Search Documents

By H. R. Shell

Of three known compounds in the ternary system K20 - PbO - SiO2, one having the composition K2Pb4Si8021 crystallizes into a structure with asbestiform properties. This compound, whose silicon-oxygen ratio is between that of the layer silicates (for example, mica) and the double-chain amphiboles, crystallizes in the tetragonal system. It malts, apparently congruently, at 779° C. The fiberized product prepared from crystals is fluffy and closely resembles natural asbestos in appearance, but is more brittle and has less strength. However, potassium-lead silicate may be separated into fibers with a uniform diameter of 200-300 A.U., and the fibers show with the electron microscope the s criteria that have been interpreted as indicating a hollow tube structure in chrysotile asbestos. Since very few inorganic crystalline compounds have such a structure, the material has unusual scientific interest. Microcrystalline potassium-lead silicate was rapidly and completely formed when powdered glass of the same composition was heated to 650° - 700° C, but macrocrystals grew only slowly from the viscous massive glass. Maximum growth rate was 0.12mm. per hour at 700° C.

Jan 1, 1957

By A. C. Stevenson

"There are many critical application issues that affect all AC drives, but there are several that are absolutely mandatory for pulse width modulated (PWM) AC drives. If these rules are not followed, the drive system will have insulation, bearing EMI or noise problems. Pulse Width Output VoltageFigure 1 shows the output current of a typical pulse width modulated (PWM) drive. This is, of course, not a clean sine wave thus will have a lot of very significant harmonics. In fact, the harmonic spectrum is directly related to multiples of the carrier switching frequency plus side bands related to the basic output frequency. A typical spectrum for a PWM source bridge switching at 5 kHz is shown in Figure 2. Notice that the spectrum has multiples of the 5 kHz switching frequency and the number of side bands gets larger as the harmonic number increases.IGBT Switching TransientsWhenever we have PWM inverter switching, voltage transients are formed that propagate (usually at about half the speed of light) down the power cables to the motor just like in a radio frequency transmission line. If we do not terminate these transmission lines (motor cables) properly, the voltage pulses will be reflected when they reach the motor end and will be transiently increased up to twice their original amplitude.This transient voltage rise, shown in Figure 3, is important for three reasons:1. Insulation Voltage Stress — Higher voltage stress in the motor connecting cables and motor insulation will lead to a shorter insulation lifetime. If any of the voltage transient peaks exceed the insulation corona discharge level (partial discharge level), the insulation will gradually degrade with each voltage pulse. When it has been sufficiently degraded, it will then fail.Most new “inverter rated” motors have triple layer insulation which has a 1600 to 2000 volt partial discharge level. This will make them suitable to withstand the double voltage peak transient from a 600 volt inverter. It is wise to make sure of this fact, since a “standard” induction motor will only withstand about 1200 volts. Use of a standard motor in this application would shorten its life drastically. This can sometimes be as little as a matter of hours."

Jan 1, 2000

By Adriano Gonçalves dos Reis

In the development of the structural materials for the advanced applications, as in the aerospace industry, there is a constant strive to increase both strength and toughness. Maraging steels are iron-nickel alloys designed to combine both properties that are achieved through the age-hardening of low carbon martensite. This alloy have a metastable martensitic structure that can revert to austenite when heated in temperatures close to the aging temperature, and this effect can be enhanced with the temperature increasing and time of treatment. Therefore, the study of creep behavior in elevated temperatures has technological importance to the development of this material. In this work the creep behavior of a maraging 300 steel solution annealed is evaluated by carrying out creep tests at 650ºC and in a stress of 200, 300 and 500 MPa. Creep parameters, such as steady state creep rate (?????), final creep time (tf), and stress exponent from secondary creep (n) are determined, considering that they are important to evaluate the creep resistance of the material.

