Search Documents

By R. F. Tenney

The performances of four anthracite-burning stokers have been observed under identical 74-hp. steam boilers. Fifty runs of 12 and 24 hours' duration were made in accordance with the test code of the American Society of Mechanical Engineers (ASME). The capacity of each stoker for burning anthracite has been determined, the heat efficiency at each fuel rate has been computed, and the various significant items of hear loss have been estimated. The operating data and results from each run are tabulated in this report in the form used in the test code. The heat efficiencies and most significant operating data for each run are also presented graphically for each stoker to establish the trends with increasing boiler outputs, The tests show that rice anthracite can be burned on stokers adapted to its use at heat-conversion efficiencies of 82 percent or more under continuous firing. These high efficiencies are maintained with fuel inputs 30 percent higher and lower than the peak efficiency rate. Moreover, a heat efficiency of 70 percent or more is obtained at 50 percent of the optimum fuel rate, even though the excess air into the furnace cannot be held below 150 percent.

Jan 1, 1960

By S Wilkinson, S Black, L van den Berg

"The mine ventilation system plays an important role in mitigating human exposure to diesel particulate emissions (DPM), exhaust gases and heat in underground mines. The mine’s secondary ventilation systems are critical for diluting contaminants when working at the face of a heading. To improve these systems it is important to understand and visualise the localised air flow profiles. We have considered an approach that includes both tracer gas measurement–modelling to analyse this complex flow behaviour in a heading. The use of tracer gas enables reliable measurements of flow behaviour and differentiation between the contributions of various contaminant sources including DPM. A pilot study was conducted to demonstrate how tracer gas can be used to directly measure the effectiveness of ventilation dilution in a heading during shotcrete activity. This activity is considered to be one of the more challenging areas for diesel exhaust exposure management. Exposure sources include the diesel engine of the spraying equipment (Spraymech) and concrete agitator truck (Agi) that supplies the shotcrete. During operation both the Spraymech and Agi operators are located outside the equipment’s air-conditioned cabins and both are exposed to diesel exhaust. In the pilot study tracer gas was injected directly into the Spraymech exhaust stream. This allowed thorough mixing, ensuring the tracer gas was able to track exhaust gases and particulates released to the heading. The release was repeated at three different headings with varying degrees of secondary ventilation controls. The study showed that small changes to the secondary ventilation system can significantly impact the contaminant concentration. It also demonstrated that tracer gas can be used to isolate different contaminant sources. The intent is to use this technique in a more comprehensive study to develop best practice guidelines for secondary ventilation installations. This paper presents the technique used and the preliminary results from the pilot study. CITATION: Wilkinson, S, van den Berg, L and Black, S, 2015. Application of tracer gas flow profiling to improve secondary ventilation practice – a pilot study, in Proceedings The Australian Mine Ventilation Conference, pp 345–352 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By A. Baldwin

Reports technical progress in designing four machines to be used in mining coal underground, applying innovative concepts at the design stage (instead of add-ons). A study phase was followed by design activity, including calculations supporting the designs. Scale models of three machines were built, and a full-scale mock-up of the conventional loader was used to measure human factors parameters.

Jan 1, 1976

By M. R. Fletcher

Slags generated by the ferrous-metals industry can be used to produce high-tech ceramic materials. The properties of these ceramics can be controlled by judicious choices of composition, additives, and processing parameters. Standard methods of materials handling, such as comminution and mixing, are as applicable to slag as to any other mineralogic raw material. In this study, foundry slag was ground, homogenized, melted and formed to produce a glass, and then heat treated to crystallize it into a high-strength glass-ceramic. The product shows promise as a low-cost wear-resistant tile material which can be custom cast. This and similar materials, made from slags and natural rocks, are candidates for use as construction materials, acid-resistant piping, shock-resistant sheathing, rot-proof pilings, and, when foamed, even as pontoons.

