Search Documents

By H. H. Kaveler, W. R. Evans, Jack Tarner

The geological features, development history and engineering detail of the Shuler Field and the results of approximately two years of unitized operation of the Shuler Jones Sand Pool, were discussed in a prior publication.' The purpose of this paper is to present the results of pressure maintenance in the Shuler Jones Sand Pool after nine years of unit operation. GENERAL INFORMATION The Shuler Jones Sand Pool is located in and about Section 18, Township 18 South, Range 17 West, Union County, Ark. The pool was discovered .in September, 1937, unitized in February, 1941, and subjected to gas injection operations in July, 1941. Water was first returned to the reservoir in July, 1944. The reservoir is an anticlinal trap covering about 4,000 acres. The 154,000 acre-ft of sandstone initially consisted of approximately 150,000 acre-ft of productive oil zone and 4,000 acre-ft of gas-cap. The average depth of production is 7,400 ft. Maximum closure of the reservoir is 135 ft and the oil column lies between a gas-oil contact at -7,270 ft and a water-oil contact at -7,370 to -7,380 ft. The field is approximately four miles long. east and .west, and one and one-half miles wide. The sand grains are angular and vary from fine to medium size. The porosity of the sandstone averages 20.2 per cent. The specific permeability averages 400 md. Some zones have as high as 30 per cent porosity and specific permeability of 4,000 md. The reservoir rock is not uniform in character but consists of sandstone zones interspersed with shale. The variation in rock characteristics is evident in the electric log and core analyses presented in the original publication. Asphalt present in the pore space of the sandstone limited the reservoir to the southeast and apparently blocked any encroachment of water from that direction. The initial reservoir pressure at a subsea depth of 7,300 ft was 3,520 psi. The reservoir temperature was 198ºF. Initially, the solution gas volume was 765 cu ft per bbl and the reservoir volume factor was 1.45. The gas solubility and formation-volume-factors of the reservoir liquid are related with reservoir pressures above 300 psi as follows: Solution gas, cu ft per cu ft, S = 0.0334 P + 18.65 Formation volume factor of reservoir oil, FVF = 8.0 x 10 -5 P + 1.168 Gas volume factor, standard cu ft of gas equivalent to one cu ft of gas at reservoir conditions of temperature and pressure, F = .062 P - 4 Pressure (P) measured in psia. The equation for the gas volume factor presented above is based on a direct measurement of a sample of the gas and is a correction of that used in the original paper. The gravity of the oil produced is from 32 to 34" API. CALCULATION OF INITIAL OIL IN PLACE The Jones Sand production history is interesting because it lends itself to analysis by material balance. Production statistics from discovery of the Jones Sand through 1949 and material balance calculations of the initial stock tank oil in place are shown in Table I. The usual procedure in testing the application of material balance calculations is to compute the apparent initial volume of oil in place, using production and pressure information obtained at different time periods. If the apparent oil in place volumes computed increase with successive time periods, water encroachment is indicated and approximations must be mads to correct for its influence. The first requirement in utilizing such calculations is reliable reservoir pressure, accumulated gas, oil and water production, and PVT data. Calculations of apparent oil in place in the Jones Pool, based on field data

