Search Documents

By Song Jiang, Xianzhi Tan, Minjie Lian

"The ground water heat pump system lades underground hot water which can be heated or cooled by heat exchanger in water source heat pump air conditioner. This system replaces the model of heating of air-conditioning by refrigerator and boiler. In this paper, the formation conditions of hot water energy in Shan Dong are analyzed in order to achieve the purpose of energy conservation and emissions reduction by taking full advantage of water resources such as water pouring and return water of beatification during the productive process of underground metal mine. In order to analyze the issue better, the paper points out some ways and methods for geothermal water often used in underground metal mine. This paper also presents the advantages of the technology of water source heat pump that is applied into underground metal mine. Here is a case study of comprehensive utilization of water source in a certain underground metal mine in Ji Ning. This mine, according to its own actual situation, designs heat pump heat exchange system which is used for indoor heating of buildings and bath for staff. It turns out that the system can save 23% water per year, cut down 3.303 million KW electric energy, and reduce 4160t emission of carbon dioxide. It is concluded that the technology of water source heat pump has broad application prospects in underground metal mine. Therefore, the results show that it is an ideal way to change the present structure of cooling and heating source in metal mine.Introduction In recent years, overuse of fossil fuels has posed a grave threat onto the environment, which makes renewable energy a more important status in energy structure. Development and utilization of renewable energy has become an important direction. Water source heat pump technology is to use solar energy stored in water as cold/heat source to convert energy. Currently, this technology has been widely used in some advanced countries. However, due to facers of implementation technology and component costs, there is still a gap in water source heat pump technology between China and these advanced countries. According to (Blum et al 2011) that after in-depth study, water source heat pump technology has developed rapidly in China recently, and the gap is gradually reduced. Groundwater source heat pump system as a kind of high efficiency, energy-saving and environmentally friendly technology in recent years, more and more get the people's attention. At the same time, its practical application has also been rapid development. Based on (Ni et al 2015) that According to the relevant departments of the prediction, the technology will become the 21st century the most efficient heating and cooling technology."

Jan 1, 2017

By G. Richards

The Trail smelter of Teck Metals Ltd. produces about 90,000 tonnes of lead per year through two stages of refining following KIVCETTM smelting. Bullion from the KIVCET furnace is first treated in a pyro-refining plant in preparation for Betts electrorefining which makes 99.99% pure lead. Pyro-refining consists of number of integrated unit operations to remove primarily copper, arsenic, antimony and tin. The operation of this plant to meet the specifications for electrorefining requires attention to bullion management and selective use of reagents. The processes used for pyro-refining are reviewed in terms of chemistry and control.

By S. Frederick Ravitz

JUDGING from the inquiries that are constantly being received by the Utah Engineering Experiment Station as to the "Why," so to speak, of the flotation process of concentrating minerals, it occurred to me that perhaps a brief statement of the more important theories might interest those who have not followed the technical literature. Like many other industrial processes, flotation has hitherto been developed on an almost purely empirical basis, with relatively little practical contribution from the fundamental chemistry and physics on which the phenomena are based. In fact, its development by the trial - and - error method has been perfected to such a high state that it is becoming generally thought that further important advances can be brought about only by a thorough understanding of the actual mechanism of the process. Natur¬ally, such a complicated process has brought forth numerous theories, most of which have failed to withstand the test of time. It is significant that no theory has yet been advanced which is universally accepted.

Jan 1, 1933

By Wenzhou Yu, Cong Zhang, Wenhui Ma, Gang Wang, Kuixian Wei

"A novel technique was successfully developed for nickel further purification by vacuum directional solidification. The removal effect of impurities in nickel was studied based on theoretical analysis and experiments. High removal efficiency of impurities in nickel can be realized according to theoretical analysis. The experimental results show that the vacuum directional solidification treatment could increase the nickel purity from 99.96% to 99.996%. Since vacuum directional solidification could effectively remove the impurities from nickel with low contamination and low cost, it is a potential route to obtain high-purity nickel for commercial application.IntroductionNickel is widely used in metallurgy, machinery, petroleum industry, chemical industry, construction industry, light industry, and other industries for its ductility, medium hardness, ferromagnetism and high chemical activity. Nickel-based alloy is an important material for the key parts of aircraft, tanks, submarines, radars, nuclear reactors and aerospace fields [1-5]. Generally, nickel contains Si, P, S, Fe, Cu, Zn, As, Cd, Sn, Sb, Pb, Bi, Al, Mn, Mg and other impurity elements, which may hinder the commercial application of nickel. Therefore, it is necessary to refine the crude nickel for the high purity nickel."

