Search Documents

By Yiming Sun, David Tsztoo, Rick Nolting, Adam M. Wirthlin, Rebecca Fusee

"Excavation and initial support of the New Irvington Tunnel presented significant challenges, including rapidly changing ground conditions, heavy ground loads, and squeezing. Such behaviors were anticipated from historic tunneling records of the adjacent Existing Irvington Tunnel, and extensive site investigation, but clearer understanding of their actual extent and causes has resulted from convergence measurements, observations of ground behavior, initial support monitoring and detailed geologic mapping. Time-dependent movements, documented hours to months after excavation in clay-rich rock and in moderately to intensely fractured rock, identified squeezing areas, allowed classification by currently-used predictive methods and added to the list of lessons learned in tunneling such ground. INTRODUCTION In March 2003 the San Francisco Public Utilities Commission (SFPUC) authorized funding for the $4.6 billion Water System Improvement Program (WSIP) to repair, replace, and seismically upgrade its water system. The program consists of 35 local projects located within San Francisco and 48 regional projects located in several counties from the Sierra foothills to the San Francisco Bay Area. The New Irvington Tunnel (NIT), a key component of the WSIP, is located east of Fremont in Alameda County, on the east side of San Francisco Bay. The NIT is a new 18,660 foot (5,689 m), redundant tunnel, 190 to 670 feet (58–204 m) offset from, and subparallel to the Existing Irvington Tunnel (EIT). Built between 1928 and 1932, the EIT was constructed with an unreinforced cast-in-place concrete lining and is vulnerable to damage in the event of a major earthquake along the two closest active faults. The Hayward Fault is located less than a mile west of the tunnel, and the Calaveras Fault is located half a mile east of the tunnel. Although the alignment does not intersect these faults, the shaking and sympathetic displacement along secondary faults that cross the tunnel alignment are potential hazards. The NIT provides a seismically reliable water transmission facility capable of withstanding earthquake damage and maintaining continuous water service after a major earthquake. The NIT also adds system redundancy and provides for operation flexibility of running water through both tunnels, or through one tunnel while the other is out of service for inspections and maintenance."

Jan 1, 2016

Real economic growth for 1988 may fall short of the 3.3% projected by the Department of Commerce in August 1988 because the summer drought and intense heat in many areas curtailed output more severely than expected. The economy grew at an average annual rate of 3.0% for the first three quarters of the year, slowing in the second and third quarters. Export growth, which occurred even as the dollar edged up compared with other industrial country currencies, was an important factor in the expansion. Notable gains were posted in sales of machinery, computers, aircraft, chemicals, and telecommunications equipment. Imports increased, but not as much as exports, and the U.S. trade position was still much improved from that of 1987. Personal consumption expenditures grew slightly faster than the economy as a whole. Purchases of consumer durables showed notable strength in the first half of 1988, but slowed down in the third quarter. Despite the moderate rise in interest rates, business spending for new plant and equipment also rose and contributed to 1988 gross national product (GNP) growth. Both new business investment and export demand spurred orders for U.S.-made machine tools. Orders for machine tools for the first 8 months of 1988 were almost triple those in the corresponding period in 1987.

Jan 1, 1989

These proceedings consist of an introduction, nine descriptive papers, and a summary. The first paper is an overview of the respirable dust research program, the second paper describes the Mining Enforcement and Safety Administration's proposed changes in the respirable dust enforcement program, and the third paper describes respirable dust measurement. The remaining papers, by Bureau and contractor personnel, describes methods of reducing the amount of respirable dust to which coal miners are exposed. Of the six methods of reducing exposure to respirable dust described, two are methods of preventing or reducing the amount of respirable dust raised during mining operations, two are methods of collecting or removing dust after it has been released into the mine atmosphere, 2nd two describe methods that are combinations of prevention and collecting .

Jan 1, 1977

By D. Harrington

United States newspapers of 25 or 30 Years ago ran headlines every few weeks telling of some mine disaster. Each disaster was a first-page attraction for a day or so then was forgotten until the next sensational event, frequently another mine disaster, a few weeks later. Interspersed with the large mine disasters were the so-called ?snipping? mine accidents that caused the death of one or two mine workers. The summation of mine fatalities of all types usually exceeded 3,000 a year, and nonfatal accidents to workers in mines of the country approximated 250,000 annually. From 1906 to 1910, inclusive, there were 84 major explosion disasters (about 17 per year) in. United States coal mines. The resulting fatalities totaled 2,388 for the 5-Year period. These frightful catastrophes helped the number of fatalities in coal mines of the country to reach the enormous total of 13,288 for the 5 years, or an average of 2,658 per year.

