Search Documents

By Allan G. Provost

Shaft construction is assuming ever increasing importance when new mining enterprises are considered. The reasons for this increased emphasis is the much greater depths at which many new ore-bodies are being developed and the rapid depletion of near surface reserves requiring mines to go to greater depths on existing deposits. These greater depths increase the probability of exposure to unfavorable geologic conditions and it is more likely that high ground and/or water pressures will be experienced at these depths. The large capital costs involved and the critical position of a shaft in the overall mining program necessitate that this element of project development be given careful and critical consideration. The Henderson No. 2 Shaft is located in the Rocky Mountains of north central Colorado (See Figure I), about 55 miles west of Denver, near the community of Empire in Clear Creek County. At the 10, 442 foot collar elevation, winter arrives in late September and brings snow to contend with until May. The labor force for Shaft No. 2 is approximately 90 men. They are provided access to the project via all-weather U. S. Highway 40. SHAFT DESIGN The Henderson No. 2 Shaft is a 28-foot I. D. circular, concrete lined (1 foot thick) vertical shaft. The final depth will be approximately 3100 feet

Jan 1, 1972

By C Gimber

Dust suppression is an important environmental control in most mining operations. The poorest quality water within a mine site is often used for dust suppression since it provides an effective means of reducing the volume of poor quality water. The ultimate fate of contaminants or salinity associated with water used in dust suppression is important to consider for optimising water management and assessing the environmental impact and life span and maintenance requirements of roads associated with dust suppression.The propensity for remobilisation of contaminants or salts depends on a range of factors such as the application rate, climate, road construction, water chemistry and soil geochemistry. This paper describes a typical study approach which could be used to assess the short- and long-term impacts of mine water application for dust suppression. The steps of the study are: reviewing the environmental setting, estimating water requirements for dust suppression, reviewing source water chemistry, developing a mass balance model and assessing the mobility and fate of contaminants with a geochemical model.This approach identifies which salt species are likely to form and whether they are prone to remobilisation. It is possible to quantitatively assess the risk of exporting contaminants or salt from roads and to refine the dust suppression strategy to minimise the environmental risk. The approach can be applied at mine sites to address regulator concerns, aid decision-making and improve the understanding of short- and long-term environmental risks.CITATION:Gimber, C, 2013. Assessing contaminant risk associated with the use of mine water for dust suppression, in Proceedings Water in Mining 2013 , pp 235-240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By A. A. McDonald

Anode casting has been in operation for two years in Hudson Bay Mining and Smelting's Flin Flon smelter. The new plant allows all casting to be done on one shift and so achieves considerable labour savings. The equipment and operations are described. Some important features are as follows: very consistent anode weights by the use of the load-cell controlled casting ladle; excellent mould life ; very low reject rate; and trouble-free take -off tower. Some of the start-up problems are described and an outline is given of the main operator functions. Data on labour, propane and maintenance costs are presented.

Jan 1, 1977

By Martin H. Stanczyk

The Organic Act of 1910 established the Bureau of Mines and gave it authority and responsibility for conducting research on separation, recovery, and recycling of waste products and scrap generated by the mineral and metals industries and the consuming public.(1)1 It was apparent to our Nation's leaders even then that mineral resources, once mined, are irreplaceable and that the development of methods for recycling the values contained in wastes would be required to solve the problem of even¬tual scarcity, Estimates of the increase in per capita consumption of mineral resources in this country indicate that the consumption of metals, minerals, and fossil fuels by 1980 will be double that consumed in 1970 (2). The United States can expect to meet its future mineral needs in three basic ways: the first is through increased production of primary raw minerals; second by increasing imports from foreign sources; and third by recycling secondary materials and metals that were formerly discarded as waste. Rather than consider these

Jan 1, 1972

By C Robertson, J Campos

The South African mining industry first experienced en-masse use of electronic detonators in the Narrow Reef environment using AELÆs ElectrodetÖ pre-set delay system. In recent years, programmable systems such as AELÆs SmartdetÖ have also established their position, and within both AEL and the mines there has been important learning around the strengths and weaknesses of these systems. In general, the fixed delay systems tend to be more easily appreciated by less-skilled work teams, and are very well suited to simple layouts, especially long, narrow blasts. However, development of programmable row controllers and series delay inserts has greatly expanded the field of usefulness of these systems while retaining most of the simplicity of use. The programmable systems are immensely flexible and therefore able to function under any condition, but require a higher level of discipline and knowledge. Much has been done to address this issue and make the systems user friendly, so the systems have converged to some extent. These systems are both valuable tools for achieving control over blasting in underground and surface applications. The choice of system is very dependent on the prevailing conditions. Accurate timing with electronic enhancements continues to show an increasing range of benefits to mining operations. There is a strong parallel with non electronic initiation systems which helps to understand the appropriate use of the systems.

