Search Documents

By C. J. Pritchard

The Office of Mine Safety and Health Research (OMSHR) investigated ways to increase mine airflow to underground metal/nonmetal (M/NM) mine working areas to improve miners? health and safety. One of those areas is controlled recirculation. Because the quantity of mine air often cannot be increased, reusing part of the ventilating air can be an effective alternative, if implemented properly, until the capacity of the present system is improved. The additional airflow can be used to provide effective dilution of contaminants and higher flow velocities in the underground mine environment. Most applications of controlled recirculation involve taking a portion of the return air and passing it back into the intake to increase the air volume delivered to the desired work areas. OMSHR investigated a Nevada gold mine where shaft rehabilitation was in progress and one of the two main fans was shut down to allow reduced air velocity for safe shaft work. Underground booster fan operating pressures were kept constant to maintain airflow to work areas, inducing controlled recirculation in one work zone. Investigation into system behavior and the effects of recirculation on the working area during times of reduced primary ventilation system airflow would provide additional information on implementation of controlled recirculation into the system and how these events affect M/NM ventilation systems. The National Institute for Occupational Safety and Health monitored the ventilation district when both main fans were operating and another scenario with one of the units turned off for maintenance. Airflow and contaminants were measured to determine the exposure effects of induced recirculation on miner health. Surveys showed that 19% controlled recirculation created no change in the overall district airflow distribution and a small reduction in district fresh air intake. Total dust levels increased only modestly and respirable dust levels were also low. Diesel particulate matter (DPM) levels showed a high increase in district intake mass flow, but minor increases in exposure levels related to the recirculation percentage. Utilization of DPM mass flow rates allows input into ventilation modeling programs to better understand and plan for ventilation changes and district recirculation effects on miners? health.

By D. S. Hines

The purchase of mechanical equipment for mines is not unlike the purchase of other materials or supplies in general principle, but on account of the major part such equipment plays in the operations, and of the fact that life and valuable property are at stake, the matter demands the most careful attention on the part of the purchaser. The problems and difficulties encountered are dealt with below in their sequence in the purchasing procedure. Requisiting Although it is quite a common practice to submit a tentative specification of requirements to recognized manufacturers of equipment- soliciting alternative propositions or recommendations for study in the selection of certain equipment-as a rule the first step in purchasing procedure is the requisition. Primarily, it is the form that carries to the purchasing department the record of equipment wanted. A full and complete description or specification, and accuracy of record, are the important points to be insisted on in a requisition. Too much attention cannot be given to this detail, as this is one of 'the most important phases of purchasing work. Incomplete information, either in specification or detail, leads to delay in handling the requisition, and, if not detected in the purchasing department, may mean receipt of material which cannot be used for the purpose intended. In addition to description of material or equipment to be ordered, the requisition should also show where or what the equipment is for, whether for operating or new work. If for capital account, the number of the authority for expenditure should be given for record and distribution purposes.

Jan 1, 1930

By J. B. Yianatos, F. A. Contreras

Mineral carrying rates across the pulp-froth interface in the range of 1.4-3.2 tph/m2 and bubble surface coverages between 7 and 22 %, have been determined in large rougher flotation cells operated under normal conditions. To evaluate these variables, measurements of bubble size distribution, bubble load and size distribution of particles collected by true flotation, were performed at different concentrators. A model for estimating the bubble surface coverage at the pulp-froth interface level as a function of bubble load, Sauter mean bubble diameter and particle size distribution of the mineral collected by true flotation, was developed. Bubble loadings in the range 24-70 kg/m3, bubble sizes between 1.5 and 3.2 mm and superficial gas rates between 1.2 and 2.0 emfs, were measured in copper rougher flotation cells under normal operating conditions. Estimated bubble surface area fluxes were in the range 31 to 62 cm2/s/cm2- Results of carrying rates and bubble surface coverage, at the pulp-froth interface, were significantly lower than the maximum carrying rate for the collection zone, indicating that in this case is difficult to achieve maximum carrying rate at the pulp-froth interface level. The main constraints regarding carrying capacity limitations are then related to the froth transport characteristics (i.e. cell design, froth residence time, froth stability, froth recovery). Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists ofCIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By Felipe Sepulveda, Edelmira Gálvez, Luis Cisternas