Jan 1, 1951

By Priscilla P. Nelson, Francis L. C. Fong

Introduction Fracture mechanics is the study of the behavior of cracks and their modes of propagation. During cracking, energy is consumed in creating new surface area. The more energy a material absorbs, the higher is its fracture resistance. This fracture energy is provided either by work done externally, by the release of elastic strain energy within the cracked body, or by a combination of these two effects. Fracture resistance is measured in terms of either the stress intensity factor, K, or the energy release rate (also referred to as crack driving force), G. For linearly elastic materials, these two quantities are related by the following equation: [ ] where [u] is Poisson's ratio and E is the modulus of elasticity. Both K and G are direct functions of the applied force and the crack length. The process of rock cutting with full-face tunnel boring machines (TBMs) involves the indentation of a rock surface by rolling disc tools. Excavation occurs as fractures, extending from the locus of chip indentation, propagate between concentric disc grooves and liberate rock chips from the intact rock face. Since disc cutting is achieved by a fracture process, it is logical to anticipate that differences in cuttability of a variety of rocks should be related to the variation of fracture material properties among the rocks. Such a relation has been demonstrated between the performance of full-face TBMs and the critical crack driving force for excavation in relatively high strength, brittle, low porosity, isotropic rock (Nelson et al., 1985). The objective of this paper is to report on the results of a continued investigation of the relationship between fracture material properties and the effectiveness of disc cutting. Additional reliable data on full-face TBM performance is difficult to obtain, so that the results of disc linear cutter tests performed by the Transport and Road Research Laboratory (TRRL) (U.K.) are utilized in this study. Fracture Material Property Evaluation If a crack tip is subjected to a perfectly plain strain condition, many materials will behave in a brittle manner, and the material resistance to fracture is constant during crack growth. This resistance is referred to as the plain strain fracture toughness, believed to be a material property. The standard testing procedure for this parameter is given in the American Society for Testing and Materials (ASTM) test designation E399. To ensure plain strain conditions, acceptable specimen geometries are specified. Unless these geometric specifications are adhered to, the measured fracture resistance is regarded as the apparent fracture toughness, and a subscript Q is used, as [ ]. The methodology adopted by ASTM E399 is within the framework of Linear Elastic Fracture Mechanics (LEFM). This approach assumes that material resistance against cracking is developed instantaneously, without initial stable or subcritical crack extension. Prior to crack advancement in rock, however, much of the crack driving energy is absorbed in a localized volume in front of the crack tip, referred to as the plasticity or microcracking zone. This capability for energy absorption substantially increases material resistance, and a crack may be arrested unless an increased crack driving force is applied. The LEFM or plain strain assumptions would underestimate the actual fracture resistance of such a material. Such a conservative approximation may be desirable in the design of structures against fatigue or brittle failure. In mining or tunneling, however, an underestimation of crack resistance can lead to the selection of underrated excavation equipment and a decrease in production efficiency. The development of fracture resistance in rock is best described by the material resistance curve, or R-curve, which is a plot of fracture resistance as a function of crack extension. Typically, peak resistance is only reached after a finite amount of subcritical crack growth. The

Jan 1, 1986

By W. R. Evans, H. H. Kaveler, Jack Tarner

The geological features, development history and engineering detail of the Shuler Field and the results of approximately two years of unitized operation of the Shuler Jones Sand Pool, were discussed in a prior publication.' The purpose of this paper is to present the results of pressure maintenance in the Shuler Jones Sand Pool after nine years of unit operation. GENERAL INFORMATION The Shuler Jones Sand Pool is located in and about Section 18, Township 18 South, Range 17 West, Union County, Ark. The pool was discovered .in September, 1937, unitized in February, 1941, and subjected to gas injection operations in July, 1941. Water was first returned to the reservoir in July, 1944. The reservoir is an anticlinal trap covering about 4,000 acres. The 154,000 acre-ft of sandstone initially consisted of approximately 150,000 acre-ft of productive oil zone and 4,000 acre-ft of gas-cap. The average depth of production is 7,400 ft. Maximum closure of the reservoir is 135 ft and the oil column lies between a gas-oil contact at -7,270 ft and a water-oil contact at -7,370 to -7,380 ft. The field is approximately four miles long. east and .west, and one and one-half miles wide. The sand grains are angular and vary from fine to medium size. The porosity of the sandstone averages 20.2 per cent. The specific permeability averages 400 md. Some zones have as high as 30 per cent porosity and specific permeability of 4,000 md. The reservoir rock is not uniform in character but consists of sandstone zones interspersed with shale. The variation in rock characteristics is evident in the electric log and core analyses presented in the original publication. Asphalt present in the pore space of the sandstone limited the reservoir to the southeast and apparently blocked any encroachment of water from that direction. The initial reservoir pressure at a subsea depth of 7,300 ft was 3,520 psi. The reservoir temperature was 198ºF. Initially, the solution gas volume was 765 cu ft per bbl and the reservoir volume factor was 1.45. The gas solubility and formation-volume-factors of the reservoir liquid are related with reservoir pressures above 300 psi as follows: Solution gas, cu ft per cu ft, S = 0.0334 P + 18.65 Formation volume factor of reservoir oil, FVF = 8.0 x 10 -5 P + 1.168 Gas volume factor, standard cu ft of gas equivalent to one cu ft of gas at reservoir conditions of temperature and pressure, F = .062 P - 4 Pressure (P) measured in psia. The equation for the gas volume factor presented above is based on a direct measurement of a sample of the gas and is a correction of that used in the original paper. The gravity of the oil produced is from 32 to 34" API. CALCULATION OF INITIAL OIL IN PLACE The Jones Sand production history is interesting because it lends itself to analysis by material balance. Production statistics from discovery of the Jones Sand through 1949 and material balance calculations of the initial stock tank oil in place are shown in Table I. The usual procedure in testing the application of material balance calculations is to compute the apparent initial volume of oil in place, using production and pressure information obtained at different time periods. If the apparent oil in place volumes computed increase with successive time periods, water encroachment is indicated and approximations must be mads to correct for its influence. The first requirement in utilizing such calculations is reliable reservoir pressure, accumulated gas, oil and water production, and PVT data. Calculations of apparent oil in place in the Jones Pool, based on field data