Jan 1, 1988

By Jian Zhou, Shuai Huang, Wenqin Xi, Kun Du

The deep oceans harbor a wide variety of mineral resources that are characterized by their abundance and high quality. Nations worldwide are actively pursuing the exploration and extraction of these resources. This paper provides a concise overview of the mineral resources found in the deep sea, highlighting the challenges associated with their exploitation. Furthermore, it presents a comprehensive analysis of the historical development of deep-sea mining technology and equipment, offering valuable insights into this field. By examining the current issues and obstacles faced in deep-sea mineral extraction, this study concludes that the future of deep-sea mining lies in the direction of automation, intelligence, and standardization. Additionally, it identifies the key technological advancements that need to be achieved in order to overcome the challenges associated with deep-sea mining.

Jan 5, 2024

By James E. York

At a meeting of the American Society for Testing Materials at Atlantic City, June, 1908, Dr. C. B. Dudley, in his presiden-tial address,' showed the vital necessity of not only making a steel rail as good as in the past, but of making it considerably better in order to meet the present and prospective requiremeuts of railroads. Doctor Dudley requested the co-operation of all who from personal experience could give information that would result in bringing about the production of a steel rail that could be relied upon to meet the present requirements. I have had considerable experience in the practical manufacture of steel of almost every grade, during the past 40 years, and I shall suggest changes that will bring about the results desired. Doctor Dudley has had a long experience as chemical and metallurgical expert for the Pennsylvania railroad, but he frankly admits that up to the present time both he and other metallurgical authorities lack the practical knowledge of steel-making that is necessary to state correctly the reasons for the unreliability of the steel rails now produced. The necessity is self-evident for more positive practical knowledge on the part of these experts of what is possible and what is impossible regarding the practical manufacturing of steel rails from the ingot to the finished product. Chemical knowledge in steel-making is far ill advance of what it was years ago, and might be said to cover every requirement (in that department) for producing reliable steel. The study of the metallography of steel has been of great value, also the physical testing of steel, but this knowledge will only de-

Jan 1, 1910

By R. R. Sayers

The hazards connected with work under abnormal air conditions are becoming of increasing importance from a financial as well as a physiological stand- point, due to the extension of compensation laws to include diseases caused by dusts, toxic gases, and abnormal temperatures and humidities. The United States, with the excention of California, North Dakota, Wiscon- sin, Massachusetts, and Connecticut, is the only English-speaking country to-day where silicosis is not compensated.3 Cases of permenent total disability or death due to silicosis mar aprear in common-law courts, particularly in the States that have not recognized silicosis as an occupational disease for which compensation should be provided. Such cases have recently been tried in one State, according to a magazine editorial, not providing scheduled commensation for employees affected by silicosis, with results favorable to the claimant. Clearly established cases definitely linked with occupation as the cause may be expected to be recognized as deserving by juries and courts, and awards will be made. In one Atlantic Coast State, according to this editorial, 108 claims for silicosis, including 21 deaths therefrom, are said to have been filed against two small plants engaged in finely pulverizing quartz sand.

Sep 1, 1932

By Chris Twigge-Molecey, John Peacey

To meet the business objectives of a metallurgical project, there is often a need for new and untried technology or equipment, whose very novelty can present serious risks to meeting those objectives. The key risk management approach is a rigorous stepwise progression from theoretical evaluations and laboratory tests to pilot plant trials. These must be followed by demonstration-scale trials before final construction of a commercial scale plant, paying particular attention to the magnitude of the scale-up between phases. Success depends on following a well-defined program, not eliminating any steps, and ensuring adequate resources are available to the development team. Chapter 6 discusses the nature of technology risks to metallurgical plant projects, and the rigorous management practices needed to identify, analyze, evaluate, and avoid or mitigate them.

Jan 1, 2015

Low-cost housing, like automobiles, should be appraised in the light not merely of first cost but of upkeep as well. Even more important than the number of miles the family car will go on a gallon of gasoline is the number of days the family home can be kept comfortable on a ton of fuel. A furnace tender who tossed every third shovelful of coal into the ashcan would lose his job promptly, but the effect is the same when homes continue year after year to pour out precious heat through uninsulated roofs and walls, Greater economy in household heating means even more to the national economy than to the individual, especially now that we are preparing for defense. Our fuel resources, although large, should be conserved. If less fuel is used for civilian needs, augmented requirements for defense can be met without unduly increasing the number of men needed at the coal mines and oil ells or adding new producing units that might complicate ultimate readjustment to peacetime conditions when the emergency is past and over-expansion of many industries brings new problems if unnecessary demands for transportation facilities are reduced, public carriers will be able to haul more munitions, and manpower needed for national defense will be released; and by protecting workers from health hazards in their homes additional man-hours of productive effort will be gained. Moreover, reducing the running expenses of houses by proper heat insulation helps home owners to maintain payments on property, and by minimizing foreclosures helps to stabilize the financial structure of the country. In short, here is a situation where the interests of the individual and the Nation are identical and the greatest good for the greatest number is obtained without sacrifice to anyone.

