Search Documents

By Ramana. G. Reddy, Haoxing Yang

The electrodeposition of zinc from zinc oxide using urea and choline chloride mixture in a molar ratio 2:1 is investigated in different experimental variables, namely, the concentration of added [BMIM]HSO4, temperature, and applied cell voltage. The additive, [BMIM]HSO4, was determined to have beneficial effect on the current efficiency, energy consumed in the process and surface morphology of the deposits. The highest current efficiency (92.6%) and lowest energy consumption (2.92kWh/kg) was obtained for solution with 20mg/mL [BMIM]HSO4. The morphology showed the formation of absorbed additive layer on the cathode at higher concentration of additives. Experiments were conducted at different temperatures between 343K and 388K and at various applied cell voltages between 2.7V to 3.6V to determine the best experimental conditions. By varying temperature, highest current efficiency (91.3%) and lowest energy consumption (2.69 kWh/kg) was obtained at 373K. The electrodeposition process is enhanced between the applied voltage 3.0-3.3V by achieving lower energy consumption (2.75~3.06kWh/kg) and higher current efficiency (88.4~89.7%). SEM images showed grain size is significantly increased in higher applied voltages. While at higher temperatures, it seemed to generate particle growth as clusters at the outer deposit layer.

Jan 1, 2014

By Qiang Zhong, Bin Xu, Qian Li, Yong-bin Yang, Tao Jiang, Yan Zhang

The occurrence of different ringing behaviors in oxidized pellet kiln for two kinds of coal (A and B) with similar properties, is difficult to explain based on the relationship between kiln ringing and coal properties. In this paper, the interaction of coal ash with pellet scrap powder was considered by studying the cohering behavior of powders consisting of them. The results showed that the cohering briquette strength of pellet scrap powder increased considerably when mixed with a small amount of coal ash; a maximum could be reached when the mass percent ratio of coal ash was 1.5%; the strength of powder mixed with coal B ash was always higher in same firing system. This obviously illustrated that coal B caused a more serious ringing problem. The relevant mechanism was that the stronger reactivity of coal B ash made cohering briquette have a more perfect crystallization and a more compact structure.

Jan 1, 2015

By S. Frimpong

Cable shovels are used for primary excavation in in-situ and/or pre-fragmented formations in surface mining operations. Poorly fragmented hard rock formations and random occurrence of hard boulders in soft formations cause extreme variability of material diggability, resulting in varying shovel stress loading. The stress loading of a shovel’s front-end assembly could result in fatigue failure. Conventional design process, which uses physical shovel simulation studies, is very costly and time consuming for achieving statistically significant results. In this paper, rigid and flexible multi-body dynamic theories are used to develop component stress loading and deformation models of the cable shovel, and solved in the ADAMS/NASTRAN/FLEX environments. Detailed simulation experiments are carried out to examine the performance, reliability, durability and efficiency of the P&H 4100A under varying in-situ formation conditions. The results show areas of high stress fields with a maximum stress of 313.31 MPa at node 441 within the hoist rope. The reliability of the results is confirmed by comparing existing test data. The study is significant because it provides a solid foundation for further study of failure life analysis of the cable shovel components.

Jan 1, 2007

By Sahin Furkan Sahiner, Onur Golbasi

Effective maintenance planning is vital for coal mining operations, where haul truck fleets directly determine production continuity. This study presents a discrete event simulation (DES) model for evaluating maintenance strategies under multiple failure modes and their interdependencies. The model integrates corrective, periodic preventive, and opportunistic maintenance, dynamically updating equipment lifetimes through probabilistic time-betweenfailure and time-to-repair distributions. Applied to a fivetruck coal haulage fleet over a one-year horizon, results show that periodic preventive maintenance delivers the highest availability (76%) under unconstrained conditions, slightly outperforming corrective-only maintenance (75%). Opportunistic and integrated approaches performed worse (68% and 69%), reflecting redundancy from overlapping interventions. These findings suggest that structured preventive programs provide the most reliable outcomes when costs and resources are not limiting. The DES framework serves as a baseline for future models incorporating cost, spare parts logistics, and workforce availability, supporting robust maintenance planning in coal mining operations.