Jan 1, 1951

By C. D. Hall

This paper may be divided into two main parts: (1) analysis and data to show that Eq. 6 adequately correlates the authors' experimental data, and (2) the assertion that Eq. 20 "should permit scale-up with data taken from one pipe diameter for Newtonian, inelastic non-Newtonian, and viscoelastic fluids, such as dilute polymer fracturing fluids, which produce considerable pressure reductions." The authors might well recommend that this broad grouping of fluid types could be correlated by using Eq. 6 (requiring data from at least two pipe diameters). On the other hand, Eq. 20 is only shown to be adequate for conditions within the range of the present data set. Specifically, predictions by Eq. 20 for diameter scale-up to casing sizes would give larger deviations than implied in Table 2, and scale-up for some other fluids that give large drag reduction could be grossly in error. The description of a class of fluids "which produce a diameter family of straight parallel lines on a log (d?p/4L) vs log (8 v/d) plot. . ." defines a necessary condition for using Eq. 6; i.e., that s shall be constant for each fluid. The proposal that Eq. 20 is applicable to turbulent flow of such fluids is equivalent to saying that the spacing of these parallel lines, with A being constant, will be found to correspond to m = -1.20 for all such fluids. Table 1 shows the values of m derived from data on 16 non-Newtonian fluids. The key statement of this paper is that the diameter exponents "do not vary significantly from . . . -1.20." In statistical terms, this says that the m value for each fluid, which was obtained from all the measurements made on that fluid. has not been shown to be different from the arithmetic mean of the m values for the 16 fluids tested. This implies that the group mean, -1.20, is a more reliable value to use for an individual fluid than is the m value derived from the data on that fluid alone. No statistical test is described to support the key statement that the diameter exponents do not vary significantly from -1.20. Such a test would have to take into account that each individual m value is shown to correlate the pressure gradients for its fluid, with only about 3 percent standard deviation over the diameter range covered. That is, the m value is not the result of a single independent measurement. Thus, it would not be sufficient, or valid, to compare the deviation of one of the m values with the variance of the 16 values of m about their mean. An alternative interpretation of the key statement is that the diameter exponents do not vary appreciably from -1.20; i.e., that using -1.20 does not cause serious inaccuracy. Table 2 seems to be offered in support of such an assertion. However, such a statistical treatment (1) is unnecessary and (2) cannot lead to any valid scale-up generalization. The amount of error introduced by using a 1"wrong" value of diameter exponent — i.e., -1.20 instead of m — is determined by Eq. 6. The ratio of the pressures predicted by Eqs. 6 and 20 for scale-up from ds in small pipe to d, in casing is The pressure for 30-percent calcium carbonate slurry (m = -1.112) in 10-in. ID pipe would be predicted 30 percent higher by Eq. 6 than by Eq. 20, if based on tests in 0.5-in. ID pipe. The data set tested in Table 2 represents only a limited sample of pipe diameters (ratio of about 4:l) out of the population of diameters that would

