Search Documents

By S. Parent, J. -F. Lepage, S. Glover

"Goldcorp – Eleonore’s 7 000 tonnes per day gold mill was started up in October 2014 and achieved commercial production in April 2015. During the first year, operation has faced challenges from grinding, flotation, sulfide cyanidation and tailing filtration to achieve targeted throughput, availability and recovery.The optimization of non-sulfide tails filter cloth lifetime and filter press availability had the most significant impact on ramp-up of both mill throughput and availability. A change in steel ball addition size to the grinding circuit was made to meet the targeted p80 of 65 µm. Various optimization efforts were conducted on the flotation circuit, intended to recover all sulfide-bearing minerals. The goal is to attain the environmental target of 0.12% sulfur in flotation tails (to eliminate acid mine drainage or AMD), while an average of 0.31% sulfur was obtained over the first months of 2015. Collectors, frothers, activators and hydrodynamic parameters were tested to improve the circuit desulfurization efficiency. High sulfide reactivity in pre-oxidation and cyanidation severely impacted dissolved oxygen levels and cyanide consumption. Studies were undertaken to understand the effects of mineralogy, grind size and leach conditions on gold dissolution kinetics and cyanide consumption. Efforts were focused on pre-oxidation to restore dissolved oxygen levels as well as optimizing both lead nitrate addition and pre-oxidation time.INTRODUCTIONGoldcorp Eleonore’s mill commissioning started in September 2014. It was considered to operate the mill at 3 500 tpd during design, as the mine was planning to operate at this throughput for the first year. However, with the stockpile of ore and a higher throughput from the mine, the mill was able to run at higher tonnage than initially anticipated.While increasing tonnage, a few bottlenecks were discovered and overcome in areas such as filtration and cyanide destruction. There were also recovery issues which were addressed in areas such as grind and sulfide leach. This paper focusses on the first complete year of operation ending September 30th 2015. A process description and the flowsheet are presented below and it will then go into detail about operational, metallurgical, mechanical and design issues experienced during the year."

Jan 1, 2016

By RALPH BALTES, AMIR EHSAN KIANFAR, FABIAN UTH, ELISABETH CLAUSEN

As indoor positioning provides particular challenges due to the unavailability of GPS signals, various systems such as ultrawideband (UWB), radio frequency identification (RFID), ultrasound, and wireless local area network (WLAN) have been proposed in recent years. Some of these technologies are currently being marketed and some are still being developed. UWB technology allows for higher precision while also reducing power consumption. Hence, the underground automation and localization systems can use this technology for more accuracy and robustness. This article discusses new robust UWB modules used for underground positioning and collision avoidance with regard to human safety in underground mining operations.

Jul 31, 2020

By A. B. Holland-Batt

Deposition velocities play an important role in many fields of engineering and an impressive range of measured data has accumulated in the literature. Numerous workers have addressed the problems that are associated with the prediction of deposition velocity because of its particular relevance to the design of pipelines and pumping stations. However, despite this extensive effort, the calculation of friction heads still requires reference to experimentally based graphs to determine Durand factors and there is still scope for improvement in the prediction of the deposition velocity at different solids concentrations. Equations to characterise the relationship between the Durand factor and the volume concentrations of solids in the slurry are presented. A correlation for the prediction of the deposition velocity is also developed and tested against some of the classical experimental data. The application of predicted values of deposition velocity in assessing the potential for the sanding-up of spiral separators is then described and a case study is presented.

Jan 12, 1992

By Sunil Katharia

In February 2016, the upgraded Blast Furnace 1 of JSW Steel Limited (JSW) at its Vijayanagar Steel Plant was blown in after a 6 months shutdown in which the whole furnace was rebuilt on the existing foundation and within the existing tower structure. Despite several plant constraints it was possible to increase the furnace inner volume by 85% - reaching 2307 m3 from existing 1250m3. The upgradation project covered the stockhouse and its dedusting system, top charging system, furnace profile, furnace cooling system, casthouse and its dedusting system, slag granulation plant, pulverized coal injection plant, hot blast system and gas cleaning plant – with major interventions in order to cope up with the changed operating conditions. The total scope of the project was split by JSW into several packages, all based on design data provided by Paul Wurth. JSW was responsible for coordinating the local subcontractors along with Paul Wurth which has been appointed as main technology supplier in charge of complete basic and selected detail engineering in the key areas and of the supply of core equipment such as the Bell-less Top®, copper staves, GCP key items and TMT casthouse machines. The main design concept and the key points of the project such as optimization of project ROI, advanced erection concepts as well as a summary of the operating results are presented confirming JSW “BF1” upgradation as one latest examples of the current state of the art in the revamping projects.