Jan 1, 2001

By P. A. Peach, W. H. Gross

The modern economic geologist in Canada is well equipped to apply geological, geochemical or geophysical techniques in the exploration for ore. Recently, great advances have been made in geophysics and geochemistry, and a large number of new orebodies have been discovered by these methods. An attempt is made in this paper to show that there has also been a considerable advancement in geological knowledge and that the most effective application of geophysics and geochemistry often occurs in areas already considered geologically favourable for the occurrence of ore. Ali exploration methods sooner or later suffer from diminishing returns. Therefore, as time goes on, one can expect to see the application of some of the more subtle or refined geological techniques that are presently being developed.

Jan 1, 1967

By E. DeLilia

For the past 30 years, surface mines have moved toward more highly mechanized, automatic systems that continuously mine overburden and ore to in-crease productivity, lower operating costs and minimize manpower needs. To achieve these goals, mine operators must be involved in every step of the machine procurement process. Several factors are involved in making the machines operate economically and efficiently: ? Prudent engineering. ? Proper planning. ? Realistic feasibility studies. ? Effective specification. ? Thorough training of the mine personnel.

Jan 1, 1995

By M. H. Kline, Wing G. Agew

"INTRODUCTION The Watson tract was first prospected in 1908, and ore consisting of concretionary psilomelane and wad was found in the bedded residual clays. A small mill using a log washer and jigs was constructed for concentrating the ores -on the bank of Mudhole Run, and it is reported that a few wagon¬loads of ore were shipped via the Norfolk & Western Railway. The operation was of short duration.During World War I, the area was seriously studied by the Federal Geological Survey and Virginia Geological Survey. The Virginia Geological Survey, in Bulletin 173/ reporting the work, lists the property among the few recommended for further exploration.When the shortage of manganese ores in the United States became imminent, the Bureau of Mines was authorized by the 76th Congress, under the Strategic Materials Act, to prospect and explore for manganese. Upon the recommendation of the Federal Geological Survey, a project to undertake this work was started at the old Watson mine in January 1941 and continued until August of the same year."

Apr 1, 1948

By W. S. Szolga, M. Moser, M. D. Soderstrom, L. Cohen

"CYANEX® 272 is a phosphinic acid-based solvent extraction reagent used commercially since the early 80’s to recover and purify cobalt from sulfate solutions. Historically, the design of CYANEX 272 circuits has involved the selection of an optimal pH profile during pilot-scale testing using mixbox pH control. The desired pH profile is required to be carefully controlled in the same manner during commercial operation. To assist operators in the design and optimization of their circuits, Solvay developed CYANEX 272-specific solvent extraction modeling software, which has enabled determination of the ideal pH profile and staging configuration. Solvay’s recent advances in modeling capabilities have allowed the simulation of circuits without direct mixbox pH control. Modeling has indicated that circuits operated without direct pH control can achieve the desired metal separation while simplifying the commercial operation significantly. This paper reviews a number of potential circuit configurations for the use of CYANEX 272 and demonstrates the separations achievable under the right design and operational conditions, some of which have historically been considered too difficult.INTRODUCTION CYANEX® 272 is a phosphinic-acid based reagent designed specifically for the separation of cobalt from nickel by solvent extraction from weakly acidic sulfate solutions (Rickelton, Robertson, & Burley, 1982; Rickelton, Flett, & West, 1984; Rickelton & Nucciarone, 1997). Following commercial introduction in the 1980’s, CYANEX 272 has been used in a number of hydrometallurgical flowsheets for cobalt purification and/or recovery. CYANEX 272 metal extraction occurs by means of a cation exchange mechanism. Extraction of a divalent metal ion M2+ is represented by the following equation where RH represents the CYANEX 272 ligand and MR2 represents the ligand-metal complex."

Jan 1, 2017

By Tapani Järvinen

Non-ferrous metals and metals in general are considered as being non-renewable natural resources. Metals are needed because of their excellent and irreplaceable properties. The consumption of metals, with the exception of carbon steel, is steadily growing by 1-3 % annually, and that of stainless steel as much as 3-6 %. This is a general trend, which is periodically disturbed by cyclical variations. In recent years so-called "New Economy" has become prominent in the public media and the market value of the traditional industry has been well below its real value and importance. Nevertheless, the modem society requires metals today and also in the future, and the companies using the most modem technology in a responsible way and innovative solutions not only in technology, but also in everything they do will survive. This paper describes the role of Europe as a producer of primary base metals and as a supplier of technologies in the base metals industry. It concentrates on the development and commercialization of technologies and project implementation in the metallurgical industry. As one example of a European approach to these matters the paper presents Outokumpu' s response to the future challenges in the base metals industry. Outokumpu Oyj is one of the leading metals and technology companies in the world of stainless steel, copper, zinc, and sales of technology in metals and minerals businesses. Outokumpu applies its knowledge of metals and processing to generate value for its customers and shareholder. Everything we do, we do in an economically, environmentally and socially responsible way.