Jan 1, 1970

By A. K. Mukhopadhyay, B. Sikdar, V. P. Arora

Introduction During the past several years, persistent concerns about an economic slowdown in India have tempered capital-expan¬sion plans. This has encouraged companies to find methods of increasing the capacity of existing production equipment. One of the more cost-effective methods of increasing produc¬tion capacity without major capital investment is to improve equipment maintenance to prevent needless machine down¬time. This can have a significant financial impact because of reduced maintenance costs and increased machine availabil¬ity. The maintenance program employs different techniques, but the analysis of the vibration behavior of machine compo¬nents to assess their condition was found to be the most accurate technique for monitoring various machine disorders. A dragline that handles overburden in open pit mines is one of the more capital-intensive pieces of production equip¬ment. It is imperative that the machine be run at its optimum capacity under the prevailing environmental conditions. Condition monitoring of the various components of the dragline through vibration analysis not only improves the machines availability but also ensures a long operation time free from sudden failure. This paper describes the application of vibration monitor¬ing and analysis techniques to assess the components of a W2000 dragline. The paper reveals that condition monitoring through vibration analysis can be as valuable in failure prevention as it is in failure analysis. Finally, the paper presents an approach to a knowledge-based expert system to the quick and correct diagnosis of mechanical faults in a dragline. Equipment A dragline is an intermittent-discharge-type excavator having a long boom at one end. Unlike other excavators, the bucket is not rigidly held by the frame structure. In favorable geomining conditions, the intensive operation of these exca¬vators is the least-expensive means of overburden removal. The basic working elements of this equipment are the hoist system, the crowd and retract system, the wing mechanism and the propel mechanism. The walking dragline is accepted as the most economical machine for stripping overburden at depths of up to 60 m (200 ft). They are electrically powered and the various motions are effected by individual drives. The Ward-Leonard system is used to provide the optimum flexibility in controlling different dc-drive motors. To mini¬mize the cost of mineral extraction, the largest such machine in India has a 24-m3 (850-cu ft) bucket with a boom length of 96 m (315 ft). Draglines are very costly, and considerable financial penal¬ties may arise from sudden stoppages due to component fail¬ures. Thus, operational reliability is of the greatest importance. Active measures are now being taken to minimize downtime by adopting condition-based maintenance techniques. Though a number of techniques come under this scheme, it has been observed that assessing the health of the dragline by measuring vibration is the best method of determining the dynamic behavior of its various rotating components to avoid any catastrophic failure. Based on criticality, the vibration-behav¬ior of the following components are studied: • motor-generator unit, • exciter unit, • hoist motor-gearbox unit, • hoist drum-gearbox unit, • drag motor-gearbox unit, • drag drum-gearbox unit and • swing motor unit The approach Increases in the vibration levels in different subsystems of the dragline were observed due to the presence of faults such as unbalance, misalignment, looseness and bad bearings. A vibration behavior study included the measurement of vibra¬tion level, trend analysis of time-domain vibration signals and vibration frequency analysis at bearing points of the components. A vibration meter, a vibration analyzer and a data collector are used. Vibration-level measurement. When the dragline was assembled and put into operation for the first time, vibration data were collected to generate baseline data for the equip¬ment (based on International Standard ISO 2372). After¬wards, the vibration levels were recorded regularly using a vibration meter. The measurements were taken at all bearing

Jan 1, 2000

By Nobumasa Kemori

Six kinds of copper '90ncentrates. were treated individually in a ,pilot scale. Outokumpu flsah smelting furnace ~n order to study their ?flash smelting behavior with respect to oxygen efficiency and dust generation. The copper concentrates tested were selected from the more than twenty sources which are treated at the Sumitomo Toyo copper smelter, so as to provide a wide range of chemical composition in terms .of Cu, S,Fe, Pb + Zn + As, and Si~ content. Oxygen efficiency 'and dust generation rates obtained in 'the experiments ranged from 80% ,to 108% and 11% to 20%, respectively. Relationships between these results and experhnental conditions such as chemical and mineral composition of the copper concentrates, flux ratio, fuel consumption and so on are also discussed quantitatively in this paper.