Feb 22, 2026

By Eliezer Kamon

To finalize the three years granted for the study of miners physiological responses to emergency situations, all the data obtained, were summarized into the following relevant sections; A.. Information on elements of the Man Test required under Subpart 4, Part 2, Title 30 in the Code of Federal Regulation (see Table M-T and Ref. I., Section A). B. Investigation on possible emergency activities, its simulation in the laboratory and the physiologic data obtained on miners performing them This included some studies under cool ambient conditions, expected to prevail in coal mines. C. While in section B the steady state responses have been obtained, time was devoted to establish a unit that will allow data gathering for non-steady state, i.e., transient responses to rapidly changing activities. Section B and C contained elements that were relevant to section A; the Man Test. Therefore some of the information described under section A Man Test, were actually measured during the battery of tests in either section B or in section C.

Jan 1, 1974

By Jaffrey Y. Foley

Placer gold and platinum-group metals (PGM) In the Slate Creek area, northern Chistochina Mining District, are derived from silicified and carbonate-altered, Cretaceous-Tertiary (?) dikes and related mafic and ultramafic rocks. Gold In the placer deposits is also derived from Tertiary conglomerate and altered Jurassic-Cretaceous argilllte. The argilllte and Igneous bedrock sources show a unique Ag-Au-Cu-Hg-PGM association that Is attributed to a combination of magmatic, hydrothermal, and supergene processes. The bedrock and placer deposits contain a variety of gold silver-lead-copper and PGM alloys. The observed geochemical, mineralogic, and alteration features are consistent with current geological models for turbidite-hosted gold deposits. No economic gold or PGM lodes were Identified, but several areas warranting more detailed investigation were Identified. Conventional geochemical sampling and analysis of small sample splits weighing between 10 and 30 grams were shown to be unreliable as a consistent means of identifying gold- and PGM-bearing bedrock. Pan concentration of pulverized rock samples was shown to be a more effective, but still Imperfect means of Identifying gold and PGM source rocks. Geochemical data and mineralogic examination indicate that gold and PGM in potential lode sources are very finely and erratically disseminated, are chemically combined with other elements, and may not be entirely free-milling or amenable to simple gravity concentration.

Jan 1, 1990

During the interval 1929-41, geophysical exploration in Russia made considerable progress, as reflected in publications. The greater part of these publications was available during the preparation of Geophysical Abstracts and Ms been abstracted in them. The rest was not received and remained unaccounted for. A considerable portion of these lading publications are now listed in bibliographic form, in view of their interest to geophysicists. All publications entered in the bibliography are in Russian. 1. GRAVITATIONAL METHODS 1. Abakelia, M. S. The Organization of Gravitational Observatories in Transcaucasia. Problemy Sovetskoi Geologi, Moscow, vol. 6, No. 5, 1936, pp. 452-454.

Jan 1, 1945

By Albert L. Toenges

The Deep River coal field is in Chatham, Lee, and Moore Counties, N. C. The coal-bearing part of the basin is about 35 miles long and 5 to 10 miles wide. Sanford, the county seat of Lee County, is the largest town in the area, with a population of 10,000. Four railroads provide transportation to the area, and four United States highways and improved county roads provide easy access to the field. The Carolina mine at Farmville is the only operating mine in the field. The mine was opened in 1921 by two rock slopes driven from the surface to the Cumnock bed. Mining operations continued intermittently until 1945 and then stopped. In the fall of 1947 the mine was reopened by the newly organized Raleigh Mining Corp.