Aug 17, 2017

By DJ McKEE

Process control emerged in the mid-1960s as a new and exciting method of improving the performance of mineral processing operations. The early Australian developments, principally in Broken Hill and Mount Isa, were based on pioneering work in instrumentation, the availability of small digital computers and a particularly effective partnership between companies with technological foresight and University and CSIRO research groups. Initial progress was rapid and within ten years many plants were committed to process control. Process monitoring is now routine and most circuits have some level of control. However, few plants have comprehensive optimising control systems as the difficulty of developing control strategies which can cope with the wide variety of conditions encountered in most mineral plants has been fully appreciated. This paper summarises past experience and assesses the degree of application of different forms of process control in metallurgical plants. Barriers to the effective utilisation of opt rising control are identified and some suggestions for advancing the application of control are made.

Jan 1, 1992

By G. R. Lane

My opportunity to serve as President of the prestigious Southern African Institute of Mining and Metallurgy (SAIMM) was made possible by an Anglo American scholarship 39 years ago—a pivotal moment that set me on a career path spanning various roles and start-up ventures in the mining industry. Over the past decade, I have been privileged to broaden my experience by consulting across diverse industries globally. This exposure revealed something profound: what I had previously considered mining-specific challenges are, in fact, universal across many sectors. At its core, a mining operation is a complex system of interconnected activities—from exploration through mining operations like drill and blast, load and haul, to beneficiation, and outbound logistics. My cross-industry work has clearly shown that diverse sectors, such as chocolate manufacturing, tissue paper production, toilet paper converting facilities, labgrown diamonds, or high-tech equipment lifecycle management, all rely on value streams of interconnected activities to transform products. The objective is to maximise throughput while effectively managing performance variability. The primary difference lies solely in the specific technical expertise required for each industry, such as chemical, mining, processing, or metallurgical engineering. Across all these industries, I have observed a consistent pattern, that is, performance is primarily driven by individual efforts, where people react and work diligently as situations unfold in real-time. General managers and their teams often operate tactically, focusing on explaining yesterday’s poor performance rather than proactively setting up operations for success. This often resembles an ‘‘under-7s soccer match’’, with everyone chasing the ball. The common response to issues is to add more ad hoc meetings. This effort-driven organisational behaviour persists regardless of whether operations are greenfield digital manufacturing facilities, advanced digital mines with advanced process control, or operations run on paper and Excel spreadsheets for data acquisition. Paradoxically, more real-time data can lead to increased data noise, greater indecision, and sometimes, lower performance. Despite value streams often operating significantly below capacity, organisations continue to invest heavily in additional equipment or in ‘‘glossy brochure promises’’ of Industry 4.0 digital technology and real-time data solutions, which frequently fail to deliver value. This leads to a critical question: Have we underinvested in our most valuable resource— people? Even Tesla faced this challenge with their underperforming fully automated Model X facility. We must shift our focus to designing the ecosystem, or operating model, of our organisations. This extends beyond the traditional triad of people, process, and technology, and moves beyond simplistic views of change management. Artificial Intelligence (AI) has the potential to add significant value, but it also introduces another layer of complexity into designing the organisation of the future. My full presidential address below at the SAIMM AGM discussed the symptoms of an effort-driven organisation and covered the fundamental building blocks and requirements of an operating model, including recommendations on implementing a people-centric approach.

