Search Documents

By James O'Brien, Lyman Frost, Grant Hawkes, S. Elangovan, Manohar Sohal, J. S. Herring, Joseph Hartvigsen, Carl Stoots

"Pressing environmental and energy security concerns have brought much needed attention to economic production of hydrogen as the secondary energy carrier for non-electrical markets as well as to meet increasing demand for crude upgrading and desulfurization. While steam reforming of natural gas is currently the dominant method of hydrogen production, it is depleting a valuable fossil fuel while emitting green house gases. Thus, in the long run, efficient, environmentally friendly, and economic means of hydrogen production using nuclear and renewable energy needs to be developed. High temperature electrolysis using solid oxide electrolyte cells is an exceptionally efficient means of generation of high purity hydrogen. It is also capable of directly converting steam and CO2 into synthesis gas. This co-electrolysis process enables conversion of CO2 recovered from concentrated industrial sources into a feedstock for synthetic fuels production. Use of CO2 provides a means of storing hydrogen in a concentrated and convenient form – a hydrocarbon. This is also an effective storage medium for intermittent renewable energy sources such as wind and solar.Ceramatec, Inc and the Idaho National Laboratory are applying solid oxide fuel cell technology to the production of synthesis gas by high temperature co-electrolysis of steam and carbon dioxide. This technology utilizes solid oxide fuel cell stacks to electrochemically remove oxygen from steam and CO2, leaving a clean stream of hydrogen and carbon monoxide suitable for fuel synthesis. By varying the relative concentrations of carbon dioxide and steam, the hydrogen to carbon monoxide product ratio can be controlled as required by the desired type of synthetic fuel being produced from the syngas. The resultant synthesis gas has been used as the feedstock to produce synthetic methane and Fischer Tropsch liquid fuels.Alkaline and proton exchange membrane electrolysis cells typically operate below 100°C, while solid oxide electrolysis cells operates in the 750-850°C range. This higher temperature improves the efficiency significantly. Practically, it translates into a lower cell operating voltage, 1.1-1.4V for high temperature electrolysis vs. ~1.8V for water electrolysis. Hydrogen production is stoichiometric with current in all types of electrolyzers.Carbon dioxide is a valuable resource as a feedstock for energy storage as a hydrocarbon. There is a vast amount of renewable energy that cannot be effectively utilized as grid electricity, but which could be used to convert CO2 to hydrocarbons, offering a solution to the even more difficult (than supplying grid power) challenge of production of sustainable, domestic transportation fuels. Conventional electrolysis and chemical processes could be deployed to accomplish this conversion. However, high temperature co-electrolysis of CO2 and steam to produce synthesis gas using solid oxide fuel cell technology has the potential of improving the efficiency by nearly 50%. A domestic synfuel industry will enable a much larger reliance on intermittent renewable energy than can be accommodated by conventional electric demand profiles while increasing our energy security."

Jan 1, 2010

By F. Sundqvist, B. Skawina, J. Greberg, A. Salama, M. Astrand, P. Ekbeck

Today’s mining operations require fast reporting and rapid rescheduling based on updated information. An automatic mine scheduling system could not only quickly reschedule but also propose alternative solutions. To avoid the financial and physical risks associated with testing such a system directly in operation, it could be first evaluated via discrete event simulation models. This would offer a safe environment to evaluate different operating rules and algorithms. In this study, this is achieved by integrating automatic scheduling software with a discrete event simulation model.