Jan 1, 1952

The mining and minerals extraction industries have often been demonized by the public as industries that put profits and production before people. It is true that the inherent danger of the work has led to more fatal accidents than anyone associated with the industry would care to remember. But, in stark contrast to what has often been said, the truth of the matter is safety is now the top priority of every miner, from the face of the longwall to the executive boardroom. Without safety, nothing else matters. This message was told and retold by representatives from some of the world?s top mining and petroleum companies from Oct. 11-13 during the inaugural Safety and Reliability in the Mining and Resources Industries Conference in Calgary, Canada. The meeting was hosted jointly by the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) and the Society for Mining, Metallurgy, and Exploration (SME). It was the first of a series of conferences to focus on these important topics. Next year, the conference will be held in Minneapolis, MN from Nov. 13-15.

Jan 1, 2011

By Floyd C. Bossard

In underground mining operations, the over- riding issue has to be protection of worker health and safety. The employees underground, making a living in a dangerous occupation, know these are major issues. These men bargain their lives and health on the presumption that the operating management knows its business, and they, the underground employees, can pursue their occupation with the assurance that management has provided a safe and healthy ambient underground environment. When management assumes the mantle of protection of underground workers, it has to be positive that qualified engineers have designed the project, and that capable operating personnel are in charge and always available. Those persons with these responsibilities must be knowledgeable in the engineering and occupational health aspects of sine ventilation. The ultimate function of a mine ventilation system is to provide a comfortable, healthy and safe ambient environment for the underground workers. The attainment of these objectives has been complicated with the increased application of electrical equipment and diesel-powered mechanized mining equipment underground (discharging toxic diesel emissions); increased production rates with the attendant increased production of airborne dust; and mine development in increasingly hostile mineral formations containing combustible strata gases, radon gas emissions, along with high heat and humidity. In general, the modern mechanization of present mining operations has resulted in a sore complex set of problems for the engineer planning the underground ambient environment.

Jan 1, 1983

The annual reports of the supervising engineer of the seven sections comprising the Mining Division are assembled in the following pages and form the annual report of the division. In planning activities, the aim has been to adapt the work to changing conditions and needs of the mining industries and to avoid becoming bound to any particular type of investigation when others are found to be of more pressing interest.

Jan 1, 1939

By H. D. Bemis

This paper describing the milling practice of the American Metal Co. at its Pecos con¬centrator is one of a series on milling methods and costs being prepared by the United States Bureau of Mines. ACKNOWLEDGMENT The author acknowledges the assistance rendered by Guy Martin, metallurgist, H. E. Brown and J. H. Hastings, chemists, and Thomas J. Fahey, accountant, in gathering and pre¬paring the data presented in this paper.

Jan 1, 1932

By V. E. McKelvey

Any discussion of growth and future requirements has to begin with people--both their number and their needs. Both have been rising ever since any American can remember. Together, the number of people, which has been increasing rather modestly, and their wants and desires for material things, which have been increasing very sharply, seemed to have comprised a growth imperative in mineral consumption in the United States, especially during the last several decades. While the Nation's birthrate is now well below the replacement rate and still falling, the built-in momentum of the post-World War II population boom will continue to be felt well into the 21st century. Even using the modest projection of a 0.8 percent yearly increase, we are still looking at the possibility of 265 million Americans being around by Year 2000.

Jan 1, 1975

By N. A. Eilertsen

Eastern Aroostook County, Maine, contains an enormous tonnage of manganese widely distributed in manganiferous sedimentary beds composed of hematitic shale, hematitic slate, and laminated siliceous carbonate rock. The bedded deposits range in thickness from several feet to over 150 feet. Manganese minerals that occur as silicates and carbonate are so minute that they cannot be concentrated by present methods of ore dressing. From a hydrometallurgical standpoint, the deposits can best be classified by amenability to acid leaching. The deposits of Aroostook County are in three geographical groups (see fig. l), designated as the northern, central, and southern districts. At least 13 deposits are known to occur in the latter district, which covers an Ewes about 8 miles wide and 15 miles long. The Littleton Ridge deposit, on the northern boundary of the southern district, previously examined by geologists from the State and Federal Geological Surveys on the farms of Donald H. Haggerty and David A. Abernethy, was pointed out in reports as being possibly the richest and largest in the southern district. The Bureau of Mines sampled this deposit by surface trenching and diamond drilling from May 1 to September 30, 1951. A total of 23 trenches was bulldozed, aggregating 5,355 linear feet, of which 8 trenches were sampled by cutting 185 channel samples over a linear distance of 1,820 feet.

