Search Documents

By Wendell L. Reich

Percussion drilling dates back to the hand operated star drill and hammer. Eventually steam and compressed air were substituted for muscle power and the mechanical percussion drill was born. From the hand held jack hammers, driving a forged steel bit into the rock, there evolved the jack leg, the rubber tired and crawler mounted drill carrier with automatic feed, increasing power and reducing man?s muscle requirements. Because the reaction of a blow on one end of a piece of steel has to be transmitted to the other end there is a limit to the depth or length of drill steel that can economically be used in out of the hole percussion devices. During the late 1800?s there is evidence that designers were attempting to put the percussion tool at the bottom of the hole, directly on the bit, in order to avoid the long drill steel which absorbed much of the blow, leaving little to be applied to the bit and the rock being drilled.

Jan 1, 1972

By V. V. Getman, V. A. Chanturiya, T. N. Matveeva

Most of the Au and PGM ores in Russia are characterised by a thin mineral impregnation of noble metals in sulfide minerals, and a large variety of mineral forms that lead to high loss of precious metals with fine fractions during flotation. In modern flotation technology, the rational choice of reagents is one of the main trends for selective separation of minerals and effective metals recovery. New data on the selectivity of the thermo-sensitive polymer with specific functional groups (TMPPh) as a flocculant and collector of Au and Pt fine fractions are available. The selective modified collector (DEDTCm) for the recovery of Au and Pt from complex ores is discussed in this paper. Scanning electronic microscopy (SEAM), laser SIM and AFM microscopy, UV and IR spectroscopy were applied to study the adsorbed layer of new reagents on the mineral surface. Flotation tests of TMPPh on the gold-bearing ore of the Olimpiada deposit showed an increase in Au extraction and Au content in the concentrate of the rougher flotation. Using a combination of reagents TMPPh and ButX, the quality of the Au and Pt concentrates increased in 1.7 time with an increase in recovery up to 15 % compared with the traditional reagent mode. Testing of TMPPh polymers in flotation of Pt-Cu-Ni ore at Norilsk Nickel has shown the ability to obtain a concentrate with a higher Pt content. Recovery of platinum is 17% higher than recovery in an experiment without polymer. Application of DEDTCm helped to achieve higher technological parameters in flotation of lowgrade Rt-Cu-Ni ore. Compared to the basic mode Pt recovery was plus 13%, Pd recovery was plus 9% and the content of precious metals in the rougher flotation concentrate increased in 2,5 - 4 times. The studies have been supported by Grants of the President of RF “Scientific School of Academician V.A. Chanturiya” NSh-220.2012.5, NSh-748.2014.5. Keywords: Au and Pt complex ores, flotation, flocculation, thermo-sensitive polymer TMPPh, modified collector

Jan 1, 2020

By Andrew W. Jenike

There used to be a time when bins were designed for total volume and placed in any available place of the plant. Poke holes were provided and feed was maintained by manual prodding, lancing, hammering, and by various mechanical flow-profiting devices. Little thought was given to what occurred inside the bins and why materials did not flow. Indeed, such mental effort was hard to justify while low-cost manual labor was plentiful, quality standards low, and rates of feed moderate. The past fifteen years have seen a drastic change in these conditions. We all know that labor for hard manual work is becoming unavailable at any wage, level. Standards of product uniformity are continuously rising. This uniformity is just as important in a fine ore feed to ball mills as it is in a cattle feed or in a flour mix. Rates of feed now frequently exceed 2,000 tons per hour per feeder. At that rate there is no time for, lancing or prodding. An efficient storage, plant contains a known available volume of bulk solid, and feeds it at the required time, at the prescribed rate, and without degradation of the product. A storage bin may also perform other functions such as blending of different grades, degasification of aerated, powders, isolation of different gaseous media. A contact bed of particles flowing by gravity in counter-current with a gas or liquid may be used as a continuous reactor. Gas or liquid pressures can be simply contained by, a sufficient head of flowing solid.