Jan 1, 2014

TO THE, BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen -The following report covers briefly some of the more important activities of the Institute during the year 1923. In my report for the year 1922, I drew attention to the falling off in membership of the Institute due to the depressed condition of the mining industry in several lines and the inability of many of our members to find profitable employment in mining or its associated branches. A number who were unemployed during 1922 established connections during 1923, but a still greater number have been forced to resign or drop their membership during 1923 Fortunately, the number dropped is not so great as in the previous year. The Employment Service conducted by, the four Founder Societies bears witness to the trend in business For the young men just out of college, there are plenty of opportunities at small salaries, there are plenty of opportunities for them as laborers; but for the mature members, those of experience, there are few calls During the last eighteen months, our Employment Service has been able to place only six of our members out of every hundred engineers for whom it has found work. Another loss which this Society has suffered, but which is not felt so keenly by our sister societies, is in its foreign members. The A. I M. E. has always had a large foreign membership, but of recent years exchange has been so heavily against many European and South American coun¬tries that a large number of members residing abroad have been compelled to relinquish their membership Almost invariably these members express keen regret because of the necessity that confronts them, and almost invariably the writers express hope that present conditions will not last long and that they will soon be able to ask for reinstatement. Having stated the darkest side of the picture first, it may now be drawn to your attention that in spite of these losses the number of persons applying for membership was decidedly encouraging. From the quality point of view, the membership has not gone back¬ward The Membership Committee has declined to recommend many

Jan 1, 1923

By A Millar, B Wraith

Process plants are characterised by variability of performance over a wide range of time-scales; reflected in fluctuations in metal recovery, concentrate grade, plant throughput and reagent costs. In turn, these fluctuations impact financial metrics such as operating costs and revenue. The primary cause of plant variability is variation in the physical, lithological and mineralogical characteristics of the ore fed to the plant. The variability of the ore is driven by the intrinsic heterogeneity of the geology and mineralogy of the orebody, the mining method and mine production plan, the capacity to stockpile and blend, as well as the plant flow sheet and the level of plant automation. Whilst the impact of ore variability on process plants is universally recognised, it is rarely quantified in financial terms. Consequently, opportunities to reduce its impact are often overlooked due to the lack of a basis for a quantifiable cost-benefit analysis to justify improvement initiatives. This paper will present case studies using production data from the Renison tin concentrator and a zinc concentrator. These case studies demonstrate that as the standard deviation of plant head grade increases (as a proxy for ore variability), plant metal recovery subsequently reduces. The metal recovery is then converted into plant revenue losses, to quantify the economic impact of ore variability. The Renison case study demonstrated that whilst a very rare occurrence, revenue losses were as high as 34 per cent (relative to the baseline) when standard deviation was at its highest. The zinc concentrator case study demonstrated that revenue losses were as high as 6 per cent (relative to the baseline) when standard deviation was at its highest. Options are available for reducing and managing ore variability in the process plant. These options include changing mining practices so that the ore is fed to the plant with less variability, more advanced process plant control systems and the use of predictive geometallurgical models.

Aug 24, 2022

By C. D. Harrison

This paper presents the results of 18 high-G centrifuge tests performed at the Electric Power Research Institute's Coal Cleaning Test Facility in January 1985. These tests, using -28 mesh (0.6mm) froth flotation product, show that the high-G, solid-bowl centrifuge can produce clean-coal moistures of less than 12 percent at solids recovery rates exceeding 98 percent. The high-G centrifuge achieved these low moistures by applying centrifugal forces up to 2,000 times gravity. Because these forces are two to three times the forces used in a screen-bowl centrifuge, the high-G centrifuge can use a solid bowl and still produce a low-moisture product. The solid bowl captures ultrafines that would pass through a screen bowl, and thus obtains higher recovery rates than a screen-bowl centrifuge.

Jan 1, 1985

By K. C. Lahiri, H. P. Das, G. G. Sarkar

"The petrographic components of any particular rank of coal often show some distinct physical and chemical characteristics. Therefore, their pro-portionate distribution in a coal greatly influences the technological behaviour of the coal.In any size or gravity separation of a coal, the petrographic constituents become segregated to different degrees in some preferred size or specific gravity range. Therefore, a knowledge of the petrographic nature of the washed and/or screened fractions is often considered essential in selecting the most efficient method for coal preparation and in exploring the proper evenues for its utilization.A graphical method is described in this paper to indicate the mineral-matter content and the petrographic components of the washed fractions of a coal at different ash levels of separation in the form of a new washability diagram. This diagram can be conveniently used to assess or predict the petrographic composition of clean coal or sinks corresponding to any desired ash level in the cleans. With the help of this diagram, it is also possible to locate the yield level of cleans at which maximum enrichment of vitrinites and exinites occurs with the least amount of mineral-matter content."