"In mineral processing, the recovery and/or concentration of the value components cannot occur in one operational stage, therefore requiring the use of separation circuits based on several flotation stages. The components to be separated are typically distributed at different concentrations and different particle sizes, resulting in different levels of recovery. Typically, more than one value component must be selectively removed by exploiting the differences in the components’ floatability at different pH values, pulp potential and particle size. Several methods for the design of these circuits are available in the literature, but comparatively few studies present circuit analysis tools or address the design of a multiple-product flotation circuit. In this study, global sensitivity analysis was used to analyze a flotation circuit with several products, such as copper, lead and zinc. This analysis was based on the Eureka mine concentrator plant. The analysis was performed for each of the sections of the circuit as an overall evaluation of the circuit. The Sobol’ method and the correlation method were used to evaluate the Eureka mine concentrator plant using the SimLab 2.2 software."

Jan 1, 2014

By R. Baker

A novel electrochemical half-cell and corresponding working electrode were designed to evaluate the electro-catalytic activities of catalysts in an environment close to that of an operating proton exchange or polymer electrolyte fuel cell (PEMFC). Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) techniques were employed using the novel cell to characterize various methanol electro-oxidation parameters that contribute to the overall reaction on a fuel cell anode. The effect of temperature on methanol oxidation kinetics was examined in the potential range of 0.31 to 0.65V (vs. NHE). The data was collected in the temperature range of 20 to 80°C. Based on the experimental analysis and literature data, an equivalent circuit model (ECM) for methanol oxidation was proposed and was used to fit the EIS experimental data. The experimental data and ECM electrochemical data was used to extract electrochemical kinetic parameters for methanol oxidation such as the exchange current density, Tafel slope, and energy of activation for the reaction. Kinetic data, especially at different temperatures, is very limited in the literature.

Jan 1, 2005

By Weijie Wei, Jinwang Zhang, Jiachen Wang, Yang Li

"Longwall top-coal caving (LTCC) mining technique is one of the important methods for underground thick seam extraction in China. The coal seam in LTCC panel is divided into two parts: bottom-coal and top-coal. The bottom-coal is mined by conventional longwall method while the top-coal is mined by caving method. The top-coal caving process in LTCC and block caving process in metal mine are both gravity flow of loose ore/coal blocks. However, the presence of caving shield in LTCC makes the characteristics of drawing body shape in the two caving processes differ a lot. This paper discusses the influence of caving shields on the characteristics of drawing body shapes in light of recent studies of the top-coal drawing process. The theoretical model for describing the drawing body shape in LTCC is proposed both along the seam strike and seam inclination. Then, the experimental data are used to validate the correctness of the theoretical model. Furthermore, two examples of how the theoretical findings assist LTCC mining are given and discussed.INTRODUCTIONLongwall top-coal caving (LTCC) mining technique and large-cutting-height mining technique have been widely used for extracting thick coal seams in China. About 0.6–0.7 billion metric tons of coal come from longwall top-coal caving panels every year. The maximum annual production is 15 million metric tons per panel _The mining method employed in such panel is a combination of top-coal caving mining technique and large-cutting-height mining technique, which is suitable for seam height between 12–20 m, as shown in Figure 1. Apart from China, LTCC has also been employed in some coal mines in Australia and Vietnam (Le et al., 2017).The coal seam in a LTCC panel is divided into two parts: bottom coal and top coal. The bottom-coal is mined by the conventional longwall method, while the top coal is mined by the caving method. The top-coal caving process in LTCC and block caving process in metal mines are both gravity flows of loose coal/ore blocks, as shown in Figure 2. However, the presence of caving shields in LTCC causes the characteristics of the drawing body shapes in the two caving processes to differ significantly.There are two main differences between the blocking method and the top-coal caving method:"