Oct 2, 2025

By J. B. Mawdsley

From the view point of the mining engineer, the square-set method of stoping as practised at Butte, Montana, is one ?of the outstanding features of well conducted mining operations in that camp. The following information was obtained in the course of two months underground work in the Granite Mountain mine, during the summer of 1920, which is one of the properties of the North Butte Mining Company, situated on the well known Speculator vein. Most of the information was derived from personal observation and from discussions with various miners and with members of the staff. Geology The copper mining area of the Butte district is some two miles long by one and a half miles wide, a mineralized area in a great batholith of monzonite granite, locally known as the Boulder batholith. This extensive body of granite is traversed by several series of mineralized fault-fissures which differ in strike but generally dip steeply. Geologists agree that following the formation of the fissures, alkaline solutions ascended and decomposed the felspathic portions of the granite in the immediate vicinity of the fissure walls, and that these alkaline solutions were followed by cupiferous solutions which filled the fissures and replaced the granite next to the walls. A zone of oxidized ore, varying in thickness from 10 to 400 feet, overlies a sulphide zone containing chalcocite, enargite, bornite and chalcopyrite, with a small amount of quartz gangue. The veins are from 3 to 100 feet in width and contain, on the average, 3 per cent of copper, 2 ounces of silver, and 15 cents in gold per ton.

Jan 1, 1925

By M. H. ElMaghraby

This paper describes the development and validation of a strategy for vibration-based online detection of faults in a particular class of machinery commonly found in industry. This machinery is defined by two basic characteristics that preclude it from the application of standard online condition monitoring approaches. The first characteristic is that the machine is in a constant state of transient operation, thus making it difficult to differentiate between changes in transducer measurements that are due to variable duty and those that are due to machine malfunction or fault. The second characteristic is the fact that the machinery involves multiple sub systems that are subject to identical and simultaneous loading, operating environments and duty cycles. An example of such machinery is a system of multiple hydraulic pumps driving a common load. The monitoring strategy presented here employs an anomaly detection scheme together with methods of signal processing and feature extraction that exploit the parallel duty arrangements of this equipment. Preliminary data is collected from a pair or motor-gearbox assemblies used in a material haulage system in the mining industry. Testing and validation was performed on a mechatronic test bench with both healthy and faulted components. Experiments were carried out to investigate how various configurations of the system were able to detect different types of faults. The results indicate that this approach is effective and merits further investigation.

May 1, 2013

By FREDERICW K. BRADLE

I HAVE been puzzled by two lines of thought'; one emanating from Washington, D. C., to the effect that we must all cheer up, that in a very short time, measured in terms of months, prices would begin to recover, business would become normal, and prosperity would continue on its way just as before the interruption of a year ago; and a second, coming from certain industrialists and economists, expressing fears that all commodity prices were in for a long downward trend, which would cause much unemployment, eventually drag down wages and so restrict purchasing power as to further aggravate the situation. One basis for the fear of a downward trend in commodity prices' is that ifter great wars a depression could last for something like 40 years-the downward trend to such a depression after our recent World War having been postponed for some reason or other; and the basis for another fear was that the production of gold was becoming less. I had 'also been trying for some time past to refresh my recollection as to how my ow11 particular lead interest climbed out of the depression of 1893; and as all the metals have had, and still have. relative values and prices, I can best express what I have in mind by talking principally about lead.

Jan 1, 1930

By P. Saha, D. M. Chakrabarti, J. P. Srivastavam, P. Bhattacharyya, B. R. Sarkhel, Banerjeem B.

The phosphatic soil deposit at the Sukulu hills region of Uganda contains 10-12% P2O5. The ore occurs as a naturally degraded soil deposit containing a very sticky slime composed of earthy lateritic minerals. Desliming of the ore, which is imperative for its further beneficiation, is an extremely difficult hurdle to overcome for its commercial utilisation. Earlier studies on samples of the same ore at the National Metallurgical Laboratory (NML) and abroad established that it was necessary to pass the ore through a series of three stages of desliming, each consisting of a step of vigorous attrition scrubbing followed by hydrocycloning, for effective elimination of the sticky slime. In the present paper an innovative use of the very strong shear-fields created inside a hydrocyclone has been discussed, that could effectively eliminate the stubborn slime from the ore. The standard design of the hydrocyclone was suitably modified to increase the shearing effect on the slurry. It was possible, through the application of this modified hydrocyclone, to not only totally eliminate all the stages of attrition scrubbing, but also to reduce the subsequent stages of hydrocycloning. The modified technique yielded a concentrate of grade comparable to that obtained by employing the earlier more complex flow sheet, with about 25% higher P2O5 recovery.

