Search Documents

By P. G. Barnard

The Bureau of Mines investigated the effects of various additions of rare-earth metals or rare-earth oxides on the mechanical properties of cast and wrought plain-carbon steels. Rare-earth metals, as misch metal, were added to medium-carbon steel in amounts to 0.70 weight-percent; rare-earth oxides, as a commercial mixture, were added in amounts to 1.50 weight-percent. The melting and casting of conditioned steels were done in a vacuum-induction furnace, to avoid formation of oxides from the melting atmosphere and to pro-vide better control over chemical composition. At room temperature, data for tensile strength, yield strength, elongation, and hardness of cast and wrought steels were obtained by standard testing equipment and procedures. Impact tests were conducted on as-cast steel specimens. The greatest amount of tensile ductility and impact strength was obtained in as-cast steel with 0.50 to 0.70 weight-percent misch metal additions. No significant improvement on mechanical properties was indicated in wrought steels containing rare-earth metal additions in the range from 0.10 to 0.70 weight-percent. In general, the rare-earth oxide additions up to 1.50 weight-percent had little effect on the tensile properties of steel in the cast, wrought and annealed, or wrought and normalized condition.

Jan 1, 1967

By Donald W. Mitchell

Certification tests for urethane-foam systems and techniques for apply-ing foam safely in mines are described. Fire hazard from foam exists if flame propagates beyond the ignition source or penetrates the foam. Foam that passes the certification tests can be applied on stoppings, continuous sections of ribs of relatively wide passageways (with no foam on the roof), short sections of roof such as overcasts, roof cavities, and intersections (with no foam on the ribs), and between buntons on one wall of a shaft. Foam on the ribs and adjoining roof presents a fire hazard. Stoppings covered with foam passing the certification tests are resistant to penetration of heat, flame, and smoke than similar stopping without foam. Flame propagation can be arrested by water sprays. Spontaneous ignition of foam can be prevented.

Jan 1, 1966

This appendix contains the list of equipment selected for the capitol cost estimate, with the respective quotations from their vendors/manufacturers. A vendor response report along with a separate equipment and motor list has been included in the first part of this appendix.

Jan 1, 1979

By Raymond W. Hiteshue, Sam Friedman, Paul Dobransky, Robert Madden

A hvab coal was carbonized in a closed system at 600 ° C and 40 to 1 , 200 psig to produce a high- Btu gas and char . By retaining the volatiles within the system, it was possible to virtually eliminate production of tars and oils . Depending on pressure and residence time , yields of combustible gases (72 to 92 percent methane ) amounted to 4,000 to 6,000 cubic feet per ton of maf coal and gross heating values of these gases varied from 830 to 960 Btu per cubic foot . Yields of char (maf ) were about 1,600 pounds per ton of maf coal . Increased residence time favored production of gases but reduced their heating values , whereas increase in pressure resulted in somewhat higher heating values and lower production . Similar effects were observed from the carbonization of a low- temperature tar . If these results could be translated to an economical carbonization process for producing high- Btu gas from coal , the demand for coal could be expanded by 40 to 50 million tons per year . Because of large yields of char , a process of this type would obviously have to be integrated with coal - fired power plants . Fortunately , operations could be conducted at essentially atmospheric pressure as product gas under this condition can be obtained in satisfactory yields and with good quality .

Jan 1, 1964

By W. G. Millar

Until a fire occurs, insurance and prevention work are often looked on as unavoidable necessities, but as insurance is back of all business credit, it is essential to know that in case of damage money will be available to cover the loss; while the interruption of production, often caused by a fire, brings home the realization that if prevention work avoids such an interruption, it is well worth while. Fire insurance is a legal contract guaranteeing the payment of large amounts to an owner, but it is possible there is no other important contract that receives so little consideration. Although previously carried on elsewhere, it is only of recent years that insurance engineering has been actively followed up in Canada, with inspections of an owner's property carried out for his benefit. Now inspections of this kind are made, advice on fire prevention and protection work ?is available, reports with recommendations with regard to the above are furnished periodically, and with this method applied the owner receives the broadest possible cover and security at the lowest cost. Rates are set by the underwriters by rating schedules which charge for defects in a building and allow credits for protection and other favourable features . These schedules are based on the past record of loss of mining properties as a class, so that a fire in another mining property indirectly affects you, but the amount paid is reduced in proportion as your property is improved. The writer feels, from personal experience, that there is no industry where fire prevention receives more attention than the mining industry, and it is a pleasure to advise that, due to this co-operation, some reduction in the basis rates for mining risks is now being made by the underwriters.