Jan 1, 1968

By Milton Williams

A comparison is made between the amount of interstitial water found by analysis in cores and that estimated from the resistivity curve of the electric log for the corresponding strata of producing reservoirs. It is shown that while the determined and the estimated water saturations are in good agreement in some cases, this agreement may be due to a fortuitous compensation of errors. Estimates of water saturations made from the electric 1og by use of existing relations should, therefore, be employed with caution. Also presented are data on the variation of salinity of interstitial waters in reservoir sands, and on the effect of variation of salinity and porosity on the validity of estimates of water content made from the electric log. INTRODUCTION Throughout the history of electric logging there have been recurrent cycles of optimism and pessimism as to the value of the electric log in the quantitative estimation of reservoir fluid content. The very early days of electric logging were an optimistic period, in which there was widespread faith in the ability of the resistivity curve to reflect fluid content, and in the ability of the potential curve to indicate textural characteristics. In time the accumulation of exceptions to this idealistic behavior brought about a general disillusionment, and caused the more pessimistic of those dealing with electric logs to believe that the sole importance of the log lay in stratigraphic correlation. Within the last several years optimism as to the quantitative use of the electric log has been revived, primarily as the result of the stimulating work of C. E. Archie' on the estimation of interstitial water in sands from resistivity data. Even though the general trend of thought on the quantitative value of the electric log reflects optimism, it is inevitable that there are some widely divergent opinions of the validity of quantitative estimates based on the electric log. A valid method of estimation of fluid content by means of the electric log and a general knowledge of the textural character of the reservoir rock would be of signal importance, not only in that it would save time and money in securing information on reservoirs now being drilled, but also because it would permit the evaluation of reserves in many fields drilled without adequate core data subsequent to the advent of electric logging. Because of this importance, Humble's Production Research Division, in cooperation with various other company divisions, initiated several years ago series of tests designed to evaluate the reliability of estimates of fluid content made from the electric log. The investigation was limited at the outset to sand reservoirs, since it was felt that the inclusion of limestone reservoirs would entail needless complications. In devising these tests it was immediately apparent that the chief difficulty in evaluating the worth of any method of estimation lay in establishing the true value of fluid content. The results of direct analyses of cores cut with ordinary mud were not sufficient, because of the probability of contamination of the fluids by filtrate from the drilling mud; the results of restored state tests on cores were deemed unsuitable because these results can hardly be said to furnish a primary standard. The method adopted was the direct analysis of cores cut with an oil-base drilling fluid. Such cores, when properly handled, are believed to afford the most precise determination of water content available at the present, and, in addition, lend themselves readily to the determination of various other properties which are pertinent to the estimation of fluid content from the electric log. Since it was desired to compare the fluid contents estimated from the electric log run in ordinary mud with cores cut in the same hole, the use of oil-base fluid necessitated the changing over, after all cores were cut, to a conventional mud. This procedure presented several advantages, one of which was that the use of oil-base fluid permitted

Jan 1, 1950

By T. A. Rickard

The dictionary defines 'jargon' as "barbarous or debased language". This description does not suffice. Quiller-Couch has said, it is "a kind of writing which, from a superficial likeness, commonly passes for prose in these days, and by lazy folk is commonly written for prose, yet actually is not prose at all ". The two main vices of jargon, he says, are "that it uses circumlocution rather than short straight speech", like the Babu who reported his mother's death by saying: "Regret to inform you, the hand that rocked the cradle has kicked the bucket ". Its other chief' vice is that "it habitually chooses vague woolly abstract nouns rather than concrete ones", like the newspaper statement; "He was conveyed to his place of residence in an intoxicated condition", instead of saying, "He was carried home drunk ". Jargon is "an infirmity of speech", it is not journalese, but akin to it. "Like respect- ability in Chicago, jargo4 stalks unchecked in our midst" and renders much technical writing ridiculous. It deals in periphrasis instead of going straight to the point, it loves the abstract rather than the concrete, it dabbles in words of sound rather than of meaning. Avoid it, despise it., if you purpose earnestly to write well. "III literature as in life he makes himself felt who not only calls 4 spade a spade but has the pluck to double spades and re-double." * Jargon is rampant in technical publications. Catalogues and other advertisements are conspicuous offenders, but with these the critic is not concerned, except in so far as such 'write-