Aug 7, 2018

By Carla Lupi, Alessandro Pescetelli

"Spent lead battery recycling still shows few weak points in the achievement of a 100% recycling of different waste matters and by- products arising from the recycling process. Some of said problems are dealing with aqueous streams outgoing the recycling plant, and more particularly, a) the waste waters discarded from the breaking and separation unit, b) purification of the spent electrolyte drained from waste batteries and upgrade to a quality compatible with full re-use by the batteries’ manufacturers, c) purification of the mother liquors discarded in the sodium sulfate crystallization process so to produce a salt of commercial grade. All of the above listed problems have been satisfactorily overcome applying an electrochemical process that, through different process conditions and parameters, is able to remove the harmful impurities that hinder the successful commercialization of such by products, or, at least, that can avoid heavy and expensive treatment plant and operation.IntroductionAlmost 100% of commercial lead and lead alloys produced by secondary lead plants is recycled to the new lead accumulators manufacture. The other by-products and residues produced through the lead recycling process may be classified into two groups:a) matters reusable in the new accumulators production processb) matters produced as a result of various reagents and additives used in the recycling process, to be sold to different market sectorsQuality and saleability of by-products are significant points for the economics of the secondary lead plant operation, because, if said by-products are not saleable, they are just wastes, so offsetting potential revenues, and, at the same time, adding a heavy burden to operating cost, like disposal cost [1]. When looking at a typical, modern lead scrap batteries recovery cycle, it is quite evident that we are still rather far from dealing with a waste-less technology (fig.1).The group a) includes 3 by-products produced through the breaking process: among those matters the polypropylene only usually reaches a standard quality suitable for sale to lead manufacturing sector or to other sectors as well. The other two by-products, electrolyte and separators, do not still reach, through a viable and effective regeneration process, a quality standard sufficient for their re-use in the lead batteries sector ."

Jan 1, 2008

By Wolfgang Van Hooff

Encouraged by a strongly growing and evolving market for granulated products, Paul Wurth continuously improves its granulation and dewatering technologies to provide customers with state of the art installations. Continuously developed know-how about the granulation process of iron blast furnace slag enabled application to non-ferrous materials such as Ni-Slag, Pb-Slag, Blister Copper, Cu-Matte and even TiO2-Slag, which rank among the most difficult materials to granulate. This paper identifies how critical objectives in granulation and dewatering technologies applied to different molten materials with respect to various product quality objectives can be addressed. The differences between hot and cold water granulation systems are explained, including the step from cold runner to granulation water tank. Development of a flow and pressure controlled blowing box is the latest step to optimize the granulation process in order to meet the latest standards in terms of quality, power consumption and environmental protection.

Jan 1, 2006

By J. H. Rowland, A. C. Smith, K. A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame-resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68° C and 141° C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large-scale experimental configuration, the installation specifications of the fire suppression system and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature and limited water application on the suppression system performance.

Jan 1, 2010

By R. Wirth, B. Orberger, C. Wagner, A. Tudryn, B. Baptiste, S. Miska, Université Paris-Sud

Banded iron formations (BIFs) comprise complex textures and mineralogy, which result from fluid-rock interactions related to high and low temperature alteration. The initial iron oxy hydroxide mineralogy and associated phases such as carbonates, quartz, apatite and phyllosilicates were transformed leading to an upgrading of these BIFs into the world’s largest source of iron ore. In low-grade BIFs, a large part of the iron is related to micro- and nano- metric iron-bearing inclusions within micrometric quartz and/or carbonates (mainly dolomite). We studied laminated jaspilitic BIF samples from a drill core containing 26.71 wt.% total iron, 0.2 wt.% SiO2, 0.32 wt.% MnO, 15.46 wt.% MgO, 22.32 wt.% CaO, 0.09 wt.% P2O5, < 0.05 wt.% Al2O3, 0.15 wt.% H2O and 34.08 wt.% CO2 (Aguas Claras Mine, Quadrilatero Ferrifero, Brazil). Bright rose coloured dolomite and quartz bands alternate with massive specular hematite bands. Raman spectroscopy, X-ray diffraction and FIB-TEM analyses reveal that the micro- and nanometric inclusions in dolomite are mainly hematite and minor goethite, partly occurring as clusters in voids. Curie Balance analyses were carried out at different heating steps and temperatures on whole rock samples and a synthetic mix of decarbonated sample and pure dolomite. X-ray diffraction on the products of the heating experiments shows that that hematite is stable and new phases: magnesioferrite (MgFe2O4), lime (CaO), periclase (MgO), portlandite (Ca(OH)2) and srebrodoskite (Ca2Fe2O5) were formed between 680°C and 920°C. These finding gives hints to optimizing the beneficiation process, as the presence of hydroxyl ions bearing goethite micro- and nanoinclusions lowers the sintering temperature. Prior separation of coarse hematite and barren dolomite and quartz, followed by lower temperature sintering of the inclusionbearing dolomite/quartz leads to transformations into phases with higher magnetic susceptibilities (such as hematite and magnesioferrite). The entire Fe and Fe/Mg oxide feed (the priorly separated fraction added to the sintered fraction) can then pass through wet-high intensity magnetic separation after crushing.

