Search Documents

By Ferdinand Roehlich

An evaluation of the use of manually activated, installed,. dry chemical fire protection systems on underground metal and nonmetal mine vehicles is described. In addition, an assessment of the possible health risks posed by the dry chemical extinguishing agents used in such systems is provided. Work involved installation of fire protection hardware on an operating piece of underground metal/nonmetal mine equipment and, via actual fire tests, a determination of the effectiveness of the hardware in extinguishing on-vehicle fires. Two fire protection systems were installed on a Caterpillar 988 front-end loader in St. Joe Mineral's Fletcher mine, near Viburnum, Mo. Both a fully pressurized Safety First CM-20 and a nonpressurized cartridge actuated Ansul A-101 were installed for comparative purposes. Both systems operated satisfactorily during an 8-month endurance trial period which preceded the actual fire tests. Each system was able to extinguish an 18" x 4" class B test fire placed in the engine area of the machine. The health hazards analysis of dry chemical powder consisted of a detailed search of published literature relating to these multipurpose agents. This data was verified via a controlled laboratory analysis of two monoammonium phosphate based powders (Safety First Unikem and Ansul Forey) and an analysis of air samples collected at various locations on the test vehicle during the fire tests. Although the powder was found to be nontoxic, two potentially dangerous thermal decomposition products were identified--ammonia and phosphoric acid. However, later analysis indicated that an operator would not be exposed to dangerous concentrations of either compound if he were to remain outside of the powder cloud. A "Selection and Use Manual for Manually Activated, Fixed Fire Suppression Systems on Underground Metal and Nonmetal Mining Equipment" was prepared both as an, appendix to the report and for distribution under separate cover.

Jan 1, 1977

By F. Calizaya

A booster fan is an underground fan installed in series with a main surface fan and used to boost the air pressure of the ventilation air passing through it. To accomplish this objective, the fan is installed in a permanent stopping and equipped with airlock doors, a monitoring system, and interlocking devices between main and booster fan controls. The stopping and doors are used to prevent flow recirculation, and the monitors to ensure safe operation of the fan. A booster fan, properly sized and sited, can be used to create safe work conditions and allow the extraction of minerals from areas that would otherwise be uneconomic to mine. In deep and large mines with heavy emissions of air contaminants, the required quantities of air can only be supplied by using high pressure fans. These fans will inevitably induce significant losses of fresh airflow through the stoppings and doors. For well defined ventilation circuits, booster fans can be used to decrease the main fan pressures and reduce the leakage flows. However, this will require a good understanding of the correct ventilation practice, from planning to operation and maintenance of booster fans. The objective of this study is to investigate the conditions under which booster fans can be used safely and efficiently in underground coal mines. Specifically, the study is directed at (1) collecting reliable information on airway resistances and flow requirements from two large U.S coal mines, (2) collecting fan performance data from one or more existing coal mine where booster fans are used regularly, (3) monitoring the performance of booster fans in a laboratory model and an experimental mine, (4) developing a booster fan selection method to assist the ventilation engineer at the planning stage, and (5) training six M.S. or Ph.D. graduate students in advanced mine ventilation.

Jan 1, 2010

This information circular describes research the Bureau of fines has conducted to improve technology for recovering precious metals from low-grade resources. Many of the reported findings are recent, and some of the work described is ongoing. Topics discussed include cyanidation of carbonaceous gold ores to enhance gold recovery, a new method for precipitating mercury during cyanide leaching of gold ores, a staged heap leaching process to generate suitable solutions for direct electrowinning of gold, the use of anion-exchange resins to recover gold from cyanide solutions, and precious metals recovery from electronic scrap.

