Search Documents

By T. Lu

Microwaves have considerable potential as an energy source in both mineral processing and metals extraction. In this research, the utilization of microwave radiation for the heating of a gibbsite type bauxite ore was investigated. Firstly, thermogravimetric studies were performed in order to characterize the dewatering processes of the ore. Secondly, both the real and the imaginary permittivities, which are the fundamental properties that determine the interaction of microwaves with any given material, were measured for the bauxite ore as a function of temperature. The changes in the permittivities were shown to be related to the dewatering processes. Subsequently, the effects of operating variables such as processing time, sample mass, particle size, microwave power, sample bulk density and carbon and magnetite additions on the sample temperature in a microwave field were studied. The results showed that under suitable conditions the bauxite ore could be readily heated. Therefore, there is considerable potential for the application of microwaves for the heating of bauxite ores.

Jan 1, 2007

By J. M. WADSWORTH

The purpose of this bulletin is to describe the methods of constructing and operating representative types of plants in the United States used for removing the light hydrocarbons from petroleum by continuous distillation, such plants being commonly known in the trade as topping or skimming plants. In the discussion of each plant an endeavor has been made to arrange the text similarly in order to facilitate comparison and to emphasize the important features. The various experimental values for the specific and the latent heats of the oils apply approximately to the oil treated. Careful experiments with each oil and its commercial fractions were not justifiable in view of the purpose of this report. It is regretted that limitations for recording data at the different plants made impossible the determination of a heat balance for each, which would have provided an equitable method of comparing efficiencies. The writer has confined himself to a comparison of the relative efficiencies of the distilling apparatus alone by the following method: Effi . f till d tt" _ Heat theoretically required. ciency 0 SIS an se mgs - Heat content of fuel consumed. The plants described are all in California where the topping industry has had its growth accentuated by the character and the use of the oil handled. The scarcity of suitable coal made the adoption of other fuel necessary, and the heavy oil of California supplied the need. To raise the flash point and to dehydrate this oil, various plants have been developed. However, the topping industry is represented in other fields; the Roxana Petroleum Co. of Cushing, Okla., and the Warner-Quinlan Asphalt Co. of New Jersey, are operating Trumble plants, and Texas and Oklahoma operators have been experimenting with different pipe retorts for continuous running. In addition to the reasons for topping cited above, in California topping has other purposes which give the plants practically a universal field in the oil industry. These additional purposes are (1) to remove the lighter constituents of the oil prior to storage for a long period, thus reducing the losses from evaporation, (2) to dehydrate and clean the oil, and (3) in conjunction with a complete refinery, to remove the lighter fractions cheaply and quickly, leaving a residue to be rerun for lubricants, coke, and other products. The reader in studying a plant for possible adaption to his own use should note that local considerations enter into the design and size of a plant. Several questions present themselves, as follows: 1. What type is suitable for the oil? 2. How much money is available for construction? 3. Will the volume of residuum be large enough for heat exchange with the crude? 4. Can the heat content of the vapors be used to reduce the cooling-water requirements? 5. What method will best recover the heat from stack gases? 6. Are the various pieces of apparatus adequate in size and best adapted to their purpose? 7. Is every possible provision made for the recovery of waste heat? 8. What products will be made, and what volume of each? 9. Is there provision for the recovery of light vapors? 10. Will the saving of fuel justify the capital and maintenance charges on the regenerative apparatus contemplated? It is regretted that information concerning the operation of topping plants with eastern and Middle West oils is not available. The writer carefully canvassed the Middle West, but did not find a plant where operation had progressed beyond the early experimental stages and reliable figures could be furnished. The reader will find fuel economy and heat recovery emphasized throughout the descriptions. The conservation of the available petroleum supply is of the utmost importance, and the Bureau of Mines presents this paper to encourage the hearty cooperation of operators to that end. The Baume gravity scale used throughout the report is that of Tagliabue with a modulus of 141.5 for conversion to specific gravity.