Jan 1, 1971

By Paulo Conceição, Carlos Sampaio, Carlos Petter, Ariane Kuerten

The Sensor Based-Sorting technology is an emerging technology applied in mineral separation and concentration. The technique consists in using a method known as Dual Energy X-ray Transmission sorting (DE-XRT). The particle's position over the conveyor belt was evaluated and, despite de variability of results, shows that there is no a position with greater accuracy on the sensor's reading. Results obtained indicated that DE-XRT sorting technology was able to significantly reduce the mass and the ash content of the ore feed, being an interesting option for reduction of costs and improvement of coal quality in beneficiation plants.

Oct 3, 2019

By E. A. Twichell

An entirely new concept in the effective utilization of magnetic, energy has resulted in a major break-through in the design of magnetic separation equipment. One of the first applications of this concept has resulted in the development of a Permanent Magnetic Wet Drum Separator with strength .and operating characteristics equal to Electro Wet Drum Separators. Prior to this development when strength and adjustability were required, electro wet drums were specified even with all their drawbacks. The electros, by nature, are subject to coil failure or burnout, over-heating and loss of strength, high power consumption and generally high maintenance. Now the high strength and the adjustability, formerly the exclusive property of electros, has been engineered into permanent wet drum separators. These units combine maximum field strength in the separation zone with strength adjustment to suit changing conditions. Adjustment can be effected while the drum is in operation without stopping either the feed or the drum.

Jan 1, 1967

By Robert Maquil, Gilles Didier, Walter Steiner

"The 1580 m long dual-tube motorway tunnel Markusberg near Schengen, Luxembourg experiences strong swelling phenomena in each tube related to a 35 m wide diagonally crossing rock layer, some150 to 200m from the east portals. Overburden over the roadway is 26 to 30 meters. Tunnel construction started in 1998 and the tunnel was opened in 2003. The tunnel was driven downgrade from the West, the heave phenomenon started to occur as the tunnel approached completion. No indications of the presence of anhydrite and dissolved sulphates were known prior to tunnelling. Water samples had been taken from the beginning of construction and the concentration of anions and cat ions determined. Sulfate content was substantial, in one well it reached 22 mg/l, this high concentration requires the presence of other ions, in particular sodium and chlorine. Based on the knowledge at the time of construction heaving ground was removed from the tunnel invert and a free space was left below the roadway that is covered by a transversely spanned slab. In addition a series of posttensioned tiebacks were installed below the sidewalls. The void left in 2003 was 1.7m high and closed to less than 0.5 meters in 2007 then it became necessary to widen the free space. A central trench was dug with a height of about 2.5 meters and the benches were lowered.Level surveying had been carried out since 2002. In 2006 two extensometers were installed, one in the zone of strongest heave, the second at the edge of the swelling zone. The extensometer in the center of the swelling zone indicated heave with an essential constant rate with seasonal variations, the heave is concentrated in layer from 2 to 5 meters that heaved by nearly 300 millimeters within 5 years or 60 mm/year, which equals to approx. 1% extension per year. At the abutments heave rates of 20 mm/year where the support resistance is higher were observed. With data from other case histories a relation of heave rate with support resistance was established. Based on the numerous field observations hypotheses for the complex in-situ swelling processes, involving rock mechanics, mineralogical, soil mechanics and hydrogeological aspects were developed"

Jan 1, 2015

By M. J. McPherson

Having worked on the thermodynamics of air/liquid-water mixtures passing through the surface fans of deep mines, I find this paper of great interest and congratulate the authors on producing it. There are two matters, however, deserving discussion. First, the authors have described the classical theory of fog formation with fogging occurring at "supersaturation." In fact, the process of fog formation begins well below 100% humidity. The more strongly hygroscopic nuclei in the atmosphere will attract water molecules and begin to grow at a relative humidity perhaps as low as 70%. The process is a dynamic one with both condensation and evaporation taking place throughout the mixture on microscopic liquid surfaces. As saturation is approached, the rate of condensation accelerates rapidly producing the familiar reduction in visibility. Hygroscopic nuclei are present in all natural atmospheres and under the appropriate conditions of pressure and temperature, will produce clean fogs. However, if the air is polluted by particulates from combustion or other processes then the resultant coagulation with growing liquid particles may produce dense (and sometimes photochemical) smogs. It is this process that is likely to occur in underground mines when moist air is cooled below dew point. Second, the authors have summarized very well the individual measures that might alleviate the problem. In particular, I agree that neither heating nor refrigerating the air, by themselves, provides a satisfactory solution. However, there is a combination of these that provides a neat and effective control of fog formation. This involves a small, self-contained refrigeration unit within a duct but without the usual external heat rejection facility. The air is cooled below dew point and, hence, dehumidified on passing over the cold evaporator coils. The heat from the condenser is rejected back into the air down-stream from the water eliminator, as shown in [Fig. 1]. The duct configuration can be designed to create good mixing at the outlet.