Jan 1, 2019

By Tapani Järvinen

Non-ferrous metals and metals in general are considered as being non-renewable natural resources. Metals are needed because of their excellent and irreplaceable properties. The consumption of metals, with the exception of carbon steel, is steadily growing by 1-3 % annually, and that of stainless steel as much as 3-6 %. This is a general trend, which is periodically disturbed by cyclical variations. In recent years so-called "New Economy" has become prominent in the public media and the market value of the traditional industry has been well below its real value and importance. Nevertheless, the modem society requires metals today and also in the future, and the companies using the most modern technology in a responsible way and innovative solutions not only in technology, but also in everything they do will survive. This paper describes the role of Europe as a producer of primary base metals and as a supplier of technologies in the base metals industry. It concentrates on the development and commercialization of technologies and project implementation in the metallurgical industry. As one example ofa European approach to these matters the paper presents Outokumpu's response to the future challenges in the base metals industry. Outokumpu Oyj is one of the leading metals and technology companies in the world of stainless steel, copper, zinc, and sales of technology in metals and minerals businesses. Outokumpu applies its knowledge of metals and processing to generate value for its customers and shareholder. Everything we do, we do in an economically, environmentally and socially responsible way.

Jan 1, 2003

By Alfred B. Annor

The introduction and application of paste backfill over the past two decades has resulted in substantial benefits being realised by many backfill reliant mining operations who have used this technology. Paste preparation over this time period has relied basically on mechanical dewatering approaches that have included the use of centrifuges, thickeners, and vacuum and pressure filtration. In large bulk mining operations, this method of paste preparation has usually involved the construction of big and complex surface plants to meet large tonnage demands. These large plants usually have attendant high capital, maintenance and operating costs. The application of paste backfill in narrow-vein mining requires more flexibility in terms of fill preparation, transportation and placement. The method of paste fill preparation should take into consideration low manufacturing and operating costs, ability to use existing facilities at mine sites, simplicity of operation and flexibility of preparing fill over a broad range of consistencies. This paper will review alternative paste fill preparation methods and indicate those that might be better suited to narrow-vein mining.

Oct 1, 2001

By P SSrkkS

Mining is commonly seen as a typical basic industry with rough and even dangerous working conditions, heavy environmental load, and a low level of high-technology and automation with much manual work and operations. A mining operation (open pit or underground) is a very complex one consisting of many manual, physical, mechanical and logistical operations with different human interfaces and decisions. For this reason it is a demanding and potential area for all applications of automation and information technology: controlling difficult non-linear, time varying multivariable processes and machines; solving of ergonomic safety and environmental problems; automation of logistical systems; applying robotics, mechatronics, and information handling, etc. In addition to that, big economic sums are involved with these operations. On the other hand, automation technology has developed towards intelligent and adaptive systems including some from the above mentioned fields of automation. Connecting them with modern information and communication technologies makes the idea of an intelligent and unmanned mine more and more feasible in the near future. This requires intensive co-operation and co-ordination between the mining industry and manufacturers of mining machinery. This has been successfully accomplished in the five-year Intelligent Mine research and development program as well as the three years of subsequent implementation of its results in Finland. The basic elements of an Intelligent MineTM concept are:mine-wide information and data acquisition system; high-speed two-directional mine-wide communication network for real-time monitoring and control; computerised information management, mine planning, control and maintenance systems; automated and tele-operated machinery and equipment which are connected to the information system; and links to the public information networks. The degree of automation of an intelligent mine depends on many technical and economical factors. The basic precondition for such an approach is that it will improve the total economy of the mine. This paper will describe the Intelligent Mine Technology Program with the results. Also the implementation which took place during starting of a new underground mine (Outokumpu Chrome Oy Kemi Mine) will be described.

Jan 1, 2000

By Maxime Tacher

BRP (Bombardier Recreational Products) designs and commercializes recreational vehicles such as watercrafts, sport boats, snowmobiles, ATVs... The Spyder roadster is the last product in the Can-Am product family lineup. To remain at the forefront of innovation, a hybrid motorization version of the Spyder is being developed in order to reduce fuel consumption and emission of greenhouse gases. But, the addition of electric components (e-motor, lithium-ion battery... ) raises the issue of added weight and volume. This article deals with the mass reduction of this Spyder by optimizing its frame.

