicating that shale has strong microscopic heterogeneity. TOC, XRD, SEM microstructure analysis show that total organic content, mineral composition and natural fractures are the main impacting factors for mechanical heterogeneity. INTRODUCTIONShale gas is a typical low-grade marginal resource, which is characterized by ultra-low matrix permeability and small single well control volume. In order to enable commerical development, complex hydraulic-fracture networks must be created in the shale to allow gas to escape from the micro/nano-pores and natural fractures where it is trapped in the rock (C. Clark et al.,2013; Ge et al., 2013). The development of shale gas requires accurate evaluation methodologies to evaluate shale reservoir properties and predict production. (Jarvie et al., 2007). Rock mechanical properties are an important part of the reservoir evaluation. It is significant for efficient drilling, completion and hydraulic fracturing to understand mechanical behavior of shale gas play (John, 2011; Wei, 2013).Rock mechanical properties mainly include heterogeneity, anisotropy, brittleness and acoustic emission activity (Lockner et al., 1992; Jerome et al., 2009; He et al., 2010; Liang et al., 2012). Shale mechanical properties are evaluated from laboratory tests following a complex workflow that covers tasks from sampling to testing (Md. Aminul Islam et al., 2013). It is common to include various experimental methods such as stress-strain curves, ultrasonic velocity and acoustic emission when evaluating the mechanical properties (Rao et al., 2006). Because of the presence of organic-rich matter, mineral composition orientation and natural fractures, shale tends to have strong anisotropy and heterogeneity (Deng et al., 2004; Wang et al., 2013; Hathon et al., 2013)."

Jan 1, 2015

By C. Golumbic

Most early research on solvent extraction of coal has been concerned with the molecular structure of coal. Although rush work is continuing, practical aspects of the subject also are being emphasized. For example, development of the Pott-Broche extraction process resulted from the discovery of very efficient solvents for the pressure-extraction of coal. Recently, Orchin and Storch reported the use of even more efficient solvents under similar conditions. In addition to the discovery of more effective solvents, the possibility of efficient extraction at atmospheric pressure is obviously of practical interest. H. J. Rose observed that phenanthrene at its atmospheric boiling point readily dispersed 80 percent or more of Pittsburgh-bed bituminous coal. This fact served as the starting point of the present investigation, ill which determination of the chemical specificity of this solvent and the chemical nature of the resulting extracts was undertaken. This paper represents a progress report of the results obtained to date.

Jan 1, 1950

By L. C. Graton

At the Tenth International Geological Congress, Mexico, 1906, Waldemar Lindgren presented "The Relation of Ore Deposition to Physical Conditions." Retrospect ranks it as the outstanding offering at that Session and as the most fundamental contribution up to that date on the philosophy of ore deposition. Elaborating thereon in his text-book "Mineral Deposits," Lindgren analyzed ore-forming processes under conditions prevailing from great depth up to surface; explained the nature of deposition in each environment; and developed a comprehensive genetic ore classification, which brought wide acceptance and enriching contributions by many. Since Lindgren's latest edition (1933), have come wealths of material relevant to ore genesis, particularly through amazing renaissance and proliferation throughout science. Current publication regarding ores now emanates largely from a generation caught in pressures of the breathless modern tempo, which tempts scant reflection upon earlier truths. Consequently, today's thrilling output contains not a few offerings that need challenge because supplanting interrelationship and system by what seems, collectively, an assemblage of strange, ad hoc and often self-contradictory concepts. From these latter some merit may eventuate but at the probable cost of present confusion and delayed progress. The following pages, naming numerous post-Lindgren advances, record the conviction, held by many, that Lindgren's philosophy, progressively improved, remains the soundest approach to understanding ore genesis.

Jan 1, 1968

By L. Kaufman

Fifteen boride composites were synthesized by hot pressing and evaluated by physical and incendivity testing as non-sparking tool materials. The incendivity tests, conducted at the U. S. Bureau of Mines, Albany Research Center, compared the boride compo-sites with standard cobalt-bonded tungsten carbide material used for coal cutter bits. Two titanium diboride composites and two zirconium diboride composites out-performed cobalt-bonded tungsten carbide in wear resistance and reduced tendency to cause ignitions. However, three of these candidates exhibited undesirable chipping. The remaining candidate, a TiB2-(Ni, Cu) composite, did not chip, nor did it cause ignitions at levels where cobalt-bonded tungsten carbide tools caused ignitions in the incendivity tests. Thus, this material appears to be a logical candidate for further development.