Jan 1, 1986

By H. S. Auvil

[Coals of low-volatile rank cannot be coked without admixing large proportions of high-volatile coal in the usual type of byproduct-coke oven, because they expand excessively and exert side thrust, which ruins the oven walls. Some medium-volatile coals also give trouble. Since high-rank coals produce a strong, blocky coke, it is desirable to have the rank as high as practicable, particularly in the manufacture of foundry coke. Accordingly, it has become the practice to mix or blend high-volatile shrinking, coals with as much low-volatile coal as possible and still have a mixture that will not deform the walls or cause difficulty in pushing the coke. Occasionally, the safe limit of low-volatile coal has been exceeded and ovens have been damaged. It is desirable, therefore, to rave a reliable method of determining the expanding tendencies of mixtures before they are charged into the ovens. Furthermore, coal charges somewhat in its properties as mining progresses, and therefore, mixtures found to be safe at one time may cease to be so subsequently, particularly if nearly the maximum allowable percentage of low-volatile coal is being used.]

Jan 1, 1938

By G. W. Birge

Twenty-eight samples, representing the Pittsburgh, Lower Kittanning, Stockton-Lewiston, Coalburg, Winifrede, Cedar Grove, Peerless, No. 2 Gas, Powellton, and Eagle beds, were carbonized by the Bureau of Mines--American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Expanding characteristics of 22 of the samples were determined in the Bureau of Mines sole-heated oven. The Kanawha County coals tested were high-volatile A bituminous in rank, with dry, mineral-matter- free fixed- carbon contents ranging from 53.9 to 66.3 percent. With few exceptions, they were chemically satisfactory for metallurgical use, and most of the coke-strength indexes were within the industrially accepted range for high-volatile blending coals.

Jan 1, 1963

By Vishwajeet Ahuja, Benoit Jones

"INTRODUCTION Shotcrete lining forms an integral part of conventional tunneling and is widely applied for underground excavations. Early strength gain of the shotcrete is a crucial aspect for ground support and safety of operatives. Strength requirements are dependent on various factors such as lining thickness, ground type, excavation size and tunnel depth. The early strength gain is typically monitored using destructive tests, such as needle penetration, stud driving or coring samples for uniaxial compressive strength testing in the laboratory. Being destructive, these tests cannot be directly performed onto the lining without causing damage that must be repaired, which is a particular problem for permanent linings. For this reason and to avoid the need for operatives to work near to exposed ground and/or fresh shotcrete, these destructive tests are often performed on panels, which are sprayed at the same time as the tunnel lining. All current testing methods are also very local, testing only a small part of the lining or a panel, which may not be representative because the temperature history could be significantly different. Therefore, these tests do not provide an accurate or complete picture of the lining strength gain. New testing methods that are non-destructive and can scan the whole lining remotely would be extremely desirable. This paper describes a new method, using thermal imaging techniques, that achieves these aims. It also discusses the real-time on-site application of the method, providing insight into the experience gained and conclusions derived. Shotcrete Shotcrete used for tunnel linings requires immediate strength development. The strength development is a direct result of the hydration reaction of cementitious materials present in it. A progressive sequence of the hydration reaction changes it from a solid suspension (typically referred to as fresh concrete) to a solid skeleton with a porous network and thereafter, into a solid with predominantly discontinuous pores (Byfors 1980). In the case of shotcrete, early strength is needed to support the self-weight and then continuing early age strength gain is required to begin to support ground loads. These strength requirements, along with other workability needs, are met by careful concrete mix design, the use of admixtures, such as accelerator and superplasticizer (BS EN 934-5 2007), and supplementary cementitious materials, such as silica fume."

