Search Documents

By Gilbert Sauriol

The mining complex, which the Mines Gaspé division of Noranda Mines Limited has operated in Murdochville since 1954, includes open pit and underground mines, two mills, one leaching plant and a smelter. The under- ground mining uses predominantly a large scale room and pillar method, rooms 15 m wide, 30 m high and 300 m long being common. Ore production is effected by 4.5 m3 front-end loaders and 32-tonne trucks powered respectively by 225 and 325 kW diesels. Daily dust and gas readings show that air quality can be maintained at an acceptable level with much less ventilation than that normally specified. This paper emphasizes the point that air requirements should be based on Air Quality Standards, thus allowing an operation to benefit from favourable conditions or from improvements such as exhaust treatment, fuel alteration, etc.

Jan 1, 1983

By F. L. Wideman

This report describes the sinking of No. 3 shaft at the Westvaco mine. It is one of a series of publications of the Bureau of Mines on mining methods and practices in the United States. The Westvaco mine is in Sweetwater County, Wyo., approximately 23 miles northwest of the town of Green River (fig. I), There are no permanent habitations in the vicinity of the mine, and employees live in Green River or Rock Springs, Wyo., 14 miles us t of Green River. The mine plant is on a windswept, treeless plain, from which low buttes and flat-topped ridges rise. The altitude at the collar of No. 3 shaft is 6,351 feet. The climate is arid, with temperatures as low as 40° below zero in the winter. Blacks Fork, a tributary of the Green River and a perennial stream, flows near the mine.

Jan 1, 1959

By L. F. Willmott

Pulverized high-volatile A bituminous coal was gasified with oxygen and superheated steam in a pressure-gasification pilot plant equipped for slurry feeding. The minimum ratio of water to pulverized coal that could be pumped satisfactorily as a slurry was about 1 to 1. Heating this slurry produced a suspension of coal in superheated steam having a steam-to-coal ratio greater than the 0.3 to 1 proportion that is considered optimum for pressure gasification of pulverized coal. A steam separator removed enough steam to provide ratios down to about 0.5 to 1, but a 0.3 to 1 ratio was not achieved. Gasification of Sewickley coal produced a synthesis gas containing about 36 percent H2, 46 percent CO, and 13 percent CO2, Gas output, gas composition, and coal and oxygen requirements were Virtually the same as for a pilot plant equipped for fluidized-coal feeding. Typical results from the slurry-fed plant at 300 psig were carbon gasified, 95 percent; coal requirement, 34 lb/M (thousand) std cu ft CO + H2 produced; oxygen requirement, 365 std cu ft/M std cu ft CO + H2 produced. The results showed that the two feeding methods are equally satisfactory from the standpoint of gasification. A choice between a fluidized-coal gasification process or a slurry gasification process depends on considerations relating to the coal-feeding phase itself, including capital and operating costs, manpower requirements, safety, and flexibility of operation.

Jan 1, 1962

By A. K. Kyllo, N. B. Gray, B. N. McCurry

"Dynamic control of the formation of a solidified layer between a pipe wall and a flowing melt enables the flow rate to be adjusted in real time. This solidified layer can be generated by using a coolant on the outside of the pipe wall to remove the required heat. The coolant, and hence the solidified layer, can be controlled remotely. The dynamic behaviour of the solidified layer was investigated by both physical experiments and mathematical modelling. The mathematical model has been developed using a finite difference technique to describe conduction through the pipe wall and solidified layer. Results from the model were consistent with previous steadystate experimental results using molten lead. Experiments are currently being carried out using molten tin in a recirculating circuit with a cooling system that is instrumented for accurate computer control to validate the model. The circuit is designed for flowrates of up to 24 kg/s (86 tph) of molten tin. Steady-state and dynamic predictions were made for the current rig.Industrial SignificanceThe current method of choice for tapping slags, metals and mattes from many metallurgical furnaces is using an oxygen lance to open the taphole and using a clay plug to close it. There are, however, some significant drawbacks in this method. The heat generated by the oxygen lance erodes the refractory lining of the taphole, as well as the clay plug, and the furnace products themselves corrode the taphole. Using an oxygen lance is also a significant safety hazard to the operators as they must work in close proximity to the furnace and be subjected to a shower of sparks while opening the taphole. Also, the flowrate of material through the taphole cannot be controlled online as the diameter of the opening cannot be varied easily. This feature means that the level of product in a furnace cannot be kept constant."