Jan 1, 1973

By A. Bhagavatula, M. Rezaee, M. J. Kiser, R. Q. Honaker

"A field study of the coal preparation plant fleet in the eastern United States was undertaken to determine if quantify of rare earth elements (REEs) present in the product streams are large enough to justify further concentration. Representative composite samples were taken from the clean product, coarse refuse, and fine refuse streams from 20 coal preparation plants. Each stream was then separated into various size and density classes and analyzed for ash and REE contents. The large database showed that coarse refuse contained the largest amount of REEs, although the ratio of heavy to light REEs was greater for the clean coal products. The concentration of REEs was also compared to that typically seen in the earth’s crust. This enrichment ratio ranged from approximately 1.5 to more than 4.0 as the ash content varied. The database also showed that a linear correlation existed between La and Ce for many REEs of interest, although there were several notable exceptions for some of the high-value REEs. INTRODUCTION Worldwide energy demand is expected to grow by as much as 37% by 2040 according to the International Energy Agency (2014). This growth, coupled with a decrease of the reliance on coal to generate energy, means that it is more important than ever for countries to secure the materials necessary to meet its energy projections. For the United States, the U.S. Energy Information Administration (EIA) predicts that total domestic electricity use will increase roughly 25%, from 3,836x109 kWh in 2013 to 4,797x109 kWh in 2040 (EIA, 2015). In the EIA’s reference case, coal’s contribution to electricity generation drops from 39% in 2013 to 34% in 2040. On the other hand, renewables share of electricity generation grows from 13% to 18% for the reference case. Compared to its current state, renewable energy electricity production is predicted to grow as little as 50% to as much as 121% over this time period, depending on the economic case being examined. This growth will largely be seen in the wind and solar sectors (EIA, 2015). The focus on viable renewable energy resources will be crucial to the future of fueling American growth. Many of the renewable energy technologies, such as wind turbines and photovoltaic films, rely on materials and supply chains outside of the United States. The lack of a reliable and low-cost domestic supply could pose a threat to the growth of the renewable energy markets in the United States. This potential vulnerability recently led the United States Department of Energy (DOE) to create a Critical Materials Strategy Report. In this report, 15 elements were identified as critical for the continued growth of the renewable energy market. Eight of these elements were rare earth elements (REEs). Five REEs (dysprosium, neodymium, terbium, yttrium and europium) were identified as highly critical and vulnerable to shortages (Bauer et al., 2012)."

Jan 1, 2016

By S. Leong

This paper reports on research examining disclosures from mining companies regarding their water usage in the Macquarie and Lachlan catchment areas, both parts of the Murray-Darling Basin in New South Wales, Australia. The objective of the research was to assess whether this disclosure is sufficient to allow communities to determine whether mining companies are complying with mining conditions of consent and abiding by the requirements of their water licencing agreements. These requirements are then compared to the water reporting requirements of the Global Reporting Initiative (GRI) and the Water Accounting Framework for the Minerals Industry (WAFMI). Communities are concerned about whether the mining industry?s use of water will have impacts on their livelihoods and lifestyle and thus require information concerning the quantity of water that will be extracted, how much water will be left for other stakeholders and whether the mining will affect water quality. This is an archival study. It has involved examining relevant publically available information released by mining companies and government regulators and determining if this is sufficient to meet the needs of the local communities. Additionally, it has involved looking at information indirectly provided by mining companies, via the use of intermediaries. Further, information availability concerning basic water accounting and regulatory breeches and whether such information is available at the mine site level has been considered. It is found that while NSW legislation places very little reporting requirements on mining companies, the development consent conditions for new projects and extensions to existing projects are quite significant and should be sufficient to meet the needs of local catchment residents though such information is not always easily accessible for the layperson.

Aug 1, 2013

By S Larbi-Bram, F Shi, E Manlapig

Mining companies have recognised that characterisation of particle breakage plays an essential role in the design and optimisation of comminution circuits. Recently the JKMRC comminution research team has developed a new breakage model incorporating the effect of particle size, and a new breakage characterisation testing device, called the JK Rotary Breakage Tester (JKRBT), which allows rapid testing of particle breakage under high energy single impact and low energy repetitive impact conditions. The latter is believed to be the dominant breakage mechanism in AG/SAG mills. Existing devices, such as the JKMRC Drop Weight Tester, are not suitable for performing repetitive impacts since they are too time consuming. Positive feedback received from mining company sponsors to the new technology has prompted the JKMRC to further validate the device and the model through a formalised experimental test program on professionally designed and manufactured JKRBT machines. The first JKRBT was installed at the Anglo Research laboratory in Johannesburg in March 2007 and four more major mining companies will participate in the project in 2008, with commercial release expected in early 2009. The JKRBT has the potential to revolutionise ore testing, with applications in laboratory impact breakage characterisation of rock samples, drill cores, coal and other materials. It also stands poised to significantly advance the process control of comminution circuits since it is readily adaptable to on-line ore hardness measurement. Can any mine afford to miss out on this technology?

