Search Documents

By D. Mills, G. B. Craig

ZIRCONIUM has been float-zone-refined in an electron-beam furnace and the redistribution of oxygen, iron, and tungsten has been measured. The iodide zirconium used in the present experiments initially contained both oxygen and iron in the range 100 to 200 ppm by weight, and tungsten in amounts less than 10 ppm. Float-zone refining of zirconium, using induction heating, has previously been attempted by Kneip and Betterton1 and Langeron.2 Kneip and Betterton were primarily interested in the removal of iron and nickel. They achieved some purification, with respect to both these elements, in material given up to six passes at 150 mm per hr under an argon atmosphere. Langeron reported purification for a large number of elements after four completed passes in a static vacuum system operating at pressures less than 10-6 mm of Hg and with rates of zone travel between 30 and 40 mm per hr. He did not report oxygen concentrations, but stated that there was inverse segregation of this element. westlake5 has also used a minimum of four zone passes to remove iron from zirconium. No rates or conditions were given. Belk6 has shown that tungsten contamination can occur during electron-beam melting. He reported an increase from 0.01 to 0.05 pct by weight tungsten in molybdenum after four complete zone passes. The vacuum system for the electron-beam unit used in the present investigation consisted of a single-stage rotary pump backing a liquid-air-trapped oil-diffusion pump. A pressure of less than 10-8 mm of Hg was obtained with Dow-Corning 705 fluid in the diffusion pump. In order to avoid contamination of the zirconium by evaporation from the tungsten filament, a special focusing cage4 was employed. Three rates of zone travel, 114, 38, and 4 mm per hr, were investigated, with the liquid zone moving from the bottom to the top of the bar. The bars used were 3 mm diam and the total melted length was 130 mm. Oxygen was analyzed by neutron-activation analysis using a neutron flux of 10' neutrons per sq cm per sec to form the isotope N16 by the 016 (n,p) N16 reaction. The standard deviation is quoted for each oxygen determination. The iron and tungsten analyses were performed spectrographically, and the precision is estimated to be ±6 pct. Analyses for tungsten were all below the detectable limit of 10 ppm, confirming the protection given by the focusing cage. No significant redistribution of oxygen was found at the two higher rates of zone travel. The redistribution of oxygen and iron obtained after five passes at a rate of zone travel of 4 mm per hr (1.1 x 10-4 cm per sec) is recorded in Tables I and 11. Burris, Stockman, and Dillon3 have estimated the distribution of solutes during multipass zone refining. Using their curves for an effective distribution coefficient of Keff = 1.5 and 2 for oxygen and Keff = 0.3 for iron, the expected concentrations were estimated for the present material. These are shown in Tables I and 11, along with the experimentally measured values. The calculated concentrations are based on a molten-zone length of 10 pct of the total melted length, whereas in the present experiments the molten zone was approximately 5 pct of the total melted length. The effect of zone length on solute redistribution is most pronounced after a large number of zone passes. Comparison with Pfann's published data8 for solute redistribution for various Keff's and zone lengths indicates only small differences at low numbers of completed zone passes. It is evident that the expected distribution has not been realized in the case of iron. Scrapings of material deposited on the inner surfaces of the electron-focusing cage were found to be magnetic. It is, therefore, concluded that redistribution of iron is masked by evaporation. Deposition of iron inside the focusing cage was observed at all rates of zone travel. The results of the investigation may be summarized as follows: 1) Segregation of oxygen is typical for a solute with a distribution coefficient, Keff > 1. 2) No redistribution of oxygen takes place at high rates of zone travel. 3) The distribution coefficient for oxygen lies between 1.5 and 2.0. 4) Purification with respect to iron occurs mainly by evaporation. 5) The focusing cage is effective in preventing tungsten contamination.

Jan 1, 1967

By E. G. King

The work described in this Bureau of Mines report was undertaken to fill a need of industry for high-temperature heat-content data for uranium tetrafluoride. Without such data, heat balance evaluations of processes involving this substance are seriously hampered. Measurements of the heat content of uranium tetrafluoride were conducted at temperatures from 298° to 1,350° K. The melting point and heat of fusion were determined. The results are presented in suitable tabular form, and representative heat-content equations are included.

Jan 1, 1961

By Robert M. Grogan, James C. Bradbury

The Illinois-Kentucky mining district has, since 1880, accounted for 80 per cent of all U.S. production of fluorspar. The ore deposits are of two types: vein deposits formed by fissure fillings along faults and bedding-replacement deposits formed by the replacement of strata at certain favored stratigraphic positions along minor faults and fractures. Fluorite is the chief valuable mineral in the deposits. Sphalerite and galena commonly are present in small amounts but, in some ore bodies, may form a substantial part of the valuable constituents of the ore. Calcite is the chief gangue mineral; quartz and barite Exposed strata range from Devonian are present in various amounts. through Pennsylvanian in age. Igneous intrusive rocks occur as mafic dikes and sills and intrusive breccia dikes and plugs. Structurally, the district is situated on a generally northwest- trending arch that has been sliced into a series of long, narrow blocks by normal faults that trend northeastward. The structural The localization of the ore deposits by faults and fractures, the association of fluorite mineralization with intrusive breccias, and various lines of petrographic and geochemical evidence indicate that the fluorite-zinc-lead deposits were epigenetic and deposited by solutions emanating from a deep alkalic magma.

Jan 1, 1968

By R. L. Merek

There were 63 fatalities in the California petroleum industry in 1929, the largest number in any year since 1923 and an increase of 34.0 per cent over 1928, when 47 men lost their lives in the drilling, producing, manufacturing, and marketing divisions of the industry. It will be observed from the accompanying chart that after following a consistent decline for 4 years, the fatality curve turned upward in 1923 and advanced sharply in 1929. Although this increase in fatalities coincided with a period of intensive development it tends to indicate some laxness in the industry during a period of increased hazards. Intensive drilling campaigns are usually started hurriedly and conducted with a great demand for speed, and the result is that accident-prevention work is too often relegated to a position of minor importance.