Jun 1, 2021

By D. F. Doerr, E. Blalock, D. R. Bush, K. D. Cohen

"INTRODUCTION The design, development, fabrication, and test of cryogenic breathing apparatus is part of a much larger effort funded by the National Institute for Occupational Safety and Health (NIOSH) and managed through a Space Act Agreement with the National Aeronautics and Space Administration (NASA) at the Kennedy Space Center (KSC) in Florida. This effort is designed to create cryogenically based life support equipment that is responsive to the needs of miners as required by the Miner Act of 2006. Our goal was to design and build a liquid air based self-contained breathing apparatus (SCBA) that lasted 2 hours and would be used for the egress of miners during a mining accident and be refillable while worn. Therefore, the current report describes tests of an Advanced Cryogenic Breathing Apparatus (termed the ACryoBA) designed to provide miners egressing an emergency situation with a two-hour open-circuit SCBA. The ACryoBA utilizes low pressure cryogenic liquid air instead of high pressure compressed air commonly used in most commercially available SCBA. The ACryoBA can also be self-filled from strategically placed Cryogenic Air Supply and Fill Stations (CryoASFS) initially, and thereafter on the egress route approximately every 1 hour and 30 minutes with a 30 minute air reserve. The ACryoBA evolved originally from a one hour Liquid Air Pack (LAP) developed in the 1980’s for Space Shuttle Rescue forces allowing for longer duration and cool air (Figure 1). It was used successfully for many years, through the end of the Space Shuttle Program. The first attempt at a mine egress pack was the Cryogenic Breathing Apparatus (Figure 2). It was to have a low profile, two hours of breathing, attitude independence, and a simple rapid refill while in use. The CryoBA met the two hour criteria, but with difficulty due to excessive heat leakage caused by the dual 4 liter Dewar design. Much of the stored air was lost as it vaporized faster than it could be used. However, the pack was successful in demonstrating both attitude independence and a simple rapid refill capability. The ACryoBA project was designed to continue the progression and address the deficiencies in the CryoBA. The ACryoBA pack was designed to last 2 hours. It minimizes the heat leakage with a single Dewar and thereby requires less liquid air. The single Dewar design also minimizes weight, making it much more manageable by the user (Figure 3). The ACryoBA complies with 42 CFR part 84 NIOSH certification test requirements. One critical requirement for the ACryoBA is operation in positions other than vertical for periods up to 1/4 (i.e. 30 minutes) of the rated service life of 2 hours; this was accomplished by use of new technology called the “attitude independent pickup” which is abbreviated “AIP.” The AIP, developed by BCS Life Support LLC (patent #8,899,226), has a tube going from the top flange down through the center of the Dewar. At the end it has a flexible bellows and a weighted end. Due to the flexible nature of the bellows, the pickup at the end is free to rotate and follow the liquid level around within +/- 90o of vertical."

Jan 1, 2016

By Gregg W. Davidson, J. Andrew McGlenn, Frank Huber

The Second Narrows Water Supply Tunnel will ensure system reliability in the event of a major earthquake and increase the Greater Vancouver Water District’s capacity to meet the long-term needs of a growing population. The tunnel will be 1,100 m long and 6.5 m in diameter (3,610 LF × 21.3 ft), constructed under Burrard Inlet between North Vancouver and Burnaby in British Columbia. It will be excavated through mixed ground conditions under high groundwater pressure, using a slurry TBM, between a 72 m (236 ft) deep shaft in soil and a 110 m (361 ft) deep shaft in rock. The completed tunnel will accommodate three large-diameter water mains that will be installed as part of the tunnel contract. This paper presents the project from design and contractor procurement, into the current construction stage describing some of the unique challenges encountered during the project development to date.

Jun 13, 2021

By R G. Moreby, S Bluhm, FávonáGlehn, C Pascoe

Resolution Copper Mine in Arizona, USA, is planned to be a 2000 m deep panel cave mine with virgin rock temperatures exceeding 80¦C in rock with high crystalline silica content, resulting in a very challenging ventilation and cooling system design. This is one of the largest copper orebodies ever found and, with a planned rock production rate of 120 kton/day. The project is currently in its prefeasibility phase and the paper discusses features of the ventilation and cooling system design which includes multiple ventilation shafts with total primary ventilation flow of about 3000 m3/s and both surface and underground refrigeration plants producing more than 140 MW refrigeration capacity. The cooling system features large surface bulk air coolers chilling all downcast air supplemented by an underground secondary air cooler system and a chilled service water system. This will be a very challenging mine to ventilate and cool but this work has demonstrated that it will be technically achievable with the application of existing technology.CITATION:Bluhm, S, Moreby, R G, von Glehn, F and Pascoe, C, 2013. Life-of-mine ventilation and refrigeration planning for Resolution Copper Mine, in Proceedings The Australian Mine Ventilation Conference , pp 125-138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Gerald M. Bandholz