Jan 1, 1999

By C. B. Kenahan

A summary of Bureau of Mines research on recycling, reuse, and disposal of mineral-, metal-, and energy-based wastes is presented, accompanied by an extensive bibliography of related publications. The Bureau's waste recycling and disposal program is directed toward the following four main areas of research and development: (1) extraction of mineral, metal, and energy values from urban refuse; (2) upgrading and recycling of automotive and related ferrous and nonferrous scrap; (3) recovery, utilization, and stabilization of mine and mill processing wastes, and (4) recovery and reuse of values from industrial waste products. This publication updates Bureau of Mines Information Circular 8529, which was issued August 1971.

Jan 1, 1973

By G. Stecklein

This report summarizes the results of research into the areas of the fragmentation and entrainment of Airborne Respirable Dust (ARD). The objectives of this program were four-fold: first, to review the present state of knowledge regarding ARD; second, to expand this state of knowledge through the identification of hypothetical microscopic mechanisms by which the coal is fragmented and the dust becomes entrained; third, to specify the informational requirements to verify or nullify these hypotheses; and fourth, to relate experimental techniques that will produce that required information. Additionally, insights are provided regarding potential methods of extraction and/or treatment which may reduce the concentration of ARD.

Jan 1, 1982

By I. L. Sills

Introduction So many minerals and mineral products are used in the glass industry that it would require an unduly long paper to deal adequately with all of them. Only those that go to make up the batch for the more common types of glass will be discussed here, and even with these only, the list is a lengthy one. It is true that for the body of the glass comparatively few materials are required-as silica sand, soda-ash, lime, and feldspar. The others are used mainly to colour or decolorize the glass, or to give it some other desired characteristic, such as high lustre, greater physical strength, or opalescence; but, although they may be present in very small quantities, they are just as in-dispensable to the glass industry as are the main constituents of the batch. Sand Sand is essentially quartz, the dioxide of silicon, Si02. Most glass contains from 71J to 75 per cent silica. Sand for use in the glass industry, or 'glass sand', is obtained both from deposits of unconsolidated material, commonly referred to as 'sand', and from solid rock-sandstone, quartz, or quartzite. For the manufacture of glass, the material must possess a high degree of purity, as noted below, so that, although sand is widespread in most parts of the world, and sandstone, quartz, and quartzite are not at all uncommon, it is only in certain places that suitable deposits are found. At the present time, most of the glass sand used in Canada is imported from France, Belgium, and the United States. The French material, from Fontainebleau, near Paris, is known the world over as a very high quality glass sand. That from Belgium is nearly as good and is lower is price.

Jan 1, 1934

By K. van Warmerdam, M. Pearson, C. Kember, D. McMullen, M. Thayer, C. Ugarenko

In July 2012, Hatch Ltd. and Air Products & Chemicals Inc. completed construction and commissioning of a 4000 tpd O2 cryogenic air separation unit (ASU) for Barrick Gold’s Pueblo Viejo Project located in central Dominican Republic. The ASU produces high pressure gaseous oxygen, which is used for the oxidation of refractory sulphide ore within the pressure oxidation (POX) circuit. As a result of the project’s remote location and tropical climate, many challenges were faced over the course of construction, commissioning and start-up of the ASU. These challenges included adequate preservation of equipment due to dusty and humid site conditions, final assembly and erection of the cryogenic distillation columns on site, limited spare parts inventory/availability, and an unfinished power source for plant commissioning. This paper discusses the steps taken by Hatch and Air Products to successfully design, construct, commission and start up the largest stand-alone ASU plant for a POX application in the metallurgical industry.

Jan 1, 2014

By Baohua Guo, Xuelin Yang, Tingkan Lu, Hailin Sun

The work presented in this paper mainly involves two parts. Firstly, the fundamental characteristics of the high pressure carbon dioxide gas fracturing technique (CO2 technique), including, a proposed method of TNT equivalence calculation, which is used to calculate the TNT equivalence of discharge of CO2 technique, and the comparison of the explosion volume generated by dynamite and expansion volume of liquid carbon dioxide is conducted to show the differences of fragmentation capacity between the two of them. Secondly, the coal seam fragmentation mechanisms of CO2 technique are proposed, including, 1) Gas jet cutting and penetration by shaped charge, 2) Gas volume expansion by changing phases of carbon dioxide, 3) Coal seam softening by destress blasting and 4) Coal seam fragmentation by discharge vibration, associating with the mechanisms, the equations for calculating fragmentation radius are developed and verified.