Jan 1, 1930

By Paul Billingsley

NICKEL Plate mountain coincides closely with that portion of the Hedley mining district which is of economic interest. From it has come almost the entire past production, and the active mines of the present epoch, Nickel Plate-Sunnyside and Hedley Mascot, lie in a compact group near its summit. The Hedley district, which is 210 miles due east of Vancouver, is situated in the Okanagan range of southern British Columbia, where this rather gentle uplift is deeply dissected by the canyons of the Similkameen and its tributaries. The region is essentially part of the Interior Plateau of the Province (Figure 1), but is adjacent to easterly elements of the Coast Range. The Similkameen canyon, 4,000 feet in depth and frequently less than 4 miles from rim to rim, traverses the district from northwest to southeast. The deepest and narrowest portion of the canyon lies between Hedley and Keremeos, 18 miles to the southeast. At Hedley, an important tributary, Twenty Mile creek, enters from the north in a bold canyon, making a focus of unusually rugged topography. Nickel Plate mountain occupies the sector to the east of this junction (see Figure 2) and its flanks are ringed by the cliffs of Twenty Mile canyon on the west and by those of the Similkameen canyon on the south. On the east, it slopes gently to the hanging valley of Eighteen Mile creek, and on the north, with only slight loss of elevation, it merges into the moderately hilly surface of the plateau.

Jan 1, 1941

By R. L. Marek

There were 63 fatalities in the California petroleum industry in 1929, the largest number in any year since 1923 and an increase of 34.0 per cent over 1928, when 47 men lost their lives in the drilling, producing, manufacturing, and marketing divisions of the industry. It will be observed from the accompanying chart that after following a consistent decline for 4 years, the fatality curve turned upward in 1923 and advanced sharply in 1929. Although this increase in fatalitics coincided with a period of intensive development it tends to indicate some laxness in the industry during a period of increased hazards. Intensive drilling campaigns are usually started hurriedly and conducted with a great demand for speed, and the result is that accident-prevention work is too often relegated to a position of minor importance. [ ]

Jan 1, 1930

By James K. Stanley

When a plastically deformed mctal is heated to a certain temperature, it undergoes a complete change in microstructure, the consequence of which is a marked alteration of mechanical properties such as hardness, strength and ductility. This change in microstructure occurs by re-crystallization and is a process involving the formation and growth of strain-free nuclei in the deformed matrix. These nuclei continue to form with time and grow until a new grain structure replaces the cold-worked structure. The formation of the nuclei in the deformed sheet of I per cent silicon ferrite is illustrated in Fig. I. If a recrystallization is conducted iso-thermally, a nleasurement of the fraction of the matrix recrystallized plotted against time leads to an isothermal recrystallization curve, first established in 1942.1 Such recrystallization curves are shown in Fig. 4. These curves show that the recrystallization of a cold-worked metal is best considered as a rate process rather than a time independent process such as is suggcsted by the improperly named and misleading recrystallization diagrams involving deformation, temperature, and grain size.2-5 Any study of the rate of recrystallization resolves itself into a study of the component rates of nucleation and growth. The previous paper1 provided an account of the determination of the rates of nucleation; N, the number of nuclei formed per unit time per unit of unre-crystallized area, and growth, G, the radial growth in unit time, in the recrystallization of silicon ferrite (I per cent Si). A method was developed to furnish experimental data for evaluating the effect of the recrystallization variables on N and G. The mathematical analysis for the derivation of the isothermal recrystallization curve was developed for a two-dimensional case (in thin sheets where the diameter of the recrystallized grain is greater than the sheet thickness). The present paper is a continuation of the study of recrystallization of I per cent silicon ferrite begun in 1942.1 In this work the effect of the factors deformation, temperature, grain size, composition, and recovery is studied with respect to the rates of liucleation and grouth. At the same time it is shown how the cooperation of N and G affects the isothermal recrystallization curve. The study of these variables on N and G has a definite bearing on the mechanism of recrystallization and should lay a foundation for a rational theory on the subject. Procedure The procedure used in these experiments was essentially the same as that described previously but in certain details some changes were made in the interests of speed. With few exceptions, the procedure is the same for the study of all the variables. Where the procedure is different from standard manipulations attention is called to this fact.

Jan 1, 1945

By L. B. Pankratz

The heat contents of the sesquioxides of erbium, holmium, thulium, and ytterbium (Er203, Ho203, Tm203, and Yb203) in the cubic crystalline form were measured over the temperature range from 298° to 1,800° K. The erbium and holmium sesquioxides gave regular heat content-temperature curves. Thulium sesquioxide had a minor thermal anomaly near 1,680° K, with a heat absorption of 310 cal/mole; similarly, ytterbium sesquioxide had a minor anomaly near 1,365° K, with a heat absorption of 150 cal/mole. The heat content results are presented in both tabular form (at 100° intervals) and in algebraic form. Entropy increments, corresponding to the tabulated heat content results, also are listed.