Exxon Minerals Company, a division of Exxon Corporation, has been exploring for base metal deposits in the Precambrian volcanic rocks in northern Wisconsin since 1970. Aerial electromagnetic surveys of the area, conducted in 1974, reported an anomaly, near Crandon, in Forest County. In the summer of 1975, the first diamond drill entered the anomaly, representing the 25th prospect Exxon had drilled in Wisconsin. This first hole revealed significant mineralization containing zinc and copper. Subsequent drilling confirmed the discovery of a sizeable zinc-copper massive sulfide are body. 1.1.2 Location The deposit is located in northeastern Wisconsin within a topographical high called the Northern Highlands region. The deposit lies about 5 miles directly south of Crandon and about 2 miles east of State Highway 55 on Sand Lake Road (see fig. 1). Other local communities include Rhinelander 28 miles west, Antigo 45 miles south, and Iron River and Iron Mountain, in Michigan, 75 and 44 miles east and north of Crandon respectively. In relation to the lakes and streams, the deposit lies 0.25 miles north of Little Sand Lake, and about 1 mile south of Swamp Creek.

Jan 1, 1981

By John S. Carman

Our industry is in trouble. Real trouble. It has never been an easy, secure business. But to-day it is engulfed in revolutionary currents. No longer can there be reliance upon the checks and balances of market forces. Supply and demand largely dictated the economics of business enterprise in simpler days. To-day politics, in particular nationalism become increasingly dominant. And as governments expand and put out tentacles of interference in the direction of the mining industry, far too little understanding is evidenced as to how that industry works. Then there is something which is relatively new -stagflation. As the prices of minerals falls, the capital investment required for new extractive facilities soars at rates which far outdistance those which are cited by governments to indicate the magnitude of inflation. To illustrate; 1) In 1971 it was calculated that $355 million would be required to bring the Cuajone property in Peru into production. Five years later that stage was reached at a cost of $680 million. 2) With the Caridad mine in Mexico, estimated capital investment doubled between 1971 and 1976. 3) The requirements calculated for Cerro Colorado in Panama have risen in two years from $560 to $800. 4) The budget of $240 million for Sar Chesmeh in Iran in 1971 had become $500 million by 1976.

Jan 1, 1977

By Herty, C. H.

Present-day interest in the question of "dirty steel" has arisen primarily from the increasingly rigid specifications on various grades of steel and from the growing conviction that non-metallic inclusions are the source of many of the difficulties in meeting these specifications. The importance of inclusions has unquestionably been over-emphasized in many cases, but on the other hand many unpublished instances could be recorded where all evidence pointed to inclusions as the primary cause for the failure of steel in rolling or in service. The solution of the problem of dirty steel is not a matter of a few years. There are almost numberless types of inclusions. They segregate in steel ingots in an entirely different manner from other impurities, and, at best, only a start has been made in developing correct analytical methods for their determination. Most of the writers in the field have expressed opinions rather than given facts, and so many variables enter into the manufacture of steel that a study of plant conditions is difficult unless definite facts on certain phases of the inclusion problem are available. This statement is not intended to convey the idea that little work has been done on this problem. On the other hand, the number of investigations has been large, but in most cases too many variables have been present to allow definite conclusions to be drawn. In the body of the text, reference to previous investigations is made at suitable points. Rather than burden the reader with a lengthy review of the literature on the general subject of inclusions, reference to the particular works pertinent to the subject matter of the bulletin has been discussed. Three excellent bibliographies b on the subject have been lately published: one by the Committee on