Jan 1, 1998

By AIME AIME

WAR undoubtedly accelerates metallurgical progress, although its most obvious effect is a tremendous waste of materials. The necessity for restrictions in normal uses of metals results in a search for substitutes or for enhanced properties that will make a limited supply last longer. An insatiable demand for more metal to be produced more quickly favors trial of new processes, new metallurgical tools, and new methods of fabrication. Greatest advance is made, of course, in practical physical and process metallurgy. Theoretical or fundamental research necessarily must take a secondary position, and is so regarded in this review. It is not that developments in theoretical physical metallurgy are lacking entirely, but, following the same trend noted in other countries as they entered war activities, attention in the U.S.A. has been shifted strongly to those developments having an immediate practical application.

Jan 1, 1943

By António A. Henriques, António Gomes Correia, Ana Teixeira

"Abstract Pile foundations are often used for important structures, and thus, reliability evaluation is an important aspect of the design. Reliability methods have become increasingly important as decision support tools in different areas. The main benefit of reliability analysis is that it provides quantitative information about the parameters (uncertainties) that most significantly influence the behaviour under study. In particular, the design of pile foundations still involves many limitations and uncertainties, particularly when there is not enough investment in soil characterisation and/or pile load tests. In addition to the uncertainties associated with soil characterisation, physical, statistical, spatial and human uncertainties exist. In this subject, the primary purpose of this paper is to demonstrate the application of reliability methods to geotechnical pile design (axial load). It also presents a simple and practical approach to performing it using Monte Carlo Simulations, intending to provide knowledge for code harmonisation and encouraging the development of such methodologies in geotechnical practice. Sensitivity analyses are shown to understand the influence of each uncertainty type coming from different sources. An application example indicates, corroborating other studies, that the model error is the most influent uncertainty. As such, when using the different models (SPT-, CPT- and PMT-based) for bearing capacity, the results emphasise the need for a well-defined and wellcharacterised resistance model, also these results allow the engineer to understand how important the load tests can be to achieve reliable results and economic designs.1 IntroductionUnlike the approach to reliability evaluation used in structural engineering, the traditional procedure used in geotechnical designs addresses uncertainties through high global or partial safety factors (SF), mostly based on past experience. However, this approach to addressing uncertainties does not provide a rational basis for understanding their influence on design.Furthermore, the new regulation codes and social concerns, such as the sustainability or the economy, are imposing geotechnical engineers to increase their ability to deal with uncertainty in a direct and more rational way. Designs should be economic, sustainable and reliable at the same time. Concerning the reliability part of design, different approaches can be done, but the most important thing to keep in mind is the simplicity and efficiency of the tools and applied methods."

Jan 1, 2014

By S. N. Monteiro, C. M. F. Vieira, A. P. N. M. de Sa, J. P. D. Vitorino

"This work has as its objective to characterize an ash waste and to evaluate its incorporation into a clay to produce bricks and roofing tiles. The waste is a type of fly-ash resulting from the incineration of a selected part of urban garbage, which is basically constituted of organic matter and plastics. The waste was submitted to mineralogical and chemical characterization. Compositions were prepared with incorporation of the waste in amounts of up to 20wt.% into athe clay. Rectangular specimens were prepared by extrusion and fired in a laboratory furnace at 900°C. The physical and mechanical properties evaluated were: linear shrinkage, water absorption and flexural rupture strength. The results showed that the waste is predominantly composed of quartz and calcium compounds. The incorporation of the ash was deleterious to the evaluated properties of the clay. It is suggested that the incorporation should be made in amounts below 5wt. % to avoid deleterious effect in the mechanical strength and water absorption of the clayey ceramic.IntroductionThe world attention has turned to a subject of great concern today, the production and disposal of large amounts of industrial wastes as well as wastes of various sources. When deposed in an unsuitable place, these wastes can cause considerable harm to human health and to the environment. Our planet suffers with air pollution, groundwater and soil contamination as well as silting of rivers and lakes with the growing amounts of our society wastes.The recycling of waste materials is of great interest to the industries, mainly due to the environmental agencies legislation. One of the practices for correct disposal of these wastes being investigated is to incorporate into red ceramics, such as bricks and roofing tiles. The natural variability of the characteristics of the clays associated with the relatively simple processing techniques and also the low performance required for the products allow the presence of relatively high levels of impurities in clayey ceramics."