Jan 1, 1963

By R. E. Barnes

An overall view of the perlite industry is concisely presented. The geology, mining, milling, processing, and applications of perlite, as well as the present status of the perlite industry are treated. Perlite, in strict petrological usage, describes a specific variety of volcanic glass in which strain, incident to cooling, yielded a concentric structure of fracturing which may be visible either to the naked eye or under a microscope. In commercial usage, the term perlite includes any naturally occurring acidic glass of volcanic origin that will expand when heated to a suitable temperature. The name perlite is a derivation of perlstein which originally defined "certain glassy rocks (hyaloliparites, hyalo-rhyolites) with numerous concentric cracks, from the fancied resemblance of broken out fragments to pearls."1 While perlite has been known to geologists for many years, it was not until 1941, while investigating perlite for use in enamel, that an assayer in Superior, Ariz., noted the unusual expansion characteristics of the ore. Further investigations were delayed until following World War II when many small plants were built and experimentation in the treatment and uses of perlite began. The Perlite Inst. was organized in 1949 to promote the development of the new industry, establish commercial standards through research, and to explore new uses and markets. The Institute, located in New York, represents some 50 producers in the U.S., Canada, Australia, England, France, Germany, Greece, Japan, Mexico, and New Zealand. In 1949, 71,l002 short tons of crude perlite were produced, sold or used by U. S. producers, and this figure increased to 325,0003 short tons by 1959. Such a rate of increase indicates the rapid and continuing growth of the perlite industry. GEOLOGY Perlite ore in its crude form has been found in seven of the mountainous western states, since un-devitrified siliceous volcanic rocks are limited to this section of the U. S. Commercially operated perlite deposits are normally of Eocene and Oli-gocene age.4 These deposits are often several hundred feet thick and may extend over hundreds of acres. In 1959, 13 companies in six states produced crude perlite, although the output in New Mexico comprised 79 pct of the total domestic crude output. Other states in order of their production were: Nevada, Arizona, California, Colorado, and Utah.5 Foreign deposits of perlite which are either producing or under exploration are Australia, Canada, Greece, Hungary,6 Iceland, Ireland, Japan, Mexico, New Zealand, and Sardinia. The ore may exhibit a variety of characteristics depending partially on its water content and eruption history and may range through many shades from black to white. While these characteristics may vary slightly among deposits, perlite ore from a particular source is normally quite uniform. Available chemical analyses of perlites from a large sampling of domestic deposits were recently assembled by the Technical Committee of Perlite Institute and are presented in Table I. While the ranges given do not apply to a particular perlite, they are an indication of the chemical analysis which may be expected from any presently commercially operated deposit. The specific gravity of the perlite ore ranges between 2.2 and 2.4, and its bulk density when crushed and sized is 75 to 90 Ib per cu ft. MINING AND MILLING Perlite ore is quarried from open pits by conventional power equipment, although blasting has been occasionally employed. The rock is then stock-piled until needed. While the milling of perlite may seem a simple process compared to that required for basic metals, or even other nonmetals, the need for accurate control of particle size becomes extremely important in further processing. The first step in this operation is the primary crusher, which is normally a jaw crusher. Following crushing, the material is dried, if necessary, in a rotary dryer and conveyed to a secondary grinder which may be a rod mill, hammer-mill, or cone crusher. However, the crushing characteristics of the perlite, caused by incipient cooling fractures, requires it be removed from the grinding operation once it is reduced to the required size so as to prevent overgrinding. Following the grinding operations, various size screens are used to separate the ore according to particle sizes required for particular uses. Most plants use two or more stages of crushing with perhaps four stages of screening.

Jan 1, 1961

By J. J. Stokes

Literature on the electrolysis of aluminum from cryolite melts and on the structure of these melts is surveyed critically. Data on density, freezing point, and other properties are reviewed. Theories of the electrolysis are examined in the light of these data. Two theories are presented which account equally well for the observations. ALTHOUGH the production of aluminum is a large-scale industrial process, consuming approximately 3 pet of all of the electric current generated in this country, the mechanism of the Hall Process remains a 70-year-old mystery. It is a remarkable fact that the aluminum industry, which was established largely through research and owes much of its growth to research, still employs as its basic process the one developed by Charles Martin Hall while he was still a young man working in a woodshed. There are, of course, modifications in detail and a tremendous expansion of the size of the units used, but basically the process employs carbon anodes and a carbon-lined iron vessel as a cathode for the electrolysis of alumina dissolved in molten salt. Of the almost infinite variety of salts available, the relatively minor Greenland mineral, cryolite, 3NaF.A1F3, is still the only one which gives good performance in the electrolysis. In the early days, the process was thought of as a simple one. The dissolved alumina dissociated and, during the electrolysis, the aluminum was carried to the cathode where it was discharged and collected in a pool of metal. The oxygen was carried to the carbon anode where it reacted to form primarily carbon dioxide together with some carbon monoxide. About the only virtue that can be claimed for this hypothesis is that of simplicity. The actual mechanisms must be tremendously more complex. This paper is devoted to a rather narrow part of the whole subject, namely, what ions are present in the bath, and by what mechanism the current is carried. The complexity of the literature on this system is demonstrated in Table I, which shows the ions postulated as being present during the process. This system is not easy to investigate. Cryolite melts at about 1000°C, so that all the investigations are at relatively high temperatures. Molten cryolite fumes in air, particularly if excess aluminum fluoride is present. The cryolite changes composition on heating at 1000°C, principally by reaction with moisture in the air, but apparently also by reaction with oxygen. Cryolite reacts with most of the customary materials of construction, and those that are not attacked by cryolite seem inevitably to react with molten aluminum. Graphite is the only common material that is inert to the electrolytic bath. Pure cryolite can be held in platinum. There is hope that some of the newer refractories will stand up in bath, and their development for this purpose would be a major advance in the field. The techniques to be discussed, then, are not the most advanced ones. Rather, they are examples of old standardized methods applied under difficult conditions. The principal methods that shed real light on the mechanism are density, electrical conductivity, freezing-point lowering, transport number, viscosity measurements, and reactivity of bath with carbon dioxide. The first measurement to be discussed is density. This procedure is relatively straightforward. A hollow platinum bob is suspended by fine platinum wire from an analytical balance into the melt being investigated. Density1-4 of the system sodium fluoride-aluminum fluoride is shown in Fig. 1. There is a maximum in the density near the cryolite composition, but actually the maximum is on the NaF-rich side of cryolite, close to the composition NaF - Na3AlF8. Density measurements are also useful in giving a clue to the nature of cryolite-alumina melts.1, 4 On the first addition of alumina, density decreases, Fig. 2, although the density of alumina, either solid or liquid, is higher than that of cryolite. These density results indicate that the systems are not simple. A great deal of effort has been spent in measuring the electrical conductivity of molten cryolite and of cryolite with various additives. Conductivity measurements are quite easy for fused salts that can be measured in a dip cell, but no successful dip cell has been made available yet for cryolite. Recourse is had