Jan 1, 2008

By A. L. Martikainen

Booster fans increase air pressure to overcome resistance, the objective being to force adequate amounts of air through distant workings. They are used in areas that are difficult or uneconomic to ventilate with main fans alone. Booster fans are currently permitted in underground coal mines in some countries; the United Kingdom, South Africa, Australia and Canada have been defined as major users. Booster fans are not allowed in the US bituminous and lignite coal mining operations at the present time due to safety concerns. This paper presents the history of booster fan use in coal mines of the United States during the last 90 years. Changes in regulations, as well as advantages and disadvantages of booster fan use, are discussed. Research and petitions for booster fan use are highlighted in order to bring the debate into focus.

Jan 1, 2010

By S Slouka

Airborne rock dust poses serious long-term health complications to workers in the underground mining and civil environment where rock excavation is utilised. During drilling, airborne rock particles are immediately released into the breathable environment where additionally, the settled dust can be reintroduced into the air further down in production. The purpose of this study is to build a characterisation suite of dust particles such that underground operations can implement more appropriate dust suppression and mitigation techniques in accordance to pick wear. Therefore, concrete is cut to create a preliminary dust characterisation baseline, where future cutting tests will be performed on limestone and sandstone rocks.In this study, three conical pick wears (new, moderately worn, and fully worn picks) are used to generate dust from a concrete block and characteristics are statistically compared between the dusts. Airborne respirable particles are collected during cutting and deposited fine material, orparticles left on the surface of the block, are collected after cutting. The dusts are then analysed through standardised methods, field emission scanning electron microscope image capture with image analyses, and laser diffraction methods. Findings reveal that the worn pick generated thehighest concentration of respirable dust, all picks generated dust containing quartz, the three picks generally generated respirable dusts with similar particle shapes (in terms of roundness, roughness, and aspect ratio), and the worn pick generated the largest deposited fine material particles.

Oct 12, 2022

By C. H. Mathewson, A. U. Seybolt

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrellce of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below. Conditions of Equilibrium between a Metal and Dissolved Oxide at Different Temperatures and Pressures The general conditions of equilibrium in any system are conveniently summarized in a projection of the triple curves of the P, T, X space

Jan 1, 1935

By A. U. Seybolt, C. H. Mathewson

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrellce of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below. Conditions of Equilibrium between a Metal and Dissolved Oxide at Different Temperatures and Pressures The general conditions of equilibrium in any system are conveniently summarized in a projection of the triple curves of the P, T, X space

Jan 1, 1935

By Timothy Batchler

"Pumpable roof supports are currently being used to provide a safe working environment for longwall mining. Because different pumpable supports are visually similar and installed fundamentally in the same manner as other supports, there is a tendency to believe they all perform the same way. However, there are several design parameters that can affect their performance, including the cementitious material properties and the bag construction practices that influence the degree of confinement provided. A full understanding of the impact of these design parameters is necessary to optimize the support application and to provide a foundation for making further improvements in the support performance.This paper evaluates the impact of various support design parameters by examining full-scale performance tests conducted using the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS) as part of manufactures' developmental and quality control testing. These tests were analyzed to identify correlations between the support design parameters and the resulting performance. Based on more than 160 tests over 7 years, quantifiable patterns were examined to assess the correlation between the support dimensions, cementitious material type, wire pitch, and single-wall vs dual-walled bag designs to the support capacity, stiffuess, load shedding events, and yield characteristics.INTRODUCTIONDeveloped in the 1990s, the first major use of pumpable supports systems in U.S. longwall operations was in the support of bleeder entries (Barczak, Tadolini, 2008). Since then, they have been utilized as yieldable concrete supports to provide a safe working environment for longwall mining gateroads, bleeders, and emergency escapeways while also maintaining adequate ventilation pathways. The basic structure of pumpable roof supports has remained unchanged over the years. Formed in place with a twopart fast-setting grout, the support material can be pumped into a containment bag from several thousand feet away often through surface boreholes. The containment bag then acts as a form to fill the support and provides confinement to the grout during loading and after failure. Pumpable roof supports provide full contact with the mine roof and floor, which eliminates the need for secondary material to establish proper roof contact (see Figure 1). They provide a high peak load capacity and a sustained, confinement controlled yield behavior while maintaining stable ground conditions, which is essential to underground mining operations."