Jan 1, 2003

By J Boshoff

The management and operation of tailings storage facilities (TSFs) are often neglected until the process plant has to shut down as a result of this negligence or as a result of a catastrophic failure as was the case during the recent TSF failure in North America.TSFs are often regarded as non-assets and do not receive the attention they deserve in terms of technical expertise and financial provision. A TSF is not a simple structure but a complex and dynamic structure that changes throughout its operational life. The operational life of a TSF is the period in which there is the greatest opportunity for risks to occur. The failure of a TSF is normally not as a result of a single event but as a result of a consequence of events. These events are often not recognised in time due to a number of factors.Process plants and slurry pumping systems are operated at suboptimal conditions in order to maintain throughput. At the same time, the tailings properties are compromised in terms of slurry density and particle size distribution amongst other things. Tailings deposition cycles and drying cycles are not well understood and the tailings management strategy is not well tuned in terms of maximising consolidation and improving in situ densities. Pond control is also neglected. These are aspects that form the keystone to the effective utilisation of available deposition area as well as the frequency and cost of future embankment raises.Apart from operational issues, forward planning in terms of budget requirements, increases in tailings throughput, embankment raises, pipe replacements, etc are normally put on the back burner. Available deposition space at the time seems to render this planning obsolete.The bottom line is that responsible tailings management and proper forward planning can limit liability and reduce the bottom line in terms of cents per ton if correctly implemented by suitably qualified tailings managers and engineers.The aspects that need to be considered as part of responsible tailings management are highlighted in this paper.CITATION:Boshoff, J, 2015. Responsible tailings management, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 317–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By C. J. Pritchard

The Office of Mine Safety and Health Research (OMSHR) investigated ways to increase mine airflow to underground metal/nonmetal (M/NM) mine working areas to improve miners? health and safety. One of those areas is controlled recirculation. Because the quantity of mine air often cannot be increased, reusing part of the ventilating air can be an effective alternative, if implemented properly, until the capacity of the present system is improved. The additional airflow can be used to provide effective dilution of contaminants and higher flow velocities in the underground mine environment. Most applications of controlled recirculation involve taking a portion of the return air and passing it back into the intake to increase the air volume delivered to the desired work areas. OMSHR investigated a Nevada gold mine where shaft rehabilitation was in progress and one of the two main fans was shut down to allow reduced air velocity for safe shaft work. Underground booster fan operating pressures were kept constant to maintain airflow to work areas, inducing controlled recirculation in one work zone. Investigation into system behavior and the effects of recirculation on the working area during times of reduced primary ventilation system airflow would provide additional information on implementation of controlled recirculation into the system and how these events affect M/NM ventilation systems. The National Institute for Occupational Safety and Health monitored the ventilation district when both main fans were operating and another scenario with one of the units turned off for maintenance. Airflow and contaminants were measured to determine the exposure effects of induced recirculation on miner health. Surveys showed that 19% controlled recirculation created no change in the overall district airflow distribution and a small reduction in district fresh air intake. Total dust levels increased only modestly and respirable dust levels were also low. Diesel particulate matter (DPM) levels showed a high increase in district intake mass flow, but minor increases in exposure levels related to the recirculation percentage. Utilization of DPM mass flow rates allows input into ventilation modeling programs to better understand and plan for ventilation changes and district recirculation effects on miners? health.

By D. S. Hines

The purchase of mechanical equipment for mines is not unlike the purchase of other materials or supplies in general principle, but on account of the major part such equipment plays in the operations, and of the fact that life and valuable property are at stake, the matter demands the most careful attention on the part of the purchaser. The problems and difficulties encountered are dealt with below in their sequence in the purchasing procedure. Requisiting Although it is quite a common practice to submit a tentative specification of requirements to recognized manufacturers of equipment- soliciting alternative propositions or recommendations for study in the selection of certain equipment-as a rule the first step in purchasing procedure is the requisition. Primarily, it is the form that carries to the purchasing department the record of equipment wanted. A full and complete description or specification, and accuracy of record, are the important points to be insisted on in a requisition. Too much attention cannot be given to this detail, as this is one of 'the most important phases of purchasing work. Incomplete information, either in specification or detail, leads to delay in handling the requisition, and, if not detected in the purchasing department, may mean receipt of material which cannot be used for the purpose intended. In addition to description of material or equipment to be ordered, the requisition should also show where or what the equipment is for, whether for operating or new work. If for capital account, the number of the authority for expenditure should be given for record and distribution purposes.