Jan 1, 1959

By Robin O. Williams

AN investigation has been made of the Ni-Cr system for the purpose of elucidating certain points, namely the nature of aging in both terminal solid solutions and the nature of the phase diagram. Information pertaining to solubilities and precipitation has been obtained. Experimentation Five alloys, Table I, were arc melted in a cold copper crucible using electrolytic chromium and car-bony1 nickel, both dry hydrogen treated. These 100 g buttons were homogenized 24 hr at 1300°C in dry hydrogen and air cooled. Powders were prepared by filing or pulverizing and subsequent heat treatment was done in vacuum or helium using titanium chips as a getter. Powder of —80 mesh was filed from the 60 pct Ni alloy quenched from 1000°C and was sealed in silica under vacuum using a 250 °C outgassing. After aging as indicated in Table I1 the lattice parameters were measured on the quenched samples using the standard cos" 6 extrapolation. These parameters are considered accurate to roughly 0.0001A. In all cases chromium lines of 2.8812 ± 0.0005Å at 30°C were found. Drastic quenching from sufficiently high temperatures produced very sharp body-centered-cubic lines in the first four alloys without indications of transformations. Temperatures to 1250°C were used. Solid samples less than 1/16 in. thick were quenched in water without transformation and the powders could be adequately quenched in small helium filled thin wall silica tubing using a water quench. For those powder samples which were quenched from the two phase field the relative intensity of the body-centered-cubic lines and the face-centered-cubic lines were estimated and extrapolated to give the indicated solubility data in Fig. 1. The data for the two higher alloys were somewhat limited, the plotted points being the lowest temperature where no nickel phase was found. Neither filing, abrading, pulverizing, nor cooling to —190°C produced any new diffraction lines for solid samples quenched from the single phase region, nor did the character of the body-centered-cubic lines change Single phase body-centered-cubic powders likewise did not change on cooling to —190°C. Also, samples which had some precipitation due to inadequate quenching showed no additional changes under these conditions. The first change apparent by X-ray diffraction form samples quenched almost fast enough to prevent precipitation was the diffuseness of the body-centered-cubic lines, particularly on the low angle side, For slower cooling rates the diffuse face-centered-cubic lines appeared. Work on the large grained castings showed profuse streaking through some of the Laue spots while oscillating patterns showed broad body-centered-cubic and face-cen-tered-cubic lines as well as some new lines. For the 23.6 pct Ni alloy the new lines corresponded to 2.16, 1.96, and 1.86A and were more similar in character to the face-centered-cubic lines than the body-centered-cubic lines. Samples which were air cooled gave only face-centered-cubic and body-centered-cubic lines which were still broad. One pattern indicated that face-centered-cubic (111) plane was parallel to a body-centered-cubic (110) plane. For those samples which were examined by light microscopy there were details which were not resolved. However, varied and beautiful structures were obtained. Fig. 2 is of an alloy quenched in a helium filled silica tube from the single phase region and shows particles associated apparently with dislocations which are arranged in low angle boundaries. Finer, general precipitation has also taken place within the grains. Figs. 3 to 5 show the variety of structures produced in these alloys on continuous cooling. It appears that there are four distinct modes of precipitation as evidenced by these, figures. Annealing these structures at higher tem-peratures in the two phase field gives structures as shown in Fig. 6, which shows nickel plates in the chromium matrix which reprecipitated nickel on a much finer scale of the final quench. Lower annealing temperatures and shorter times naturally give finer plates of the nickel-rich phase. Samples of the first four alloys were annealed for appreciable times between 900º and 1250°C and gave structures like Fig. 6. The relative amounts of the two phases were measured and extrapolated to give solubility data as indicated in Fig. 1. The point at 1250°C was deduced from data of Oxx.1 These and most of the other samples were checked for ferromagnetism but none was apparent. In fact, it appeared that the magnetic susceptibilities were not more than three times that for paramagnetic chromium. Discussion In Fig. 1 it is seen that the solubility of nickel in chromium can be represented by a slightly curved line on the usual log X vs 1/T plot, These data are believed to be accurate to roughly 5 to 10º. There is only fair agreement with the data of Taylor and