Jan 1, 2016

By Henry M. Harris

The Bureau of Mines investigated a glass containing approximately 17 percent lithia and 83 percent silica to establish a method of devitrifying cast and rolled shapes. Glass shapes with high strength were made by melting, forming, and rapid cooling of the composition, and the shapes subsequently were converted to a crystalline condition by heat treatment. The best devitrification schedule included rapid cooling of the glass to below 300° C, followed by reheating at a rate of 50° to 400° C per hour, depending on the size of the shape, followed by a of 60 to 70 hours at 500° C and another period of 15 hours at 800° C. attempts to use faster heating rates or slow cooling to accomplish devitrification in deformation of the shapes. The crystalline shapes had flexural strengths that averaged over 33,000 psi, achieved with an annealing time of 60 to 70 hours at 500° C.

Jan 1, 1965

By M. A. Barakat

Large amounts of zinc ash and flue dust containing more than 80 % zinc are accumulated during galvanization processes at the surface of molten zinc bath and in the chimney respectively. Pyrometallurgical recovery of zinc from both of the ash and dust samples has been carried out. The ash was sieved with the help of an industrial sieve shaker provided with mesh sieve having a pore size 0.9 mm. The oversize fraction cut (+ 0.9 mm) was melted at 550 °C under ambient conditions. The produced ingot (1) was analyzed whereas the coarse fraction of the produced slag (+ 0.9 mm) was treated as the coarse ash or added to it. The dust was enriched with suitable fluxing salt prior to heat treatment at 600 °C for 1 h. The produced ingot (2) was analyzed whereas the resulting slag was mixed with the fines of the ash and treated by hydrometallurgical processing to prepare valuable salts of zinc. Parameters affecting recovery processes such as time, temperature and flux percentage were studied. Results obtained revealed that the two prepared ingots (1&2) were successfully recovered with recovery efficiency amounts to =85 %. The obtained samples meet the standard specifications with relatively low price. Also in the light of the strict environmental regulations of pollution control, reuse of these wastes materials will help in keeping the environment clean.

Jan 1, 2000

By A. C. Smith, J. H. Rowland III

The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) established a Technical study panel (the Panel) to provide recommendations on the utilization of belt air and new technology that may be available for increasing the fire resistance properties of conveyor belt used in underground coal mines. The Panel Report recommended use of the belt evaluation laboratory test (BELT) as the method for testing and approval of flame resistant conveyor belts used in underground coal mines. The research conducted to establish the correlation of the BELT with large-scale belt fire flammability tests was done using 91 - 107 cm (36- to 42-in.) wide conveyor belt. Due to today’s coal haulage capacity, the mining industry is using 183 cm (72 in.) and wider conveyor belts. The U.S. National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine if the BELT will also qualify wider belts as fire resistant for use in underground coal mines. This paper describes the results of recent experiments comparing results from using the BELT and the large-scale tests for six different belts.

Jan 1, 2011

By Clifford S. Gibson

THESE troubled times suggest three reasons for maximum effort to control silicosis: (1) To keep to a minimum the ever-increasing burden occasioned by past deficiencies in this respect. (2) To effect the greatest production with maximum efficiency, which means at the least cost. (3) To preserve man-power in every way. Good control of the silicosis problem aids these aims. Inadequate control hampers all three. Insofar as our knowledge goes, silicosis in Ontario mines is caused by the inhalation of finely particulate quartz. It follows, therefore, that removal of dust containing this mineral automatically erases the cause. The achievement of this ideal is the aim of the mine operator. His best tool to this end is ventilation. This paper discusses mine ventilation from the viewpoint of dust control and it is hoped that in so doing there may result a better understanding of the part played by air in silicosis prevention. No attempt will be made to treat the subject fully. Instead, there will be presented certain salient aspects culled from field observations, the data in all cases referring to gold mines, unless mention to the contrary is made.

