Search Documents

By Parry. V. F., John B. Goodman

"INTRODUCTION The Denver region coal field, covering an area of approximately 7,640 square miles, extends from the Wyoming State line to the middle of El Paso County, Colo. The coal in this region is subbituminous in rank. Much of it is used as domestic fuel. During the last decade the production of coal in this field has remained fairly constant at an average of 2,600,000 tons per year. This production has come from 50 to 60 mines, 88 to 90 percent of the production being from the section of the field north of Denver.According to the Standard Specifications for Classification of Coal by Bank of the American Society for Testing Materials 4/ the coals in this region are classified in the Subbituminous B and C group. On the as—mined basis, they contain about 22 percent moisture and average 9,600 B.t.u. per pound. They are noncoking and slack to a variable extent when exposed to the weather. This is characteristic of subbituminous coals."

Aug 1, 1939

By L. D. Schmidt, W. C. Schroeder, A. C. Fieldner

"INTRODUCTION The highly mechanized character of modern warfare makes steel the most vital raw material. The shortage of steel scrap in the United States is forcing the use of increased quantities of pig iron in steel manufacture, so that the rate of pig-iron output will continue to be the controlling factor in steel production. 5/ At the same time, the construction of new blast furnaces is limited both by time and the amount of strategic material available. Under such circumstances, every effort must be made to attain and then maintain maximum pig-iron output from the equipment now in use.When forcing a blast furnace to the ultimate in production the highest standards for quality and uniformity of the coke must be maintained. In view of these facts, the Bureau of Mines, in cooperation with the Office of the Solid Fuels Coordinator for War, is surveying the coke industry to study the various steps in producing coke of higher quality and greater uniformity. 6/ The engineers conducting the survey are visiting key men in coke-oven and blast-furnace organizations to determine, first, the major and most common problems in coke production and use; and, second, the best and quickest method for solving them. Various operators have made good progress in solving individual problems, and a Nation-wide exchange of information among them will make possible widespread adoption of the best practices. It is the purpose, of the survey and reports such as this preliminary one to facilitate such exchange of information. As an outgrowth of the survey, it was soon revealed that many operators could be helped by cooperation with various Government agencies, particularly to procure suitable coals, minor additions to equipment facilities, and tests on certain properties of coal or coke, or specific advice concerning the operation of various types of equipment. The machinery and organization necessary for securing this cooperation have been set up as a part of this work."

May 1, 1943

By G. K. Herzog

THE problems relating to the construction and use o{ mining equipment are basically the same as those pertaining to equipment in other industries. It is true that much mining equipment is subjected to an unusually severe combination of shock, high stresses, abrasive wear, and corrosive ? conditions, but in other industries, also, equipment must operate under similar adverse conditions, so that their experiences may readily be applied to the problems of the mining industry. Steel and iron are for obvious reasons the most suitable materials for the construction of the greater part of the equipment used in the mining industry. For a large percentage of uses, the ordinary plain carbon-steels and ordinary or unalloyed cast-iron are, and probably will continue to be for a long rime, entirely satisfactory materials. There are, however, many. conditions which cannot be satisfactorily taken care of by these materials, and alloy steels and irons must be used where the greatest possible economy is desired. In general, alloy steels and irons are used where it is necessary or economically desirable to use materials possessing properties superior to plain carbon-steel or ordinary cast-irons, such as: (a) better strength (b) better wear resistance (c) better corrosion resistance (d) better resistance to high temperatures (e) better resistance to low temperatures or combinations of two or more of these advantages. There are also conditions where materials having other special properties are required, such as, for example, certain magnetic or electrical properties for electrical machinery; but in the great majority of cases, one or more of the five advantages listed are the most desired.

