Search Documents

By O. J. C. Runnals

The intermetallic compounds NpAl2, NpAl3, and NpAl have been prepared, and examined by X-ray diffraction methods. The compounds are isostructural with the corresponding U-Al compounds. NpAl3 is face-centered cubic with a = 7.785A and has the MgCu2 structure. NpAl is simple cubic with a = 4.2624 and has the AuCU3 structure. NpAl4 is body-centered orthorhombic with a = 4.428, b = 6.268, and c = 13.71A. The published description for the atomic positions in UAl, applies also to NpAl4 THE U-Al system has been examined by Gordon and Kaufmann.1 They identified the following intermetallic compounds: UAI2, UAl3, and a third, tentatively identified as UAl5. A structure analysis of the latter compound by Borie2 proved that the formula UAl4 was more consistent with the X-ray data. The crystal structures of UAl2 and UA have been reported by Rundle and Wilson.3 UAl2 was found to be isostructural with MgCu. The atomic positions in the simple cubic UA1, cell were found similar to those in the AuCu3 structure. Three analogous compounds exist in the binary system Np-Al. X-ray data for the compounds NpAl2, NpAl3, and NpAl4 are reported below. The neptunium used in the investigation was supplied through the courtesy of the Argonne National Laboratory as neptunium (V) nitrate. It was stated to have a radioactive content of 99.25 pct Np237. The impurity limits had been established by a spectrographic analysis given in Table I. Any titanium, boron, or bismuth impurity should be effectively removed during the fluorination of NpO2 to NpF4, and sodium, lithium, magnesium or strontium during the alloying procedure. The oxalate ignition technique, described by Westrum for the preparation of finely-divided reactive PuO2, was used.The neptunium (V) nitrate solution, containing 100 mg Np, was evaporated to dryness on oxalic acid crystals. The resulting oxalate was calcined to NpO, by heating in platinum at 650°C for 2 hr. An equimolar mixture of anhydrous hydrogen fluoride and purified hydrogen was passed over the NpO2 for 2 hr at 500°C. According to Fried and Davidson" the above fluorination conditions should produce the purple-black fluoride, NpF3 However, the light-green product showed only NpF4 lines on an X-ray diffraction pattern and contained only an estimated 5 pct of finely dispersed black NpF3 particles on microscopic examination. NpAl3: An intimate mixture of 50 mg of neptunium fluoride and aluminum powder (99.99 pct pure, —28 to $60 mesh) was heated to 900°C in a BeO crucible in vacuum by a tungsten coil for 2 hr, to allow the following reaction to proceed: NPF4 + 7Al + NpAl, + 4AlF. [1] The formation and sublimation of aluminum mono-fluoride in this system was verified from an X-ray diffraction analysis of the sublimate. The diffraction pattern was similar to one obtained in the aluminum reduction of UF4 to UF3,6 showing both Al and AlF3 lines. The resulting alloy was sintered at 1100°C for 1 hr. A powdered specimen of the crystalline product was sealed in a thin-walled quartz capillary for X-ray examination. The photograph was taken on a 14.32 cm General Electric powder diffraction camera, using filtered copper radiation. The films were calibrated in terms of a NaCl standard pattern. The wavelengths used in the calculations were 1.5418A for Cu K and 1.5405A for Cu K The powder diffraction pattern showed that NpAl is simple cubic with a = 4.262 % 0.005A, and is isostructural with UA13 where a = 4.27A1 or a =