Jan 1, 1942

By G. T. Fisher

The material requirements of carbide cutting tools for machining steel and cast iron are dependent on WC bonded with Co, with additions of TaCand TiC. The Bureau of Mines is conducting research to devise substi-tute materials, based on Ni-alloy-bonded TiC, for C-5-grade cutting tool applications. This substitution would result in less dependence on foreign sources for Co, Ta, and W, and use of lower cost materials. In this preliminary study, the Bureau investigated the effects of composition and processing variables on the transverse rupture strength and hardness of Ni-alloy-bonded TiC to identify compositions that exhibit promising mechanical properties. Further systematic modification of these compositions by soild-solution strengthening additions would subsequently be evaluated to obtain cutting tool materials with requisite properties and performance for C-5 applications. Compositions for evaluation were prepared by a powder metallurgy method of cold-pressing and liquid-phase sintering. Complementary analysis of compositions included chemical analysis, X-ray diffraction, energy-dispersive X-ray spectro-scopy, and density measurements. Based on results of this investigation, promising compositions were determined to be 59.37TiC-25Ni-5Mo-lO.63Mo2C, 59.68TiC-25Ni-3.33Mo-1.77Mo2C-6.67W-3.55WC, and 59.35TiC-25Ni-l.67Mo-3.54Mo2C-3.33W-7.1WC.

Jan 1, 1987

By J. W. Eckerd, W. S. Sanner, P. L. Woolf, R. E. McKeever

The Bureau of Mines experimental blast furnace was operated successfully with anthracite metallurgical briquets . Tuyère pressures were higher and more erratic than for operations using coke , and furnace " hangs " occurred more frequently . Higher hot - blast temperatures were required to maintain the quality of the metal . By using higher hot blast temperatures , the fuel and production rates and slag volumes were comparable to those obtained for all - coke operation . The anthracite metallurgical briquets exhibited excellent mechanical strength and descended through the shaft of the furnace with little breakage or reduction in size .

Jan 1, 1964

By Nikhil Dhawan, Veeranjaneyulu Rayapudi

This study investigates upgrading of low-grade banded hematite quartzite iron ore (Fe ~31%). Conventional beneficiation was found to be futile. The susceptibility of iron phases to microwave exposure and their selective absorption assists in the liberation of iron values. Microwave exposure of coarse particles at 540 W for 10 min yielded a concentrate with Fe 56.30% and recovery of 50.68%. Conventional carbothermic reduction at 500 °C, 60 min and 9% charcoal yielded a concentrate with Fe 57.6% and iron recovery of 68%. The presence of sufficiently bonded silica leads to an easy formation of a fayalite phase. The microwave reduction design yielded FeG of 57.6%, FeR of 47% and a yield of 24% at an optimal condition of 540 W, 8 min and 6% charcoal. It was found that a small fraction of microwave-irradiated ore-charcoal mixture melted rapidly, and pure ferrite balls were observed within 8 min. An optical micrograph of a ferrite ball reveals the retained austenite and martensite phase.

By N. Kyriazi

A performance study of oxygen self-rescuers from the United States and other countries was undertaken as an assessment of present worldwide technology. The apparatus were tested a an breathing and metabolic simulator in the Life Support laboratories of the Bureau of Mines. Parameters monitored during the testing were inhaled levels of C02 and 02, inhaled gas temperature, and breathing resistance. The metabolic demand placed on the apparatus represented the average demand of the 50th percentile miner performing a 60- min man-test 4, as described in 30 CFR 11H. Results presented include ;apparatus service life and subjective comments as well as averages and peaks of monitored parameters.