Jan 1, 1919

By K. E. Waters, J. E. Nesset, F. Rosenblum, R. Langlois, J. A. Finch

"Some sulphide mineral mixtures when exposed to air and a warm and humid environment can exhibit a self-generating temperature rise, referred to as self-heating or spontaneous heating. The observed self-heating derives from the oxidation reactions of the active sulphides. In previous publications by the authors, it was proposed that the self-heating of sulphides proceed in three distinct stages; namely, Stage A, Stage B and Stage C. In Stage A (<100OC) the sulphides, in the presence of moisture are oxidized, generating heat through a series of sequential reactions and forming elemental sulphur as one of the products. In Stage B (>100OC) the elemental sulphur produced in Stage A is further oxidized to generate additional heat and SO2. Stage C (>~380OC), sometimes referred to as thermal runaway or roasting, is not addressed in this paper. This communication focuses on the type and role of elemental sulphur found in Stages A and B, and the sequence of reactions that is occurring in Stage A. The sequence is divided into two phases, the first based on galvanic interaction between the sulphide minerals that generates an acidic environment but little heat, and the second involving the production of H2S which rapidly oxidizes to produce heat and elemental sulphur. To date, data suggest that the primary oxidation product formed in Stage A is the stable orthorhombic a-S8 form of elemental sulphur. Above 96OC the a-S8 transforms to a monoclinic ß-S8 structure which is less stable and will readily oxidize to generate heat and SO2. Above 159OC a proportion of the ß-S8 sulphur will transition to a polymeric Sµ form of sulphur which can readily volatilize. INTRODUCTION Some particulate and granular materials, when exposed to appropriate atmospheric and physical conditions, can exhibit a self-induced temperature rise resulting from accumulated heat due to internal exothermic oxidation reactions. This phenomenon is commonly referred to as self-heating or spontaneous heating. Under favorable physical and environmental conditions, these reactions can elevate the temperature of a given material from ambient to the point of auto-ignition. Self-heating behaviour should not be equated to pyrophoric behaviour which describes a group of materials (e.g. certain finely powdered metals) that will ignite spontaneously in air below 55OC. There are numerous materials such as coals, hay, forestry wood products, food products to name a few that can exhibit self-heating behaviour. This publication continues the focus of the authors on the self-heating of sulphide mineral mixtures. Many of the metals of commercial use found in nature are in the form of these sulphides which must be mined, crushed, ground and concentrated prior to smelting or hydrometallurgical processing in order to produce primary metal. The issues of sulphide self-heating therefore pertain to the mining and processing of metals."

Jan 1, 2018

By Foster Fraas

Almost all minerals show irreversible changes in electrical conductivity after heating in the temperature range 100° to 800° C. This effect can be detected with only a limited number of minerals with the standard ionizing-electrode-type separator, which differentiates between nonconductors and conductors in the single-particle resistivity range of 1011 to 1013 ohms. Tests outside this range with other type separators, such as the static field type, increase the number of minerals with which the effect can be detected to almost all that were tested. Irreversibility may be the result of an alteration of adsorption layers, volatilization of surface cations or anions, or an oxidation or reduction. One example is limonite, which decomposes to hematite and passes through two minima and two maxima in conductivity in the temperature range 100° to 900° C.

Jan 1, 1959

By Mehmet Guney

Acceptable working environments in production areas and service openings of Mindola Mine on the Zambian Copperbelt are currently maintained with an air volume of 1000 cu m/s and 5500 kW of installed refrigeration plant. It is planned to open up additional deeper areas of the mine for future production. Temperature problems, due to the increased heat generation from various underground sources are recognized as potential hinderances to efficient production. Findings of research work indicate that the present total heat output of 58,000 kW will inevitably increase by the second five-year period of the deepening program to 52,900 kW and by the fifth five-year period to 63,200 k\V. Estimated WB and DB temperatures, representing the total heat generation in stope faces and development headings during these same periods are predicted to increase to 53.8/40.2 °C and 35.5/42.1 °C respectively. It is assessed that the nominal refrigeration capacity needs to be progressively increased to 9,000 k\V This paper deals with the thermal problems in Mindola Mine, current heat output calculations, future prediction of temperature and heat load in various working areas of the mine with the application of computer programs and interpretation of data in order to find the effective solution for long-term planning of ventilation and air-conditioning.