Jan 1, 1940

By Hardwick F. W., O'Shea L. T.

The survey covers: coal-mine lighting prior to the invention of the safety-lamp, including candles, the flint-and-steel Spedding mill, and mirrors; the growth in knowledge of firedamp; the Society in Sunderland for Preventing Accidents in Coal Mines; Dr. Clanny's blast lamps and steam lamps; George Stephenson's tube-and-slider lamp, triple-tube lamp, punched-plate lamp and gauze Stephenson lamp; Sir Humphrey Davy's lamps; the controversy over invention priority, and other early forms of safety-lamp; 1816-1835 developments including the lamps of Upton and Roberts, M.Mueseler, John Martin, Dr. Clanny (new 4th lamp), M. Agre, John Newman, Gossart and Roberts, Francis Ellis, John Dillon and Mr. Wood (refrigerating lamp); 1836-1843 developments, notably of Mueseler lamps; 1844-1866, including lamps of the Davy, Clanny, Boty, Eloin and other types; 1867-1879, including the Gray lamp; 1880-1887, including the Marsaut lamp; and 1888-1913. Detailed reference is made to the findings of various relevant Royal Commissions and appendices include a list of the safety-lamps described in an appendix to the 1886 report and a publications list. The paper was prepared for the International congress of mining, metallurgy, applied mechanics and economic geology to have been held in London in July 1915. Discussion (p.718-724) includes a brief comment by Blackett W.C. and a longer contribution by Ashworth J., with the authors' response

Dec 1, 1916

By G Pattenden, R Hargreaves, P Pettit

"Even with the cyclic nature of mining, when it comes down to it, the bottom line is that whatever direction the commodity market is going there is always a desire to improve the economics of an operation in order to deliver a greater return to investors. Adapting to market pressures by introduction of an operational process change can often have a downstream impact. What may be less obvious is that reconciliation can play an important part in measuring the effectiveness of many operational changes. Through the adoption of best practice reconciliation and related comparisons, it is possible to measure the impact of changes across the mine value chain and identify variability that may have been introduced. Using analytical business improvement tools, examining and monitoring planned changes can be crucial in understanding whether the introduced changes have been effective and whether they have provided the expected result. Using several case studies, the authors will highlight the benefits provided by modern business intelligence tools, which can provide data validation and accurately report data trends related to both planned and unplanned change events.Citation:Hargreaves, R, Pattenden, G and Pettit, P, 2016. Measuring the Effectiveness of Change through Best Practice Reconciliation, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 71–83 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By O. H. Metzger

This is the second of two papers dealing with the construction and use of aerial tramways in the metal-mining industry. The first paper3/described aerial tramways in a general way and discussed the engineering principles used in tramway design. The purpose of this paper is to give a more detailed description of equipment and material rind to discuss construction and operating costs. ACKNOWLEDGMENTS The paper is based largely on data from actual operations. Metal-mine operators from many parts of the United States, Canada, Alaska, and Mexico contributed liberally.

Jan 1, 1940

By R. Hendrickson

In the 1940's a top blown water-cooled oxygen lance was developed to inject oxygen into liquid iron. This process, the LD or BOF process technique, today is used in 65% of the world's steel production, and represents the largest oxygen market for temperature enhancement in steel and non-ferrous smelting applications. There are three major approaches to the use of oxygen in metallurgical processes: (1) general enrichment of the air supplied to burners or tuyeres, (2) under-flame enrichment or injection, and (3) the use of an auxiliary oxy-fuel burner as a heat source. With each of these techniques there are technical and economic trade-offs.