Jan 1, 1928

By T. W. Turk

In May 1984, Davy McKee Corporation was awarded a contract for engineering design, procurement assistance, project management and startup services for two gold recovery plants? in the People's, Republic of China (PRC). The basic design of these two projects was to be accomplished by a combined effort of the Chinese and Davy McKee Corporation (DMC). The, design goals were to provide a state-of-the art plant while maintaining Chinese standards and design practices whenever possible. Chinese-manufactured equipment was to be used as much as possible. This paper discusses the project organization and procedures developed to accomplish the design goals, the process selection and design, and the selection and procurement of equipment outside of the PRC. Design development for grinding, leaching and carbon adsorption, and gold recovery are discussed in detail. The major goal of process selection and design was to provide common criteria for both plants. Equipment .sizing and selection was identical for carbon-in-leach adsorption, gold recovery, acid washing, and carboo regeneration for both plants. Of special importance is the design of the wastewater treatment system. Due to the cl0se proximity of a major population area, slurry discharging from these mines must be treated to meet drinking water standards. The process development and design of this system is also discussed in detail.

Jan 1, 1989

By K. G. Baxter, D. G. Dixon

The Sepon process plant utilises an autoclave to oxidize a flotation concentrate containing pyrite, residual copper minerals, and sulphur. The concentrate is produced from the residue of a preceding atmospheric copper leaching circuit. The function of the autoclave is to provide iron and acid for that atmospheric copper leaching circuit. The key issues in the operation of the autoclave are to maximise the production of acid and ferric ions and to avoid scaling issues related to sulphur balling in the autoclave. Scale control in the autoclave was examined using various dispersants and residue recycle without success. Operation of the autoclave at high temperature and high acidity addressed the scale issue through rapid oxidation of the sulphur and produced a ferric sulphate precipitate in the residue that could be re-leached to provide ferric iron. This paper presents the development steps followed, through batch and continuous piloting that resulted in an autoclave circuit design that addressed the above process requirements. Following definition of the process design basis, modelling of the autoclave operation was carried out to assist with engineering design. The model included thermodynamics and kinetics of oxidation of pyrite, elemental sulphur and covellite and also considered gas/liquid mixing, oxygen solubility as a function of temperature and solution composition, ferrous to ferric oxidation, gangue reactions with acid and precipitation/re-dissolution of basic ferric sulphate and alunite.

Jan 1, 2004

By T. Shibasaki, S. Kamio, K. Kanamori

"Mitsubishi Process has been proven through fifteen years operation to be highly productive, cost efficient and easy to abate environmental requirements. However, in order the process to remain competitive from now on, it should also be adaptable to a variety of varying conditions. Various test works have been conducted from such a stand point of view and some of the new concepts have been implemented to the actual operation.The paper discusses the adaptability of the process to the change of concentrate grade with respect to copper and also impurities, acceptability of the secondary materials and the potential to increase unit capacity. IntroductionThe first commercial plant of Mitsubishi Process with 48,000 mt copper annual capacity started its operation at Naoshima Smelter of Mitsubishi Metal Corporation in 1974, and the second plant with 65,000 st annual capacity started in 1981, at Kidd Smelter, Timmins, Ontario, now Kidd Creek Division of Falconbridge Limited 2. These plants have increased their capacities to 90,000 mtpa respectively by adding oxygen and acid plant capacities while maintaining the original furnace design uncharged. Thereby both smelters have established more cost efficient operations. (3), (4)Mitsubishi Process applies so-called multi-furnace continuous system. Figure 1 shows conceptual flowsheet. Backgrounds that required and justified the development of such system are as follows:"

Jan 1, 1988

By Ju-hyung Ha

New automated curing system for mass concrete has been developed to improve the quality of concrete structure and to save construction time and cost. The principle of this system is the automated water circulation system of heated curing water. Applied curing water on the surface of mass concrete keeps the temperature difference between center and surface of the structure below the threshold of specification. Mock-up test and field application have been conducted to investigate the performance of this system. In the results, new automated curing system reduced the chance of thermal crack occurrence and improved quality of the concrete structure as well.