Jan 1, 2003

By Joe Zelanko

In order to prevent roof fall accidents and injuries, U.S. underground coal mine operators must develop and implement effective roof control strategies. Various tools are available to assist engineers in developing designs. For example, criteria to address global stability issues (e.g., pillar stability) are well established in the U.S.; effective tools (e.g., empirical and numerical) are available to diagnose potential problems and avoid catastrophic failures. However, most miner injuries occur as a result of local instability (e.g., a roof fall in a single heading or a rib roll from a pillar corner). Hazard recognition and the availability of support plans suitable to those conditions are key to maintaining stability and safety on the working section.

Jan 1, 2011

By L. M. Sandoval, R. Kaunda, C. N. Vasquez, S. C. Falcon

Artisanal and small-scale mining (ASM) involves a wide range of practices, from highly informal and minimally mechanized mining operations with predominantly manual work to formal practices carried out by small but high-tech industrial mining operations [1]. ASM may be a traditional practice, with skills passed from one generation to another. It can be an important driver of local economic development, while simultaneously contributing to a complex array of positive and negative socioeconomic and environmental impacts. There are more than 100 million artisanal and small-scale miners in 80 countries worldwide, and they supply around 20% of the worldwide gold production [2]. According to the Peruvian Ministry of Energy and Mining (MINEM), in 2020, 32% of fatal accidents in formal (legal) Peruvian mining operations were caused by groundfall events [3].The lack of resources, knowledge of best practices in health and safety, and insufficient equipment used in ASM make the probability of suffering work accidents very high. Furthermore, groundfall is one of the main causes of accidents and injuries in underground mines around the world [4], and it is also a concerning problem in ASM, where the associated fatality rate is similarly high. Unfortunately, a proper record of accidents in ASM is not kept, so an estimate of the actual number of groundfall accidents cannot be accurately developed [5]. Currently miners rely on empirical and observational tools acquired through previous experience to assess groundfall risks. The risks for artisanal miners can tend to be significantly greater than risks for those from the mining industry. This is due to the lack of regulation of ASM, which tends to operate outside the legal framework and the regulations lack of enforcement in force for occupational health and safety regulations.

Mar 2, 2022

By L. J. Su, J. Y. Zhang, P. W. Gu, J. F. Xu

Surface tension of mold flux is a key factor affecting optimum casting conditions. A thermodynamic model was developed to determine the surface tension of mold flux containing fluoride based on the ion and molecule coexistence theory of slag structure and Butler’s equation. The relationship between composition and surface tension was investigated by this model. Results indicated that the calculated values showed good agreement with literature data, and the average error was 8.19%. The surface tension value of the CaO–Al2O3-based mold flux was larger than that of the CaO– SiO2-based mold flux. The surface tension in a multi-component system decreased with increasing contents of SiO2, CaF2, and Na2O, which are considered surface-active components. This trend was more significant in the CaO–Al2O3-based mold flux.

Dec 11, 2024

By G. M. Martinez

A cell concept adaptable to large-scale electrowinning of zirconium metal from zirconium tetrachloride was investigated by the Federal Bureau of Mines. Tests were made in twin cells, each 12 inches in diameter by 33 inches long. Electrowinning was performed in one chamber from which the electrolyte was transferred after electrolysis to the other chamber where it was renewed by the introduction of ZrC14 by direct sublimation. The formation of a salt plug in the connecting pipe provided a seal between the chambers. Optimum electrolyte composition, with respect to quality of the metal product (91 pct meeting ASTM standards except for the oxygen content) and current-carrying capability (about 350 amp) was determined to be 16.7 wt-pct NaF-83.3 wt-pct NaCl mixture plus ZrC14 equal to about 3 wt-pct zirconium. A twin-cell design incorporating the unit operations covered by this investigation is proposed.