Jan 1, 1982

By S. S. Venkata

This volume describes a comprehensive program of research into the reliability of mine electrical power system components and the resultant reliability of the total system. The research effort encompassed analytical models, laboratory testing and field testing. The analytical work included definition of terms, fail rate functions and distributions, failure rate estimation and techniques and procedures for theoretical reliability assessment. One of the primary mine power system components addressed in the study was the ac molded case circuit breaker. This device is known to have low reliability and hence an unfavorable impact on mine safety and productivity. Ac molded case circuit breaker reliability was studied by analytical means, laboratory testing and field monitoring. A similar three-pronged&apos; effort was made to study the reliability of undervoltage relays/releases. Particular emphasis was placed on new solid state undervoltage relays. The reliability of bulk power components, such as trailing cab les, motors, control gear, and other equipment, was assessed by gathering maintenance records from active mines. These data were compared to similar records from other industries. The work was extended to include the reliability, availability, maintainability and safety of these components.

Jan 1, 1979

By H. Stuart Auvil

Twelve samples of run-of-oven coke were taken at coke plants in the United States and Canada. Sampling procedure was directed toward obtaining the highest possible degree of uniformity in the gross samples, so that variations in results caused by sampling variations were at a practical minimum. Under these conditions the standard deviation of the screen analysis test on 500-pound samples is found to range from 1.2 percent for the 1-inch screen to 4.5 percent for the 5-inch screen. At present, the A.S.T.H. standard method of test requires that results be reported to the nearest 0.1 percent. This implies a higher than actual degree of precision, and revision of the report required by the method is suggested. Much larger Samples than are generally tested are required to reduce normal testing errors to a point where they are not appreciable fractions of the total variations found in a smoothly operating plant. For example, it is deduced that over 100,000 pounds of coke must be screened to determine if ordinary day-to-day variations in screen analysis have appreciable effects on the performance of a blast furnace.

Jan 1, 1950

By J. A. Ehler

Speed and torque control of standard A.C. induction motors can be accomplished using a variety of devices ranging from mechanical, hydraulic, and electrical. Also, the motor can be specified as an A.C. wound rotor or D.C. motor using the associated controls. Normally, any one of these drive types can be adequately used to provide the torque control necessary to accelerate a conveyor belt system. The selection will depend on the economics, experience, and preference of the designer or end user. These drive types will be presented from a functional and performance viewpoint to assist in the understanding of the available technology.