Jan 1, 1990

By A. W. Gauger

DESPITE many handicaps and in the face of many discouragements anthracite and bituminous coal producers continue to supply the needs of the nation now vastly multiplied by the demands of the greatest war of all time, total output being about 620,000,000 tons of bituminous and 64,445,000 of anthracite. The progress made by this industry during the national emergency reflects more credit on all connected therewith than will ever be given. Not only has the industry been called upon to produce more coal than ever before but it has also sent representatives to England to study and advise on methods for increasing production there, and has co-operated with other Allied Nations by welcoming engineers sent to this country to study American practice. One noteworthy development has been the growth of strip mining in the

Jan 1, 1945

By Charles E. McCarthy

Part 1 of this report is concerned with the electric-furnace production of calcium aluminate and iron alloy from a variety of siliceous ferruginous ores of aluminum. The furnacing research was directed, first, to determine the extent of the field in the CaO-Al2O3-SiO2 system, in which calcium aluminates with the optimum leaching characteristics are obtained; second, to produce suitable quantities of these aluminate mixtures for pilot-plant leaching tests; third, to investigate the physical chemistry of the reduction reactions during furnacing; and, fourth, to study the economics of the process. The third and fourth steps were not completed. Part 2 comprises another phase of the work and will appear as a second Report of Investigations. It deals with the extraction of metallurgical-grade alumina from the calcium aluminate slag produced in the electric furnace and includes the following steps: leaching, desilicating, precipitating, dewatering, filtering, and washing of the aluminum hydrate. No claim is made that the data are complete, nor has the chronological order of obtaining data been followed. Rather, it is emphasized that additional work is necessary if the full possibilities of the process are to be evaluated. and made available.

Jan 1, 1949

By Michael Jatczak, Joseph A. Sopko

Ground Freezing was used for excavation support and groundwater control of a 12.8m (42-foot) diameter, 61m (200-foot) deep drop shaft for the South Bay Ocean Outfall Tunnel in San Diego, California. Approximately half way through the excavation, excessive groundwater inflows from the base of the shaft resulted in suspension of excavation and evaluation of the frozen earth wall. This paper discusses the forensic methods used to identify the zone where groundwater intrusion occurred and the methods associated with evaluating zones of high groundwater velocity. The use of remedial grouting and localized liquid nitrogen injection are discussed and evaluated. Concepts of frozen shaft design are discussed, including a new method for permitting the launch of the Tunnel Boring Machine through the frozen earth wall and associated freeze pipes.

Jan 1, 1999

By K B. Bowley

This paper covers the application of a systematic maintenance plan by the Plant Engineering Department of Rio Algom Mines Limited, Milliken Division. The plan established the function of work study, developed and installed formal work planning and labour cost control procedures, and extended the existing preventive maintenance routines. In June, 1961, assisted by management consultants, a more scientific approach to maintenance was instituted. The emphasis was placed on the control of labour. The development and application of the primary control system was established with-in six months. Since then, the Department has operated for a year, consolidating the system. The procedure of the installation, the results achieved and the results to be expected will be discussed. JNTRODUCTION THE Milliken Division of Rio Algom Mines Limited operates a 3,000-ton-per-day uranium mine, in the Elliot Lake district of Ontario, which went into production in April of 1958. The lowest operating level is 3,000 feet below surface. Mining is carried out by open stopping, with planned pillar support and footwall haulage on rail.

Jan 1, 1963

By A. Haxhiaj, Mitovica, E. Haxhiaj

"The paper discusses problems encountered during the release and possibility of using the thermal gas quantity Mathematical models are used to calculate the positive thermal effects of the gases and losses of thermal quantity with gases in the melting process of electric furnaces. The paper discusses in details the percentages of CO, CO2, H2S, O2 and the humidity in gases and their impact on the technological process in electrical furnaces in Drenas. The paper also confers the quantity and temperature of gases, the transfer of thermal quantity and dust with gases in the environment. The paper presents the percentage of humidity in the load which is added in electric furnace for melting and its impact on thermal and environmental balance in the technological process of melting in electric furnaces. Key words: Furnace, load, temperature, humidity, gases.IntroductionNickel easily reacts with gases in the atmosphere of the furnace in which the nickel ore is processed. Such reactions can explain challenges in producing high quality nickel. Reductive atmosphere with the surrounding gases composed of sulphurous anhydrite has harmful effects on the production of nickel. This is mainly due to solubility of hydrogen as well as nickel oxide in the melted metal. Nickel reacts with carbon monoxide and forms carbide of nickel and nickel oxide which dissolve in the melted metal. Carbon monoxide also dissolves in the melted metal. The presence of carbon dioxide and water vapor in the atmosphere of the furnace impact the decrease of acidity in reductive atmosphere of the furnace. The carbon dioxide reacts with nickel and forms nickel oxide and carbon monoxide. Water vapor reacts with nickel and forms hydrogen and nickel oxide that have negative impact on the structure of nickel and its alloys. In this paper the analytical and experimental analyses are proposed that lead to minimization of the negative effects of gasses and humidity in the melting process. As the practical example, the electrical furnace in Drenas is analyzed.1. The Load and Its CompositionThe basic function of the rotational furnace is drying and reductive roasting of the ore which directly is loaded into the electrical furnace for melting. It is important to mention that the degree of roasting and pre-reduction of iron-nickel oxides is reached if the roasting process of the load in the rotational furnace is done at the temperature of 900°C to 1000°C, with the reductive atmosphere in the furnace and with minimal amount of oxygen in the processing gas. The optimal process of roasting and pre-reduction of the load in its mass is around 13 wt%. With the removal of the humidity and the sterile pare of the ore, with the positive impacts in utilization of the thermal and electrical energy in the melting process in electrical furnaces."