Jan 1, 1955

By J. Waldman, M. B. Bever, A. K. Jena

The heats of formation at 273°K of 6 silver-rich Ag-Cd solid solutions and the heat of formation at 78°K of one solid solution have been measured by tin solution calorimetry. The heats of formation are analyzed in terms of the quasichemical theory. If the enthalpy diffel-ence between a hypothetical fcc form and the hcp form of cadmium is taken into account, this analysis does not lead to the conclusion put forth in the literature that electronic effects make significant contributions to the heats of formation of silver-rich Ag-Cd solid solutions. The temperature dependence of the heats of formation is appreciable and negative near 78ºK, but decreases gradually to nearly zero abore 400°K. The relative partial enthalpies per grarn -atom of silver at 541°K and cadmium at 532" and 541°K in tin have also been determined. THE composition range of the silver-rich Ag-Cd solid solutions stable at room temperature extends to about 40 at. pct Cd. Heats of formation of these solid solutions at 308" and 723°K have been measured by solution calorimetry.1,2 Heats of formation for an average temperature of 800°K have also been calculated from vapor pressures.2,3 The heats of formation deviate from the values predicted by the quasichemical theory above about 30 at. pct Cd. This deviation has been attributed to electronic effects at the Brillouin zone boundaries.2 The heats of formation of Ag-Cd alloys are essentially the same at 308", 723", and 800°K; consequently the temperature dependence of the heat of formation d?H/dT = ?Cp is vanishingly small, although from the exothermic heats of formation a negative value would have been expected. In the investigation reported here the heats of formation at 273°K of 6 silver-rich Ag-Cd solid solutions and the heat of formation at 78°K of 1 solid solution have been measured by tin solution calorimetry. The results are analyzed in terms of the quasichemical theory and the dependence of the heats of formation on temperature is discussed. The relative partial enthalpies per gram-atom of silver in tin at 541" and cadmium in tin at 532" and 541°K were obtained in the course of this investigation. The values of the temperature dependence of the relative partial enthalpies per gram-atom of silver in tin derived from the data reported by various investigators2,4-9 are contradictory. The literature contains only a value for 517°K of the relative partial enthalpy per gram-atom of solid cadmium in tin.2 EXPERIMENTAL PROCEDURES Samples of Ag-Cd solid solutions were prepared by melting weighed amounts of silver (99.99 pct pure) and cadmium (99.95 pct pure) in graphite crucibles under a flux of molten potassium chloride.10 The solidified ingots were sealed in evacuated Vycor tubes and annealed at 775°K for 10 days. The ingots were swaged and drawn into wires. The wires, sealed in evacuated Pyrex tubes, were held at 725°K for 5 hr and cooled to 365°K at an average rate of 2.5ºK per hr, followed by furnace cooling to room temperature. Chemical analysis of samples taken from different parts of each ingot gave no indication of segregation. Metallographic examination showed the samples to be homogeneous. Samples of the solid solutions or of the component elements were added to tin-rich baths in a calorimeter." At the start of a run the bath consisted of pure tin. Silver was used in the form of wire of 0.01-in. diam as supplied and cadmium in the form of lumps. Gold (99.999 pct pure) was added with the samples in order to reduce the endothermic heat effect of additions of Ag-Cd solid solutions. Samples of only one composition were added in a run and the ratio of the weight of alloy to that of gold was the same in all additions of a given run. In each run several calibrating additions of tin were made from 273°K. The heat contents of tin were calculated from the following equation, which is based on published data:12 (HTºK- H279º) = 6.70 T - 72,300/T + 20 cal/gram-atom; 505°K < T < 650°K The heat effect of each addition was plotted against the average of the sum of the atom fractions of solutes in the solution before and after that addition. The total concentration of solutes at the end of a run was less than 2 at. pct. In this range the heat effect was a linear function of the atom fraction of the solutes. The heat effect at infinite dilution and the composition dependence of the heat effect were obtained from the plots. RESULTS AND DISCUSSION Evaluation of Data. The linear dependence on composition of the heat effects of additions suggests that in the dilute range the enthalpy interaction coefficients other than the first-order coefficients of silver, cadmium, and gold are negligible, as shown in a concurrent publication.13 The heat effects at infinite dilution and the values of the composition dependence of the heat effects are listed in Table I.