Jan 1, 2016

By Rainer Schmid-Fetzer

"Isothermal solidification can be used to form strong bonds at low temperature which remain solid at much higher temperatures. The exploitation of this principally known technique for new high temperature processing steps and applications in electronic assemblies is the aim of this study. Three basically different variants of this bonding process are given. A comprehensive metallurgical screening is performed and the feasibility of binary material systems is given on a quantitative scale. Very attractive systems are spotted that have never been studied before. Detailed examples for the realization of bonding with complex ternary and multilayer systems are given. A highly innovative example is the chip stack or wafer to wafer bonding of unmetallized Si or SiC at 250°C. The proposed bond remains stable above the melting point of Si and enables entirely new semiconductor manufacturing steps. An improved die bonding process was proposed and verified experimentally.1. IntroductionIsothermal solidification can be applied to form strong bonds at relatively low temperature which remain solid at higher temperatures. The general principle of this type of joining processes is illustrated in Fig. 1. An interlayer of a low melting component, Lo, is provided as a foil or a thin film coating between the high melting joint components, Hi. The assembly is heated under moderate pressure to the bonding temperature, T 8 , and a liquid filler forms, either because the melting point of Lo is exceeded or due to a eutectic reaction between Lo and Hi. This molten filler initiates a rapid interdiffusion or reaction diffusion between Lo and Hi and the subsequent approach to an equilibrium state results in isothermal solidification. The solid phases formed at T 8 in the joint region exhibit a remelt temperature above T8 •"

Jan 1, 1996

By Michael Windhager

UltimaTM rolls have been designed for intermediate and finishing stands of rod and bar and small and medium section mills. The rolls and rings are spun cast, with a highly alloyed working layer and a tough nodular iron core. Microstructure and hardness level can be adjusted over a wide range, which allows us to adapt the rolls to differing rolling conditions. After introducing the UltimaTM concept, this paper will describe the results of UltimaTM rolls achieved in various mill applications, like finish rolling of rebar, and slitting. Special emphasis is given to performance gains when using UltimaTM rolls, compared to standard rolls. This paper also examines the impact of UltimaTM rolls on mill and roll shop productivity.

Jul 30, 2018

By M. W. Davies, P. N. Smith

The activity of MnO has been measured in the system CaF2-MnO at 1773 and 1873 K and in the system CaF2-CaO-MnO at 1773 K by the method of equilibration with platinum. Large positive deviations from ideal solution laws have been found, but these became less as the lime content rose. The loss of a volatile component made activity measurements impossible in the CaF2-AI203-MnO system, but the boundaries of a two-liquid region have been measured at 1773 K.

Dec 1, 1971

By M. R. HULL

FOLLOWING the discovery of a body of ore that appears to have commercial possibilities there is a period of development work to determine its extent and grade and the most economical method of mining it. Laboratory tests are made in an effort to determine the most practicable and economical treatment for the extraction of the valuable constituents of the ore and these tests are carried farther and checked in a pilot or test mill. The rate at which the ore is to be mined and the daily capacity of the plants that are to treat it will depend on a number of important factors such as: The size of the orebody; the capital available for building the plants; the market or demand for the final product; the supply of skilled and common labor available for the construction, operation and maintenance of the plants; the quantity and quality of available water, and the amount and cost of power that can be purchased or that can be economically developed. Having decided on the treatment that is to be given to the ore and after full consideration of the above factors the management decides to erect a reduction plant of a given capacity.

Jan 1, 1926

By R. L. Virta

Four companies mined ball call in four states in 2009, H.C. Spinks Clay Co. Inc. (owned by Lhoist Group), Kentucky-Tennessee Clay Co. (owned by Imerys Group), Old Hickory Clay Co. and Unimin Corp. Production, on the basis of preliminary data, was 820 kt (904,000 st) with an estimated value of $39.4 million. That was a 15-percent decrease in tonnage from 967 Mt (1.1 mil-lion st) with a value of $44.3 million that was produced in 2008. Tennessee was the top producing state with 59 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 71 percent of production was airfloat, 18 perc

Jun 1, 2010

By L. R. McCullough

To compete in Today's Market, Mine Managers have two, often conflicting tasks. They are to improve productivity, allowing the mines to compete in our world markets and to improve the environment in which our miners must work. To Maintain and improve the environment to ever increasing acceptable levels requires monitoring. In years passed this required considerable labor, which was provided by the Ventilation Department. They continuously took manual samples using hand-held instruments, sampling gas level such as CO for fire and methane for explosive risks. In addition they took continuous air velocity readings with hand-held instruments which allow them to calculate the ventilation air movement in each area of the Mine. This manual gathering of information was not only expensive and slow but marginal at best. It was marginal because the gas sampling was sporadic rather than continuous, as sample reading taken in one part of the mine would likely not be repeated for another 8 hours. If problems did occur, they likely went unobserved until they reached crisis proportion.