Jan 1, 2017

By L. H. Cole

FOR many years Industrial Minerals, or as they were formerly called, 'the Non-Metallic Minerals', compared with the metallics, were considered of only minor importance and as such were given scant attention in the technical press as well as in the public press. Those days are, however, happily passing, and thanks, to an appreciable extent, to the constant endeavour of the Industrial Minerals Section of this Institute, established in the fall of 1932 industrial minerals are now assuming the importance to which they are entitled. The term 'Industrial Minerals', when first adopted in this sense by the Institute, was thought to be original in its application, but it is interesting to note that it had been used many years previously by the Queensland Geological Survey in the following publication: SALT Article 1 in Industrial Minerals by B. DUNSTAN, Chief Government Geologist (Publication No. 268, in Part) Queensland Geological Survey, Department of Mines, Brisbane 1920 In Queensland, however, the term embraced some of the metals as well as the non-metallic minerals proper. The lead furnished by Canada in this matter bore rapid fruit, and already the term 'Industrial Minerals' is widely used, not only throughout Canada but in the United States as well.

Jan 1, 1939

By ALICE V. Petar

Among the rarest of the rare metals are four that are linked together by a common historical background as well as by chemical relationship. With the excep- tion of indium, these metals are likewise characterized by the patriotic nature of the names given them by their discoverers. The existence of gallium, germanium, and scandium, was predicted by the Russian cherist, D. I. Mendeleeff some time prior to their discovery; and these elements might well have been overlooked, had not the search been stimulated by the urge to confirm the scientific hypothesis of their existence. Nowhare found in sufficient quantities to attract attention, these little known elemente are nevertheless widely distributed in the earth's crust. So far they are found commercially mostly in the sulphide ores of zinc and must be considered as being largely curiosities of the zinc smelter. Recent progress in electrolytic zinc refining, however, now gives promise that the way may be open for the recovery of these very rare metals in larger quantities-- possibly in quantities sufficient to permit of their finding commercial utilization.

Nov 1, 1930

By R. J. Enright

Eight mines in canada and three in Australia were visited between September 1987 and Februacy 1988. All mines had encountered problems with sulphide dust explosions and had introduced defence mechanisms to prevent or limit the extent of these explosions. Techniques included dispersion of limestone by various methods, use of water foggers, placing of water and inert stenuning in blast holes, and removal of settled dust to prevent secondary explosions. The techniques were evaluated and it was concluded that certain practices should be modified or discontinued as they were of little value in preventing dust explosions.

May 11, 1988

By G. S. Scott, G. W. Jones, F. E. Scott

An important activity of the Bureau of Mines is the promotion of safety in mining and industry . In connection with these activities , the Bureau determines the explosion hazards of combustible gases , liquids , and solids , and investigates means by which explosions may be eliminated or reduced in violence . The limits of inflammability and ignition temperatures of combustible gases , vapors , and solids are of practical importance because such materials can be manufactured , transported , and used with greater safety , provided the range of concentrations and temperatures that cause explosions are known. Acetic anhydride , ( CH3CO) 20 , with which this report is concerned , is a liquid at ordinary temperatures . It is used in the preparation of a number of organic chemicals and in the manufacture of photographic film and of artificial silk . It is perhaps the most important acetylating agent for industrial uses - a property that is especially important at this time because of its direct application in the manufacture of munitions . The sample tested was supplied by the Carbide & Carbon Chemicals Corporation . Its specific gravity was given as 1.083 at 20/20 . The vapor pressures , supplied by the manufacturer , are plotted in figure 1 .

Dec 1, 1943

By Nan Wang

Based on the commercial computational fluid dynamics software, Fluent, a three dimensional finite-volume model has been established, and the fluid flow and heat transfer in the super-wide slab mold (cross section 3250mm×150mm) of Nanjing Iron and Steel Company has been simulated. The basic feature of flow and temperature field in a super-wide mold has been analyzed, and the effects of mold width, the submergence depth of SEN, outlet angle of SEN, casting speed, superheat and cooling rate on the flow and temperature field have been investigated. The results by comparing several simulated calculations for 3250mm×150mm slab show that a more proper fluid flow and temperature field in the super-wide mold can be obtained with 15°outlet angle, 120~150mm submergence depth of SEN and 1.2~1.4m/min casting speed. The results through numerical simulation provide a theoretical basis for optimizing the configuration design of SEN and choosing reasonable processing parameters for the continuous casting mold of super-wide slab.

Jan 1, 2009

By Kazuyuki Kakegawa

The sintering characteristics and the change in the compositional distribution in the PbTiO3-PbZrO3-Pb(Mg1/3Nb2/3)O3) system during the sintering process by spark plasma sintering (SPS) method were examined. They were compared with those by a normal sintering method. The densifieation by the normal sintering was slow even at high temperatures. When SPS method was employed, much lower temperature and shorter period resulted in sintered bodies having almost the theoretical density. As expected in normal sintering, the compositional distribution decreased as the sintered density increased. On the contrary, the change in the compositional distribution by SPS was much smaller than that in the normal sintering. This sintering characteristic of SPS suggested a possibility of fabrication of sintered material having a desired compositional distribution.