Jan 1, 1941

By A. B. Hooker

The flame safety lamp with metal-gauze enclosure was invented by Sir Humphrey Davy more than a century ago, primarily for its safe light; however, it soon became the standard device for detecting the presence of methane in mine atmospheres. It still is the most widely used device for this purpose and is also the most practicable means of detecting deficiency of oxygen in coal mines. A permissible flame safety lamp is similar in all respects to one that, after a series of tests, has been approved by the Bureau of Mines as safe for use in gassy mines. However, safety depends largely upon the way lamps are maintained and used.

Jan 1, 1944

By F. Baerhold

Recycling of hydrochloric acid from the pickling of mild steel using pyrohydrolysis is a state-of-the-art technology. Recent developments have focused on the production of a high value iron oxide by-product, where the chemical purity and physical properties are the main issues. New processing routes, especially for TiO2 and Ni production, use leaching operations with hydrochloric acid. The feasibility of those processes depends on the availability of an economic and reliable process for the recovery of the acid. Depending on the level and type of impurities and the required specification of the by-product, pyrohydrolysis in a fluid bed or in a spray roast reactor can be the ideal solution. In stainless steel annealing and pickling lines, a mixture of nitric and hydrofluoric acids is used to remove the scale from the surface after heat treatment. Nitrate emissions from the pickling and the rinsing processes have to be avoided because of more stringent environmental regulations. An annealing and pickling line that is totally wastewater-free was developed, where not only the nitric/hydrofluoric acid but also the rinse water, is completely recycled. New developments to increase the HNO3-recovery rate and to obtain a metal oxide by-product that is easier to recycle are presented.

Jan 1, 2006

By Richard S. Kunter

Artech Recovery Systems, Inc has developed a low pressure and temperature? leach process called the "Cashman Process" to extract metals from arsenical flue dusts and residues and fix the arsenic in an environmentally stable form as ferric arsenate (scorodite). The process was pilot tested at Hazen Research in an integrated plant including continuous recycle from August 1989 to October 1989 during which several tons of flue dust were processed. Based on this pilot program, the process was deemed technically feasible and produced commercially salable products. Residues from this pilot program were subjected to a long-term stability test jointly designed by PTI environmental services and the USEPA. The process, its versatility, and the nature of the products is discussed in some detail.

Jan 1, 1992

By D. A. Fenton

The reliability of large diameter, high horsepower ball mill is paramount when large production and minimum downtime is required. The 17 ft. x 56 ft. double compartment ball mill at St. Lawrence Cement Company has the first gearless drive built in North America and has the world's largest hydrodynamic bearings currently built and running. The machine has seen three years operation and has met its specifications. The mill was designed by Aerofall Mills Limited and the gearless drive built and designed by the Canadian General Electric Company. This paper discusses the operation of the first North American installation of a gearless drive ball mill from the mechanical, electrical and process aspects.

Jan 1, 1977

By J. A. Organiscak

The U.S. Bureau of Mines investigated the relationship of bituminous coal seam parameters and the amount of airborne respirable dust generated at longwalls. Dust and coal samples were obtained from 20 longwalls operating in geographically representative coalfields throughout the United States. Statistical analyses of coal seam parameters and airborne respirable dust measurements indicate a likely causal relationship between seam type and respirable dust. Low-ash, high-volatile coal seams were associated with higher airborne respirable dust levels. A negative linear correlation (significant at the 95-pct confidence level) was observed between the seam's ash content and airborne respirable dust, explaining up to 18 pct (R2 = 0.18) of headgate dust level variation and up to 15 pct of tailgate dust level variation. Volatile matter was found to have a positive linear correlation with tailgate dust level, explaining 16 pct of the variation. Further data examination indicates that these relationships with dust are most likely nonlinear, because of improved R2 values over the linear correlations. However, a notable portion of longwall dust production is influenced by other operational parameters, so additional research under more controlled conditions is needed to determine the seam's causative functions.