Aug 1, 2013

By W. A. Cole

This report covers the preliminary phase of an investigation of some clays and shales and other materials in North and South Dakota to determine the feasibility of lightweight -aggregate manufacture in the two States. The background of the light - weight -aggregate industry, on a national basis, and results of preliminary laboratory testing of samples of North and South Dakota clays and shales from various localities are presented herein. The countrywide search for lightweight aggregates was necessitated toward the end of the 19th century by the change in building design from thick, heavy, load- bearing walls to a framework of structural steel .beams and columns with thin walls, followed shortly by the use of reinforced concrete and structural concrete as materials for the load-supporting frame. Ordinary concrete, with sand and gravel aggregate, weighs about 150 pounds to the cubic foot. A lighter concrete was needed to relieve the dead load and make it possible to construct higher buildings or add stories to existing buildings.

Jan 1, 1954

By W. P. Haynes, J. W. Mulvihill, G. B. Taylor, S. Katell

Capital and operating costs have been estimated for separating methane and hydrogen in gas - separating plants designed to produce 90 million scf per day of product gas containing a minimum of 90 percent methane . After a preliminary literature review of various separation techniques , three different processes --moving - bed adsorption using active carbon , oil absorption , and liquefaction -- were chosen for the cost estimates . Three different methane feed gas concentrations , 5 , 20 , and 50 percent ( cases 1 , 2 , and 3 , respectively ) , were chosen as representative methane concentrations for the separation estimates . Capital and operating costs were lowest for the moving - bed adsorption process in all three cases investigated . Operating costs declined from $ 0.24 to $ 0.06 per 1,000 cu ft of product gas , and capital costs declined from $47,490,800 to $7,411,200 as the percentage of methane in the feed gas increased from 5 to 50 percent .

Jan 1, 1964

By D. E. G. Maschmeyer

The operation of the pilot plant for the S-C Copper Process during 1976 has provided the basic data for the design of a commercial-scale plant. This paper introduces the commercial aspects of the S-C Copper Process through the presentation of a process flow diagram, a schematic flow diagram and basic design parameters for 75,000 tonnes per year (tpy) copper rod production from chalcopyrite concentrate. Basic operating requirements are outlined and a preliminary estimate of operating and capital costs for a Western Canadian location are summarized. The results have been compared with a modern smelter/electrorefinery to highlight the advantages and disadvantages of these two alternatives and to show why the new S-C Copper Process technology should be of interest to the copper industry.

Jan 1, 1978

By O. Guven, I. Karaagaçlioglu, O. Ozdemir, M. Çelik

In this study, the effect of morphological properties such as shape factors and roughness of the glass beads on their flotation efficiency were determined using image analysis and profilometer methods. There is a considerable correlation between the shape factors, surface roughness and flotation behavior of the glass sample. These results indicate that as the particle shape is away from roundness and smoothness, it acquires more hydrophobicity.

Jan 1, 2014

By S. A. Vazhnov, A. G. Kalimov, A. A. Potienko

In this paper we describe a mathematical model of the magnetic field and magnetohydrodynamic processes simulation in aluminum reduction cells developed in St. Petersburg State Polytechnic University, Russia. The model includes: (a) calculation of the currents in the busbar system and inside the aluminum cell construction elements including cathode and anode structures, aluminum and electrolyte layers; (b) magnetic field simulation using the integral equation method; ( c) investigation of the magnetohydrodynamic characteristics on the basis of a shallow-water approach. The developed model was used to investigate operational characteristics of the different industrial aluminum cells. Calculated magnetic field distributions and MHD stability parameters were compared with the available experimental information; the comparison demonstrated a reasonably good agreement.

Jan 1, 2006

For the past 40 years, underground trucking using diesel powered or electric wheel driven vehicles, either conversions of surface trucks, or purpose built, has been the preferred means of ore and waste transport in underground mining. The relatively low capital cost, flexibility and requirement for minimal infrastructure means that trucking systems are selected in the early stages of a mining operation. An increase in the carrying capacity of trucking systems with dimensions to operate within existing development excavations is the solution to long term ore and waste underground haulage systems using trucks. The next generation of underground trucks will be low profile articulated trucks with carrying capacities up to 60 t.