Jan 1, 1931

By Q. H. Liao, B. G. Monaghan

The options for designing slopes in complex geological conditions are reviewed. It is shown that modelling, especially numerical modelling, allows a degree of analysis that cannot otherwise be achieved. Examples are presented of how numerical modelling can be used to investigate fundamental aspects of rock mass behaviour. It is demonstrated that an important consequence of change in scale is that the mechanisms of failure also change. The complex failure of the footwall slope at Aznalcollar, a large open-pit mine in southern Spain, is discussed. Numerical modelling with UDEC (universal distinct-element code) has allowed the realistic simulation of displacements measured in the field

Jun 18, 1905

By N. A. Barcza

DC plasma-arc technology using a hollow graphite electrode (cathode) has been successfully implemented in the primary metallurgical industry in South Africa up to the 30 MW scale. Mintek has applied its expertise base, established over the past fifteen years, to testing the treatment of metallurgical wastes such as carbon- and stainless-steel plant dusts, lead- and zinc-containing slags, and residues from the base-metal industry. Favourable results have been achieved, and disposable products were produced. The evaluation of numerous wastes indicates that recovery of zinc as metal gives the best economic return from these sources. Direct recovery via a splash condenser or electrolytic zinc extraction from fume are the two preferred alternatives under review. In both instances dehalogenation is an important issue, but can be achieved by suitable treatment processes. The Enviroplas technology provides a flexible, commercially viable approach to the treatment of a wide variety of wastes. Mintek, together with its associate Pyromet CC, are installing a plasma- arc pilot-plant facility with both an ISP lead-splash condenser of about 5 t/d condensed zinc capacity and a combustion chamber to burn zinc vapour to zinc oxide. This will demonstrate the suitability of the Enviroplas technology for treating specific metallurgical wastes, so that customized industrial plants can be engineered based on large-scale testwork.

Jan 1, 1994

By D. Mireku-Gyimah, R. S. Suglo

Ghana contains auriferous belts which cover 51 800 km2 of its small area of 239 400 km2. From 1493 to 1600 35.5% of the world gold production was from the Gold Coast (renamed Ghana in 1957). This dropped to 8.9% from 1701-1800. For the past fifteen years annual production has averaged less than 2% of the world total. By 1985 only four gold mines were operating, compared with 45 in 1934 and 11 in 1945. Since 1987 Ghana has experienced a boom in gold mining activities. By 1991, 83 new companies had acquired prospecting licences. At least five new companies have started large-scale production. About 650 licensed small-scale mining groups are in operation. The economic and technological factors that have contributed to the decline of gold production in Ghana are discussed. A summary is given of the methods used to mine and recover gold. These cover small-scale workings, dredging, open cast operations and underground mining. The advantages and disadvantages of these technologies and the future of gold mining in Ghana are considered.

Jan 4, 1993

By D. Moses, J. A. Onyango

Carbonatites are generally competent rock masses with rock mass rating class II rating 60–74. In spite of their competency, they tend to be affected by weak features like manganese-iron veins and/or in situ rock damage due to brecciation associated with carbonatite complexes. Rock slope failure in such hard rocks is complex since such structures within the rock mass form weak links that could potentially control slope instability. In this contribution, a numerical simulation using phase2 v 7.0 was carried out to investigate the influence of in situ rock damage on the stability of mine pit walls. The outcome reveals that, the existence of breccia in the competent rock mass has the capability to reduce the slope stability performance particularly at gentle dipping angles of emplacement in close range to the slope toe. However, as the emplacement position of breccia moves away from the pit wall, the stability performance increases at gentle dipping angle <50º. On the contrary, at the dipping angle of 50° the performance of slope reduced, and at steeper angles >50° the impact becomes negligible. Thus, from a series of analyses, mine design in brecciated rock masses, the ratio of 1:5 between the breccia distance from slope toe and pit depth should be implemented to counter its impact, and if the breccia is within or close to the pit limit, a deliberate effort must be made to mine it out.