Jan 1, 1984

By A. E. McIlhinney, I. E. Puddington, C. E. Capes, A. F. Sirianni

"Two main problems are associated with the removal of pyritic sulphur from coals. The first is due to the fine state of dissemination of pyrite, which requires grindin1 to a very fine size to accomplish liberation. The second problem is caused by the similar surface chemical characteristics of coal and pyrite, which complicates separatio11 methods based on this property. In the work described here, the problem of fine particle size was overcome by using the selective oil agglomeratioa method developed at the National Research Council of Canada. Recovery of more than 90% of the combustible values was possible, even with particles only a few microns in diameter. Experiments using conventional chemical depressants for pyrite met with little success. It was found, however, that pyrite may be rejected during coal agglomeration through treatment with the iron.oxidizing bacteria, thiobacillus-ferrooxidans. The conditions for maximum pyrite separation are described and possible mechanisms by which the bacteria act are discussed."

Jan 1, 1973

By Braden Lusk, Paul Sainato, Josh Calnan, Hiago Vasconcelos, Luis Felipe Marinho

"Blasting and rock fragmentation is one the most important unit operations in mining. Since itsintroduction into the mine production cycle, mining has become more efficient in mineral production(Hartman, 2002). Widely used with the main objective of breaking rock mass in smaller fragments to be loaded and hauled at a minimum cost, blasting is optimized when stemming materials properly confine drillholes charged with explosives. Halim Cevizci (2013) performed a stemming application using Gypsum plaster, a kind of material that exhibits solid-like behavior when it is dry. Based on his theory, the present article reports an experiment using another type of material that shows similar behavior, non-Newtonian fluids. The primary goal of this study is to measure the confinement effectiveness provided by a non-Newtonian mixture as the stemming component. The study also analyzes the explosives’ energy propagation throughout the rock mass relating to the stemming materials applied. Currently, mining literature recommends the application of dry granular materials in stemming columns, because of its inertial and high frictional effects (Hagan, 1973). However, the test verified that the mixture added to the stemming column was able to reduce energy and gas losses to the atmosphere, because of the liquid’s property of filling voids in the material. The solid-like behavior of the non-Newtonian mixture was investigated for its capability to improve borehole confinement, since the mixture reacts like a solid when under shear stress. The results were compared to those from sand and air stemming applications, configured in different arrangements. It was concluded that the non-Newtonian mixture yielded high results due to its better confinement effectiveness, a reduction of air overpressure, and an increase of the strain propagation and ground vibration throughout the rock."

Jan 1, 2016

By T.R. Stacey

Physical testing of rock support for rockbursting conditions has been carried out for over 40 years. A review of this testing shows that it has been mostly component based, rather than actually testing support systems. Further, it is concluded that none of the testing is truly representative of rockburst loading in a similitude sense. Similitude conditions are not achievable, mainly because the real conditions in a rockburst event, such as seismic source location and magnitude, wave frequencies, amplitudes, and interactions, are not all known. Because such information is not available, and because the results of all testing carried out to date have not been able to define, for support design purposes, the capacity of support systems, ongoing physical testing of rockburst support systems is essential. It is essential that the test should simulate, or actually take place in, a supported rock excavation. A rock support system is a combination of individual support components that work together to retain and contain the rock. In doing this, the components are subjected to loading by the rock and to interactive loading between one component and another. It is necessary to prove the capacity of such rockburst support systems by subjecting them to severe loading, as in direct blasting. The direct blasting approach, pioneered more than 40 years ago, probably still provides the greatest validity as a significant test of rockburst support capabilities, even though it does not simulate a rockburst. Direct blast testing of rockburst support systems in a surface environment, such as in a quarry or on exposed rock cutting surfaces, could represent a practical development of the approach, facilitating the execution and monitoring of tests.