Jan 1, 1976

The relationships between Aboriginal Traditional Owners and mining companies have often been mired in dispute, particularly since the High Court Mabo decision and the Native Title Act of 1993. In the Pilbara region, Rio Tinto Iron Ore (RTIO) impacts the traditional country of 12 Aboriginal Traditional Owner/language groups. Over the past 12 years the company and the Traditional Owners have negotiated and settled several significant land use agreements including the Yandi Land Use Agreement over the Yandicoogina mine in 1997, between Hamersley Iron (now Rio Tinto Iron Ore) and three language groups û the Bunjima, Nyapaili and Innawonga people and the Eastern Guruma Indigenous Land Use Agreement (ILUA) of 2006. These substantive agreements are now being followed by a new generation of region wide ILUAs which are close to conclusion. Arising from these regional agreements is a new framework for engagement which has been informed by the implementation of the previous agreements in the Pilbara and across the Rio Tinto group of companies. They are driven by both a company desire to have a consistent approach to engaging with Traditional Owners and the Traditional Owners wanting to have a similarly transparent and consistent standard of performance by the company in implementing the agreements which can deliver improved employment, cultural heritage engagement and direct and indirect benefits for the life of mining by the company. During the past three years the growth in the Pilbara, Western Australia brought new opportunities with people flocking to the region for employment flowing from the mining boom. Housing was at a premium and FIFO (fly-in, fly-out employment arrangements) was developed as a method to manage the general growth and demand for skills. Despite the recent down turn in the world economy since September 2008, which has reduced demand for minerals, the Pilbara continues to enjoy high levels of employment and as a result there is still significant pressure on housing and services provision. Although there has been vast economic growth in the Pilbara not only by mining companies but also oil and gas companies, the 2006 census data indicated that the direct benefits of improved employment, business development and engagement in the mainstream economy continued to exclude Aboriginal people. Indigenous people constitute a significant proportion of the population in the Pilbara region, some 6000 people û currently 14 per cent of the population rising to 18 per cent by 2015 û yet they remain at the bottom of the socioeconomic scale. More than 40 years of mining has returned relatively little to this group of people who are the permanent residents of the region and are connected through their traditional culture to this country (Taylor and Scambary, 2005). Ensuring local Aboriginal participation in the mainstream economy has been a challenge for resource companies, Traditional Owners and local residents in the Pilbara. The case study explores the relationship between a mining company û Rio Tinto Iron Ore and the Traditional Owners of the Pilbara. It examines two projects that have been developed to engage Indigenous people in the development of their region and through regional representation and business development to build a sustainable future for themselves and their future generations and at the same time ensure social cohesion to support social licence to operate. The case study also examines the process that was followed by Rio Tinto Iron Ore and its operations in undertaking a regional agreement for land access, participation and the integration of local Indigenous people into their business and the local economy.

Jan 1, 2009

By Gerardo Vargas

Without an adequate data sample there can be no Reliability Analysis (RA). Without analysis there can be no systematic, verifiable improvement in reliability or in operational economy. A sample is a collection of life cycles. A beginning and ending event define a failure mode life cycle. Well known obstacles impede the reliability engineer in his role to analyze maintenance data. The main problem lies in the difficulty to obtain analyzable data samples. Although modern Computerized Maintenance Management Systems (CMMSs) should provide the needed information they rarely deliver samples of adequate quality. Cerrejon, an integrated mining operation in Colombia, South America solved the information management problem by applying a "Living Reliability Centered Maintenance (LRCM)" process to its fleets of Trucks, Graders, Dozers, Loaders, and Shovels. This paper describes a method wherein completed work orders capture reliability analysis enabling information. The 'right' maintenance observations reference significant failure modes. Work orders link to records in a continuously growing Reliability Centered Maintenance (RCM) structured knowledge base. Grouped and filtered knowledge-to-work order links, being instances of failure modes, provide the samples required by reliability analysis software tools and methods. LRCM software and related procedures facilitate the growth of knowledge, manage the work order-to-RCM relationship, and generate samples for subsequent reliability analysis.