Jan 1, 1954

By T. Szaplonczay, D. E. Light

The auto-oxidation of sulfur dioxide to form sulfuric acid in commercially produced barren and recycle liquors, containing 1.66 and 4.56 gpl Fe respectively, from Elliot Lake was studied. A gas mixture, containing 3.5% SO2 and air was introduced into these liquors through a frit at a rate of 6.0g SO2 per hour per liter of solution. The barren and recycle were heated to 60°C. At the end of the first 24 hours of the process the concentrations of acid produced were 158 and 220 gpl H2SO4 for the barren and recycle respectively. Corresponding conversion efficiencies were 70 and 83%. In the period from 24 to 36 hours the rate of acid production decreased so that the H2SO4 concentrations at the end of 36 hours were 180 gpl for the barren and 260 gpl for the recycle; average conversions for the initial 36 hours were 55 and 68% respectively. Many investigators1'2'3 have considered the oxidation of sulfur dioxide to form sulfuric acid in aqueous solutions containing metallic ions. A summary of the work performed on this subject prior to 1946 has been presented by Keyes4 who described the auto-oxidation process as follows. Keyes also suggested that in this second reaction ferric ion serves as a catalyst for the conversion of sulfur dioxide to sulfuric acid. Neytzell-de Wilde and Taverner5 have reported on the use of auto-oxidation to produce a 4 to 5% sulfuric acid solution for use in a cyclic leach process at South African uranium plants. This paper describes investigations carried out to determine the feasibility of using the auto-oxidation process to produce sulfuric acid solutions of as high concentration as possible using commercially produced uranium plant barren and recycle liquors from the Elliot Lake region of Ontario. These liquors contained 1.66 and 4.56 gpl respectively of iron, chiefly in the ferrous state. This investigation is of particular interest to the uranium producers in Elliot Lake where the ores contain 3 to 4% sulfur, as sulfides. Flotation of these sulfides and roasting of same to produce SO, bearing gases have been successfully demonstrated using conventional methods.6'7 Barren and recycle solutions, as described previously, are also produced in large tonnages by these uranium producers. The experimental method and apparatus used to examine the auto-oxidation process will be described first. Then the tests carried out on laboratory prepared aqueous solutions containing ferric sulfate to determine optimum conditions will be presented. The next section will describe the tests using the commercial barren and recycle liquors. A final section will summarize the conclusions of the work. EXPERIMENTAL APPARATUS AND PROCEDURES Two types of solutions were used in the tests, a laboratory prepared aqueous solution containing definite amounts of ferric sulfate, and commercially produced iron bearing solution obtained from a uranium leaching plant in the Elliot Lake area. Two liters of a solution to be examined were placed in a 3 in. diam by 30 in. long glass cylinder with a cross-sectional area of 7 sq in. A mixture of air, and SO2 supplied from a lecture bottle for convenience, was introduced into the bottom of the vessel through a standard 30 mm glass frit, 700 sq mm in area. The temperature of the apparatus was controlled by a heating tape and variable transformer. Exhaust gases were vented to atmosphere. At the end of the test period the gas flow was shut off and the solution was analysed for H2SO4, Fe ++, and Fe +++, by conventional means. Four variables were examined using the laboratory prepared aqueous solution of ferric sulfate. First, the effect of SO2 concentration, from 1 to 1076, in the feed gas mixture was considered. Second, the temper-

Jan 1, 1964

By Peter Radziszewski

"Comminition process costs, which typically represent an important contribution to mining operating costs, can themselves be divided roughly between energy and liner /charge wear. As such, developing the ability of predicting mill wear will allow a more accurate estimation of wear costs and therefore their control. In this paper and based on the possibility of estimating energy dissipated in impact and abrasion by using a discrete element charge motion model for mill charge motion simulation, media wear will be investigated principally as a function of three wear mechanisms : impact, abrasion and corrosion. Experimental results will be used to identify a total media wear model. Model results will be compared with real mill data from three operating Australian mines. These preliminary results show for the cases tested that the overall average error, as compared with the observed cases, is 0 % with a standard deviation of 66.1 %. Results from the Bond abrasion index tests, for the same cases investigated, give an overall error of 73 % and a standard deviation of 192.5 %. Further work is in progress to improve test procedure, validity and confidence.INTRODUCTIONComminition process costs, which typically represent an important contribution to mining operating costs, can themselves be divided roughly between energy and line / charge wear. In Greenfield situations where the estimation of operating costs is critical in determining project feasibility, the level of confidence in such estimates becomes quite important. With regards to media wear, the Bond abrasion test currently serves as the standard media wear prediction device. However, as shown [l, 21 test results once compared with actual wear rates can vary greatly. Figure 1 shows test results as compared with 15 cases. Average error over this data is 73 % with a standard deviation of 192.5 %. As such, developing the ability of more accurately predicting mill wear will allow greater confidence in wear cost estimation and therefore their control."