Jan 1, 1998

By Henry Kreisinger, WALTER T. RAY

This bulletin contains a statement of certain results that will be embodied in a report describing investigations of the combustion of fuel made by the United States Geological Survey and the Bureau of Mines in a specially constructed long furnace. The furnace forms part of the fuel-testing plant at Pittsburg, Pa., which was established and equipped by t.he Geological Survey, but passed under the control of the Bureau of Mines on July 1, 1910, when a t.ransfer of fuel-test.ing investjgations, authorized by act of Congress, became effective. The work discussed in this bulletin was done under the direction of the Geological Survey. The furnace was designed and built for an experimental study of the processes of combustiop, this study being part of a comprehensive plan for testing fuels to determine their heat value and the manner in which they can be used to best advantage. Although the main object of the researches made with the furnace by the Geological Survey was to examine critically the production of sensible heat by combustion along the path of the gases rising from the fuel, an interesting as well as important side problem developed in the study of the simultaneous dissipation of the heat through the walls and roof . of the furnace. Thus incidental data were collected on the temperature gradient through the walls at several places. These temperature data. (together with the heat conductivity of the material of the walls) formed the basis for calculating the heat dissipated through the walls. The object of this report is to present and discuss these temperature data. The discussion particularly concerns the air-space type of wall construction as compared with the solid brick wall or walls type, in which the air space is filled with some solid material of low heat conductivity. The conclusion of the authors, which perhaps will surprise some readers, is that, so far as loss of heat is concerned, a solid wall of brick or any ordinary material is preferable to a hollow wall of the same total thickness, especially if the air space in the hollow wall is near the furnace side. There is a general belief that l?ince air is a poor conductor of heat, air spaces built into the walls of a furnace will prevent or reduce heat dissipation through the wa.lls. Although there may be instances of furnace walls in which such construction reduces the rate of heat flow through them, yet as a rule the effect of the air space is just the opposite. While the heat does travel very slowly through the air by conduction, it leaps over the air space readily by radiation. Although this latter mode of heat propagation is common in nature, the laws governing it are not generall;y known and are seldom taken into consideration when furnace walls are being designed. It may be stated here that the quantity of heat passing through a. portion of a solid wall by conduction depends on the difference between the temperatures of the two planes limiting the portion of the wall. The quantity of heat that passes across the air space in the waH depends on the difference of the fourth powers of the absolute temperatUI: es of the surfaces inclosing Hie air space. It follows that, in case the heat. passes by conduction through the solid'portion of the wall, the loss remains approximately the same so long as the temperature of the two limiting planes remains constant, no matter what may be the temperature of the two planes. On the other hand, the heat passing across the air space by radiation increases rapidly with the temperatures of the inclosing surfaces, although the difference between these temperatures may remain constant. This feature will be shown by curves in the latter part of this paper and thoroughly discussed. The important point is that the air space, which is advantageous in the walls of a refrigerator because the temperatures are low, is objectionable in a furnace wall because the temperatures are high. It is customary to put air spaces in furnace walls between the firebrick linings and the common brick. Usually the fire-brick lining is only half a brick thick, which construction brings the air space too close to the furnace. The result is that the temperatures of the surfaces inclosing the air spaces are too high, and in consequence too much heat is radiated across the spaces. The heat passing through such walls would be much reduced if the air spaces were filled with brick, or, better, with some cheap nonconducting materials, such as ash, sand, mineral wool, etc. Even where the fire-brick lining is one brick thick (9 inches), the temperature in the furnace may be high enough to raise the temperatures of the air-space surfaces so much that the heat radiated across the space will amount to more than would the heat conducted through a filling, were the filling only common brick. This last statement is amply justified by the data here presented.

Jan 1, 1911

"In this paper, a mobile heat treatment furnace from Akkermans Gloeitechniek, a Dutch company, was simulated with Computational Fluid Dynamics (CFD). The furnace is cylindrical with four oil burners, and large metal products such as dredging pumps and impellers can be flexibly heat treated to obtain required microstructure and mechanical properties through stress relief, annealing, hardening and tempering. The furnaces are exposed to the open air, and thus the heat loss becomes significant and varies from day to day and from season to season. Since the temperature of the metal products to be heat treated can only be measured on the surface, the temperature evolution inside the metal could not be tracked in practice. CFD simulation provides a useful tool to predict the temperature evolution within the metal pieces and within the combustion space of the furnace. Energy distribution and heat loss can be subsequently estimated. An overall energy balance through temperature measurement indicted relatively low energy efficiency. Especially during the soaking period, the high energy supplied is barely used to compensate the heat loss of the furnace to maintain a constant temperature of the metal piece. The current CFD modeling aims to give advice on how to modify the design and optimize the operation to reach higher energy efficiency and low heat loss. The CFD model consists of turbulent combustion model, radiation model in participating media, and conjugate heat transfer between the combustion space and solid metal. Temperature measurement was carried out to provide thermal boundary conditions and overall energy balance of the operation. After the model validation with temperature measurement within the combustion space and metal surfaces, furnace optimization will be conducted.IntroductionHeat treatment is a common practice in metal production and manufacturing industries. Through heat treatment at certain temperatures with special patterns, unique mechanical properties of the metals and the metallic products could be obtained. ""Akkermans Gloeitechniek"" is a company situated in K.inderdijk, at location of LHC-Holland (www.ihccaland.com), the Netherlands. Heat treatment of metals is its core business. Various type of heat treatment are applied, such as stress relieving, soft annealing and hardening (quenching), tempering, transformation and precipitation. At the company 6 furnaces are in operation and the 7th is being built"