Jan 1, 1990

By T. Ritzel

Predictive maintenance technologies including vibration analysis, tribology, infrared thermography, ultrasonic detection, and electrical measurements have been applied to large electric mining shovels at Cyprus Sierrita. The predictive program was initiated by Cyprus Sierrita and P&H Mining Equipment at the Cyprus Sierrita Mine in Tucson, Arizona during August of 1996 on the P&H model 2300 and 4100 electric shovels. The utilization of these technologies has shown the potential for improving electric mining shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition based planning of component replacement. Maintenance costs are minimized by focusing resources through condition based prioritization.

Jan 1, 1997

1. Domestic Production and Use: In 1975.12 companies operated 31 primary aluminum reduction plants, with 3 firms accounting for 67% of production capacity. Washington, Oregon, and Montana accounted for 37% of the total production; Gulf Coast States 21%, Northern States 29%, and other Southern States 13%. Output of primary metal in 1975 was valued at $3.0 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Of aluminum consuming industries in 1975, building accounted for about 21%; transportation 19%; electrical 14%; packaging 18%; and consumer durables, 9%.

Jan 1, 1976

By Green A. D M

The establishment of the Imperial Smelting Furnace at Sulphide Coporation Pty. Limited for the smelting of zinc and lead made it necessary to design and install sintering capacity to produce approximately 500 t.p.d. of zinc-lead sinter. The updraught sintering process installed is a recent development and the plant was designed with adequate flexibility and equipment to enable operating staff to investigate the process and achieve maximum production under optimum operating conditions.Sulphur dioxide gases from the sinter machine are passed to a contact acid plant for the manufacture of sulphuric acid.

Jan 1, 1964

By R. M. Sweetin

Detailed descriptions by operating area of the Kidd copper smelter are presented, together with accounts of complement staffing, training, and preparation activities for smelter start-up in June 1981. Concentrate tonnages smelted in the first twelve months of operation were constrained by the capacity of the furnace off-gas system. However, modifications designed and introduced over that period, plus sustained efforts by operations and maintenance personnel have resulted in stepwise improvements in smelter performance.. Consistent operation at design feed rates has been well demonstrated over the third and fourth smelter campaigns and efforts continue on further improving the continuous smelter on-line times and increasing campaign life. In November 1982., following a seventeen month preproduction period, the Kidd smelter attained full operating status.

Jan 1, 1983

By W. R. ARGYLE, R. A. SHERMAN, Henry Kreisinger, John Blizard, B. J. CROSS, A. R. Mumford

On entering the World War the United States was confronted with the necessity of building in a short time a large number of ships of tonnage adequate to transport troops and war materials to Europe and to carry food supplies to the allied countries, whose merchant fleets had suffered greatly by submarine warfare. The necessity of building ships quickly led to the formation of the United States Shipping Board, which was charged with the duty of developing an efficient organization for the purpose. Such an organization was developed under the name of the Emergency Fleet Corporation; it was under the control of the Government, but could conduct its business in the most direct way, like a private corporation. In order to build the largest- number of ships possible without drawing too heavily on the steel industry, which was already taxed heavily by the production of munitions, it was decided to build wooden as well as steel ships. These ships were built from a few standard designs to enable a large number of duplicate parts to be fabricated in inland shops and transported by railroad to the shipyards on the seacoast, where they were assembled into ships. In other words, the plan was to manufacture the ships rather than to build them. The shops on the seacoast were reserved to make those parts of the ships' equipment that could not readily be transported. The inland shops made the parts that could be transported to the seacoast by railroad. Among the more important parts of the ships' equipment to be standardized were the boilers. As the Scotch marine boiler in large units is bulky and can not be transported by railroad, and as, for the same capacity,much more steelis needed in its construction than for water-tube boilers, a few simple designs of water-tube boilers were developed that inland shops having ordinary equipment could make in large quantities.