Jan 1, 2001

By Uchil Jayagopal, P. V. Krupakara, S. Manjunath

"This paper deals with the corrosion characterization of quartz particlate ZA-27 alloy metal matrix composites (MMCs). Quartz particles of size 50-80 microns are used as reinforcement. MMC's are prepared according to ASTM standards. Composites containing. 2, 4, and -6% by weight of quartz and unreinforced matrix were tested using 1 -N hydrochloric acid: The composite was found to be more corrosive resistant than matrix alloy. In each test the corrosion resistance of both alloy and composites were found to decrease with the exposure time.1. IntroductionMetal matrix composites- (MMCs) offer designers many added benefits, as they are particularly suited for applications requiring good strength at high temperature, good structural rigidity, dimensional stability, and light weight 1-5. The trend is towards safe usage of the MMC parts in the automobile engine, which work particularly at high temperature and pressure environments Particles reinforced MMCs has been the most popular over the last two decades.ZA alloy MMCs have most popular families being represented by. ZA-27 alloy reinforced with ceramic particulate. Although the incorporation of the second phase into a matrix material can enhance the physical and mechanical properties of the base metal, it could also significantly change the corrosion behavior.ZA alloys have been used extensively in industry. This is attributed to their excellent fludity, castability and good mechanical properties. Among the zinc-based foundry alloys, the ZA family of alloy have been widely used during the past few years. ZA alloys have many advantage over aluminium based ones, especially high strength with a low casting temperature 8."

Jan 1, 2000

Applying DEM to prediction of tumbling mill performance is challenging because several different modes of breakage are active in the process. As our knowledge of breakage and computational capacity improve, it is worth revisiting previous simulation tasks which did not produce a satisfactorily realistic description of a measured process. At SAG 2006, we reported the simulated and measured outcomes of treating a well characterised ore in a 1.2 m diameter mill. This well instrumented, pilot scale mill at the University of KwaZulu-Natal has been combined with some new approaches to ore testing to allow different modes of breakage to be tested. The mill design allows the rate of generation of fine material to be measured in close to real time for autogenous and SAG mill charges. The updated simulation model estimates mass loss with particle evolution and embeds the cumulative damage and breakage. The simulated results are compared with the measured results. Issues such as relating modelling inputs to particle breakage characterisation data and the accuracy of the predictions of the models are discussed.

Jan 1, 2012

By C. Van Dyke, K. Van Dyke, J. Gutierrez, C. Nowack

"Using propidium assay and flow cytometry, we examined how silica exerts its toxicity toward phagocytic cells employing the human neutrophil as a model. This toxicity appears to be associated with calcium bound to silica. Once the silica with calcium is phagocytized, the extra calcium causes the death of the cell. Using ""Ca we found that 6 to 10% of millimolar calcium is bound to milligram amounts of respirable-sized silica (diameter of 5 µ.m or less) at physiological pH. If the silica particles arc coated with an organosilanc (Prosil 28). calcium binding is decreased by 60% as is cell death. Pretreating with INDO IAM (a chelator of intracellular calcium) reduces the cellular death by 80%. Nonfibrogcnic particles- polystyrene beads or coal dust-produced 10% or less cell death in a 4-h period. Silica with no added, external calcium appears to exert toxicity to neutrophils; however, pretreating cells with EDT A decreases cellular death to the level of nonfibrogcnic particles. Chronic toxicity with silica-calcium appears similar to the chronic toxicity in gout where particles cause a cycle of inflammation. c 1993 Academic Press, Inc.Silicosis is an occupational disease caused by the inhalation of fine particles of silica, usually between 0.1 and 5 µ.m in diameter (1). A recent hypothesis explaining silica's toxicity suggested that surface free radicals caused damage to cells (2). This explanation appears doubtful, however, since the addition of silica to water, such as that found in biological systems, quenches free radicals; also, such a hypothesis does not provide basis for a persistent inflammatory pattern that lasts for years. Kane et al. (3) proposed that silica's toxicity resulted from an excessive concentration of calcium ions within the phagocytic cell (macrophages). However, the mechanism that was capable of linking silica to an excess of intracellular, ionic calcium was not explained. The surface of silica is certainly involved because covering the surface with polymers or phospholipids decreases silica's toxicity (4-6).When silica is engulfed by macrophages platelet activating factor and leukotrienes are produced (7, 8). This is the same inflammatory pattern produced by phagocytic cells exposed to the calcium ionophore A23187 and ionic calcium. How could silica be acting like A23187? Perhaps calcium binds to silica extracellulary and then is released intracellulary following phagocytosis; the latter process, in a sense a ""piggy back"" process, would permit activation of inflammation and cell death mechanisms."