Jan 1, 2004

By Shantaliu S. Shevade, Muhammad M. Rahman

"This paper presents a systematic analysis of fluid flow and heat transfer processes during the magnetic heating of the substrate material. Heat is generated in the substrate material when a magnetic field is imposed due to change in orientation of the molecules. As a result, the substrate temperature rises. The i;tudy considered microchannels with rectangular and square cross section with heat generation in the substrate due to imposed magnetic field. The results computed were for Gadolinium substrate and water as the working fluid. The purpose of this study is to explore the transient heat transfer coefficient when the fluid is circulated through the substrate via microchannels. Equations governing the conservation of mass, momentum, and energy were solved in the fluid region. In the solid region, heat conduction was solved. From the simulation results, plots of Nusselt number and heat transfer coefficient were obtained over the length of the channel. A thorough investigation for velocity and temperature distributions was performed by varying channel aspect ratio, Reynolds number, and heat generation rate in the channel. It was found that the peripheral average heat transfer coefficient and Nusselt number is larger near the entrance and decreases downstream because of the development of the thermal boundary layer. With the increase in Reynolds number, the outlet temperature decreased and the average heat transfer coefficient increased.IntroductionMagnetocaloric effect (MCE) is the heating or cooling of the magnetic materials due to varying magnetic field. The effect was originally discovered by Warburg. Magnetocaloric materials store heat energy in the way the atoms vibrate and in the way electrons spin within each atom. More heat energy increases the vibrations and also makes the spins more random. When a strong magnetic field is applied to a magnetic material, the magnetic moments of its atoms become aligned making the system more ordered. The more ordered material has lower entropy and compensates for the loss by heating up. When the magnetic field is removed, the magnetic moments return to their random directions, entropy increases and the material cools. Gadolinium is a magnetic material that exhibits high temperature rise during adiabatic magnetization around its transition temperature of 295 K. It has been experimentally observed that adiabatic temperature rise increases with magnetic field strength and can be as high 20 K when a magnetic field of IO T is applied. Thus magnetic field, when applied to a microchannel heat exchanger, causes temperature change in the magnetic material. The fluid flowing through the channel gets cooled or heated due to this adiabatic temperature change."

Jan 1, 2004

By Iina Vaajamo, Jani Jansson, Lauri Pesonen

In pyrometallurgical operations, structural integrity of a high temperature furnace plays a crucial role in the overall safety, profitability and ecological footprint of the plant. Furnace integrity is related to how reliable a furnace is and it can be compromised, for example, by having poor operating and maintenance practices, an inefficient cooling system and flaws in the overall furnace design. These flaws and poor practices might lead to unexpected shutdowns, production losses, increased emissions, or worse. This paper presents the main factors to consider when engineering a furnace and developing its operating practices, while ensuring safe and reliable operations without compromising process efficiency and quality of the final products. In this respect, Outotec’s solutions for the cooling system and for automation systems like PROSCON, Process Advisor, Sentinel and our Smelting Information Management System, are also introduced.

Jan 1, 2015

By A. R. Taylor Jr.