Jan 1, 1970

By A. Simkovich, R. W. Lindsay

The possibility of using sodium sulfide slags to remove copper from ferrous alloys has been investigated by Jordan1 and by Langenberg.2, 3 In these studies, such slags were determined to be capable of removing copper and sulfur from the melt. The present work represents additional effort to clarify the effects of temperature on copper removal. The experiments were performed in a 17-lb induction furnace. Graphite crucibles contained the melts and kept the baths saturated with carbon. Temperatures were measured with a calibrated optical pyrometer and were controlled by manipulation of power input to the furnace. Estimated accuracy of temperatures in this investigation is ± 10°C (18°F) for measurements prior to slag additions, and + 20°C (36°F) after slag formation. The procedure consisted of melting 800 g of electrolytic iron. During this step, powdered graphite covered the exposed iron surface. After a predetermined temperature was reached, copper shot was added. A sample of the molten alloy for chemical analysis was then aspirated into a silica sheath. Next, a slag-forming mixture of sodium sulfite and graphite was added instantaneously to the melt. The sodium sulfite amounted to one-tenth the charge weight of iron; sufficient graphite was added to combine with oxygen in the sodium sulfite, assuming formation of carbon monoxide and reduction of the sulfite to sulfide. Subsequent to the slag addition, the molten alloy was sampled periodically, with the exception of heat A in which no intervening samples were taken between the slag addition and the end of the run. The iron was poured into a graphite mold, and the ingots sectioned and drilled for samples. Results of selected heats are presented in Table I. Analyses of samples drawn from the iron prior to slag addition are listed under zero time. Two samples from heat D were reported with copper contents greater than the initial concentration in the bath. Owing to the gradual but complete disappearance of slag during this heat, it is believed copper momentarily became more concentrated in the upper portion of the bath while reverting from the slag. This is the region from which samples were drawn. It should be noted that analysis of the ingot was equal to the copper content at the time of slag addition. The terminal temperatures of heats D and E, and the initial sulfur content of heat A are also to be noted. Because of the large temperature drop which occurred when slag was formed in heat D, power input to the furnace was increased in heat E after the slag addition, causing a higher terminal temperature. In heat A, the initial sulfur concentration was relatively high as compared to heats B through E owing to contamination by some slag remaining in the crucible from a previous heat. It is evident from Table I that copper was removed at the onset of slag formation. Roughly 30 pct of the copper was taken into the slag, with the exception of heat D, which had approximately 50 pct removed. For a comparatively short time of slag-metal contact, it appears that no gain is to be made in copper removal through use of high or low temperatures. If the slag initially formed remains in contact with the iron for an extended period, temperature has a marked effect upon copper removal, as can be seen by studying results for the two extremes in temperature. At about 1425°C, the copper level remained relatively constant after the initial removal by the slag. However, in the region of 1670°C, a definite reversion of copper occurred. Reversion was incomplete in heat D, and complete in heat E. The final temperatures of heats D and E differed by about 75°C. This temperature difference is thought to be the reason for only partial copper reversion in heat D. It is believed the effects of temperature noted above are related to the evolution of a white fume, which appeared in every run except heat A. (In the case of heat A, the fume was practically indiscernible.) After each slag addition, a yellow flame formed for about 5 sec. When the flame subsided, a white fume appeared. Upon contact with surrounding cooler surfaces, this fume deposited as a white solid. In the experiments made at 1425°C, evolution of fume continued unchanged to the end of the runs. However, heats D and E exhibited a different behavior. A very noticeable decrease in fume evolution from heat D was observed. Furthermore, this heat had much less slag remaining than did runs A through C when the experiments were terminated. No slag remained at the end of heat E; evolution of fume from this heat ceased prior to pouring. Spec-trographic analysis of the white deposit indicated sodium to be the major metallic element, with the maximum concentration of iron and copper as 0.1 and 0.01 pct, respectively. It is supposed the white fume observed in these experiments is principally sodium oxide (Na2O), formed by oxidation of sodium in the slag and subsequent sublimation. (Sodium oxide is a white to gray substance in the solid state; at 1275oC, it sublimes.4) According to this mechanism, elevated temperatures would accelerate removal of sodium from the slag, sulfur pickup by the