Jan 1, 1938

By Angus D. Campbell

Introduction In the Twentieth Annual Report of the Mcintyre Porcupine Mines, Limited, for the year ending March 31st, 1932, the General Manager, Mr. R. J. Ennis, said: "During the period under review, the plans outlined in last year's report have been completed, and all operations have been centralized in the new plant adjacent to No. 11 shaft. The new mill went into operation on May 27th and attained its rated capacity of 2,000 tons per day on November 15th. The new shops, warehouse, change-house, and general offices were occupied on December 1st, consummating the change from the old to the new plant ... "Silicosis is now definitely recognized as an industrial disease, and progresses rapidly when associated with tuberculosis. In an effort to combat its prevalence and progress, the new change-house was designed to build up the men's resistance to this and other forms of disease. It provides for a complete change from underground to street clothing, with a shower bath and solarium treatment in the interval. 'Unfortunately, in almost every goldmine, a very small percentage of the work-men are not adverse to taking some of the high-grade ore for their own purpose. This, in turn, tends to cast suspicion upon the honourable as well as the dishonorable employees. The new change-house routine discourages this practice and eliminates unjust suspicion, to the satisfaction of all concerned with the Company's operations".

Jan 1, 1933

By David E. Nicholson

The Bureau of Mines has constructed a special compression chamber for developing stress-strain relationships of mine backfill and simulating the high compressive ground pressures encountered in underground mines. A one-dimensional, or Earth-Pressure-at-Rest model is proposed for backfills subjected to these pressures. Results of the compression tests performed in the chamber indicate that reliable stress-strain relationships can be developed from these tests. The primary objective of the test series was to evaluate the effectiveness of compaction of common backfills in retarding ground closure. Analysis of the stress-strain data shows an eightfold reduction in relative strain in optimum well-graded, compacted backfills over poorly graded, loose backfill material. Analysis of the one-dimensional compression test data also indicates a significant retardation of transmitted stress in dense compacted samples of backfill and natural sands. Although not fully understood, a deformation mechanism is thought to occur at the intergranular contacts in cyclic fashion causing frictional heat loss and a reduction in transmitted stresses in the densely packed materials. The experimental values of transmitted stress are compared with theoretical values of effective stress calculated from the one-dimensional compression relationships developed by Hendron (4).3 These experimental values of transmitted stress compare very closely with the theoretical values of effective stress.

Jan 1, 1968

By O. G. Paasche, Yuan-Shou Shen

THERE is a disagreement among the various authors about the exact manner of transformation of ZrCr2. Rostokerl and others2 stated that ZrCr2 had a C-14 (MgZn2) type of structure below 1000°C and a C-15 (MgCu2) type of structure at temperatures above 1000°C. Alisova3 and others4 reached the opposite conclusion and stated that the transformation temperature is close to the melting point of ZrCr2. A literature survey shows that various investigators3'= who homogenized the specimens at a temperature higher than 1000°C have concluded that ZrCr2 had the C-15 structure at room temperature. Meanwhile, Jordan et al.4 reached similar conclusions without annealing the specimen. Other investigators1,2,6,7 who X-rayed the specimens in the as-cast condition without annealing reached different conclusions. The investigation reported herein was conducted with the aim of exploring the exact manner of transformation of ZrCr2 by various heat treatment tests. The alloys for this examination were prepared from iodide-reduced zirconium crystal bars, 99.9 pct purity, and electrolytic chromium, 99.9 pct purity. They were melted in a nonconsumable electrode arc furnace with water-cooled copper crucible in a helium atmosphere. The melting loss of each alloy was less than 1.5 pct by weight. Chemical analysis of a randomly selected specimen indicated that there was a very close agreement between calculated and analyzed compositions. Before being heat-treated each specimen was encapsulated in a vycor or quartz tube inside which an argon atmosphere was maintained at a pressure of lower than 1 atm. In determining the crystal structure of each specimen with a Debye-Scherrer camera, the standard procedure8 for X-ray quality analysis (Hanawalt method) was followed. The different series of heat treatment tests in this investigation are tabulated in Tables I and 11. The tests in Series I, specimens from 1-1 to 1-9, which were similar to Rostoker's experiment1 indicated that the transformation temperature seemed to fall between 870° and 900°C and that the crystal structure of ZrCr2 at lower temperature seemed to be of the C-14 type. However, once the compound is transformed to C-15 type, it is impossible to reverse the transformation back to the C-14 type by first heating the specimen above 900°C and then annealing it slowly below 900°C as shown in Experiments II-1 to II-3. Thus, it appears that the specimen of ZrCr2 will transform from C-14 to C-15 structure when heated above 900°C but will not transform from C-15 to C-14 when annealed slowly passing 900° C even after the extremely slow cooling process such as indicated in the experiment of Specimen II-3. As a valid transformation temperature is a temperature at which the transformation is reversible, therefore the temperature 900°C (or other temperature close to 900°C) is not the transformation temperature for ZrCr2 and the C-14 structure is not the stable structure of ZrCr2 at lower temperatures. The C-14 structure is retained at room temperature because the transformation to C-15 structure is very sluggish and the fast cooling after melting does not allow enough time for the transformation to take place. Additional energy is required to alter the metastable condition of the C-14 structure. The sluggishness of this transformation was again demonstrated through another series of experiments. Four specimens with C-14 structure were taken. Then they were annealed at 900°C but each specimen was soaked for a different period of time, Table 11. X-ray diffraction patterns of this group indicated that the C-14 structure gradually disappeared as the soaking period was lengthened. The figures listed under the column "C-14 Structure, pct" were estimated from the intensity of the d = 2.330 line of the diffraction pattern corresponding to the structure. Notice that the intensity of this line became weaker for longer soaking periods. To determine the transformation temperature of ZrCr2, specimens with C-14 structure (as-cast condition) were annealed at 1300°, 1400°, 1500°, 1550°, and 1600°C, respectively. A final specimen was first heat-treated to 1500°C in order to transform it to C-15 structure, then heat-treated at 1600°C again. From the X-ray analyses of this series of tests, Specimen Nos. III-1 to III-6, it is evident that a transition from C-15 structure at lower temperatures to the C-14 structure occurs at some temperature between 1550° and 1600°C.