Jan 1, 1930

By J. B. Yianatos, F. A. Contreras

Mineral carrying rates across the pulp-froth interface in the range of 1.4-3.2 tph/m2 and bubble surface coverages between 7 and 22 %, have been determined in large rougher flotation cells operated under normal conditions. To evaluate these variables, measurements of bubble size distribution, bubble load and size distribution of particles collected by true flotation, were performed at different concentrators. A model for estimating the bubble surface coverage at the pulp-froth interface level as a function of bubble load, Sauter mean bubble diameter and particle size distribution of the mineral collected by true flotation, was developed. Bubble loadings in the range 24-70 kg/m3, bubble sizes between 1.5 and 3.2 mm and superficial gas rates between 1.2 and 2.0 emfs, were measured in copper rougher flotation cells under normal operating conditions. Estimated bubble surface area fluxes were in the range 31 to 62 cm2/s/cm2- Results of carrying rates and bubble surface coverage, at the pulp-froth interface, were significantly lower than the maximum carrying rate for the collection zone, indicating that in this case is difficult to achieve maximum carrying rate at the pulp-froth interface level. The main constraints regarding carrying capacity limitations are then related to the froth transport characteristics (i.e. cell design, froth residence time, froth stability, froth recovery). Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists ofCIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By Felipe Sepulveda, Edelmira Gálvez, Luis Cisternas

"In mineral processing, the recovery and/or concentration of the value components cannot occur in one operational stage, therefore requiring the use of separation circuits based on several flotation stages. The components to be separated are typically distributed at different concentrations and different particle sizes, resulting in different levels of recovery. Typically, more than one value component must be selectively removed by exploiting the differences in the components’ floatability at different pH values, pulp potential and particle size. Several methods for the design of these circuits are available in the literature, but comparatively few studies present circuit analysis tools or address the design of a multiple-product flotation circuit. In this study, global sensitivity analysis was used to analyze a flotation circuit with several products, such as copper, lead and zinc. This analysis was based on the Eureka mine concentrator plant. The analysis was performed for each of the sections of the circuit as an overall evaluation of the circuit. The Sobol’ method and the correlation method were used to evaluate the Eureka mine concentrator plant using the SimLab 2.2 software."

Jan 1, 2014

By R. Baker

A novel electrochemical half-cell and corresponding working electrode were designed to evaluate the electro-catalytic activities of catalysts in an environment close to that of an operating proton exchange or polymer electrolyte fuel cell (PEMFC). Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) techniques were employed using the novel cell to characterize various methanol electro-oxidation parameters that contribute to the overall reaction on a fuel cell anode. The effect of temperature on methanol oxidation kinetics was examined in the potential range of 0.31 to 0.65V (vs. NHE). The data was collected in the temperature range of 20 to 80°C. Based on the experimental analysis and literature data, an equivalent circuit model (ECM) for methanol oxidation was proposed and was used to fit the EIS experimental data. The experimental data and ECM electrochemical data was used to extract electrochemical kinetic parameters for methanol oxidation such as the exchange current density, Tafel slope, and energy of activation for the reaction. Kinetic data, especially at different temperatures, is very limited in the literature.

Jan 1, 2005

By Weijie Wei, Jinwang Zhang, Jiachen Wang, Yang Li

"Longwall top-coal caving (LTCC) mining technique is one of the important methods for underground thick seam extraction in China. The coal seam in LTCC panel is divided into two parts: bottom-coal and top-coal. The bottom-coal is mined by conventional longwall method while the top-coal is mined by caving method. The top-coal caving process in LTCC and block caving process in metal mine are both gravity flow of loose ore/coal blocks. However, the presence of caving shield in LTCC makes the characteristics of drawing body shape in the two caving processes differ a lot. This paper discusses the influence of caving shields on the characteristics of drawing body shapes in light of recent studies of the top-coal drawing process. The theoretical model for describing the drawing body shape in LTCC is proposed both along the seam strike and seam inclination. Then, the experimental data are used to validate the correctness of the theoretical model. Furthermore, two examples of how the theoretical findings assist LTCC mining are given and discussed.INTRODUCTIONLongwall top-coal caving (LTCC) mining technique and large-cutting-height mining technique have been widely used for extracting thick coal seams in China. About 0.6–0.7 billion metric tons of coal come from longwall top-coal caving panels every year. The maximum annual production is 15 million metric tons per panel _The mining method employed in such panel is a combination of top-coal caving mining technique and large-cutting-height mining technique, which is suitable for seam height between 12–20 m, as shown in Figure 1. Apart from China, LTCC has also been employed in some coal mines in Australia and Vietnam (Le et al., 2017).The coal seam in a LTCC panel is divided into two parts: bottom coal and top coal. The bottom-coal is mined by the conventional longwall method, while the top coal is mined by the caving method. The top-coal caving process in LTCC and block caving process in metal mines are both gravity flows of loose coal/ore blocks, as shown in Figure 2. However, the presence of caving shields in LTCC causes the characteristics of the drawing body shapes in the two caving processes to differ significantly.There are two main differences between the blocking method and the top-coal caving method:"