Jan 1, 1957

By G M. Evans, C M. Phan

This paper presents an analysis on the dynamic adsorption of frothers and collectors onto air bubbles in flotation. The analysis was carried out using the theory on the surfactant transfer by diffusion and adsorption. The bubble size was considered when solving the diffusion equation for the dynamic surface excess. The adsorption kinetics was modelled employing the Langmuir adsorption isotherm and its extension with the inclusion of the lateral interaction of the adsorbed molecules (the Frumkin adsorption isotherm). The numerical computation was applied to solve the governing equations. The dynamic adsorption of the surfactants was measured in terms of the dynamic surface tension for sodium dodecylbenzene sulfonate (SDBS) and Dowfroth 250, using pendant bubble tensiometry. The results show that for air bubbles with diameter of the order of 1 mm, the bubble size effect on the dynamic surface tension is small and the solution of the diffusion equation for a planar gas-liquid surface can be used to describe the dynamic adsorption onto the air bubbles. The experimental data obtained with SDBS were well described by the Frumkin adsorption isotherm and the molecular diffusion. The model description for the experimental data obtained with Dowfroth 250 required the kinetic equations. The paper is relevant for further analysis of the role of the adsorbed surfactants in the particle collection.

Jan 1, 2005

By R. L. Marek

An important problem in the efficient conduct of industry is that of helping the individual employee to formulate an attitude toward his work which will result in the reduction of accidents and the promotion of safety. Perhaps nowhere is the need greater for this type of Psychological training of carefully selected men than at oil refineries whore both the raw materials and the finished products are highly inflammable and explosive in nature. However, the refinery organization usually is well adapted to educational safety activities - much more so than in the producing, pipe line, and marketing departments where the personnel are more or less scattered; but the same general principles of conduct hold true in any industrial organization. This problem of directing the attention of the employees to their specific tasks or helping them to control and frequently eliminate hazards engendered by adverse mental attitude or emotion is met most satisfactorily by carefully selecting applicants and placing them at jobs for which their ability, best fits them. The subsequent training of these carefully selected employees to assure their most effective work in accident prevention mu be accomplished in a variety of ways, such as by personal supervision and instruction, inspections, drills, and by the studied use of well thought out safety pamphlets and posters. This procedure is simple in outline and not original in scope, yet the importance of selecting and training the personnel has, not been generally accepted by the petroleum industry until recent years. In 1926, the Bureau of Mines, while making a study of accidents in the petroleum industry, found that medical examinations of prospective employees were not receiving unanimous endorsement by all companies, and the point was stressed that the selection and allocation of employees was a problem requiring serious consideration in the petroleum industry.

Jan 1, 1932

By J. Bootle

Marrow vein deposits will continue to be an important source of valuable minerals. Productivity per manshift is not keeping pace with operating costs. Increased mechanization of stoping operations must be obtained to create greater productivity at a reduced cost per ton. This application of mechanization may be to either present methods or to newly developed concepts. The total mine unit operations will be effected by increased productivity. Two approaches to increasing the mechanization of narrow vein stoping were studied with the intention of increasing stope productivity and decreasing stoping costs. A method of bringing efficient rubber-tired equipment into narrow cut and fill stopes was designed. It proposes to provide stope access by way of a ramp constructed on the stope fill. Impact breaking equipment was studied and specific applications proposed.

Jan 1, 1977

By Harrison H. Roberts

A. We are aware that many who are in the audience have perhaps heard before some of the material which will be presented. Since our firm is more closely associated with the heavy construction industry our experience is more oriented in that direction. Notwithstanding this, the subject your program committee has asked us to present centers mainly in the earth-moving field. We find a common denominator between say, the stripping of a site to uncover an ore-body which will be developed by open-pit methods, and that of excavating & transporting materials for an embankment dam, airport or other project. Both are earth-moving problems and we offer for your consideration a means of determining the most favorable method, equipment selection and resultant cost. We do considerable studies involving rock excavation for tunnels, underground powerhouses, inclined and vertical shafts for penstocks, muck-removal, electrical cable & other related underground work. Hence, we believe we speak the same language.