Jan 1, 1958

By Michel Dupuy, Daniel Calais

The study of self-diffusion of plutonium in E phase has been carried out by the welded couples method. The tracer used was puZ4O which is detected by its X-ray emission (conversion lines of uranium which are computed between 13 and 21 kev). Intensities were measured with a scintillation counter. Each layer was removed in a direction parallel to the original interface with a grinding machine and a thickness measured with a pneumatic comparator. The concentration-penetration curves obtained were corrected for the effect of heating time from room temperature to annealing temperature and for the expansion due to phase transformations of plutonium. They were analyzed by the generalized Gruzin method. Self-diffusion of plutonium in E Phase is very fast cm per sec between 500" and 620°C) and the diffusion zones are 2 to 3 mm wide for annealing times ranging from 30 min up to 10 hr. The Arrhenius law gives the temperature dependence in the form: From the point of view of self-dqfusion, PUE phase falls into the anomalous bcc metals category (Tip , Hfp, Zrp, Uy) with a low-frequency factor and an activation energy lower than those provided by standard correlations. No theory proposed hitherto to explain these anomalies (influence of dislocations, of extrinsic vacancies bonded to inlpurities, of bi-vacancies) can clearly explain the self-diffusion coeffzcients of plutonium. DIFFUSION in bcc metals is a present-day problem. A recent symposium (Gatlinburg, 1964), followed by a book,' has been devoted to it. A great many experiments seem to show that diffusion in certain bcc metals obeys unexpected laws. The activation energies measured are sometimes strangely low (B hafnium, y uranium). For certain metals (0 zirconium, p titanium) the curves of log D (D = diffusion coefficient) as a function of 1/T (T = absolute temperature) are not linear. The frequency factors Do, which are of the order of 1 sq cm sec-' in fcc metals, vary from 1 to 10~6 sq cm sec-'. Various theories have been put forward to explain these anomalies; none is yet satisfactory. We wished to introduce a new experimental result by studying the self-diffusion in c plutonium. This allotropic phase, stable from 475°C up to the melting point (640°C), is in fact bcc. Unfortunately, nothing is known of the characteristics of the point defects in this phase, which limits the scope of the hypothesis which can be made about the mechanism(s) of self-diffusion in plutonium. 1) EXPERIMENTAL METHODS 1) Principle. We used the welded couple method. The two pellets of the couple initially have different 240 isotope contents (X emitter). After diffusion, the concentration/penetration curves are drawn up by the generalized Gruzin method. 2) Gamma Spectrography. The metal used in our study is plutonium, either low in puZ4O (isotopic content 1 pct) or high in puZ4O (8 pct). The latter also contains plutonium 241 (-1 pct) and 300 ppm of ameri-cium produced by the reaction Pu2U-AmM1 + 8-. The emission spectra of these two plutoniums placed in leak-tight vinyl bags have been studied by y spectrograph~. The detector is a thin crystal of thallium-doped sodium iodide. The activity of the plutonium rich in 240 is about twice that of the plutonium low in 240 in the energy band of 17 kev (L conversion lines of uranium); this band was used in these measurements. 3) Preparation and Examination of the Diffusion Couples. Diffusion couples were made from plutonium with a high and low PU"' content. Pellets (6 6 mm. thickness 3 mm) mounted on a polishing disc with ground parallel faces were polished mechanically on both sides. In this way, pellets with two parallel faces were easily obtained. The polished pellets were joined by a 6 phase anneal (420°C, 1 hr) in a small screw press (pressure of 20 kg per sq mm cold); a centering ring enabled the two pellets to be pressed coaxially. The couples then were subjected to the diffusion treatment by annealing in the E phase in sealed silica ampules in argon at atmospheric pressure. The annealing temperatures and times are given in Table I. The couples were encased in a mild steel ring, the joint interface being thus parallel to the ground face of the ring. The diffusion couple/ring assembly underwent successive abrasions by means of a magnetic plate grinder. The thickness of the abraded layer was measured with a Solex pneumatic comparator when it was less than 0.1 mm (accuracy 0.2 p) or with a mechanical micrometer (accuracy 3 p) for passes of the order of 0.2 mm. All these operations were done in glove boxes, as plutonium is particularly toxic. After each abrasion we determined the emission spectrum of the ground face. The emissive surface is defined by means of a diaphragm 3 mm in diam. We noted more particularly the X activity in the 17-kev

Jan 1, 1969

By G. H. Gronhovd, W. H. Oppelt

Complete gasification to produce synthesis gas for manufacture of synthetic chemicals and fuels offers possibilities for utilization of the vast lignite fuel deposits in the U.S. The design of a slugging, fixed-bed, pressure gasification pilot Plant is described. Results are presented for initial operation of the plant at moderate pressure and using low-temperature char as fuel. Gasification of solid fuels is becoming increasingly important in the future overall energy picture, both in this country and abroad. Snythesis gas from gasification of coal consists chiefly of carbon monoxide and hydrogen, and after suitable purification and modification this gas can be used in the production of synthetic ammonia, methanol, higher alcohols, and synthetic liquid fuels, or as a reducing gas in the metallurgical field.' Most synthesis gas used in this country is made from natural gas, petroleum oils, and refining tail-gases, but the direct gasification of coal will become more attractive as costs of petroleum oils and natural gas increase.' A gasification process designed for use with brown coal and lignite was developed by the German Lurgi Co. prior to World War 11. In this process a fixed bed of lump-sized fuel is gasified with steam and oxygen at pressures ranging from 370 to 440 psi. Effective heat exchange between the ascending high-temperature gases and the descending solid fuel results in low gas outlet temperatures, high thermal efficiency, and favorable oxygen consumption. Lurgi gasifiers are used commercially for the production of synthesis gas or as a substitute for coal gas in many countries, including Germany, Czechslovakia, Great Britain, South Africa, Australia and Pakistan.3-6 The chief disadvantage of the conventional Lurgi gasifier which operates under nonclinkering conditions is that large quantities of excess steam must be supplied with the oxygen-steam mixture to reduce the temperature in the fuel bed below fusion temperature of the ash. Most of the steam leaves the gasifier undecomposed with the product gas and, after cooling, produces large amounts of dilute liquor. Evaluation of fixed-bed gasification experiments using dry-ash removal indicated that by increasing the oxygen concentration in the oxygen-steam blast the temperature in the combustion zone could be raised high enough to operate under slagging conditions. 7-8 Operation of a fixed-bed pressure gasifier under slagging conditions would reduce the steam requirements and the volume of waste liquor and would increase the steam decomposition, the overall thermal efficiency of the process, and the rate of gas production per unit cross sectional area of the gasifier. Because the Lurgi gasification process, modified for slagging operation, offered possibilities for efficient gasification of American lignite, the Bureau of Mines decided to investigate the process on a pilot-plant scale at the Grand Forks, N. D., Lignite Research Laboratory. DESIGN Description of Pilot Plant: A flowsheet of the Grand Forks slagging gasification pilot plant is presented in Fig. 1. The gasifier unit consits of the coal lock, the gas generator, and the slag lock. The fuel, which is periodically charged to the coal lock, moves by gravity flow into the generator and is continuously gasified by an oxygen-steam mixture introduced at the bottom of the gasifier. Molten slag is formed at the hearth and flows through a central taphole into a water quench bath. The slag-water slurry is periodically discharged from the slag lock. Process steam is generated and superheated in separately-fired, oil-burning units. Oxygen is supplied to the gasifier from a gas storage bank located some distance from the pilot plant. The capacity of the oxygen storage bank is about 130,000 standard cu ft at 2200 psig. Liquid oxygen is delivered by truck and is converted to gas during the filling operation. The superheated steam and oxygen are metered separately, then mixed and fed to the gasifier tuyeres. The gas generator is surrounded by a water jacket. The steam formed is separated in the steam drum and then discharged to the gas offtake, thus equaliz-