Jan 1, 2013

By Omid Asghari, Seyed Reza Ghavami-Riabi, Sajjad Talesh Hosseini

Separation of geochemical anomalies from the background using various methods for identifying areas of higher mineral potential is a critical first step in Greenfield and Brownfield programs. There are several methods for differentiating anomalous regions from the background. The U-spatial statistics is an effective technique that provides the opportunity of reaching this goal by considering the geochemical sample locations in the separation of geochemical anomalies. In this study, a developed form of the U-spatial statistics method is introduced, which not only considers the existence of anisotropic spatial variations in input data but also reduces the computational (CPU) time. While the previous method is based on the isotropic assumption in the study area and a set of search windows at different times, here, the geochemical anomaly is determined by pasting only one ellipsoid window, effectively combining the flexibility of the U-spatial statistics method with the advantages of geostatistical approaches. This paper compares various approaches (the previous and developed version of the U-spatial statistics method, concentrationarea (C–A) fractal model, and probability diagram modeling) for the separation of anomalous areas in the presence of heterogeneous spatial variations. This is done with an application to a Baghqloom porphyry copper deposit located in southeastern Iran. The high potential areas identified via different approaches show an anomalous region in central parts of the Baghqloom area, which partially coincides with an intense potassic alteration area. Compared to other methods, our algorithm separated the high potential areas at a greater spatial resolution.

May 3, 2021

By B. M. Eiter, J. Hrica, D. R. Willmer

"Mineworkers are routinely tasked with making critically important decisions about whether or not a hazard presents an imminent danger. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected formative data to investigate mine safety professional perspectives on workplace examinations, which revealed a potential gap in how mineworkers are assessing risk. During interviews, participants indicated having processes in place for what should be done once an imminent danger situation is identified. Critically, however, they report having no systematic methodology for mineworkers to use to determine if a hazard is considered imminent danger. While this is important for all imminent danger situations (e.g., failure to lockout/tagout), it is especially important for those situations that are not immediately recognizable as imminent danger. In this paper, we identify and describe, three distinct categories of imminent danger complexity and discuss potential steps that could lead to improved identification of imminent danger situations. Finally, we identify potential practices to incorporate into risk management efforts, including feedback, communication, and specialized training to increase awareness of imminent danger situations. INTRODUCTION In recent years, the metal and nonmetal (M/NM) mining sector, as categorized by MSHA, experienced an increase in the number of fatalities occurring at mine sites. From 2013 to 2015, 69 mineworkers were fatally injured; that is twice the number of fatalities that occurred in each of the previous two years (MSHA, 2015a). As a way to address this increase, the Mine Safety and Health Administration (MSHA) issued a program policy letter (P15-IV-01) suggesting that “miners would benefit from rigorous workplace examinations conducted by experienced and trained examiners (MSHA 2015b).” The goal of workplace examinations is to find hazards in the field and mitigate them before they cause injury or death to mineworkers. While it is important to identify all hazards in the workplace, it is critically important to identify those hazards that are considered imminent danger because they require an immediate response to avoid a severe or even fatal injury."