Jan 1, 1969

By X. G. Liu

Bentonite is an excellent sealant mineral material because of its desirable swelling and self-healing characteristics, low permeability, sorptive qualities, and longevity in nature. A new type of water-swelling building sealant made from bentonite was studied in this paper. The building sealant is prepared by Na-base bentonite, vaseline and paraffin wax under different mass fraction of bentonite (which is 60%,65%,70% respectively). Under unrestricted state, some properties of samples were investigated. The volume expansion ratio at 24 h is 211%, 222%, 256% , and permeability coefficient is 2.86×10-8 cm/s, 4.15×10-8 cm/s and 4.78×10-8 cm/s respectively; low temperature flexibility of the sample (bentonite quality is 65%, 70% respectively) is good, and it does not flow heated for 2 h under 80?. The results of XRD and SEM indicate that bentonite is coated preferably by vaseline, and the spacing of layers of bentonite do not changed. The sample can keep full water swelling ability, and has good molding process. The test results prove that the properties of samples may reach the standard of building sealant.

Jan 1, 2014

By John Nagy, Henry G. Dorsett, Murray Jacobson

Laboratory studies show that ignition of a dispersed combustible dust in an open vessel may be prevented by adequate inerting . Factors affecting the inerting requirements are -- dust concentration , spark energy , ignition temperature , composition of the substances used for inerting , fineness of dust and type of combustible . The oxygen concentration of the atmosphere and in some instances the proportion of admixed inert powder and moisture required to prevent ignition are given for 367 dust samples . Variations in inerting requirements with strength of igniting source are discussed .

Jan 1, 1964

By John B. Goodman

A LOW-TEMPERATURE carbonization assay test is described, and factual data derived from this test are presented. The test procedure outlined in this report incorporates a mild-steel retort of improved design, an accurately controlled method of heating, and a complete collection and condensation system for the solid, liquid, and gaseous products of carbonization. The test described establishes, under closely controlled conditions, the relationship of temperature to yields of products on carbonization. Noncoking or weakly coking coals and other carbonaceous material are particularly amenable to testing by the assay. Mass balances of 100 percent± 0.3 are obtainable by this test. It is believed that the efficiency of the test and the accuracy of the type data obtained have been materially increased.