Nov 1, 1995

By J. W. Horne, W. B. Shirey

"INTRODUCTION The United States Bureau of Mines in cooperation with the State of Colorado at the University of Colorado has conducted experiments to determine the amount and composition of the noncondensable gases evolved when crude shale oil is distilled under pressure.Hydrogen sulphide is one of the components found in the complex mixture of gases produced by the distillation of shale oil under pressure. This paper deals with the apparatus and method used in determining the amount of hydrogen sulphide evolved in the laboratory experimental cracking stills.The study required a complete extraction of all the hydrogen sulphide from the gas stream after it left the water-cooled distillate condensers and before the as stream entered the charcoal absorber for removing the light naphtha. In devising the method it was necessary to take into account a constant variation of velocity, pressure, and percentage of sulphide in the total gas stream coming from the still.Ordinarily, the quantitative determination of hydrogen sulphide in Gas is made by analyzing small samples taken at regular intervals. This estimation can be accomplished by use of the Bunte gas burette as modified by Tutriler,4 or by a similar method. In the industries where the flow of as is constant end of uniform composition, this practice is sufficiently accurate for plant control. For experimental work where many variables have to be taken into consideration, as in the case at hand, these methods are not applicable."

Oct 1, 1931

By Terry Gerritsen, Sylvain Picard, Bruce MacKay

Virtually all new technologies require a control system. Any intense process has many process variables that react quickly making manual control difficult. Control system design has a significant impact on the success of a plant especially during ramp-up. New technology projects are particularly sensitive to control system design as the process response is unknown. This paper discusses the important factors encountered in the design of a control system for a new technology. Examples are given of successful new technology plant start-ups where tight coordination of the process control system implementation, process design and selection major equipment led to rapid ramp-ups.

Jan 1, 2011

By Kiyoshi Shibata

A new assessment model has been proposed for metal production and its recycling system. The model consists of three processes, smelting of ore, cascading and upgrading of metal scrap. The present approach is to assess the total energy consumption of the system, by introducing two equations for describing the relationships between critical impurity content and the mass of production or scrap recycling. The total energy consumption in the system can be described as a function of recycling rate and performance of the upgrading process. The present model suggests that the impurity removal efficiency and yield in the upgrading process are essential to reduce the energy consumption in the systems. Especially, such points should be explicitly controlled in recycling of aluminum. The potential capability of this model was also discussed by obtaining several quantitative information required for the process design and the operational control of beneficial recycling of metals.

Jan 1, 1998

By B. T., Colley

AS always when metallurgical operations are conducted within or close to agricultural and stock-raising regions, the question of damage due to fume and smoke presented itself when the Cerro de Pasco Copper Corporation's new smelter commenced to operate in La Oroya in 1922, For more than twenty years the Corporation had operated its old plant close to Cerro de Pasco without encountering difficulties from smoke claims, owing to the fact that it was in an open plain where more or less constant air currents carried and dissipated the smoke over large areas, affording ample dilution. But Oroya is in a deep canyon formed by four contributing valleys up and down which the smoke travels for long distances in a more or less concentrated form. Though the altitude of Oroya is more than 12,000 ft., and the surrounding country rises to much greater elevations, nevertheless there exists there a large and important stock-raising industry and also a considerable development in agriculture, consisting of the cultivation of potatoes, barley, etc.

Jan 1, 1945

By Marcie A. Greenberg

The Fence Lake Project is located in the Salt Lake coal field, an extension of the San Juan Basin. Geologic formations exposed in the Project area range in age from late Cretaceous to Quaternary. Coal is encountered in the Moreno Hill Formation (upper Cretaceous). Salt River Project (SRP) followed the basic textbook approach for the exploration, regional appraisal, detailed reconnaissance, detailed surface appraisal and three dimensional sampling (physical exploration). SRP is exploring this property as a potential fuel source for the Coronado Generating Station. Therefore, for the physical exploration stage, the quality sampling program was designed from a utility company viewpoint to determine possible impacts to the Station. Exploration drilling was completed in spring, 1982; September, 1982, and summer, 1984. Engineering, environmental, and land acquisition studies were added in the Summer, 1984 Program to more closely evaluate the potential Fence Lake Project coal supply option for the Coronado Generating Station. Studies, including drilling, are ongoing-at this time.

Jan 1, 1984

By L. D. Anderson

IN STUDYING Utah as a lead producing state one is immediately confronted by the fact that few, if any, of the ores of the state are valued for their lead contents alone. More correctly the ores from which this metal is recovered are characterized as silver lead. Even then the whole story is not told for many of these ores carry also gold, copper, zinc, bismuth, antimony, arsenic, tellurium, and other metals. It becomes apparent, therefore, that the production of lead i11 Utah is influenced by many factors. For example, i11 the early part of 1923 there was a marked increase in the production of the lead by reason of the efforts made by silver mines to produce as much silver as possible before the termination of purchases under the Pittinan Act in June, 1923. As nearly all silver ores carried more or less lead the production of that metal was increased with the increase in silver production. Very few, if any, ores of the State are mined for their lead contents alone. Important as Utah's contribution to the lead output of the country is nevertheless it is bound up to some extent with the production of gold, silver and copper.