Jan 1, 1961

By W. H. Strickland, R. H. King

Ultrasonic ranging sensors are inexpensive, have no moving parts, have no lenses to clean, are normally small and unobtrusive, and can measure distances through moderate amounts of dust, smoke, and humidity, so they are well suited to underground mines. In the work reported here, conducted by the U.S. Bureau of Mines, researchers tested ultrasonic ranging sensors for their abiity to define rib line features for computer-aided navigation of underground mine mobile equipment. The investigation began with laboratory tests of field of view, angle of incidence, intersensor variation, and ranging accuracy of the individual rangers in a ring array produced by Denning Robotics of Wilmington, MA. The results showed that the sensors have good accuracy and low variability. Additional experiments at AMAX&apos;s Henderson Mine showed the sensors could accurately and reliably measure the distance to mine features, including convex and concave corners and rib intersections. The results showed that when used properly, the ranger data are accurate enough for reliable mine vehicle navigation When used incorrectly, ultrasonic rangers do not provide the anticipated data. Therefore, this report explains the principles of ultrasonic range measurement, describes the ranger&apos;s strengths and weaknesses, and explains proper ranger use and data analysis.

Jan 1, 1993

By Tapio Leskinen

"l. IntroductionA reliable sampling system is the basis for an on-stream analyzer. This was realized in Outokumpu company when the development work of the Courier 300 On-Stream X-ray analysis system was started. Because Outokumpu Oy is a mining and mineral processing company, its engineers have been able to thoroughly test sampler prototypes in actual operating situations. The sampler development has been going for several years in close co-operation between company's concentrators, the Institute of Physics and the Instrument Division of Outokumpu Oy. The most active part of the work was done between 1969- 1972. Besides the reliable operation of a sampler special attention was paid to the representatively of the samples taken by the samplers. 2. The Courier 300 Sampling SystemThe sampling system comprises up to fourteen sampling circuits in one Courier analysis system. Each circuit consists of the following components:1. Primary sampler 2. Secondary sampler 3. Cleaner screen 4. Feeding tank5. Sample cell6. Timer-controlled sampler7. Pumps, sumps and pipesSecondary samplers, cleaner screen and feeding tanks are included in the secondary sct1npling system. The sample cells are located in the spectrometer cabinet of the analyzer."

Jan 1, 1976

By W. R. Hardwick

This paper describes mining methods and practices of the Chino Mines Division, Kennecott Copper Corp., Grant County, N. Mex. It is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. A similar program was conducted from 1928 to 1939, which helped to improve the efficiency of mining operations. The primary purpose of the program is to promote development and conservation of our mineral resources by disseminating technologic information on methods, practices, and related features in mining mineral deposits. It is expected that the program will: (1) Promote efficiency in operating mines; (2) assist operators and engineers in evaluating and developing new mineral deposits; (3) provide data for engineering curriculums in mining schools; and (4) furnish performance and cost data for revising engineering handbooks and for inclusion in engineering textbooks.

Jan 1, 1958

By Allan J. Clark

This paper, describing the milling practice of the Homestake Mining Co., is one of a series being prepared by the Bureau of Mines. The author acknowledges the assistance of T. G. Chapman, one of the consulting engineers of the Bureau of Mines, in arranging this paper for publication.

Jan 1, 1931