Jan 1, 2012

Australian underground coal mines predominately use the longwall method for coal extraction. In longwall mining at least two parallel roadways known as gateroads are mined to delineate the sides of the longwall block, a longwall installation face is then driven connecting the gateroads to enable the longwall mining equipment to be installed. Roadway development should ideally be ahead of the longwall so that the longwall equipment can be installed into the newly developed panel with minimal delay to coal production. A discrete event model of roadway development can help assess how a particular configuration may perform with high levels of variability and uncertainty in operations. One of the major delays associated with roadway development is caused by the shuttle car due to its cyclic stop-start nature. Shuttle car travelling paths and machine interactions are normally constraint by the mine?s roadway layout and mine safety issues. This paper presents simulations of shuttle car route options which can be considered at the design stage to minimize the cycle time of a shuttle car as part of a general roadway development simulation model developed using 3D Flexsim.

Feb 23, 2014

By K Ellis, B Lumsden

A full-scale statistically-based on/off plant trial of a new flotation conditioning technology designed to improve fine mineral recovery was undertaken to determine whether the recovery of selected fine sulfide minerals can be increased. The technology is selective for certain sulfide minerals only, including chalcopyrite and sphalerite. The technology has been shown to selectively aggregate the fine chalcopyrite and sphalerite minerals giving increased flotation recovery. The plant trials have shown an increase in the mineral recovery, without decreasing selectivity. Size by size recovery shows a significant increase in the fine (

Jan 1, 2005

By Alex Chapman, Cam Thomas, Bryan Karney

"During the early summer of 1989, Ontario Hydro removed a concrete portion of the North Channel Dam at Crystal Falls Generating Station by blasting and excavating in marine conditions. Because of the severity of underwater blasting and because the site was in close proximity to the replacement dam, there was concern that hydraulic shock waves generated by the detonation could damage either the new dam or its control structures. This paper examines the data associated with the hydraulic shock waves generated by underwater blasting, and studies the effectiveness of an air curtain in reducing the peak pressures. In previous trials using the air curtain technique, a rule-of-thumb factor was used to estimate that only 10% of the original pressure pulse would propagate across the air curtain. However, this value had little basis in theory. A theoretical formulation of the problem by Karney in 1989 indicated a provisional value of 0.18 for this factor, but was heavily dependent on confirmation from in-field testing. Data provided by Ontario Hydro from an actual blasting procedure indicate that a more conservative value of 0.32 may be more appropriate. Thus.although the air curtain did provide considerable reduction of peak pressures, the data at Crystal Falls indicates its performance was below the anticipated level. However, due to problems with the instrumentation and some inconsistencies in the resulting data. it is recommended that this value be further refined as additional data become available."

Jan 1, 1992

By D. R. Murray

A four-year study was carried out to determine the ability of coniferous trees to aid in the reclamation of uranium tailings at Elliot Lake. Five species were planted: white cedar, white spruce, jack pine, scotch pine and red pine. More than 570 bare-root, two-year-old seedlings were planted on bare tailings and in areas of established grasses. A further division was made between areas of coarse and fine tailings. Over-all survival and growth of the trees has been far below expectations based on previous experience with several varieties of grasses. The criteria for assessment have been per cent survival and yearly growth as determined by plant height. Pine was superior, with 68% survival when planted in bare coarse tailings, 45% for vegetated coarse tailings and 34% for vegetated fine tailings. Cedar had the worst survival rates at 49%, 14% and 7% respectively. No species survived on bare fine tailings. The survival and growth of the coniferous trees have been related to species, environmental conditions and tailings properties.

Jan 1, 1978

By Richard Short

Shallow rainfall-induced landslides in residual and colluvial hillslopes and steep embankments are a common occurrence in many settings [1, 2, 3]. While occasionally posing a threat to property and life-safety, they more often present an ongoing maintenance problem and can lead to the initiation of larger failures. Typically, these slides consist of 2 to 4-foot thick translational movements of silty and clayey soils down slope through the reduction of strength from increases in pore water pressures. Direct surficial infiltration and indirect groundwater seepage are the normative triggers for failure. In the residential community of Blackhawk, California, located east of the San Francisco Bay, these types of landslides are a common occurrence (Figure 1). However, shallow landslides have also been a repetitive and constant problem along many state highways where steep embankments have been constructed in close proximity to busy thoroughfares. Given the real threat to property values in residential and commercial settings and the constant maintenance problem posed to lifeline structures such as utilities, roadways, and pipelines, new methods to deal with these landslides are needed.

Jan 1, 2007