Jan 1, 1972

By Derrick Dasenbrock, Mary C. Nodine, Benjamin Rivers

Up to 50 percent of major infrastructure projects suffer impacts to schedule or cost due to geotechnical issues, many of which correspond to risks related directly or indirectly to the scope and quality of site characterization work. The Federal Highway Administration (FHWA) in coordination with industry organizations seeks to address this issue through Every Day Counts (EDC), a program that identifies and deploys proven, yet underutilized innovations at the project level to save time, money and resources. The A-GaME (Advanced Geotechnical Methods in Exploration) is one of the innovations supported under EDC.

By Lawrence W. Scott

This report presents several systems for continuously monitoring the quality of air in underground mines that are being developed by the Bureau of Mines. Underground stations measure methane, carbon monoxide and nitrogen dioxide concentrations, air velocity, and air temperature. This information is transmitted over a single telephone pair to central stations located on the surface. The central stations display alarms and the data is selectably displayed on digital panel meters.

Jan 1, 1977

By C. S. Gibson

"MOST of the mines in the Province of Ontario in Canada are multi-level operations in steeply dipping veins; yet there is an appreciable number whose de-posits are relatively flat-lying, ranging up to 45° inclination.The veins vary in width up to several hundred feet and may or may not be branching systems. The depths of mines range from a few hundred to 8,000 feet, approximately. The primary products of the underground group are asbestos, gold, silver, cobalt, copper, nickel, iron, uranium, talc, fluorspar, gyp-sum and salt.There are a few open-pit mines. The majority are temporary in type because, as the outcrops are removed, mining is continued be-low surface. Primary products of the open pits are copper, nickel, iron, magnesium and nepheline syenite.The industry as a whole employs about 50,000 persons, approximately 60 per •cent of whom have dust-exposure occupations. The definition of a dust-exposure occupation and the requirements for •dealing with same are set forth in The Mining Act of Ontario.Results of extensive and continuing studies on the incidence and progression of silicosis have been reported periodically for years past, in annual reports of the Mines Accident Prevention Association of Ontario and in papers presented at Conferences sponsored by Mcintyre Research Foundation of Toronto, all of which have been published. The information provided therein proves the effectiveness of the means being used to prevent silicosis and allied disorders."

Jan 1, 1960

By S. Pule, Z. Ndabezimbi, A. Hefer, E. Cupido

This article outlines various projects implemented at Rand Refinery to reduce effluent generation and freshwater consumption. The refinery generates about 2800 m³ of effluent annually and has initiated projects such as granulation water recycle and silver leach optimisation to address these issues. The granulation water recycle project has successfully reduced effluent volumes, while the silver leach optimisation has further decreased effluent by implementing stoichiometric addition of HCl and NaClO3. The vibratory shear enhanced processing (VSEP) trial showed promising results for gold recovery from wastewater, though further trials are recommended. The water savings of the effluent reduction projects are monitored by measuring the amount of effluent pumped to service yard effluent storage facilities with the use of flow meters connected on SCADA. Since the effluent reduction initiative of granulation effluent recycle in FY23, the effluent reduced to 2676 m³. In FY24, the stoichiometric addition of HCl and NaClO3 was implemented in the silver leach process, further reducing the effluent to 2083 m³.

Mar 5, 2025

By F. Calizaya

A booster fan is an underground ventilation device installed in the main airstream to handle the total quantity of air circulated to one or more working districts. It is installed in a permanent stopping and equipped with airlock doors, a monitoring system and interlocking devices between the main fan and the booster fan. When adequately installed, a booster fan can be used to reduce the main fan pressure, reduce leakage and decrease the power consumption. However, an inadequate installation can increase the likelihood of mine fies and recirculation of air contaminants. This study identifies hazards associated with the operation and maintenance of booster fans. It analyzes the accompanying risks and recommends control measures to reduce those risks to acceptable levels. The ventilation network of an existing coal mine was updated to include a booster fan. The hazards associated with the operation of this fan were identified, the risks analyzed and the esponse to each failure mode established.