The heat capacities of a-quartz form beryllium fluoride were measured at approximately 3° intervals from 8° to 300° K., using an adiabatic calorimeter. At 298.15° K the heat capacity and entropy were 12.39 cal/deg mole and 12.75 ±0.04 eu respectively. Enthalpy measurements were made with an ice calorimeter at approximately 30° intervals on the quartz and glassy forms of beryllium fluoride between 300° and 1,200° K. A melting point of 825° K and an 0,-8 type transition at 500° K with a heat effect of 75 ca1/mole were deter-mined from the enthalpy data for the quartz-type sample. Beryllium fluoride glass crystallized spontaneously into the quartz modification at 500° K. The heat of the reaction BeF2 (a-quartz) .... BeF2 (glass) was found to be 1,125 ±16 cal/mole at 298° K by solution calorimetry. This value, when corrected to 273° K, was used to correct for the heat absorbed by the formation of glassy BeF2 when the sample was dropped into the ice calorimeter from temperatures above the melting point. Using corrected enthalpy measurements, the heat of fusion was determined to be 1.13 kcal/mole at 825° K.

Jan 1, 1965

By E. C. W. Perryman

Materials research and development has played an important role in the commercial success of the CANDU- PHW nuclear reactor and in the production of heavy water. Both capital investment and energy conservation demand very high component reliability in such systems. The interactions among reliability, plant performance and economics will be discussed in relation to materials research and development. Likely materials requirements for the nuclear industry over the next twenty five years will also be discussed.

Jan 1, 1977

By K. Karaman

This study investigated the effect of surface roughness on Schmidt rebound hardness (RL). Four different test surfaces of rock samples were studied: natural, ground, cut surfaces, and core samples. There was significant variability of standard deviation based on the RL on the natural surface, which indicated high roughness of the rock surface, whereas surface polishing caused a significant decrease in standard deviation. ISRM and ASTM methods were compared to estimate unconfined compressive strength (UCS) for different testing surfaces. RL obtained from the cut surface was found to be more reliable than those obtained from other testing surfaces for the prediction of UCS; however, regression and ANOVA analyses revealed that the ISRM method gave a more accurate UCS estimation of rocks with highly rough surfaces. It was also shown that RL values obtained from a cut surface were significantly higher than those obtained from core samples. Therefore, a comparison between RL values obtained from core samples and cut surfaces was made based on previous studies. This study statistically showed that estimated UCS values are not statistically significant if Schmidt rebound tests are not performed on similar surfaces. In addition, the mineral grain sizes of the studied rocks, different testing surfaces compared with those in literature, and standard deviation from RL are evaluated and discussed. The Schmidt hammer technique is a rapid, inexpensive, and straightforward method for estimating UCS for preliminary assessment; however, roughness of the surface should be eliminated if variations are shown in the surface rebound hardness.

Apr 14, 2024

Gus C. Henning, New York City: In taking up the discussion of these specifications it is necessary that I give definitions of what I understand under the term " Specifications." There may be three kinds, viz.: (1) Specifications in general; (2) Standard Specifications; (3) Standard International Specifications. 1. A Specification is a document used in commerce which should clearly define the qualities of material to be supplied by the producer, the tests which shall be applied for their determination, and the methods which shall be applied for the purpose of determining that the entire product shall possess such qualities, properties and finish as are desired. The terms used in such document must be applied in accordance with their strict technical definitions as used by those most conversant with them, and the language should be of such accuracy that there can be but a single interpretation of each and every clause. A specification is a part of a contract, and should be legally perfect and accurate. Inaccuracy of definition and dic-

Jan 1, 1903

This report presents information developed during Bureau of Mines contract H0242016, "Mine Shaft Fire and Smoke Protection Systems" from May, 1974 through June, 1975. Purpose of the metal and nonmetal health and safety project was to evaluate mine shaft fire and smoke hazard problems, and to develop and demonstrate a low-cost, reliable mine shaft fire protection system that would protect against such hazards and would be applicable to a majority of metal and nonmetal mine shafts, including raises and winzes, especially in deep mines. Program effort proceeded through five phases, culminating in the successful in-mine fire demonstration of a prototype system. In addition to this final report, a film is available which depicts components of the system and its successful shaft fire testing at an underground mine.