Jan 1, 1925

By A. Modi, C. Li, R. Kabwit, W. Y. Xinchao, R. Joshi

The KIMIN copper project can treat 1.7 million dry t/a copper-cobalt ore. It has three mills in operation, two using conventional milling in water and the third in raffinate. We introduce the project process circuit and the capital and operating costs of using the raffinate process compared with conventional milling in water. There is a capital saving of approximately 11.5% for major equipment by removing the pre-leach thickener. In addition, it also achieves an annual operating cost saving of USD 2.1 million due to an increase in 49% of acidic raffinate recycled and reduction in lime consumption. The features of CITIC’s new duplex stainless-steel ball mill ,as the key equipment of the system, are also introduced

Jan 1, 2023

By Dong Hoon Han

The sulfation rates of magnesium oxide and calcium oxide (molar ratio 7:3) contained in calcined CMA ( calcium magnesium acetate) by SO2 were measured. The experiments were carried out in the temperature range 700 to 1100 °C and under the SO2 concentrations of 0.3 to I mol % (5 % 02). In the low-temperature range below 830 °C the reaction produced CaSO4.3MgSO4 and unreacted MgO, but no MgSO4 phase. The formation of CaSO4.3MgSO4 phase has a significant implication in that it allows the utilization of MgO for SO2 removal whereas the sulfation of MgO from conventional sources is so slow that it is of no practical interest. Thus, the calcined CMA can remove SO2 at lower temperatures than conventional SO2 absorbents and at a greater capacity. Above 950 °C only CaO reacts with SO2, but at a much greater rate than the calcined Ca(OH)2, which is one of the most reactive SO2 absorbents.

Jan 1, 1998

By Rafael Padilla

In the production of copper from chalcopyrite (CuFeS2) concentrates by the smelting and converting technology, the ambient pollution with gaseous S02 and toxic metals such as arsenic compounds is still a serious problem, especial1y in the converting step due to the batch nature of the conventional Peirce Smith process. Non-SO2 emitting alternatives are leaching processes. However, few of them have had a limited industrial application and they are not very effective in discarding safely the toxic impurities. A combination of pyro-hydrometal1urgical methods: the sulfidation of chalcopyrite and subsequent leaching of the sulfidized material is a non-polluting alternative to treat not only clean chalcopyrite concentrates but also complex chalcopyrite-enargite concentrates. In this article, this alternative is discussed concerning the thermodynamics and kinetics of the sulfidation of chalcopyrite with gaseous sulfur. The kinetics of the leaching of the sulfidized concentrate in an H2SO4-NaCI-O2 system is also discussed.

Jan 1, 2003

By V. Yahorava

Mintek has developed a non-destructive Resin-in-Leach method for the recovery of Rare Earth Elements (REE) from phosphogypsum (PG) waste dumps. However, PG from different sources was found to be highly variable in terms of REE recovery and physical properties. Development of a pre-treatment process was initiated to improve the robustness of the current REE recovery process in order to render it effective for any type of PG. Extensive research into the mineralogy of REE associations with PG revealed that the majority of REE are trapped inside phosphogypsum clusters which inhibits their recovery. Hydrothermal treatment of PG-containing slurry was found to result in re-crystallisation of gypsum with the release of REE phases encapsulated in it. This process was tested on various PG samples and subsequent REE recoveries improved from 5 to 80%. This approach carries a large potential for unlocking value associated with gypsum dumps worldwide.

By R. Hurman Eric

Within the Ag-Pb-S ternary system, the boundaries of the immiscibility region together with the tie-line distributions were re-established at 925°C by the equilibrium-quenching technique where samples were kept in evacuated and sealed silica capsules. Activities of Pb were measured by the dew-point method along the Ag-Pb binary at 925°C, 1100° and 1200°C. positive deviations were observed and the results were modeled by the Krupkowski formalism. Activities of Ag, Pb, and S, along the ternary miscibility gap were calculated at 925°C by utilizing the boundaries binary thermodynamics, phase equilibria and tie-lines. Activities of PbS within the pseudobinary Ag2S-PbS mattes were also measured by the dew-point technique and the results were again modeled by the Krupkowski formation Where negative deviations were observed.