Jan 1, 1961

By N. Parlee, V. C. Kashyap

The solubilities of nitrogen in liquid iron and liquid Fe-Ni, Fe-Mo, Fe-V, and Fe-Mo-V alloys were measured by the Sieverts method. Measurements were made at 1600° to 1800°C on binary alloys up to 20 pet Ni, 10 pet V, 10 pet Mo; and on ternary alloys containing 0 to 3 pet V with 0 to 5 pet Mo. The results on liquid iron confirm that Sieverts' law is obeyed in the range 50 to 750 mm pressure. The measured solubilities and their temperature coefficients are in general agreement with other modern authors. The logarithms of the activity coefficients of nitrogen in the binaries are approximately linear functions of the pet of alloying element. A method suggested by Wagner, Chipman, and others for predicting gas solubilities in complex alloys from solubility data on binaries was applied to the Fe-Mo-V alloys. Reasonably good agreement was obtained between calculated and experimental solubilities. NITROGEN'S solubility in liquid iron has been studied by a number of investigators. It is reasonably well established that the solubility of nitrogen follows Sieverts' law at least up to 1 atm partial pressure and that the solubility increases gradually with temperature. The solubility of nitrogen in Fe-X binary liquid systems has been investigated in only a few cases. Only the systems Fe-Cr,3-5, 7 Fe-V,3 Fe-Mn,3, 5 Fe-Ni,3, 5 Fe-Si,B, H Fe-C, L, H and Fe-P4 appear to have received any study. The only work on liquid Fe-V was done by Brick and Creevy.3 This was limited to 13.5 pet and 26.5 pet V, but no exact temperatures were recorded. No work whatsoever appears to have been done on liquid Fe-Mo alloys and even work on Fe-Ni alloys is rather scant. The work on liquid ternary systems is still more limited, and the only publication available appears to be that of Wentrup and Reif,7 who studied the Fe-Cr-Mn and Fe-Cr-Ni alloys. Rassbach, Saunders, and Harbrecht17 have reported work on the solubility of nitrogen in stainless steel but this was not a systematic study of any particular system. Commercial alloys usually contain several alloying elements. Thus, it often becomes important to be able to predict the nitrogen solubility in systems containing two or more added elements without the necessity of making measurements. Wagner,14 Chipman," Darken and Gurry," and Morris and Buehl 14 have suggested means by which this may be accomplished, and Langenberg14 has recently applied one of these methods to nitrogen solubility in complex liquid alloys. This paper reports the results of nitrogen solubility determinations on Fe-Ni, Fe-Mo, Fe-V, and Fe-Mo-V alloys and compares calculated and experimental solubilities in the ternary alloy. Attempted measurements on Fe-Cr alloys were not successful by the experimental method employed. Experimental Method The general method of solubility measurement was that of Sieverts.' The apparatus and procedure were essentially the same as used by Liang, Bever, and Floe."' The equipment consisted of a small vacuum furnace heated by a 6 kw induction unit, gas measuring apparatus, and a gas purification train. The crucibles used were Norton Alundum with alumina sand around them for insulation. The crucibles were charged with 100 to 200 g of material, about 180 g or nearly filling the crucible being found most satisfactory. Hot volumes were determined with argon and ranged from 95 to 130 cu cm (stp). Temperature measurements were made with a Leeds and Northrup optical pyrometer which was calibrated periodically against the melting point of iron in the same apparatus."-'* Good quality nitrogen, hydrogen, and argon gases were further purified and dried in standard purification trains. The sources of the high purity iron and other alloying elements used were as follows:

Jan 1, 1959

By William Babcock

Augered, Cast-In-Place (ACIP) piles can be an economical, reliable, versatile foundation system. They have also been a part of projects that were behind schedule and the subject of lawsuits. The ACIP pile is a specialty system that is more workmanship dependent than most deep foundation systems and is especially vulnerable to the problems and abuse of poor specifications and contract language. Many of the original specifications were based on grouting methods, and numerous misconceptions have followed the method. The Deep Foundations Institute (DFI) has been the leader in debunking the mystique that has hovered over the method and attempted to standardize the industry through publication of the manuals describing the method and how it should be inspected. DFI should be applauded for taking the lead and producing a reference document that can be used to educate the specification writers, designers, inspectors, and owners. It must be must appreciated that there have been other organizations that would not acknowledge ACIP piles as a legitimate member of the deep foundation family. Some consultants and designers have gone to the extreme of making it policy to not recommend the method for use. This presentation is one practitioner's view of the causes of problems as they can be traced back to the contractual conditions. It is intended to provide a broader and different perspective than those provided by the technical specialists. It does not necessarily reflect the position of the DFI or any of the organizations associated with the ACIP pile industry. It is intended to further the spirit of partnering on every ACIP pile project, to further the acceptance and promote the use of this unique system, for the benefit of all the parties. It should be recognized, however, that all of the participants can and do play a role in getting a project into trouble. My view is that projects that get into trouble usually have an early flaw that leads the project to the edge, and the project participants blindly follow the original mistake right over the cliff like lemmings. This instinctive reaction may be a survival tactic by going along with the group, because any one party that departs from the program or shows a position of weakness is a candidate for sacrifice.