Jan 1, 2019

By Tapani Järvinen

Non-ferrous metals and metals in general are considered as being non-renewable natural resources. Metals are needed because of their excellent and irreplaceable properties. The consumption of metals, with the exception of carbon steel, is steadily growing by 1-3 % annually, and that of stainless steel as much as 3-6 %. This is a general trend, which is periodically disturbed by cyclical variations. In recent years so-called "New Economy" has become prominent in the public media and the market value of the traditional industry has been well below its real value and importance. Nevertheless, the modem society requires metals today and also in the future, and the companies using the most modern technology in a responsible way and innovative solutions not only in technology, but also in everything they do will survive. This paper describes the role of Europe as a producer of primary base metals and as a supplier of technologies in the base metals industry. It concentrates on the development and commercialization of technologies and project implementation in the metallurgical industry. As one example ofa European approach to these matters the paper presents Outokumpu's response to the future challenges in the base metals industry. Outokumpu Oyj is one of the leading metals and technology companies in the world of stainless steel, copper, zinc, and sales of technology in metals and minerals businesses. Outokumpu applies its knowledge of metals and processing to generate value for its customers and shareholder. Everything we do, we do in an economically, environmentally and socially responsible way.

Jan 1, 2003

By Alfred B. Annor

The introduction and application of paste backfill over the past two decades has resulted in substantial benefits being realised by many backfill reliant mining operations who have used this technology. Paste preparation over this time period has relied basically on mechanical dewatering approaches that have included the use of centrifuges, thickeners, and vacuum and pressure filtration. In large bulk mining operations, this method of paste preparation has usually involved the construction of big and complex surface plants to meet large tonnage demands. These large plants usually have attendant high capital, maintenance and operating costs. The application of paste backfill in narrow-vein mining requires more flexibility in terms of fill preparation, transportation and placement. The method of paste fill preparation should take into consideration low manufacturing and operating costs, ability to use existing facilities at mine sites, simplicity of operation and flexibility of preparing fill over a broad range of consistencies. This paper will review alternative paste fill preparation methods and indicate those that might be better suited to narrow-vein mining.

Oct 1, 2001

By P SSrkkS

Mining is commonly seen as a typical basic industry with rough and even dangerous working conditions, heavy environmental load, and a low level of high-technology and automation with much manual work and operations. A mining operation (open pit or underground) is a very complex one consisting of many manual, physical, mechanical and logistical operations with different human interfaces and decisions. For this reason it is a demanding and potential area for all applications of automation and information technology: controlling difficult non-linear, time varying multivariable processes and machines; solving of ergonomic safety and environmental problems; automation of logistical systems; applying robotics, mechatronics, and information handling, etc. In addition to that, big economic sums are involved with these operations. On the other hand, automation technology has developed towards intelligent and adaptive systems including some from the above mentioned fields of automation. Connecting them with modern information and communication technologies makes the idea of an intelligent and unmanned mine more and more feasible in the near future. This requires intensive co-operation and co-ordination between the mining industry and manufacturers of mining machinery. This has been successfully accomplished in the five-year Intelligent Mine research and development program as well as the three years of subsequent implementation of its results in Finland. The basic elements of an Intelligent MineTM concept are:mine-wide information and data acquisition system; high-speed two-directional mine-wide communication network for real-time monitoring and control; computerised information management, mine planning, control and maintenance systems; automated and tele-operated machinery and equipment which are connected to the information system; and links to the public information networks. The degree of automation of an intelligent mine depends on many technical and economical factors. The basic precondition for such an approach is that it will improve the total economy of the mine. This paper will describe the Intelligent Mine Technology Program with the results. Also the implementation which took place during starting of a new underground mine (Outokumpu Chrome Oy Kemi Mine) will be described.

Jan 1, 2000