Jan 1, 2011

By Donald W. Ross

Petroleum oils of widely different grades have long been clarified or decolorized by contact with fuller's earths. More recently, so-called activated clays have also been used for this purpose. Still more recently ouch clays have been used in the form of nodules termed "catalytic pellets." Clays of varied appearance and from different localities possess the desired bleaching qualities, but evaluation of such clays, so useful to the oil industry, has not been simple. Previous methods of identification and evaluation have largely followed procedures of production methods and were not primarily based upon the fundamental properties of the clays. Thus) a false assumption has grown up that) bleaching clays probably have no common properties on which a-method of comparison can be based. Fuller's earths and activated clays have a large absorptive capacity for the color constituents of petroleum and its products decolorizing is accomplished by bringing the oil into intimate contact with the clay and later separating the decolorized oil from the clay with its load of absorbed coloring matter. Former practice in absorbing "color" was to use the clay as granules or In' powdered form. More recent practice is to use clay pellets that are more abrasion-resistant than the granules. The oil is either filtered through a bed of clay, percolation method, or agitated on contact with the clay, contact method. Viscous oils are decolorized at an elevated temperature, so that their viscosity is lowered to the point at which thorough contact with the clay is insured. Nonhumidifying, nonoxidizing gas, such as dry steam or dry nitrogen, is used to seal such hot oil masses from the atmosphere.

Jan 1, 1948

By T. A. Rickard

The dictionary defines 'jargon' as "barbarous or debased language". This description does not suffice. Quiller-Couch has said, it is "a kind of writing which, from a superficial likeness, commonly passes for prose in these days, and by lazy folk is commonly written for prose, yet actually is not prose at all ". The two main vices of jargon, he says, are "that it uses circumlocution rather than short straight speech", like the Babu who reported his mother's death by saying: "Regret to inform you, the hand that rocked the cradle has kicked the bucket ". Its other chief' vice is that "it habitually chooses vague woolly abstract nouns rather than concrete ones", like the newspaper statement; "He was conveyed to his place of residence in an intoxicated condition", instead of saying, "He was carried home drunk ". Jargon is "an infirmity of speech", it is not journalese, but akin to it. "Like respect- ability in Chicago, jargo4 stalks unchecked in our midst" and renders much technical writing ridiculous. It deals in periphrasis instead of going straight to the point, it loves the abstract rather than the concrete, it dabbles in words of sound rather than of meaning. Avoid it, despise it., if you purpose earnestly to write well. "III literature as in life he makes himself felt who not only calls 4 spade a spade but has the pluck to double spades and re-double." * Jargon is rampant in technical publications. Catalogues and other advertisements are conspicuous offenders, but with these the critic is not concerned, except in so far as such 'write-

Jan 1, 1931

By Q. H. Liao, B. G. Monaghan

The options for designing slopes in complex geological conditions are reviewed. It is shown that modelling, especially numerical modelling, allows a degree of analysis that cannot otherwise be achieved. Examples are presented of how numerical modelling can be used to investigate fundamental aspects of rock mass behaviour. It is demonstrated that an important consequence of change in scale is that the mechanisms of failure also change. The complex failure of the footwall slope at Aznalcollar, a large open-pit mine in southern Spain, is discussed. Numerical modelling with UDEC (universal distinct-element code) has allowed the realistic simulation of displacements measured in the field