Jan 1, 2010

By R. S. Nutter

The results of designing, constructing, and laboratory testing of a modular, distributed, microprocessor-based mine monitoring and control system are presented. A standard computer communications protocol (DDCMP) was utilized throughout the system. Tests were performed on the utilization of a high-level language for programming mine monitoring and control systems. Laboratory tests were run on a combined air velocity/methane sensor.

Jan 1, 1980

By V. R. Miller

The Bureau of Mines investigated methods for testing the tensile and sheer strength of cast specimens of bulk solder and of soldered joints in order to increase the strength and extend the useful temperature range of soft solders. A spread-area test for determining the wettability of solder on copper surfaces was developed. Mannitol was used as a flux in spread tests to control spreading and to avoid plating, etching, and other side effects of regular fluxes. Data on commercial and high-purity solders obtained by these methods show more consistency than those reported by others from similar tests.

Jan 1, 1967

By M. J. Gavin

Within the past three years numerous inquiries for information on oil shale have been received by the Bureau of Manes. These inquiries have been increasing to such an extent that it has seemed advisable to issue a short paper prior to the publication of a bulletin on the subject, giving a, general discussion of the subject and a comprehensive list of references, so that those interested in the details of obtaining oil from shale can find additional information without much difficulty. Some of those who desire information are interested only in a general discussion of the subject, or are not in a position to refer to books and' articles describing the industry. The material for this paper is largely derived from published information on oil shale. Much of the information is obtained-from the books and articles mentioned in the list of references, and has been compiled with the intent of furnishing information to those not interested in all the details.

Jan 1, 1921

Jan 1, 1998

By Thomas Palangio, Blessing Taiwo

Image-based fragmentation analysis is increasingly utilized in blasting operations to evaluate particle size distribution in a non-intrusive and efficient manner. However, the accuracy of optical granulometry systems can vary significantly with particle size. Higher precision is typically achieved for larger fragments, generally those greater than golf ball size when using drone-based orthomosaic analysis. In contrast, the detection and delineation of fine particles become less reliable due to constraints such as pixel resolution, particle overlap, and partial burial within the muck pile. This variability does not undermine the value of image analysis but rather highlights the need for a deeper understanding of its operational thresholds and the integration of complementary methods or calibration approaches to improve its reliability across the entire particle size distribution. Technologies such as WipFrag, originally developed in the 1980s, are designed to conduct in-situ fragmentation analysis within complex blast environments, where fines are often obscured by larger fragments. The challenge becomes more significant in blast rounds exhibiting wide gradation ranges and increased fines, particularly resulting from excessive energy concentration in high-pressure zones near the borehole. Previously, this issue was addressed through methods such as analytical correction, zoom-merge correction, and empirical calibration using Rosin-Rammler and Swebrec distribution models. However, these traditional empirical calibration approaches, particularly those tied to distribution functions like Rosin-Rammler have shown limitations, especially in accurately representing the fine region of the fragmentation curve. In contrast, the recently developed xP-fan model, which incorporates the relationship between powder factor and fragment size, introduces the fragmentation energy fan principle which Kuz-Ram model does not entail. This paper presents a study on the application of the novel xP-fan calibration to enhance the accuracy of optical granulometry systems. The findings demonstrate how xP-fan help calibrate the fine region of the PSD without deflecting the maximum size.

Jan 26, 2026

By Leslie D. Marrus

This project and final report represent an effort to collect, analyze, and verify reliability and performance data on currently available medium -to-high seam models of continuous miners being used in underground coal mining. The analysis determined availability, mean time and tons between failures, amounts of down time associated with various failures, labor and part costs required to correct failures, and various indices of maintainability. Machine performance and reliability are discussed relative to cumulative tons (machine age) produced and production rates (machine loading). It was determined that performance can be significantly improved given preventive maintenance programs that will increase machine availability.

Jan 1, 1976