Jan 1, 1953

By F. G. Schwartz

The Bureau of Mines developed a rapid and precise method for predicting storage stability of motor gasolines. This method resulted from the investigation of many analytical techniques as well as a study of fuel composition and fuel component gum-forming mechanisms. The first section of this bulletin discusses the development of the prediction test through its several phases, including revision of the standard 110° F storage test; attempts to develop a modification of the ASTM D525 induction bomb test; and the ultimate abandonment of this procedure with the adoption of the 16-hour oven test that was both precise and rapid. The second section comprises a discussion of further studies of fuel com- position, including the reactivity of certain sulfur compounds and hydrocarbons to form gum. The compositions of various gums and inorganic deposits are reported in terms of elemental analysis and spectroscopic examinations. The reactions of tetraethyllead with selected hydrocarbons are also reported.

Jan 1, 1972

By James P. Bennett

The Bureau of Mines is investigating the acid resistance of ceramic materials to identify construction materials for emerging technology in chemical and metallurgical processes. Eight commercial ceramic materials, were evaluated: two red shale, two fireclay, one silicon carbide, one silica, one carbon, and one high-alumina. Samples were exposed to 10 wt pct H2S04 at 50° C and 10, 30, 50, 70, and 90 wt pct H2S04 at 90° C for time periods of 110 days. Statistically significant changes in cold crushing strength were observed in the silicon carbide and car-bon materials. Weight changes and the leach rate of Al, Ca. Fe. K, Mg, Na. Si, and Ti were also monitored. The most severe corrosion conditions were at 90° C and 30 to 50 wt pct H2S04 for the acidproof and at 10 wt pct H2S04 for the acid-resistant materials. The silica and the high-alumina materials were the most acid-resistant, followed by the higher density red shale and fireclay.

Jan 1, 1986

By J. F. McIlwain

Cobalt-base hardfacing alloys used for wear resistance consist almost entirely of metals largely imported into the United States. As part of an overall research program to help alleviate this foreign dependency, the Bureau of Mines has been investigating an iron-base alloy system as a potential replacement for cobalt-base alloys for some uses. To ascertain the melting ranges, thermal analyses were made of cast heats of alloys containing, in weight percent, 59-61 Fe, 16-19 Cr, 8-9 Ni, 1 Mn, 1 W, 1 Mo, 0.5 Cb, 0.6 Si, 0.3 C, and 0-12 stoichiometric TiB2. Powder alloys within this range of composition, prepared by mechanical alloying, were sized and applied to mild steel test coupons by nontrans-ferred-arc plasma spraying. The resulting thin coatings were >95 pet dense, with bond strengths of 35 MPa and hardness of 400 to 840 DPH. Abrasive and adhesive wear test data were compared to those of a plasma-sprayed cobalt-base alloy. A range of boride contents resulting in most promising properties was determined for further research.

Jan 1, 1985

By H. A. Baumann

Experimental data are presented showing the influence of size consist and firing rate upon the performance of bituminous coal-fired, single-retort, industrial underfeed stokers. Size segregation, degradation, and distributor data are also included. The conclusion is reached that size consist of the fuel as fired, is a critical factor in its performance on this class of equipment.

Jan 1, 1950

By Richard H. Otto

Three longwall mining methods practiced in foreign countries are described that have potential for increasing underground recovery and productivity in thick coalbeds of the Western United States. The methods are multislice long-walling, longwall caving, and high-face longwalling. Foreign practice and possible application in the United States are discussed.

Jan 1, 1979

By R. L. Grant

[Detonators are used to explode permissible explosives, dynamites, or other high explosives. This explosion or detonation is brought about by the energy which is liberated as a combination of concussion and heat when the detonator is fired. In Other words; "The detonator is the key which unlocks the energy of a high explosive" (8)4. Being sensitive and latently dangerous, detonators must meet two primary requirements: They must be safe to handle and must detonate when desired, thereby imparting detonation to the explosive charge.]

Jan 1, 1941

By C Slaughter, J C. Tien

Commonly held ideas about effective training have long emphasised the importance of realism. Realistic training builds better experience among the trainees and a better perspective on the training material, making training more effective. While great strides have been made in this realm for mine safety and mine rescue training there are still areas that can be improved. One possible area is the expanded use of a mine fire simulation program where the migration of gases and smoke can be realistically displayed in an emergency, and outcomes varied as different conditions are being simulated. The use of mine fire simulation software potentially allows for the creation of more realistic scenarios in that smoke advance rates can be measured and recreated in evacuation scenarios, or that gas readings in mine rescue training can be dynamically and realistically changed to show the effect that time has on the fire scenario.CITATION:Slaughter, C and Tien, J C, 2015. The potential use of mine fire simulation software as an enhancement for mine safety and mine rescue training, in Proceedings The Australian Mine Ventilation Conference, pp 285–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