Jan 1, 1997

By W. N. Hoskins

This report covers the final results of a two-phase contract study conducted between July 1974 and October 1976. A comprehensive summary of the initial phase of the study is included. Phase I of the study involved the investigation and evaluation of all potential candidate underground systems for mining the deeper deposits of oil shale and associated minerals in the Piceance Creek basin of northwestern Colorado. Phase II called for the refinement and the detailed technical and economic analysis of the most promising system, or systems, thus disclosed. Of the several systems initially investigated and evaluated, four showed considerable merit for exploiting the deeper deposits: (1) chamber and pillar mining with spent shale backfill, (2) sublevel stoping with spent shale backfill, (3) sublevel stoping with full subsidence, and (4) block caving mining using LHD's. Final refinement and analysis of these four systems indicated their technical feasibility over at least part of the range of conditions expected in the deeper deposits. Their economic feasibility also was indicated under certain operating and market conditions. A variety of engineering, production, and cost information is provided on each of these systems.

Jan 1, 1976

By W. N. Hoskins

This report covers the final results of a two-phase contract study conducted between July 1974 and October 1976. A comprehensive summary of the initial phase of the study is included. Phase I of the study involved the investigation and evaluation of all potential candidate underground systems for mining the deeper deposits of oil shale and associated minerals in the Piceance Creek basin of northwestern Colorado. Phase II called for the refinement and the detailed technical and economic analysis of the most promising system or systems, thus disclosed. Of the several systems initially investigated and evaluated, four Showed considerable merit for exploiting the deeper deposits: (1) chamber and pillar mining with spent shale backfill, (2) sublevel stoping with spent shale backfill, (3) sublevel stoping with full subsidence, and (4) block caving mining using LHD's. Final refinement and analysis of these four systems indicated their technical feasibility over at least part of the range of conditions expected in the deeper deposits. Their economic feasibility also was indicated under certain operating and market conditions. A variety of engineering, production, and cost information is provided on each of these systems.

Jan 1, 1976

By John De La Vergne, Morri Medd

"This paper describes the sinking of a circular concrete ventilation shaft through 110feet of water-bearing overburden. The brine circulation freezing method was used to stabilize the walls during excavation. In order to take advantage of the cold winter weather, a custom-built heat exchanger (natural radiator) was installed in place of the standard mechanical refrigeration plant.IntroductionIn the late fall of 1979, Les Mines Selbaie awarded a contract to the firm of 1.S. Redpath Limited to sink a ventilation shaft on its property in northwestern Quebec. The shaft was to be sunk through 110 feet of water-bearing overburden and approximately 90 feet of rock to a final depth of 200 feet below surface. The water table was measured at 16 feet below the surface elevation.After examining the soils report and diamond drill core from the shaft area, Redpath came to the conclusion that freezing was the best way to stabilize the overburden for sinking. LocationThe mine site is 420 statute miles due north of Toronto, just east of the Ontario/Quebec border (Fig. 1). Access to the site is provided by a development road built by the Quebec government from the Matagami/lames Bay Highway. History of Ground Freezing In the Mining IndustryIn 1862, shortly after the development of mechanical refrigeration, a mine shaft was sunk through an artificially frozen water-bearing formation in the United Kingdom. The first application of ground freezing in North America was for a Michigan iron ore shaft in 1888. Since that time, the freezing method has been used to sink hundreds of shafts throughout the world. Its best known application was to sink sixteen shafts through the Blairmore Formation in Saskatchewan.The same method has been used in every case. It involves chilling a calcium chloride brine solution and circulating the brine in concentric pipes, spaced between 3 and 6 feet around the shaft perimeter and usually 4 to 5 feet from the limits of the proposed shaft excavation."

Jan 1, 1982

By J. S. Pascover, J. K. Abraham

The influence of the early stages of precipitation on the kinetics and structure of martensite formation in Fe-27Ni and Fe-29.5Ni alloys containing from 0 to 10 pct Ti was examined with X-ray and electron microscopy techniques. The formation of a coherent, ordered preprecipitate had a profound stabilizing effect on the austenite. The Ms was decreased by increased titanium content and aging time up to a critical time. When the critical aging time was exceeded, the Ms was observed to increase markedly. The formation of the clusters was insuppressible and the volume fraction of clusters formed during the quench was a function of the titanium content. Martensite resulting from transformation of the clustered austenite is tetragonal with the c/a ratio increasing with titanium content. A model for the tetragonality is suggested. The morphology and substructure of the m artensite is inter-preted in terms of the above information and the cur-rent models of twinned martensite. ThE ramifications of precipitation in austenite to the properties of austenite have been the subject of numerous investigations. The current research is concerned with the influence of precipitation in austenite on the kinetics and structure of subsequent marten-site formation. In a previous investigation, Abraham et al.1 followed the aging reaction in an Fe-29.5Ni-4.2Ti* (at. pct) alloy using an X-ray diffraction technique. This technique, employing a Guinier camera, provided kinetic measurements through observation of the side band position as a function of aging time. The salient results of this work were: 1) The initiation of precipitation was not suppressed by quenching, i.e., there was a finite cluster zone size at zero aging time; and 2) The hardness of the aged austenite correlated extremely well with the zone size. During the previous work it was noted that the mar-tensite formed after aging was tetragonal, substanti-ating an earlier observation.2 Systematic investiga-tion revealed that the martensite was tetragonal in both the solution-treated then quenched, and the solu-tion-treated, aged, and quenched condition, and, furthermore, that a marked stabilization of the austenite occurred as a function of aging time. The present work is concerned with documenting the tetragonality and the stabilization phenomena as well as the ob- served microstruction with a suggested rationale for the behavior noted. EXPERIMENTAL PROCEDURE The compositions of the alloys are listed in Table I. The analyses were performed after the solution treatment of the strip material. Nickel was determined using the standard dimethy1-glyoxime procedure whereas titanium was determined colorimetrically with hydrogen peroxide and volumetrically by titrating with ferric iron. The materials were melted in a 5-lb vacuum induction furnace, cast into 2-in.-diam ingots, and forged in a temperature range of 950. to 1200°C to 1/2-in. slabs. The three higher titanium containing materials cracked during forging; therefore, to get the alloys into strip form, slices 1/8 in. thick were cut from the slab, homogenized 4 hr at 1150°C, then cold-rolled to a 0.04-in. thickness. The remaining slabs were hot-rolled, homogenized 4 hr at 1065"C, then cold-rolled to a final thickness of 0.03 in. All of the heat treatments were performed under a protective atmosphere of argon. The Ms temperature for most of the alloys is below room temperature; therefore, it was possible to solution treat, quench to room temperature, polish, and then observe the transformation optically on a cold-stage microscope. To determine the effect of aus-tenitizing temperature on Ms, eight of the alloys were treated at two temperatures, 1025" and 1120°C. No measurable variations in Ms were noticed. The remaining alloys were treated at 1025°C. The specimens, : by 5/16 by 0.03 in., were austeni-tized in a vertical tube furnace under a dynamic argon atmosphere. The bottom of the tube was submerged in water for quenching purposes. The question of stabilization that may be operating at room temperature was investigated and found to be negligible. Many of the specimens were held at room