Sep 1, 2025

This report summarizes the cost of U.S, mining and milling industry compliance with the Environmental Protection Agency (EPA) interim water quality guidelines for waste discharges. Applicable excerpts from Public Law 92-500 are stated and interpreted in conjunction with the guidelines being used for implementation of the law. Over 200 U.S. Army Corps of Engineers applications for discharge permits were used to develop the quality and quantity data base needed to estimate the cost to comply with EPA guidelines, Cost of three basic treatment methods were considered: Aeration, addition of lime, and sedimentation. From the process design, cost-capacity graphs were developed to consider maximum flow rate, maxi lime addition, and average flow rates. The graphical method used in this evaluation should provide a reasonable guide to the effect of waste treatment and, therefore, Public Law 92-500 and corresponding EPA guidelines on the mineral processing industry. The cost of complying with the EPA guidelines will have the effect of prompting the mining industry to minimize the production of waste water and of undertaking some additional treatment, Two case studies are presented to illustrate efforts that might be fruitful for minimizing waste water production and for treatment of combinations of acid mine drainage, mill wastes, and metallurgical process wastes when treatment is deemed necessary.

Jan 1, 1975

By Sam Tour

OF the new alloys achieving commercial prominence during the year, an aluminum-silicon magnesium casting alloy, which is similar in many respects to the 4 per cent copper alloy, developed about 1921, which has attained such a wide field of service, may be mentioned. The new alloy, like the old, is a heat-treatable type and develops about the same physical properties. The alloy casts easily and is relatively insensitive to high pouring temperatures. Its ability to produce substantially leak- proof castings is noteworthy. A second casting alloy development is the new Aluminum Co. of America No. 132, "Lo-Ex" piston alloy, a result of nearly eight years of research. The alloy contains about 14 per cent silicon and varying amounts of nickel, copper, and magnesium. It exhibits a low coefficient of expansion and thus permits small piston clearances. Its lower specific gravity is a further advantage.

Jan 1, 1932

By W. S. Landers

This report presents a study by the Federal Bureau of Mines of technical factors related to the production of special carbon and tar from selected Wyoming coals. Certain Wyoming high-volatile bituminous and subbituminous coals were processed in bench-scale apparatus to determine potential carbonization yields and in pilot plant retorts to produce sufficient char and tar for testing. These tests have shown that a critical selection of coal is necessary when the coal is processed for a specialized carbon. Generally high yields of tar are obtained from low-temperature carbonization of Wyoming high-volatile bituminous and subbituminous coals, and the yield of tar usually increases with increase in rank within this range of coals. The production and evaluation of industrial carbons from Wyoming coals by using pilot plant and bench-scale techniques is part of the continuous program of upgrading western coals. It has been found that: 1. Most Wyoming coals are nonagglomerating and may be carbonized in fluidized systems. Chars produced in pilot plant retorts at low temperatures contain about 17 to 23 pct, residual volatile matter and are easily ignited. These chars appear suitable as power plant fuel. The tar-plus-light-oil yields range from 14 to 40 gal./ton of raw coal processed. 2. Wyoming high-volatile coals produce a slightly smaller and somewhat weaker coke than currently mined Western United States high-volatile coals used commercially as blending stock in metallurgical coke production.

Jan 1, 1961

By Oliver C. Ralston, and others

"INTRODUCTION Investigations of the Nonmetals Division are now conducted at College Park, Md.; Tuscaloosa. Ala.; Seattle, Wash.; and. Norris, Tenn. The last of these was acquired, this year by arrangement with the Tennessee Valley Authority and is engaged in electrothermel research, using power generated by the T.V.A. and. raw materials from that region. In general, the work of the division is concerned with dressing nonmetallic minerals end utilizing the products there-from. Coal, salts, and waters are investigated, and the suitability of apparatus and equipment is studied.As the Metallurgical. Division of the Bureau of Mines makes routine tests of certain nonmetallic ores under prescribed conditions for the public if they are of general interest, the published reports of that division should be read and thus, with the reports of tile Nonmetals Division, the whole field may be covered."