Jan 1, 2011

By William H. Walton, Clyde N. Baker Jr., Darren S. Diehm

"A 51-story concrete core and steel frame commercial office tower was recently constructed on the site of the former US Gypsum building in downtown Chicago, Illinois, USA The structure foundation reused several caissons from the demolished US Gypsum building supplemented with new belled caissons bearing on silty clay hardpan. Extensive in-situ pressuremeter testing was performed during the geotechnical investigation to determine allowable bearing capacity and better estimate building settlements. Problems during foundation construction along the south side of the building frame required remediation of two caissons. One caisson was supplemented with micropiles, while the second caisson was abandoned and replaced with a straight-shaft rock socketed caisson. To determine the effectiveness of the repairs, the building foundation settlements were monitored during construction.IntroductionIn 2001, The John Buck Company began development of a new office tower at the southeast corner of West Monroe Street and South Wacker Drive in Chicago, Illinois. The site was formerly occupied by the 18-story US Gypsum (USG) building. Mr. Clyde N. Baker, Jr. (Senior Principal at STS Consultants, Ltd .) served as the foundation engineer for USG which was completed in 1962. The building was founded on a forest of belled caissons bearing at elevation -56 Chicago City Datum (CCD). For reference, the ground surface at Upper Wacker Drive is approximately elevation +20 CCD. The bearing material was a hard silty clay, locally described as Chicago Hardpan. The foundation caissons were designed using an allowable bearing pressure of 16 ksf (766 kPa). In 1996, the USG superstructure was razed, and the three-level basement was converted to an underground parking ramp.South Wacker DevelopmentThe 51-story high-rise building was completed in 2005 with a structural height of 681 feet (208 m), and an internal space of more than 1,000,000 square feet (93 ,000 square meter). The typical floor size is 27, 700 square feet (2, 570 square meter). Renderings of the building are provided in Figures 1 and 2. The largest single tenant is the accounting firm of Deloitte & Touche, which occupies roughly 45% of the building space with over 3,000 employees."

Jan 1, 2005

By John W. Cahn, John E. Hilliard

Single crystals of copper and silicon-iron were cold rolled in orientations chosen to produce individually the major components of the poly crystalline deformation texture. The orientation dependence of the recrystallization kinetics was studied relative to the primary recrystallization textures of these specimens. It is not possible to rationalize the poly crystalline re crystallized textures on this basis. The results suggest an important role of the interaction of adjacent crystals during the deformation of aggregates. BRICK and Williamson1 first noted evidence that the recrystallization temperature was different for straight-rolled and cross-rolled copper given comparable reductions. Michalak and Hibbard2 investigated quantitatively the effect of rolling procedure on the kinetics of recrystallization of cold-rolled copper and found that material cold-rolled the same amount by straight-pass, cross-pass, and compression-pass techniques developed different deformation and recrystallization textures, different 1-hr recrystallization temperatures, and different recrystallization kinetics. However, the temperature dependence of the rate of recrystallization was essentially the same for all techniques. Similar results were obtained on iron. Dunn and Koh3 in studying the recrystallization textures of cold-rolled silicon-iron single crystals reported large differences in the annealing temperatures and times required to recrystallize specimens of different orientations cold-rolled the same amount. Liu4 and Liu and Hibbard5 utilized the concept of different recrystallization temperatures for different orientations of cold-rolled crystals to rationalize the difference in recrystallization textures found in various face-centered-cubic metals. Their explanation predicted a significant difference in the recrystallization kinetics of deformed (110) [112] crystals as compared to (358) [352] crystals, and, in fact, Liu4 reported evidence that this difference existed at least qualitatively. Verbraak6 who rolled and recrystallized a series of copper single crystals found that the double (112) [111] rolled orientation is related to recrystallized cube texture formation. The effect of rolling intensity on the relative amount of cube component suggests an important role of recrystallization kinetics. Walter and Hibbard7 while trying to relate the behavior of rolled and recrystallized single crystals of silicon-iron to the behavior of polycrystal-line silicon-iron again noted that differences in recrystallization kinetics were necessary to rationalize their results. The purpose of the present investigation was to obtain quantitative kinetic data on the recrystallization of single crystals of both copper and silicon-iron rolled to initial isolated individual orientations corresponding to those found in the polycrystalline deformation textures. These data might indicate the importance of the deformation orientation, i.e. the range of available nuclei, the deformed matrix orientation into which these nuclei grow, and the orientation dependence of their growth rate during primary recrystallization on this texture. I. COPPER Experimental Procedure—A single crystal of 99.98 pet purity copper, grown by the Bridgman technique, was purchased in the form of a bar 1 1/2

Jan 1, 1962

By M. Ghamgosar, Erarslan N.