Jan 1, 1970

By J. P. Sheehan, W. R. Hibbard, M. Baeyertz

This paper deals with molybdenum modifications of 5140 steel that have the same hardenability but a better tolerance for phosphorus than the AISI-SAE 5140 grade. Lack of toughness in steels with higher than normal phosphorus contents is well known to metallurgists. This problem is troublesome even within normal phosphorus ranges, if the heat treatment or the design of the part or the service is critical. Under such unfavorable conditions and also in the case of phosphorus contents toward the upper side of the commercial range, the use of molybdenum to replace a part of the chromium in 5140 steel provides a factor of safety. The toughness of steel is variously exhibited in different mechanical tests; broadly the term is applied to the capacity of the steel to deform prior to fracture. Defined in this way, toughness is considered to be an inherent quality that depends upon the composition and structure of the steel, and also upon its temperature during deformation and fracture in the test. In the present state of our knowledge, the type of mechanical test needs to be included in any discussion of toughness, because the revelation of this quality in steel depends on the stress state and rate of stressing imposed by the test. In comparing the toughness of one steel with another by laboratory testing, it has long been customary to use notched tests that impose severe constmint to deformation, and then to test over a range of temperatures to obtain the so-called transition. At temperatures above the transition, the steel fails after considerable deformation and absorption of energy. Below the transition, less energy is absorbed as the steel fails largely by cleavage. The transition range itself is characterized by a more or less abrupt change in energy absorption and type of fracture. The conventional V-notch Charpy impact test has been used exclusively in the work covered by this report. For the steels under study, rather sharp transitions are obtained with this test, at testing temperatures that are easily obtained in the laboratory. The position of the transition on the testing temperature scale provides a rather sensitive index of the toughness of the steel, when the steels under study are similar in character as they are in this work. Turning to the metallurgical reasons for the greater toughness of one steel as compared to another, the authors propose to limit the discussion to the small field under study. Only one structural state is considered, tempered martensite of a hardness of about 28 Rockwell C or 269 Brinell. The study deals first with the loss of toughness in AISI-SAE 5140 steel caused by increasing the phosphorus content from about 0.020 to 0.040 pct. A second part of the work deals with counteracting this loss in toughness by replacing a part of the chromium by molybdenum. A series of molybdenum modifications was studied, in each of which the chromium was reduced sufficiently to duplicate the hardenability of 5140 steel. Phosphorus affects the toughness of steel in two ways. An inherent lack of toughness of phosphorus-bearing ferrite as compared to low phosphorus ferrite has often been noted. Jolivet and Vidall have shown that phosphorus has the same effect in tempered martensite in chromium steels. The other well known effect of phosphorus is to make steel susceptible to temper embrittlement. Temper brittleness is a loss in toughness brought about by tempering steel within a limited temperature interval somewhat below the A1 temperature. In most of the standard AISI-SAE alloy steels, this temperature interval is approximately 850-1100°F. Either of these types of loss in toughness is easily followed by the shift in the transition temperature obtained with the notched-bar impact test. The data to be presented show the beneficial effect of substituting molybdenum for a part of the chromium in 5140 steel with either moderate (0.020 pct) or high (0.040 pct) phosphorus contents. Both the inherent lack of toughness of phosphorus-bearing steel and temper brittleness are counteracted by this use of molybdenum. The work of Jolivet and Vidal mentioned above shows the detrimental effect of phosphorus on the toughness of tempered martensite in the absence of temper embrittlement, as well as the temper brittleness caused by phosphorus. They used two steels, essentially 0.25 pct C-1.4 pct Cr, with 0.044 and 0.013 pct P, respectively. The nonembrittled state was obtained by quenching in oil from 1610°F, then tempering for one hour at 1200°F and quenching in water. In this state the transition temperature range of the low phosphorus steel in the notched-bar impact test was below that of the steel with 0.044 pct P. An additional treatment of 24 hr at 975°F (that is, in the embrittling range) caused both steels to lose toughness, but the high phosphorus steel showed the greater embrittlement. Recently Hollomon2 has published a comprehensive survey and bibliography of the literature on temper brittleness, to which the reader is re-

Jan 1, 1950