Jan 1, 2016

By A. C. Fieldner

THE Bureau of Mines has received many requests for Information concerning the methods its laboratories use for analyzing coal and coke and determining their heating value. The fuel investigations now conducted by the Bureau of Mines are an outgrowth of the work undertaken at the Government coal-testing plant erected in 1904 at the Louisiana Purchase Exposition in St. Louis, and the methods for proximate and ultimate analysis of coal used by the Bureau of Mines are based on those originally adopted by the chemists of the coal-testing plant and followed in the subsequent chemical work of the Government fuel-testing plants at St. Louis, Mo., Norfolk, Va., and Pittsburgh, Pa. The many valuable suggestions and criticisms received from N. W. Lord, director of the School of Mines, and from E. E. Somermeier, professor of metallurgy, of Ohio State University, at that time, are greatly appreciated; development of many of the methods for the proximate and ultimate analysis of coal now used by the Bureau of Mines is chiefly clue to these men.

Jan 1, 1951

By G. S. Hume

In the transformation of carbonaceous materials, such as peat, to coals of various grades, the changes are known to be both physical and chemical and the grade of coal finally produced depends on the stage to which alteration proceeded. Those changes, which are frequently spoken of as the results of metamorphism, are due to pressure with accompanying heat and, according to the amount of metamorphism to which the sediments with the included carbonaceous beds have been subjected, there is a gradation from peat to anthracite coal, and even to graphite. The improvement in the quality of the coal as a result of metamorphism is due to an increase of the carbon content of the coal and a corresponding loss of the volatile materials. This rise in the quality of the coal according to the degree of metamorphism is well illustrated by the coals of western Canada. In the Plains area, where the deformation and the attendant metamorphism of the sediments is comparatively small, the coals are lignites, whereas in the mountains, where deformation has been severe, the coals are semi-anthracites. Sub-bituminous and bituminous coals occur in the intervening areas. The same general relationship between the quality of the coal and the degree of metamorphism holds true for the Appalachian basin of the United States, where there is a progressive improvement in the quality of the coals from west to east, that is, from an area of comparatively slight metamorphism to an area of marked deformation in the Appalachian Mountain region. But while it is true that this relationship holds in a general way, it has been found that the improvement in the quality of the coal is not always uniformly progressive, and there may be local variations such that an area containing coal with a carbon content indicating low or medium metamorphism may be surrounded by areas in which the coals are of higher grade. These local variations in many cases can be explained, and they in no way detract from the general rule that, in a region exhibiting a progressive betterment in the quality of the coal from an area of low metamorphism to one of more marked deformation, the quality of the coal, i.e., the amount of fixed carbon in the coal, may be taken as an index of the degree of metamorphism of the coal as well as of the sediments in which it occurs, It has been pointed out (') that certain coals, such as cannels, are unreliable indicators of the varying degree of metamorphism because of the nature of the material from which such coal was derived. Such coals, however, are not known in western Canada and their behaviour need not here be discussed.

Jan 1, 1927

By R. Haecker, S. Bajic, R. Thorpe, A. Palko, M. Kalstrom

"Historically, mineral processors have used inferential data like plant instrumentation, assays, and grind sizes to monitor the performance of their plants. The ability to monitor the minerals themselves on a daily basis has eluded all but the very largest and richest of operations. The advent of a new generation of compact, robust, and user-friendly SEM-based automated mineralogy systems looks set to accomplish this, aiming to bring daily mineral monitoring of plant performance within the reach of all mills from mid-size upwards. This paper describes the use of this machine at Greens Creek Mine, a 2.5 ktpd Ag-Au-Pb-Zn operation with a complex flotation flowsheet. During the trial, the machine provided turnaround from sample collection to reporting averaging 24-36 h for key daily samples. All equipment was located within the compact mill, and proved highly reliable despite the challenging environment. Turnaround time was fast enough for metallurgists to understand, and, where possible, respond to ore and process changes while they were still happening. The plethora of data generated was filtered to a simple report whereby mill management could quickly absorb key daily mineral-based performance indicators. This paper will describe how the data was used to understand the key drivers behind metallurgical efficiency at Greens Creek, and how metallurgists began using the information to enhance daily mill performance."

Jan 1, 2014