May 1, 2011

By F. Mwaura

"The aim of the audit was to determine whether the mining project environmental impact assessments (EIAs) in Kenya are undertaken according to international best practice. A sample of 50 EIA reports for the 2007–2016 period was evaluated using 18 criteria in the Environmental Law Alliance Worldwide (ELAW) guidelines. The findings showed that only two criteria were considered ‘excellent’ according to the ELAW guidelines, namely baseline environmental assessment and prediction of physical impacts. Six criteria were found to be ‘satisfactory’, including prediction of social impacts, analysis of alternative options, and impact mitigation. The reports were quite weak in terms of: consideration of all phases in the mining cycle, environmental regulatory framework, prediction of biological impacts, stakeholder consultation and engagement, integration of human right issues, and integration of climate change and cost-benefit analysis. It is therefore recommended that the Kenyan National Environment Management Authority (NEMA) should consider tightening the EIA terms and conditions in the approval of statutory terms of reference (ToR) for full-scale mining EIAs to ensure improved performance of EIA as a tool for environmental protection. IntroductionThe nexus between society and the environment has continued to generate interest because the environment is the source of goods and services that sustain the various needs of human beings as outlined in the UN sustainable development goals (SDGs) (Armstrong and Peart, 2000; Sutton 2004; Chakrabarti 2007; Strange and Bayley 2008). All the five generic categories of societal needs, namely physiological needs (food, water, clothing, medicines, etc.), residential and occupational needs (shelter, transport, energy, etc.), economic needs (tradeable goods and services), leisure and recreational needs (tourism), and cultural and spiritual needs (e.g. sacred resources and ecosystems) (Mwaura et al. 2016) are addressed by the environment. Consequently, a wide range of development sectors have been established around the world in order to address the above needs (Lederer, Galtung, and Antal, 1980; Rammelsberg et al., 2006; Noonan, 2014). All these development sectors rely entirely on the environment for their proper functioning, as shown in Table I."

May 1, 2019

By W. W. Agey

An inexpensive technique that laboratory studies indicated would significantly reduce seepage in irrigation canals was devised and tested through research sponsored by the Bureau of Reclamation and the Missouri River Basin Field Committee. Laboratory tests simulating optimum field conditions determined that easily applied sodium carbonate solutions made test beds of canal lining materials virtually impermeable for long periods. The study comprised alternative laboratory treatments of 3-inch-deep test beds of canal earths with 74 water-soluble chemicals in search of one 01' more that would effectively improve the water barrier characteristics of the component clays. Sodium carbonate, one of the least expensive, was among the most effective. The addition of 0,4 lb of reagent per sq yd greatly reduced the seepage from typical, highly permeable test beds. The reagent penetrated and sealed surface for about a 1.5-inch depth.

Jan 1, 1965

British Coal has made a practical progressive approach to improving the reliability of its mining equipment. Reliability must be addressed at the specification stage but does not end there and routine procedures are used to procure equipment of adequate reliability. The techniques used to monitor and improve reliability during the operational phase of the equipment, providing engineers and operators with detailed printouts, together with the types of maintenance employed, ensure high levels of availability. Finally, the methods of repair and overhaul of British Coal equipment and systems ensure that the initial reliability targets outlined on the specification, can still be achieved.

Jan 1, 1991

By R. Bhaskar

The control of quartz levels in the respirable dust requires an approach different from that used to control respirable coal dust. The unique physical properties of quartz have to be utilized when developing quartz dust control systems. Also, techniques that modify the surface properties of quartz dust so that conventional dust control measures are effective should be explored. For instance, the wetting characteristics of quartz can be modified so that the capture efficiency of the quartz dust can be improved. Foam sprays assist in modifying surface wetting characteristics. This paper summarizes the results of a study that was conducted in an operating mine to evaluate the effectiveness of a compressed air foam spray system installed under the boom of a continuous miner and directed so as to cover the pan and the gathering arm. The objectives of the study were to evaluate the effect of the foam underboom sprays on (1) the respirable dust concentration in the ambient air, (2) the quartz concentration in the respirable dust. The engineering design of the foam generation and delivery system is described in the paper, followed by a description of the mine and the dust sampling strategy. The data were analyzed to study the effect of foam on respirable dust and quartz concentrations at the miner cab, face return and the intake. The results of the data analyses and costs are presented in the paper.

Jan 1, 1991