Oct 1, 1939

By Akira Kaneda, Nozomu Hasegawa

"In the Mitsubishi Continuous Copper Smelting and Converting Process, slag/matte mixture overflowed from the smelting furnace is separated continuously in an electric furnace (slag cleaning furnace, CL-furnace). In order to improve the separation efficiency of slag and matte and to minimize power consumption, the design and the operating conditions of the CL-fumace should be optimized. In the previous study, the authors developed a mathematical model for simulating phenomena in the CL-furnace. The model consisted of 3 modules, electric field analysis, heat and fluid flow analysis and the particle tracking method. In this study, the model was partially modified: k -E. model was adopted, and the effects of various conditions, such as furnace shape (including accretion) and scale, electrodes configuration, immersion depth of electrodes, and thickness of slag layer, were evaluated. And the optimum design and operating conditions were discussed.IntroductionUnder the recent environmental restriction, advantageous features of the Mitsubishi process have attracted much attention. The process uses 3 furnaces connected by launders. Mixture of matte and slag formed in a smelting furnace flows continuously to a slag cleaning furnace (CL-furnace), where the matte is separated from the slag. The matte is continuously siphoned out to a converting furnace and converted to blister copper. The slag overflowed from the CL-furnace is discarded. Because the slag contains about 0.6 % copper, improving slag/matte separation efficiency and decreasing copper loss make a great profit. Moreover the process requires a large amount of electric energy, so reduction of electric power consumption brings in enormous benefit.The objective of this study is to optimize the design and the operating conditions of the process, especially the CL-furnace. This will be achieved by developing the mathematical model and clarifying relations between the design or the operating conditions and various phenomena in the furnace. Fig. 1 shows an outline of the CL-furnace. The mixture entering through an inlet is separated to slag layer and matte layer . In order to maintain the temperature of the melt at a predetermined level, 6 electrodes are immersed into the lag and Joule's heat is generated by 3-phase alternating current flowing."

Jan 1, 2000

By Robert C. Ellman

The Bureau of Mines investigated the factors that cause agglomeration of lignite by freezing during winter shipment and sought methods to avoid it. Tests showed that lignite may be freezeproofed by removal of the relatively small quantity of moisture involved in forming the frost crystals which cement particles together, or by controlling the crystal characteristics. Adding dried lignite fines proved to be an effective and superior freezeproofing method. Commercial adoption of this method has been successful.

Jan 1, 1965

By Paul W. Johnson, Ralph C. Kirby, Frank A. Peters

An evaluation is presented for a process designed , on the basis of published work , to extract alumina as potassium alum from clay using sulfuric acid and potassium sulfate . The silica residue is separated by filtration . Ferric iron is reduced to ferrous iron , and the alum is crystallized from the solution , leaving the ferrous iron in solution . The alum crystals are separated from the solution and redissolved for feed to autoclave decomposition . In an autoclave the alum is partly decomposed to a basic alum , recovering five - ninths of the sulfuric acid and two - thirds of the potassium sulfate without using an acid plant . The basic alum is decomposed by calcining , and the potassium sulfate is then removed by washing with water . Operating costs for a plant producing 1,000 tons of alumina a day are estimated at $ 96.15 per ton of alumina . The fixed capital cost is estimated at $ 155 million . This process is not competitive under current economic conditions with the production of alumina from bauxite by the Bayer process . Improvement in leaching , basic alum decomposition , and washing could reduce the costs and improve the product which contains some potassium .

Jan 1, 1963

By John K. Alley, Robert C. Johnson

The primary objective of the research was to grow aluminum borate whiskers or fibers and to determine their properties . Molten salt bath and vapor deposition methods were used for synthesis . Whiskers exceeding 25 mm in length were grown . The best results were obtained by vapor deposition and most of the data presented were determined on whiskers produced by this method of synthesis . Three different aluminum borate compositions ( 4.8A1203 B₂03 , 3.8A1203 B203 , and 2.5A120, B203 ) were identified by X- ray and chemical analyses . The aluminum borates 4.8A1203 B20, X- ray diffraction pattern was indexed . Optical data were obtained on the three aluminum borates . In addition the following whisker properties and growth factors were determined : ideal atmospheric dewpoint for vapor deposition method , near 65 ° F ; temperature range of whisker formation , 1,000 ° to 1,400 ° C for the molten bath method of synthesis , > 1,000 ° to < 1,400 ° C for the vapor deposition method ; whisker growth rates by the vapor deposition method , maximum 12 mm per hour ; raw material vaporization , 50 to 60 percent of the fluoride lost in 1 hour ; tensile strength , maximum obtained 174,162 psi ; melting points , ranged from 1,675 ° to 1,795 ° C.