Rock cutting includes many unknown parameters which result in different consequences of the different cutting conditions. However, based on the current suggested models for rock cutting, there are some critical parameters that control the fracture initiation and propagation in the rock domain. In general, there are two major cutting tools are used in rock cutting: drag bits and indenters. Different mechanical attacks of cutters result in different fracture models. For example drag bits break the rock parallel to the rock surface, which is called ‘undercutting’ while indenters cut rocks by pressing normal to the rock surface. Both tools cause rock failure by inducing tensile cracks in the rock. However, drag bits induce more tensile cracks compared with the indenters. The full benefits of improvement in rock cutting efficiency will arise from a clear understanding of rock fracture mechanics principles. Therefore, fracture mechanics principles will be applied to the rock cutting as the rock fragmentation process is based on the rock fracturing. The Oscillating Disc Cutting (ODC) has more advantages than drag bits and disc cutters. The forces transmitted back through the cutting head are much lower with ODC. Although ODC attacks rock in much the same way as drag bits, a combination of the oscillating action of the cutter and the undercutting mode produces the lower cutting forces and causes rock fatigue. Fatigue phenomenon in rock has advantages for the rock breaking by applying less effort and energy due to the cyclic loading. The aim of this study is using the Extended Finite Elements Analyses (XEFM) numerical modelling for simulating the ODC cutting with different cyclic loading conditions. An accurate prediction of numerical investigation requires detail laboratory experiments. A series of laboratory tests were performed to obtain the fracture toughness values of our Monsonite rock samples under various cyclic amplitude and frequency values. The numerical results showed different types fatigue damage mechanisms due to the various cyclic loading conditions. Thus, modelling and understanding the crack propagation behaviour depending on different amplitude and frequencies are believed very important for the dynamic rock cutting researches and rock cutting machine manufacturers.

Jan 1, 2015

By Phil Wilkinson, Sam Whitaker

"The installation of large (XL) diameter monopiles offshore typically requires expensive and specialist plant, equipment and vessels. Due to the increasing size (weight, diameter and length) of the foundations, in order to mitigate installation risk, the use of large diameter drills is becoming an increasing requirement.Project developers often try to avoid drilling operations due to the time associated with the drilling process. This restricts projects in terms of location and it also overlooks the additional engineering benefits drilling can bring to monopile foundation design e.g. reduced foundation material and better fatigue design life.By comparing the lessons learned of three milestone overwater drilling projects; methods of maximising drill speed and decreasing drilling process time is established. Particular emphasis is put on pile internal relief drilling in a process known as Drive-Drill-Drive (DDD).The milestone overwater drilling projects are North Hoyle Offshore Wind Farm (OWF) (2003); Flamanville EPR cooling water outlet shaft (2008); and Gwynt-y-Mor OWF (2014).By evaluating the effect of foundation pile diameter on drilling process times, example foundation installation costs are derived and used to show that incorporating drilling as part of a process may not be cost prohibitive to projectsContinued advances in drill technology, and drilling rates of penetration, combined with an integrated approach to foundation design, challenge whether hammering only is always the optimal solution for XL monopile installation."