Jan 1, 1975

Hydraulic fluid power systems are advantageous whenever power output must be accurately and safely controlled. The load movers, cylinders, jacks, rotary actuators and hydraulic actuators in these systems can be made to smoothly and accurately start, stop, reverse, hold position or move steadily under heavy and variable loads or torques. Because hydraulic systems are simple, compact, reliable, and low cost compared to other power methods and because they can deliver controlled power anywhere on the machine to which a hose can be routed, they are a pan of almost every type of machine found on a coal mining section. Some of the functions they perform are positioning drill booms, driving drill pots on roof bolters, positioning curter booms, raising, lowering, and swinging conveyors, driving conveyors on continuous miners, raising, lowering, and applying sustained loads to longwall roof supports, and advancing the face conveyor and roof supports in longwall mining operations.

Jan 1, 1982

By A. N. Clay

In recent times, there has been criticism of the minerals industry over the lack of quantifiable boundaries between inferred, indicated, and Measured resources. A recent initiative through the United Nations aims to try to converge the mineral resource classification systems. Since the oil and gas industry uses a probabilistic approach to defining reserve boundaries, it is appropriate to introduce a similar statistical methodology for minerals. The Venmyn Variance Tower has been developed based upon traditional statistics to utilize historical and ongoing information in order to quantify variance of geological and chemical parameters and the boundaries and logic for quantitative mineral resource classification. It is proposed that a less than 50% variance from the mean of all sample parameters is required to achieve the classification threshold to define an inferred Resource whereas between 20-10% is needed for an indicated Resource and less than 10% variance from the mean is needed to declare a Measured Resource. These limits are similar to those used by the oil and gas industry, and it is suggested that these thresholds be adopted as an industry standard to ensure consistent quantitative reporting. While this process is intended to use statistics of an orebody to provide quantifiable and defendable boundaries, it cannot be carried out unless the geology of the mineral deposit is understood and the borehole samples can be categorized into appropriate populations for which the statistics are valid. This means that competent geologists are always required to work with and understand the implications of the Variance Tower results. This paper is intended to form the basis of a series of publications that establish a process to take mineral projects along a quantifiable and logical development path. Hence, no specific field example of the practical application of this process is given here.

Jan 1, 2012

By Alla D. Mah

Titanium forms several compounds with oxygen and also is able to dissolve interstitially about 33 atomic percent of oxygen. Starting with titanium dioxide, reduction becomes increasingly difficult as oxygen is removed; and the final step, be reduction of the titanium-oxygen interstitial solutions, is by far the most difficult. The possibility of reducing titanium oxide, or of purifying titanium containing oxygen, by treatment with certain more volatile metals has been a subject of considerable interest. Theoretical appraisal of the limitations of this possibility, however, has been hampered by lack of adequate information on the thermodynamic properties of the titanium-oxygen solutions. The purpose of the present work was to remedy this difficulty by expanding the thermodynamic knowledge regarding these solutions. The experimental work involved three types of calorimetry and furnished the following information: (1) Heats of formation of 11 titanium-oxygen solutions, in the range of 0 to 10 wt.-percent oxygen, were determined at 298.15° K. As a byproduct, an improved value of the heat of formation of rutile was obtained, which, in turn, led to improved values of the heats of formation of the lower titanium-oxygen compounds. (2) Low-temperature heat-capacity data and entropies at 298.15°K in were determined for 2 representative titanium-oxygen interstitial solutions. (3) High-temperature heat-content data were obtained for 2 titanium-oxygen interstitial solutions to about 1,600° K.

Jan 1, 1957