Jan 1, 2003

By E. B. Freidina

We have investigated a new electrochemical process for preparing lead-calcium alloys. Calcium metal, reduced fiom a molten chloride mixture, forms an alloy with liquid lead cathode. The addition of calcium carbonate to conventional CaC12-NaCl electrolyte enables us to avoid chlorine production on the anode and replace it with oxygen and carbon dioxide. The ternary system CaClz-NaC1-CaCO3 has a range of melt compositions, where the electrolysis can be held below 650°C. In order to prevent the side reaction of carbon deposition on the cathode we have separated the anolyte from the catholyte with alumina diaphragm. The factors, which affect the level of impurities and the current efficiency of the process, are discussed.

Jan 1, 1999

By Steven R. Pittman, Colin McCullough, Peter Galuska

"Traditionally Continuous Fiber Aluminum Matrix Composites have been fabricated using high strength fibers and high strength matrices, often commercial alloys, with the goal of producing high strength composites. However the specific role of the choice of matrix alloy on composite properties has not been well established. One way to control composite tensile strength is to use coatings to introduce a low strength interface between fiber and matrix which tends to reduce the importance of the matrix selection, but unfortunately renders the transverse strength unacceptably low. Thus using a system with strong bonding between fiber and matrix is desirable, such as an alumina fiber / aluminum alloy matrix system. In this case the transverse strength is a strong function of the matrix strength. However the longitudinal strength then depends largely on the characteristics of the matrix. The important role of the matrix is discussed using examples of alumina fibers in various aluminum alloy matrices. The key attributes are matrix constituent phases, alloy chemistry, alloy reactivity with the fiber, and matrix strength. From the understanding developed in these systems a set of design rules may be established for selecting an optimum matrix. IntroductionAluminum matrix composites (AMC's) reinforced with continuous fibers offer very attractive property gains over AI alloys, such as strength, stiffness, and fatigue resistance. These gains are magnified when specific mechanical properties are compared which make them attractive candidates for replacing steel, nickel, titanium and aluminum alloy parts in weight critical applications (1). Many systems have been tried in the past; B/AI, C/AI, SiC/AI, Si-Ti-C-O/AI and AI203/AI. Technically B/AI was a very good system but was expensive in regard to both fiber cost and fabrication and SiC/AI and C/AI systems are still plagued with reactivity problems. The Si-Ti-C-O/AI appears to be a good strength system but with lower stiffness. Until recently, the AI203/AI was a low strength system, in part due to a lack of a high strength fiber. Recently 3M introduced a high strength AI203 fiber - Nextel™ 610, which leads to high strength composites (1,2) and may also be both low cost and also compatible with less expensive casting approaches for fabrication."

Jan 1, 1996

By L. Becze, S. J. Hock, G. P. Demopoulos

"Regeneration of HCl from chloride solutions is commercially practiced by high temperature (800-900 °C) pyrohydrolysis associated with high energy consumption and capital cost. As an alternative to pyrohydrolysis a novel low temperature ( <200 °C) non-autoclave hydrolytic process has been studied in this research work, which comprises two steps. In the first step, ferrous chloride is oxidized by oxygen at 1;150 °C, followed by hydrolytic decomposition of ferric chloride to coarse hematite particles and superazeotropic hydrochloric acid (8-9M) operated at approximately 180 °C. This paper provides a summary of the laboratory results related to both oxidation and hydrolysis and presents a newly designed conceptual process flowsheet.IntroductionRecovery of base, noble and rare metals from ores and secondary materials (slags, dusts, residues) by chloride-based hydrometallurgical processes holds a lot of promise if a low cost HCl process becomes available. This is particularly so due to the high activity of HCl or more accurately activity of hydrogen ion [1] in concentrated chloride media and the formation of chlorocomplexes allowing for effective leaching under atmospheric leaching conditions and simultaneous ease of metal separation. However, during leaching significant amount of iron, which is associated with most of ores and secondary materials, goes into the solution. Hence, the obtained leach solution has to be treated to convert iron chlorides into easily filterable iron oxide and simultaneously produce concentrated hydrochloric acid. Apparently the critical operation of these processes is the regeneration of the lixiviant (HCl). Currently in the industry, its regeneration is accomplished by high capital and intensive pyrohydrolysis which operates at 700- 900 °C. Aimed at lowering the operational cost of pyrohydrolysis a process called PORI [2] was developed and tested in pilot plant scale in the 1970s for the purpose of treatment of pickle liquors without, however, resulting in industrial application."

Jan 1, 2011