Jan 1, 2017

By Matthew Geary, Stephen J. Marino, Jordan A. Schreiner

"INTRODUCTION Project Overview The Southeast Collector (SeC) is a new 15km long 3.0m internal diameter wastewater tunnel designed by Hatch Mott MacDonald (HMM) that twins the existing 2.6m diameter York-Durham Sewage System (YDSS) tunnel. Both sewage tunnels are located north of the City of Toronto in Ontario, Canada. The SeC provides much needed conveyance capacity for the rapidly growing York Region population, supporting development until 2036 and increasing sewage system security (Hatch Mott MacDonald and AECOM 2011). Construction of the SeC will also permit flows of the twinned section of the YDSS to be bypassed in order to clean, inspect and carry out any essential maintenance within the YDSS tunnel. Although owned and operated by York Region, the SeC spans two regional municipalities beginning upstream from the intersection of Ninth Line and Rouge Bank Drive in the City of Markham in York Region to the downstream Finch Avenue and Valley Farm Road intersection in the City of Pickering in Durham Region. See Figure 1 for the SeC and YDSS alignment. The project includes 19 shafts and chambers with depths ranging from 8 to 48m in addition to seven facilities supporting the operation and maintenance of the sewer. The construction contract was awarded to Strabag Inc. in July 2011 for $291M CAD. Construction Management services were provided by a joint venture team of Hatch Mott MacDonald and AECOM. Existing York-Durham Sewage System The YDSS tunnel was completed in 1979 and was constructed using an open shielded TBM with ribs and lagging temporary support, followed by installation of a 380mm thick unreinforced cast-in-place (CIP) concrete final lining. The YDSS sewer system has numerous connections that accumulate flows from various urban areas within York Region. The section of the YDSS twinned by the SeC flows under gravity conditions and had been putting a strain on the municipality’s potential for population and development growth having reached its maximum capacity of 420 ML/d. According to the York Region’s Water and Wastewater Master Plan, the existing YDSS would not have been able to handle wet weather flows past 2016 (Genivar and XCG Consultants 2009). The dependability of this section of the YDSS is also of concern because it is the main and critical connection between the sewer systems upstream and the downstream Duffin Creek Water Pollution Control Plant (WPCP)."

Jan 1, 2016

"The first 90 years of the last century generated a considerable volume of technical literature on the subject of grinding mill power and its prediction. It is therefore surprising that during this time there were no published models for predicting grinding mill power draw which were validated using a wide range of comprehensive industrial scale data.Notwithstanding this lack of data, the majority of models placed limited emphasis on the internal dynamics of mills and relied on simple assumptions which considered the charge to take up a fixed position and shape.Laboratory based studies (Liddell, 1986), and industrial data (Morrell, 1993), showed that these assumptions did not hold over a wide range of operating conditions, and brought into doubt the ability of the (then) existing models to accurately predict grinding mill power draw. Furthermore no model treated AG,SAG and ball mills as a single class of devices whose power draw could be predicted with the same equations.Through a detailed investigation of the charge dynamics, coupled with a large data base of industrial mill power draws, this situation was rectified by the end of the century, by which time a model had been developed and validated, which accurately predicted the power draw of all wet tumbling mills. This paper describes this model and reviews some of the earlier attempts at mill power modelling."