Jan 1, 1984

By T. A. O’Hara

SINCE May 1948, when tungsten carbide bits were introduced at the Flin Flon mine, they have been popular with the miners because of their fast drilling speed and low gage loss. The high cost of commercial carbide bits and tipped drill steel, however, prevented their use except for the hardest rock. In an effort to extend the use of tungsten carbide on a basis economically competitive with detachable steel bits, experimental work was begun in 1950 to test the feasibility of making tungsten carbide tipped drill steel in the mine drill steel shop. This work showed that tipped drill steel could be made locally at less than half the cost of the commercial product. The performance of the local tipped drill steel was comparable to that obtained with commercial carbide bits and tipped drill steel and the cost per foot drilled was much lower. Local tipped drill steel was adopted for all mine drilling in November 1951. Since then drilling costs per foot have been sharply reduced and footage drilled per manshift has increased markedly. Experience at Flin Flon has shown that production of satisfactory carbide tipped drill steel is not difficult and that highly skilled labor and costly equipment are not required. As long as wise selection of brazing materials is made and certain simple precautions are rigidly maintained, there is no reason why small mines with relatively unskilled labor cannot produce a satisfactory product. The following description outlines the technique used at Flin Flon for making carbide tipped drill steel and discusses characteristics of the brazing process that make special precautions necessary. Drill steel is forged to four-wing shape in a conventional steel sharpening forge. Standard steel dies are modified to minimize forging cracks around the central waterhole and to forge a blunt bithead on the steel. The steel is preheated to 1500°F and held at this temperature for at least 2 min. When the temperature has equalized throughout the steel section, the drill steel is transferred to the forging furnace and heated rapidly with a reducing flame up to 2000°F. This two-stage method of heating minimizes the grain growth and decarburization of the steel while ensuring that the steel temperature does not vary greatly throughout the forging zone. After forging the steel is allowed to cool in air to about 1600°F before being annealed in a bath of vermiculite. Despite the high hardenability of the 3 pct Ni-Cr-Mo drill steel used, this simple treatment anneals the drill steel sufficiently for milling. The forged and annealed drill steel is slotted on a plain horizontal milling machine that is equipped with a quick opening chuck and a slot depth stop. The full depth of the slot is milled in a single pass of the 3-in. milling cutter which is fed at 33/4 in. per min across the crown of each bit wing. The slots are cut to a width of 0.342 to 0.344 in. Maintenance of this slot width is necessary to ensure that the optimum brazing clearance of 0.002 in. will result after assembling of shims and carbide in the slot. Prior to March 1953, when the milling machine was installed, drill steel was slotted on a small manually fed ¾ hp milling attachment mounted on the bed of a lathe. Over 16,000 drill steels were slotted on this unit, and in view of its small size and low cost it gave excellent service. Brazing of Tipped Steel Drill steel that has been milled and cleaned in carbon tetrachloride is mounted in a rotating cradle holding six drill steels, the length of which may be from 2 to 12 ft. The slots in the drill steel, the shims, and the tungsten carbide inserts are thoroughly fluxed with a fluoride flux and assembled as shown in Fig. 1. Fig. 2 shows the brazing equipment in use. As the ring burner is lowered over the bithead a spring valve opens the gas lines, and the gas mixture, preset to give a slightly reducing flame, is fed to the ring burner where it is lit from a pilot flame. The ring burner heats the drill steel over a zone about 1 to 2 in. below the bithead, which becomes heated by conduction through the steel. By this means the bithead is heated rapidly and evenly, and contamination of the brazing joint with soot from the flame is avoided. The bithead is heated to the melting temperature of the brazing alloy within 1 min. This rapid heating minimizes the disadvantage of a non-eutectic brazing alloy. The brazing alloy, a nickel-bearing quaternary alloy, is placed at the bottom of the slot below the carbide insert, as shown in Fig. 1. As the brazing alloy melts it is drawn by displacement by the carbide and by capillary action into all parts of the joint to displace liquid flux from metal surfaces. As soon as the brazing alloy melts, each insert in turn is wiped by being moved back and forth along the slot. This action assists wetting of the carbide by the brazing alloy and assists in displacing molten flux from the joint. After continuous heating for about 75 sec, when the bithead has reached a temperature of about 1500°F, the ring burner is raised and the gas supply is shut off automatically by the spring valve. As soon as heating is stopped a hand press is placed on the bithead and the inserts are squeezed down firmly. This action minimizes the clearance between the bottom of the insert and the slot. Correctly brazed steel should maintain a clearance at the bottom of the slot of 0.001 to 0.002 in. After six steels have been brazed they are removed from the cradle and allowed to cool in air. As soon as each drill steel is cool it is dressed on a grinding wheel to remove excess flux and braze and is ground to the gage appropriate to the length of the drill steel.