Jun 18, 1905

By N. A. Barcza

DC plasma-arc technology using a hollow graphite electrode (cathode) has been successfully implemented in the primary metallurgical industry in South Africa up to the 30 MW scale. Mintek has applied its expertise base, established over the past fifteen years, to testing the treatment of metallurgical wastes such as carbon- and stainless-steel plant dusts, lead- and zinc-containing slags, and residues from the base-metal industry. Favourable results have been achieved, and disposable products were produced. The evaluation of numerous wastes indicates that recovery of zinc as metal gives the best economic return from these sources. Direct recovery via a splash condenser or electrolytic zinc extraction from fume are the two preferred alternatives under review. In both instances dehalogenation is an important issue, but can be achieved by suitable treatment processes. The Enviroplas technology provides a flexible, commercially viable approach to the treatment of a wide variety of wastes. Mintek, together with its associate Pyromet CC, are installing a plasma- arc pilot-plant facility with both an ISP lead-splash condenser of about 5 t/d condensed zinc capacity and a combustion chamber to burn zinc vapour to zinc oxide. This will demonstrate the suitability of the Enviroplas technology for treating specific metallurgical wastes, so that customized industrial plants can be engineered based on large-scale testwork.

Jan 1, 1994

By D. Mireku-Gyimah, R. S. Suglo

Ghana contains auriferous belts which cover 51 800 km2 of its small area of 239 400 km2. From 1493 to 1600 35.5% of the world gold production was from the Gold Coast (renamed Ghana in 1957). This dropped to 8.9% from 1701-1800. For the past fifteen years annual production has averaged less than 2% of the world total. By 1985 only four gold mines were operating, compared with 45 in 1934 and 11 in 1945. Since 1987 Ghana has experienced a boom in gold mining activities. By 1991, 83 new companies had acquired prospecting licences. At least five new companies have started large-scale production. About 650 licensed small-scale mining groups are in operation. The economic and technological factors that have contributed to the decline of gold production in Ghana are discussed. A summary is given of the methods used to mine and recover gold. These cover small-scale workings, dredging, open cast operations and underground mining. The advantages and disadvantages of these technologies and the future of gold mining in Ghana are considered.

Jan 4, 1993

By D. Moses, J. A. Onyango

Carbonatites are generally competent rock masses with rock mass rating class II rating 60–74. In spite of their competency, they tend to be affected by weak features like manganese-iron veins and/or in situ rock damage due to brecciation associated with carbonatite complexes. Rock slope failure in such hard rocks is complex since such structures within the rock mass form weak links that could potentially control slope instability. In this contribution, a numerical simulation using phase2 v 7.0 was carried out to investigate the influence of in situ rock damage on the stability of mine pit walls. The outcome reveals that, the existence of breccia in the competent rock mass has the capability to reduce the slope stability performance particularly at gentle dipping angles of emplacement in close range to the slope toe. However, as the emplacement position of breccia moves away from the pit wall, the stability performance increases at gentle dipping angle <50º. On the contrary, at the dipping angle of 50° the performance of slope reduced, and at steeper angles >50° the impact becomes negligible. Thus, from a series of analyses, mine design in brecciated rock masses, the ratio of 1:5 between the breccia distance from slope toe and pit depth should be implemented to counter its impact, and if the breccia is within or close to the pit limit, a deliberate effort must be made to mine it out.

Sep 1, 2025

By E. Morrice

The metallurgical laboratory data developed in this study indicate an improved electrowinning process for producing higher purity cerium ingot. A typical sample of the Reno electrocerium contains 99.9 weight-percent cerium and the following impurities: Total other rare-earth elements, less than 0.04 percent; iron not detected; silicon and aluminum, less than 0.02 percent each; calcium plus magnesium, less than 0.01 percent; carbon, 0.01 percent; oxygen, 0.002 percent; hydrogen, 0.0003 percent; and nitrogen, 0.0015 percent.