Jan 1, 2003

By Donald A. Bruce

"The Deep Mixing Methods (DMM), in their current forms, have been employed in the United States since 1986, although an earlier version had seen service from 1954. The earlier developments were strongly influenced by practices in the Nordic countries and Japan, while by the late 1980’s several DMM systems had been developed in the U.S. itself. Since then, DMM has continued its evolution, principally via the challenges of a series of large, landmark projects, but also via distinct, significant technological advances. This paper highlights the key points in the history of DMM in the U.S., and provides an overview of the different methods currently in use.IN THE BEGINNINGIt is a common misconception that the history of applications of the Deep Mixing Methods (DMM) in the United States dates from 1986 when SMW Seiko Inc. — a subsidiary of Japan’s Seiko Kogyo Company — was established in the Bay Area. However, the author believes that Intrusion Prepakt Co.’s patented MIP (Mixed in Place) system had been used, albeit sporadically (about 30 projects are recorded), since 1954 (FHWA 2000, 2001). Ironically, by 1961 this single auger method had been extensively used under license in Japan for excavation support and groundwater control — by the Seiko Kogyo Company. By 1972, the original MIP technique had been succeeded by more advanced Japanese methods, involving multiple augers. Intrusion Prepakt have long since become defunct.The first systematic studies of contemporary Deep Mixing Methods in Japan began in 1967 when the Port and Harbor Research Institute of the Ministry of Transportation began laboratory testing using granular and powdered lime for treating soft marine soils. Fundamental studies continued through the early 1970’s, by which time the development of industrial scale equipment was well advanced, having its first application on a marine trial near Haneda Airport. Coincidentally, laboratory and field research also began in 1967 in Sweden (“Swedish Lime Column Method”) for treating soft clays using unslaked lime. Reportedly the progenitor was a Norwegian, Kjeld Paus, who had made observations on fluid lime columns in the U.S. It would seem that developments in Japan and the Nordic countries proceeded independently until 1975 when the technology leaders from each group (Broms and Boman; and Okumura and Terashi, respectively) presented their — very similar — findings at a conference in Bangalore, India. Limited technical exchanges ensued thereafter.Whereas the Nordic developments continued to focus on the use of dry reagents (cement and lime) and relatively light equipment compatible with operating on and in very soft clays and organics, the Japanese progressed into the use of fluid reagents (cement-based grouts) and heavier equipment for both marine and land-based projects. Thus, by 1986, there were a large number of proprietary (wet and dry) DMM systems in Japan, and a rapidly growing market already by then accounting for over 12,000,000 m3 of ground treatment."

Jan 1, 2015

By B. K. Slone

The depth at which it becomes more economical to use slope access as opposed to box-cut access for near-surface coal reserves, termed "transition depth," can be established for a given coal property by considering cost estimates for those parameters that determine respective access method. Fourteen parameters that influence access cost were identified and ranges determined. A Transition Depth Formula was developed to permit determination of the better method of accessing a reserve, given such information as highwall slope, road width, total bench width, pit dimensions, road grade, belt component costs, pumping costs, and cost of overburden removal and reclamation. In most cases, in Appalachia, studies indicate that the transition depth ranges between 20 and 30 m.

Jan 1, 1998

By R. Laird Auchmuty

A NUMBER of factors, of varying importance, should be considered in assessing mineral land-here specifically coal land -for tax purposes. (1) Is the coal developed or un- developed'! (2) If undeveloped, is it surrounded by active development in adjoining properties? (3) Accessibility of railroad facilities to the property. Sometimes the railroad itself is of importance. (4) Cost of development of the seam under consideration, whether it can be developed by a drift from the outcrop or whether it will require deep and costly shafts or slopes. (5) Is it definitely known that the coal seam being assessed is of minable thickness and quality on the property? (6) Thickness of recoverable coal from the seam. (7) Quality of the coal. (8) Is the seam being assessed likely to be more costly to mine than other seams in the same district? (9) Is there an active market demand for coal from the seam being assessed? (10) Is the coal held only as protection to surface structures and in such location that it can never be mined? (11) Is the coal in a solid piece or is it in pillars that have been standing for some years as a result of incomplete mining in an old operation? (12) Expected percentage of recovery from the seam being assessed as determined by present mining practice in similar properties. (13) Value of the seam as indicated by sales of similar mineral rights in the immediate district. (14) Current royalty rates of leases for coal in the seam under consideration.

Jan 1, 1939

By Shuji Owada, Mayumi Ito, Takehiko Nishimura, Toru Yamashita, Sadayuki Shinozaki, Takashi Ando, Tomoe Ota

Electrical disintegration (ED) was applied to Nantun coal (China) in order to improve liberation of coal substance for the pretreatment of producing “Hyper Coal” of which the combustion gas was planning to inject directly to turbine for power generation. It has been found that many cracks generated in the ED were existent at phase boundaries with mineral matters and liberation of coal substance became much higher than that in mechanical comminution methods such as roll crusher. Since the ED occurred more easily (with lower voltage applied) for the coals of higher mineral content, it is considered that this method could make a better contribution especially to comminute middling coals. We also found that the ED technique could apply not only single particles but also to coal particles assemblage, keeping almost the same or higher disintegration efficiency. In the mineral matters, Si and Al components were preferentially well liberated by the ED.

Jan 1, 2003