Jan 1, 1955

By H. U. R. Kattentidt, W. L. Dalmijn, T. P. R. de Jong

"Research at Delft University aims to develop systems for automatic inspection and sorting of bulk solids which can be applied in the mineral processing and recycling industry. A recent development includes an automatic sorter based on airport X-ray inspection technology. It is designed for continuous inspection and sorting of 5 - 150 mm solids and has as objective a cost effective and high capacity on-line inspection and sorting.Dual energy X-ray transmission imaging provides instantaneous data about particle dimensions and the atomic number distribution. The system provides particle thickness and average atomic number on a pixel level at scanning speeds between 250 and 500 lines / second. With existing X-ray components inspection speeds between 0.5 and 2 m/s at approximately 1-meter inspection width and between 1.5*1.5 and 5*5 mm2 sensor resolution can be achieved.Imaging algorithms that were developed by Delft University for applications in recycling, waste cleaning and other applications acquire shape, size distribution and composition data. Currently on-line processing of a product at a rate of around 200 particles per second is possible using a standard PC. Experiments with a demonstration X-ray unit indicated good potential for various applications in solids processing. They include continuous inspection of organic content, sulphur, chlorine, ash, and metal distribution. It is applicable for coal cleaning, ore sorting, industrial minerals, and various applications within waste cleaning and recycling. Dual energy X-ray transmission fundamentals and recent progress in system development and applications are presented."

Jan 1, 2003

By J. Mullins

Coal was first banked by the Dominion Coal Company, Limited, in 1898, near No. 2 Colliery, the same site as is presently used for that purpose. Though today there are banks at Glace Bay, Sydney, and Sydney Mines, these notes, except when otherwise desirable, will be confined to describing the practice as developed at the No. 2 Banking Station, Glace Bay, as being typical of methods obtaining at all sites. Storing The manner in which the coal was piled is illustrated diagrammatically in the accompanying sketch. A train of coal was brought on the main trestle, which extended the full length of the banking ground at a height of 22 to 39 feet above the natural surface, and dumped into bins which were integral with the trestle work. Chutes from these bins permitted the coal to be fed into 3-ton cars, which were horse drawn laterally on narrow gauge tracks laid about 10 ft. centres, to a maximum distance of 400ft. from the trestle. These cars were end-dump and as the pile extended laterally the narrow gauge tracks were lengthened by shorter or longer filling pieces, so that their ends were always kept at the brow of the bank. Much coal, however, had to be dumped directly on the tracks and hand trimmed to fill the valleys, and level off, between the tracks.

Jan 1, 1931

By Umay Cinarli, Ahmet Turan

High-energy consumption in primary aluminum production (from bauxite ores) makes secondary aluminum production (from metallic raw materials such as scrap and dross) very critical. Aluminum dross, as a waste, arises in pyrometallurgical processes, and it is the mixture of metallic Al, Al2O3, other metal oxides, metal halides, and some other compounds like AlN. Aluminum dross has two subgroups (white and black) with respect to its metallic aluminum content. White dross is a secondary aluminum resource because of its high metallic aluminum content, whereas black dross, having low metallic aluminum content, is generally disposed in dumping areas. In the present study, it was aimed to develop a simple technique to valorize aluminum black dross in the form of alumina-based ceramic materials through pyrometallurgical (calcination) and hydrometallurgical (leaching) operations. Moreover, thermochemical simulations were conducted by using HSC Chemistry 6.12 software to simulate calcination conditions. After leaching experiments, an alumina-based ceramic containing approximately 36.8% Al2O3, 61.4% MgAl2O4 with 1.8% Na2FeO4, which might be available to use as a spinel refractory in steel smelting furnaces, was obtained in the experiment carried out in a solution containing 10 mLH2SO4 and 40 mL distilled water (3.5 M). Moreover, the sinterability of the alumina-based ceramic was investigated at the temperatures from 1350 to 1550 °C. In the sample which was sintered at 1550 °C, a density value of 3.15 g cm−3 and a hardness value of 69.58 HV were measured.

Oct 26, 2020

By A. E. Halim, J. F. Brune

The 2006 Sago, Darby, and Aracoma mine disasters in the United States (US) forced the US government to implement the 2006 MINER Act and additional regulations that require all US underground coal mines to install and maintain refuge chambers to manage entrapment emergencies, in particular, fires and explosions. However, there is a debate on whether barricading in refuge chambers is a good strategy to survive such emergencies. Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes merits and problems of using refuge chambers and self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. The authors found that the use of refuge chambers may not be the best strategy during extensive fires or when multiple explosions happen. In these situations, mine rescuers are unlikely able to extract miners who are sheltered in chambers and conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as Level 1 Emergency Exercises required in the Australian State of Queensland. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.