Jan 1, 1960

By W. E. Oching, M. M. Ghomshei

"Collaboration among Ventilation Engineers, Mine Inspectors, worker representatives, health and safety officers and management is key to an effective operational mine ventilation management. Mine ventilation training, ventilation survey reports for mine stakeholders and interaction with mine frontline workers and management concerning safety, energy saving, assets management and maintenance are effective tools in implementing best industry practices and significant reduction of ventilation operating costs without compromising safety. These approaches may not be new to well established mining companies but the real dilemma is how to implement them effectively and this is what this paper will address.INTRODUCTIONManaging an effective mine ventilation system is becoming increasingly challenging, especially during tough economic times in the mining industry. Management strives for more production while frontline miners work hard to surpass the production targets, thus improving their incentives and above all aiming to enhance the prospects of their job security when the mining industry is facing challenging times. Taking shortcuts by not fully following the safety regulations or industry best practices are often notable, resulting in the rise of Workers Compensation Board claims and temporary shutdowns of active workings, compromising productivity and increasing the operating costs.In accordance with the Mines regulations in various jurisdictions in Canada and the US, it is evident that companies adhere to establishing basic ventilation management systems through the provision of the code of practice, procedures, work practices and standards/guidelines. This is aimed at ensuring the health and safety of underground workers (de Souza, 2017). However, the challenge to many operations is the improper implementation of the mine ventilation regulations including some managers showing reckless disregard for workers safety by focusing on production and not worrying to address ventilation problems (Steven & O'Keefe, 2010). Other challenges facing effective ventilation management include inadequate training of frontline workers on ventilation system and hazards associated with poor ventilation systems such as toxic gases, dust, heat, and underground explosions (Mufson et al., 2010; Suvar et al., 2017); friction between mine managers and the mine inspectors (Mufson et al., 2010), improper maintenance of ventilation system and inventory management, among others."

Jan 1, 2019

By M. J. Kovalik

Lower Sunnyside seam coal from Utah was blended with various proportions of char and high-temperature coke to improve the quality of the coke obtained from carbonizing this coal. The Hanson 5-pound carbonizer was used as a "screening test" for the larger scale Bureau of Mines-American Gas Association (BM-AGA) tests, which were correlated with industrial production. Eighteen carbonization tests were made in the BM-AGA 13-inch retort, with a coal charge of about 90 pounds; the cokes were evaluated by the standard ASTM tumbler test. Carbonization of blends containing char and coke breeze yielded less fissured and blockier cokes of significantly higher ASTM I-inch tumbler indices as compared with the value for the straight Sunnyside coal. It was found that the simultaneous addition of char and coke breeze yielded stronger cokes than that obtained by the addition of either one of these additives. Addition of a small proportion of Pocahontas No. 3 or Sewell coal to an optimum blend improved the resulting coke strength further.

Jan 1, 1969

By Andrew St. Amant

This report reviews the first three "investigative and concept generation" phases of the referenced contract, and details task performance of Phase IV. This last phase integrated the most promising concepts from Phases I, II, and III into a prototype detailed design which was manufactured, and then tested on a mine locomotive. The concepts developed during the first three phases provided "Improved Pole Tracking," automatic "Rapid Pole Retraction" in the event of dewirement, and servo-operated "Remote Pole Repositioning" on the trolley wire. The Appendix of this report supplies detailed information for the design and construction of the prototype system which is comprised of an RCB (Remotely Controlled Base subassembly), an RCL (Remote Control Lever subassembly) and an SAU (Servo Amplifier Unit) subassembly.

Jan 1, 1980

By Andrew W. Jenike

There used to be a time when bins were designed for total volume and placed in any available place of the plant. Poke holes were provided and feed was maintained by manual prodding, lancing, hammering, and by various mechanical flow-profiting devices. Little thought was given to what occurred inside the bins and why materials did not flow. Indeed, such mental effort was hard to justify while low-cost manual labor was plentiful, quality standards low, and rates of feed moderate. The past fifteen years have seen a drastic change in these conditions. We all know that labor for hard manual work is becoming unavailable at any wage, level. Standards of product uniformity are continuously rising. This uniformity is just as important in a fine ore feed to ball mills as it is in a cattle feed or in a flour mix. Rates of feed now frequently exceed 2,000 tons per hour per feeder. At that rate there is no time for, lancing or prodding. An efficient storage, plant contains a known available volume of bulk solid, and feeds it at the required time, at the prescribed rate, and without degradation of the product. A storage bin may also perform other functions such as blending of different grades, degasification of aerated, powders, isolation of different gaseous media. A contact bed of particles flowing by gravity in counter-current with a gas or liquid may be used as a continuous reactor. Gas or liquid pressures can be simply contained by, a sufficient head of flowing solid.

Jan 1, 1968