Jan 1, 2018

By Eugene W. Bartel

This report describes in detail the circuitry used in the Automated Time Domain Reflectometry System and the testing and modification done to the system to improve the units performance and consistency. The analog ATDR software is described and explained in detail. Also attempts to implement the same Assembly Language program in a higher level language (PLM) are documented along `h two versions of the PLM program - one which uses a data filtering approach to limit noise and another which uses data averaging to reduce noise. The field testing of the analog and digital ATDR units is described along with the hardware modifications that resulted. The analog unit has been abandoned and the digital unit adopted for most field tests. Tests indicate that the digital units are much more consistent and less confusing for the lay-person to operate. The results indicate that the it can locate an abnormality in a test cable to within 5% of the true location (provided the cable phase velocity is known). The units can consistently locate shunt type faults which are less than 300 ohms and series type faults which are greater than 30 ohms.

Jan 1, 1980

By Christoph Sedivy

Industrie 4.0 is slowly but surely arriving in the melt shops. Furnaces are being equipped with more and more sensors, digital models are increasing the degree of automation, and information is being shared between different aggregates within the plant. Because the electrode control system plays a key role in electric steelmaking, it naturally assumes an important position in the melt shop’s Industrie 4.0 strategy. In addition to reliable, state-of-the-art core regulation functionality, monitoring and reporting tools and the ability to communicate with other equipment are also required. Therefore, the latest generation of our electrode control system, the Melt Expert, was developed based on Industrie 4.0 design principles. Intelligent plant condition diagnostics, performance monitoring, and user-defined reporting are essential modules in this new system. With these functionalities, electrode control systems are developing into the information and control center of the furnace. A newly developed software app brings most relevant process information to mobile devices. This feature allows steelmakers to keep an eye on the performance of their equipment anytime and anywhere. This paper describes the new features of the electrode control system and shares our customers’ operational experience. Our focus is on the practical aspects of plant status monitoring, KPI reporting, and diagnostic functionality as well as the improvements achieved.

Oct 30, 2017

By E. Chin

Although Japan is a major producer of crude steel, it is poor in industrial raw materials. This Bureau of fines report describes Japan's raw material needs for chromium, cobalt, manganese, nickel, and tungsten to produce ferroalloys and alloy steels. Japanese imports of these ores or metals by quantity and source are given for 1972-81, inclusive, to indicate (1) the changes in the consumption and supply pattern, and (2) the degree of Japan's dependence on foreign sources. This report also describes measures implemented by Japan to reduce the risk- of supply interruption, and discusses the possible implications of supply shortages.

Jan 1, 1983

By Ronald W. Stingelin

This study undertook the development and implementation of a methodology for estimating the impact of coal seam interaction on the eastern bituminous underground reserve base as published in USBM Information Circular 8655. The effects of previous mining in multiple coal seam areas on currently mined and reserve seams are predicted as a percentage coal loss by an engineering assessment model called the Coal Loss Calculation Model. The model utilizes twelve input variables easily derivable from mine maps or other existing data sources and calculates the effects of subsidence and high-stress due to remnant pillars in the previously mined seam. Extensive literature review resulted in the identification, definition, and quantification of the critical variables of seam interaction. Export opinion surveys were made of mining experts, MESA mine inspectors, and coal mine operators. Statistical analysis was used to establish the redundancy of the critical variables and to develop a total coal loss prediction algorithm. A regional analysis resulted in the production of a series of thematic maps on coal characteristics and distribution. A derivative map showing the areas of commonality within the eastern bituminous coal region served as the basis for implementation of the coal loss calculation model. The model was developed and tested using data from four coal mines in western Pennsylvania and southern West Virginia.

Jan 1, 1976

By R. C. Adams

This report describes the feasibility of mining the oil-shale deposits of the Piceance Creek basin in Colorado by an integrated open pit system. The study is based upon a comprehensive analysis of pertinent environmental, economic, and engineering factors. Ten mining cases are investigated, and the mine design and cost estimates for each case are presented in this report. Nine of the cases represent three cutoff grades, defining oil shale ore as equal to and above 15 gallons per ton (gpt), 20 gpt, and 25 gpt, at three ore production levels of 500,000 tons per day (TPD), 1,250,000 TPD, and 2,500,000 TPD. The tenth case is an alternate design of the 500,000 TPD production rate at the above 15 gpt cutoff grade. The report consists of Volume I, a technical and cost comparison of the ten cases; Volume II-Part I, a detailed explanation of the estimating methods used; and Volume II-Part 2, a more detailed discussion of the technical and cost features of the ten cases than is presented in Volume I.

Jan 1, 1976