Jan 1, 2003

By Eric Johnson

"IntroductionHistoricalCyanidation is a leaching process, in world-wide use, to extract gold (and silver) from ores and concentrates. The process has many inherent advantages on account of its adaptability:a. to any scale of operation;b. to a wide range of ore types and mineral associations;c. to a wide range of physical characteristics of the gold particle size, alloy (electrum) or mineral (telluride);d. to relatively simple plant controls and operating procedures;e. to simple marketing procedures and quick cash return.The basic idea for cyanidation was first described and patented by a German chemist, L. Elsner, in 1846. Some forty years later, J.S. McArthur, a metallurgical chemist and R.W. and W. Forrest, medical doctors, all of Glasgow, Scotland, came to realize the import of the discovery and accordingly, registered patents in Great Britain in 1887 and in the United States in 1889. The keystone of the McArthur-Forrest patent registration was the use of weak (0.05o/o) instead of strong (1.0%) solution.The years 1890-1910 saw much progress in equipment design and the advance from batch to continuous processing to increase efficiency and reduce operating costs.In later years, technological progress followed advances in materials of construction and control systems. Current innovations include large-scale equipment, high-capacity thickeners, belt type filters and Steller, candle-type filters for plants using zinc dust precipitation. As well, environmental protection is increasingly a major concern.The technology of gold adsorption from cyanide solution onto activated carbon has made rapid strides in recent years. This has followed the initial efforts of Potter, Salisbury, Zadra and their colleagues of the U.S. Bureau of Mines Research Station in Salt Lake City, Utah, and the field work of Homestake Mining Company personnel, in Lead, South Dakota."

Jan 1, 1989

By Kazuyuki Kakegawa

The sintering characteristics and the change in the compositional distribution in the PbTiO3 PbZrO3-Pb(Mgl/3Nb2/3)O3 system during the sintering process by spark plasma sintering (SPS) method were examined. They were compared with those by a normal sintering method. The densification by the normal sintering was slow even at high temperatures, When SPS method was employed, much lower temperature and shorter period resulted in sintered bodies having almost the theoretical density. As expected in normal sintering, the compositional distribution decreased as the sintered density increased. On the contrary, the change in the compositional distribution by SPS was much smaller than that in the normal sintering. This sintering characteristic of SPS suggested a possibility of fabrication of sintered material having a desired compositional distribution.-

Jan 1, 2003

By Kenneth Blower

This paper gives a detailed coverage of the ore flow through the primary crusher, cobbing plant and concentrator, including equipment sizes, recoveries, reagent consumptions and product descriptions. Special features, such as rubber chutes, rubber-lined mills, pebble-mill grinding, steam-hooded filters and process control instrumentation, are also discussed.

Jan 1, 1968

By I. P. Swainson, A. Ilbagi, H. Henein

Powders of Al-50wt%Ni, Al-40wt%Ni and Al-36wt%Ni were produced using the Impulse Atomization technique, a rapid solidification technique. The molten droplets were cooled in-flight by the stagnant helium or nitrogen in the atomizing chamber. The resulting powders were sieved into different size ranges. X-Ray diffraction and neutron diffraction were used in order to quantify the phase fractions in the samples. The computer software GSAS was used to calculate the weight fraction of the existing phases, namely Al3Ni2, Al3Ni and Al, by profile refinement method. The effect of processing parameters, alloy composition and particle size will be discussed in this paper. In brief, no AlNi was found in any of the samples analyzed. Higher cooling rates resulted in the reduction of the ratio of Al3Ni/Al3Ni2. Also, at high cooling rates, Scheil closely predicted the ratio of Al3Ni/Al3Ni2. Some metastable phases were found in Al- 36wt%Ni.

Jan 1, 2010

By Harold L. Rhodes

The Bureau of Mines has developed a quantitative method to determine water vapor in helium in the range of 0.1 to 15 ppm by volume. This method uses the quantitative chemical reaction of H20 with CaH2, which produces 1 mole of hydrogen for each mole of H20 in the sample. A gas chromatograph is then used to determine the concentration of hydrogen in the product. The precision of the H20 analysis is ±0.05 ppm at a concentration of 1 ppm. This method is used to calibrate a commercial platinum-phosphorus pentoxide (Pt-P205) electrolytic water vapor analyzer that has an improved inlet system and digital voltmeter readout.

Jan 1, 1981