"5.1. IntroductionThe sample preparation requirements for bulk analyses of platinum-group elements (PGE) are different from the requirements for ore microscopy and in-situ analyses. It is necessary that the initial sample collection results in as representative a sample as possible for both types of analyses. Ingamells (1980) believes, however, that sampling is always imperfect and that there is no such thing as a truly representative sample. Once collected, the usual low content and irregularly dispersed nature of the PGE require that samples for bulk analyses be made as uniform as possible, whereas in samples for ore microscopy and in-situ analyses the PGE must be concentrated. Because of the generally high specific gravity of platinum-group minerals (PGM), certain precautions must be taken, such as mixing the sample material in the bags prior to opening.5.2. Preparation forBulk Analytical MethodsThe principal factors that determine the size of the sample required for a bulk analysis are grade, heterogeneity and grainsize. Initially, the grade and sample heterogeneity can only be estimated and a sampling methodology is developed with experience. It is essential at all times, however, that the assayers have information about the source of the sample and the purpose for the analysis. Information on the grain-size, which can only be obtained through mineralogical analysis, is also very important for PGE analyses, but, unfortunately, is often ignored.5.2.1. Samples fromUnconsolidated DepositsConcentrations of PGE may occur in eluvial deposits as well as in a large variety of alluvial deposits, including those of fluvial and glaciofluvial origin. These deposits are often difficult to map and sampling is further complicated by the wide range, from sand-size to boulders, of the non-POE-bearing constituents, and by the irregular distribution and shape of the ""pay streaks"". PGE concentrations in unconsolidated deposits are largely composed of resistant Pt-Fe and Os-Ir-Ru alloys (cf. Cabri and Harris, 1975 and Raicevic and Cabri, 1976), thus making comminution to the usual-150 to -200 mesh somewhat unreliable, due to the malleability of these alloys."

Jan 1, 1979

By Dale S. Preece, Ruilin Yang

"Air-decks are often employed for presplitting along the final highwall of a blast and are sometimes also included at the bottom or in the middle of explosive columns in the production portion of a blast. Shock wave physics is an important part of air-deck behavior since the bulk explosives in the column impart a shock into the air-deck where the air shock then passes through the air-deck at a rapidlyattenuating velocity. Through both high-fidelity modeling and shock physics theory it is shown that theresulting pressure in the air-deck is two orders of magnitude less than the detonation pressure of theexplosive."

Jan 1, 2017

By Thomas A. Gray

The Dolph Mine fire site is located in Lackawanna County, PA, approximately three miles northeast of the city of Scranton. The fire was burning in both coal refuse (culm) and underground anthracite mine workings. It was reportedly begun by rubbish burning on top of a culm bank. A site investigation was completed in 2006 to define the extent of the fire and to recommend fire control measures. A cut off trench was selected as the principal control method. Plans and specifications were prepared in late 2006. The project was bid and a contractor selected in early 2007. The trench construction was completed in 2007. This paper describes the investigation and selection of the fire control method and discusses the trench construction.

Jan 1, 2009

By C. A. Young

Previous experimental results have shown that an increase in temperature and/or oxygen concentration leads to an increase in the hydrophobicity of fluorite (CaF2) with adsorbed oleate. Subsequently, ex-situ Fourier transform infrared (FT-IR) transmission studies suggested that this increase in hydrophobicity was the result of double-bond reactions between adjacent oleate species adsorbed at the fluorite surface. Now an in-situ FT-IR study on single crystals of fluorite has been used to monitor this phenomenon using internal reflection spectroscopy (IRS) with the crystals serving as reactive internal reflection elements. The double-bond reaction has been correlated with in-situ adsorption density measurements. These results demonstrate that only the first chemisorbed oleate layer undergoes the double-bond reaction at an appreciable rate. However, multilayers of precipitated calcium oleate in the case of fluorite appear to react minimally even for oxygen saturated solutions at elevated temperatures.

Jan 1, 1991