Jan 1, 1998

Engineering programs usually do not provide sufficient opportunities for students to develop written communication skills. The responsibility for developing those skills is frequently delegated to the humanities faculty, who in a single technical writing course are supposed to transform engineering students into proficient communicators. A general template which was developed for report writing in our senior level capstone design courses is discussed. Students have improved their writing skills by using the template. The writing assignments have provided the students the opportunity to write and revise more technical reports that communicate their design.

Jan 1, 1995

By The SME Sustainable Development Committee

The evolution of sustainable development in mining is recognized as a key contributor to sustainable development (SD), which is defined as the ability of current generations to meet their needs without compromising the ability of future generations to meet their own needs (Brundtland, 1987). This includes, in equal parts, social, economic and environmental impacts ? triple bottom line (Munashinge and Shearer, 1995). Alternately, sustainability has been defined in relation to social, natural, human, physical and financial capital. Our way of life relies significantly on the materials provided by mining, while mining activity affects the triple bottom-line or the five capitals. The mining community and its professionals have come to realize the importance of engaging all stakeholders in the discussion on sustainability. SME, as the leading professional mining organization, has been involved in these discussions. The society has various initiatives in sustainable development for members and stakeholders. The objective of this article is to: provide historical context for current trends in mining and SD and share SME sustainability initiatives ? their goals and rationales ? with the broader mining community. This article is timely because the past year saw two landmark forums on sustainable development: Rio+20 ? the 20th meeting of the United Nations Conference on Sustainable Development, and MMSD +10, the Mining, Minerals and Sustainable Development project 10 years on. Furthermore, this year marks the 10th anniversary of the Milos Declaration on the minerals professional?s responsibilities in achieving sustainable development, forums in which SME was involved.

May 1, 2013

By Y. Y. Zhou

This paper introduces the application of CRIMM high-gradient magnetic separator in refinement of feldspar powders as well as the supporting technical outfits needed by the refining process with the high-gradient magnetic separator as main equipment. It could reduce the content of Fe2O3 to 0.03% with a deferrization rate of 85.88% from the feldspar raw ore containing 0.17% Fe2O3by using the above refining technology, producing an ultrapure feldspar product.

Jan 1, 2014

By Akira Yoshida

Este trabalho apresenta o sistema de Nível 2 recentemente implementado nos Altos Fornos da TKCSA cujos principais objetivos foram: substituir o sistema antigo com problemas de instabilidade e falta de flexibilidade; auxiliar Operação e especialistas da Unidade Técnica fornecendo informações elaboradas a partir de dados obtidos nos demais sistemas (Nível 1 e Laboratório); enviar set-point ao Nível 1; enviar dados de consumo e produção ao sistema MES; etc. Com a implementação foi possível reduzir o tempo gasto pelos especialistas nas atividades de compilação de dados em planilhas, padronizar a forma de tratamento dos dados, bem como, elevar a confiabilidade das informações pela eliminação de erro de digitação. O sistema tem operado com elevada estabilidade e disponibilidade, atendendo perfeitamente o que foi proposto, de modo que a TKCSA planeja estender para demais plantas da área de Redução.

Aug 16, 2017

By Gabriel R. Royo

This paper will cover a back up roll bearing technological upgrade, being implemented at the TERNIUM SIDERAR Hot Strip Mill (HSM), in San Nicolas, Buenos Aires, Argentina. This change was motivated by increased operating loads, which caused the original bearings to be outside the designed bearing rating. The problems were first identified by bearing seizures in some stands, and later followed by cracks forming in the back up roll neck areas due to fatigue and overload. MORGOIL engineers worked together with TERNIUM SIDERAR engineers in analysing the problem and to upgrade the mill with the newest and most economical technology. The upgrade consisted of changing the bearings to the latest generation MORGOIL bearing: the KLX, which within the same space, increases bearing capacity around 25%. This was accomplished re-utilizing all chocks. The new bearing allowed for a re-design of the geometry of the back up roll neck, making it much stiffer than the original design, and eliminating fatigue failures. In addition, an upgrade to hydraulic mounting and dismounting using the MORGOIL® HB lock was also implemented, as well as changing to the newest MORGOIL® HD seals. With the MORGOIL® KLX® upgrade, TERNIUM SIDERAR HSM increased load capacity, allowing them to roll products that were not even considered decades ago. Both older oil film bearings and roller bearing mills have been successfully upgraded while reusing existing chocks and in many cases rolls. Solutions are customized to the customer’s equipment and goals.

Oct 30, 2017