Jan 1, 1924

By Larry M. Southwick

Steel mill electric arc furnace dust is a RCRA listed hazardous waste and its treatment and/or disposal are regulated by a complex set of rules. These regulations were originally established to encourage recovery and recycling of valuable components. For EAF dust, the more valuable constituents include zinc, lead, cadmium and iron. In fact, current trends are in the opposite direction, as the regulations have complicated the ability to commercialize new treatment technologies and created substantial roadblocks and liabilities for processors. As a result, almost half of the EAF dust generated in 1997 will be landfilled. The problems are compounded by difficult processing requirements, less than sterling examples of technology development and mechanical and operating problems. This paper explores some options to simplify the processing requirements and thereby easing difficulties in commercializing new technologies and expediting the recycling of recovered metals. Dust processing usually includes a simple step followed by two complicated steps. The simple step is fuming of heavy metals away from iron and other residues. The complex steps are (1) separating and purifying the heavy metals and (2) upgrading the iron residue. The first complex step can be simplified by producing an intermediate product that is amenable to processing by zinc refiners. This route benefits from the currently underutilized (by dust processors) resource offered by refiners, who have experience in and existing processes for separation and purification of zinc-based heavy metals. Various processes and their associated product options are reviewed and compared. Future directions for dust processing developments are suggested.

Jan 1, 1998

By Georgi N. Shoushoulov, Ventsislav D. Bozhilov

The mining conditions in the Meden Rid mine at levels below 1000 m from the Earth's surface are specific and rather severe. The rock temperature is about 40-45°C. The air humidity in the workings is approx. 80-90%. There is a limited capacity for additional fresh air supply. The air supply and distribution systems in the mine are very complicated. The airflow recirculation is due to the existing arrangement of the main fans. Certain accidental phenomena are difficult to predict. All these conditions create possibilities for heat and mass exchange between the rock and the air current thus hampering the control of the ventilation and air-conditioning in the mine workings. The changes in the temperature and humidity in certain characteristic places of the development and extraction workings are predicted. The refrigeration output required and the arrangement of the air coolers are also determined. A new ventilation and air- conditioning scherne has been developed. The new ventilation- cooling designs for levels between 1000-1200 m beneath the Earth's surface are based on the use of portable refrigerating machines having low water flowrate as well as heat-insulating and waterproof materials and methods for preliminary cooling of the orebody within the mining block.

Jan 1, 1997

By C. van Buuren, R. F. Sandenbergh, P. J. Pieterse

Gold extraction from double refractory ores using conventional cyanidation has proved challenging due to the presence of carbon within the ore. Carbon particles may adsorb leached gold resulting in gold losses to tailings, i.e. preg-robbing the gold. Some of the preg-robbed gold may be recovered by the application of the HiTeCC process on CIL tailings. The process developed by Metso Outotec involves caustic conditioning of the tailings followed by high temperature desorption and simultaneous adsorption onto virgin activated carbon of the aurodicyanide. The aim of this paper was to develop a model for the HiTeCC process which could be used to support design and optimisation of the process, based on the adsorption characteristics of the preg-robbing and activated carbons. It was found that accurate experimental isotherms can be used to predict the behaviour of preg-robbing adsorbents. Comparing the sorption isotherms for preg-robbing ores and activated carbon indicated similar dependencies on temperature and ionic composition. Applying boundary layer diffusion models coupled with experimentally determined isotherms for preg-robbing ore and activated carbon, the HiTeCC process was successfully simulated at experimental and plant scale. Gold recovery of the HiTeCC process is most sensitive to the temperature of desorption and gold loading of the activated carbon, with increased temperature improving recovery. The gold loading of the activated carbon in the process should always be maintained lower than that of the normalised pregrobbing carbon gold loading to ensure favourable conditions for adsorption onto the activated carbon. Caustic conditioning stabilises adsorption and is therefore not necessary during the desorption stages of the process, but potentially improves recovery during adsorption. Keywords: Preg-robbing, refractory gold ores, HiTeCC, aurodicyanide

Jan 1, 2020