Jan 1, 1965

By R. Gorakhki, R. Stafford, A. Jung

Geosynthetic clay liners (GCLs) have been used widely as an alternative for compacted clay liners and covers in mine waste applications. The high swelling of bentonite particles in the GCL creates a uniform barrier layer that results in low permeability of water and mine waste leachate. GCLs must provide sufficient internal and interface shear strength stability, especially if GCLs are used in steep slopes under high normal loads. Peel strength is a common parameter that is typically correlated to internal shear strength properties of GCLs. The relationship between internal shear strength and peel strength of GCL at normal stresses of 287, 575, 862, and 1724 kPa is evaluated in this study. The data in this study was compared with the peel strength-internal shear strength relationships found in literature. The study concludes that the relationship between peel strength and internal shear strength is unique based on manufacturing, needle-punching density and the method with and without heat treatment of the geotextile end fiber bundles.

Feb 1, 2023

By H. P. Wang, E. M. Perry

"Analytical solutions for investigating the solidification of casting problems with initial superheat and natural boundary conditions have been derived using an integral method. There are two moving interfaces in the solution field, one for the phase change line and the other for the superheat line. Two coupled nonlinear differential equations, representing two moving layers, were calculated by the Runge-Kutta numerical integration scheme. The solutions are in terms of six dimensionless parameters: phase change number, two Biot numbers for interfaces, diffusivity ratio, and dimensionless superheat temperature and time. Parametric studies on these parameters have been conducted to provide generic information about this phase change problem. This analytical information is extremely useful for validating numerical solutions. A simplified I-D finite element model was constructed for the purpose of comparison. The excellent agreement between the analytical and finite element solutions has proven that they are mutually validated.This validated finite element modeling tool was then used for modeling an investment casting process of a super-alloy with a simple geometry: a two-step plate. The nonlinear latent heat release, a common property of alloy materials, was approximated by several piecewise linear segments. The transient temperature response of this 2-D finite element solution, including a metal/mold gap resistance, shows excellent agreement with experimental data.This fundamental work provides a solid basis for further work on the development of a process modeling tool for the complex investment casting process.IntroductionAt present, the investment casting process is used in a variety of industries. In the aircraft engine industry, in particular, investment casting is used to produce parts ranging from turbine blades to engine frames. Because a large single casting can replace many component parts that require machining, fabrication, and assembly, this one-piece casting approach becomes a very cost-effective manufacturing process.The main constraint in using this process for mass production is the long design-to-production lead time. The standard rigging design is still an art, based on the experience of casting experts, rather than on scientific methods. Many trials are often required before making a sound final casting. In order to .reduce the number of expensive casting trials, the development of computer-aided tooling technology is needed.The fundamental physics describing this manufacturing process can be simply described. They reduce to a solid/liquid phase change problem, with two parts - first, the thermal balance of the initial superheat temperature of the molten metal and the preheat temperature of the ceramic shell through heat conduction, and second, the energy release from the mold surface to the ambient by radiation."

Jan 1, 1986

By James P. Bennett

In this Bureau of Mines study, portions of four acidproof bricks (two red shale and two fireclay) were exposed to 20 wt pct RCI at 900 C for periods of 30 days. Three different techniques were selected to deter-mine volume expansion of these materials after exposure. Linear expansions ranging from about 0.02 to 0.12 pct were noted from Ta pin and dilatometer measurements. The use of strain gages to measure expansions was not successful. The red shale and fireclay brick with the lowest apparent porosities had the lowest expansions. Expansion data obtained by direct measurement of samples exposed for 30-day periods or by dilatometric measurement of autoclaved samples ex-posed for 2 h were comparable. This suggests the use of an accelerated autoclave exposure procedure for determining volume expansion effects of ceramic materials in acid environments.

Jan 1, 1985