Mar 1, 2014

By J. D. Noll, J. A. Organiscak, A. B. Cecala

Over the past decade, a substantial effort has been made to improve the air quality inside enclosed cabs of both underground and surface mobile mining equipment to reduce respirable dust exposures by the equipment operators. As part of this effort, the U.S. National Institute for Occupational Safety and Health, (NIOSH) completed a comprehensive laboratory study that determined the significant factors for cab filtration and pressurization systems. From this information, a major underground mining equipment manufacturer designed a filtration and pressurization system that was incorporated into the enclosed cabs of its equipment. A long-term evaluation was performed on the effectiveness of this filtration and pressurization system to improve the air quality in the enclosed cabs of two different pieces of equipment, a face drill and a roof-bolter machine, at an underground limestone mine. This long-term evaluation demonstrated a significant reduction in dust levels between outside-to-inside cab respirable dust concentrations. During this evaluation, a modification to remove one of the filters on the roof-bolter machine simplified the design without sacrificing the system’s efficiency. Tests using particle count instruments performed during nonproduction time periods on both pieces of equipment indicated protection factors greater than 100 when comparing respirable-sized dust particles inside the enclosed cab relative to outside.

Jan 1, 2012

By C. N. Logan

The Southern Company is one of the nation's largest electric utilities and is the parent firm of five operating companies: Alabama Power, Georgia Power, Gulf Power, Mississippi Power and Savannah Electric and Power. Another subsidiary is Southern Company Services (SCS) which provides engineering and technical sup-port to the five operating companies. This technical support includes the procurement and supply of over 40.9 Mt (45 million st) of coal annually for the 22 coal fired plants in the system. Approximately 80 percent of this tonnage is purchased under long term contracts and the remaining 20 percent is purchased on the spot market. The coal is principally supplied from Alabama, Illinois Basin and the eastern Appalachian coal fields. Most of the coal is delivered by unit train and barge but one plant in Alabama receives all its coal by truck and conveyor belt.

Jan 1, 1990

The Iron and Steel Committee of the American Institute, of mining and Metallurgical Engineers held a joint session with the American Foundrymen's Association during the Annual Meeting of the Institute in February, 1928, for the purpose of discussing blast-furnace operations and the character of pig iron and castings. Dr. Richard Moldenke presided. H.. H. Sweetser, who was named on the program as the presiding officer of the session, was unable to be present, but sent a letter in which he said: " The meeting we had here last year and the meeting held in Chicago last June showed a desire on the part of blast-furnace men and users of pig iron to get the facts regarding the influence on castings made from pig iron produced in blast furnaces under varying conditions of temperature, mixture and local furnace operations. It has been my hope that at this Round Table we might he able to formulate a series of tests that, would give us the desired information. "Several independent blast-furnace investigations have. been, and still are being, carried on in different sections of the country. The furnaces investigated include a southern furnace, a middle-west furnace, a western furnace and a Chicago district furnace. The results so far show distinct characteristics for each of the four furnaces. It is possible that a furnace in the eastern part of the United States would be different from all the others. "It is hoped that a plan of action can be worked out at your meeting today whereby the IT. S. Bureau of Mines will be able, to carry on more extensive work in connection with the research departments of the different iron and steel companies and the big consumers of pig iron. "No one group can get all of the, information but if the different investigations can be coordinated it will he possible for us to (Iran. conclusions regarding the effects of varying conditions in blast-furnace practice on the pig iron produced and the castings made there from." DISCUSSION R. Moldenke, Watehung, N. J.—I was across the -water this summer and saw some of those interested in an investigation of this kind. 'I'hey told me that in Germany, where they had a joint committee of blast-furnace operators and foundry-