Search Documents

By T. T. Chiweshe, L. S. Mokhahlane, M. Welman-Purchase

This study examined an alternative technique of extracting tungsten from wolframite ore using a fusion method with ammonium phosphate salt. Current techniques use alkali salts to decompose tungsten ores and use various purification methods to produce ammonium paratungstate, which is a key intermediate precursor in the extraction of tungsten. In this study, a two-step extraction process, which involves thermal decomposition of the ore using fusion and a separation stage, is examined. The novelty of this technique is the ability to completely decompose wolframite ore and form an unstable tungsten oxide phosphate (WO2(PO3)2) compound. The instability of WO2(PO3)2 in deionized water enables selective isolation of tungsten as insoluble precipitates of WO3 and WO2. The decomposition reaction of WO2(PO3)2 is influenced by the presence of oxygen and determined to be first order under ambient conditions. Scanning electron micrographs and X-ray diffraction analysis showed above 80% of the tungsten precipitated compared with the amount that remained in the filtrate solution.

Jul 10, 2024

By J Sigda, T Jones, D Staggs, J Ewing, C Cheng, J Pickens, S Paulka

Mine-derived solutes from Energy Resources of Australia’s (ERA’s) Ranger uranium mine have been closely monitored for decades. Ranger is surrounded by the Northern Territory’s Kakadu National Park and is upstream of Ramsar convention wetlands. Modelling of groundwater flow and solute egress from mine wastes to surface waters has helped ERA successfully assess closure options and secure intermediate regulatory approvals during the site closure process. Potential environmental impacts were assessed using groundwater modelling in support of three ERA applications involving disposal of tailings-derived mine waste. Model results were an important part of the basis for obtaining regulatory approval. Three case studies are presented describing the three applications and how the groundwater modelling supported approval of the applications. For case study #1, INTERA supported ERA in addressing stakeholder concerns in 2017 regarding two aspects of tailings deposition in Pit 3. The first was the potential for flow of tailings fluid into the surrounding formations during tailings deposition. The second was the difference in post-closure magnesium (Mg) loading to surface water for two tailings deposition scenarios. INTERA developed a two-dimensional (2D) model that showed excess tailings pore pressures would not cause outflow and solute egress from the pit during deposition. INTERA’s three-dimensional (3D) models demonstrated that post-closure Mg loading to creeks for both tailings scenarios differed marginally and would be a small fraction of natural creek Mg loads. The modelling results helped avoid delays in completing tailings deposition driven by stakeholders’ environmental concerns. Case study #2 consisted of supporting ERA’s 2019 request for approval to change the tailings deposition method and final tailings level in Pit 3. INTERA’s model results for the permitted and proposed deposition methods showed minimal differences in post-closure Mg loading to creeks. The model results helped ERA obtain the needed approval for the tailings deposition method and water and tailings levels in Pit 3. For case study #3, INTERA modelled the comparative impacts from leaving the entire contaminant plume from the temporary tailings storage facility (TSF) in situ or excavating a portion of the contaminated material from beneath the TSF floor and placing it in Pit 3. The modelling results supported an approved TSF contaminated material application important for ERA to stay on schedule and minimise both closure costs and environmental impacts.

Jul 1, 2021

By Gibson J.

Written discussion contributions to the paper presented at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 12th February 1916, with Mr. T.Y. Greener, President, in the chair, comprise comments by Kilpatrick W.M., Routledge W.H., Watson J. and Smith W., along with the author's reply. Also briefly noted are the demonstration of two pieces of equipment, an incline chock and a cage arrestor

Dec 1, 1916

By Robert A. Jankowski, Charles A. Babbitt, Natesa I. Jayaraman

Today, approximately 31% of underground coal mining operations have designated occupations or areas with more stringent (below 2.0 mg/m3) respirable dust standards in place. Many U.S. coal mines have been able to maintain compliance with very low dust levels, and the Bureau of Mines, in an effort to identify those factors contributing to low dust levels, completed a survey of twelve continuous miner sections which were able to maintain their dust levels at or below 0.5 mg/m3. The quantity and quality of face ventilation appeared to be the most important factor in controlling dust exposure. The results directed Bureau research towards identifying improved face ventilation techniques for reducing quartz dust levels on continuous mining operations. This research has involved the evaluation of a half-curtain face ventilation technique which reduces the cross-sectional area of the entry, thus increasing the air velocity over the operator. The Bureau has also conducted extensive laboratory studies to compare tubing versus brattice, including an evaluation of both systems in a crosscut turn. In an effort to improve ventilation and reduce dust exposures of roof bolter operators working downwind of the continuous mining machine, the Bureau has evaluated two novel face ventilation systems. The first system consists of a fan discharge tubing technique which routes dusty air away from the return entry being bolted. In a technique similar to the fan/tubing concept, exhaust air from the upwind continuous miner face can be scrubbed using a dust collector to capture a portion of the dusty air, clean it, and supply it to the bolter operators as a split of clean intake air. A better understanding of face ventilation techniques should lead to solutions to the problem of more stringent dust standards due to quartz.

Jan 1, 1989

By C. A. Allen

In presenting a summary of the uses of fine and pulverized coal the writer has borne in mind that we are not trying to determine what a combustion engineer should know but we are only trying to find out in what ways the consumption of slack can be stimulated. First discussing the use of powdered coal it can be stated that it has passed the first experimental stage but is still capable of much development and improvement. It has already found successful application in stationary and locomotive boilers, cement kilns, calcining furnaces, reverberatory smelting furnaces and many other types of furnaces, such as open hearth furnaces and annealing furnaces. For stationary boilers it seems to have been thoroughly demonstrated that powdered coal is more efficient than stoker installations. Over-all efficiences of boiler and furnace in stoker installations of the best type run from 70 to 76 per cent; whereas the efficiency of powdered coal installations averages slightly over 80 per cent. However, due to the increased cost of pulverized coal, the increased efficiency of these installations over stokers, from a money stand-point, will not be more than 1 or 2 per cent. The fusing of the ash in pulverized coal installations has given some trouble but apparently is easily overcome, on the other hand the fine ash, which is carried along with the draft, causes trouble both in the boiler and by settling on surrounding buildings or ground. Offsetting the disadvantages the great advantages of pulverized coal for stationary boilers seem to be: First-the ease with which a change in the load on the boiler can be taken care of. Second-when a boiler is cut out for a short period the "stand-by" losses are much less and, Third-a much poorer grade of fuel can be used. In many cases where pulverized coal has been used it has replaced slack coal which is of little advantage to the coal operator. However,, in other places it has replaced gas or oil and this is where the coal man is interested. Pulverized coal has the same advantages as the liquid or gas fuel but the question as to which is preferable depends on their relative cost at the point of use. In small stationary boilers where stokers are not used, very frequently the larger sizes of coal are, and it would be an advantage to the coal industry for them to be converted so as to burn pulverized coal, but so far there are only records of a few of such small installations having been a success and there is apparently room for a large amount of experimentation. In furnaces, such as smelting and assaying furnaces, annealing furnaces, etc., slack coal is not used and where pulverized coal has been installed it nearly always replaces fuel oil or gas. Just how much increased consumtion of coal can be made by pulverizing it for use in furnaces of this type can not be determined but it seems worthy of investigation. For locomotive boilers pulverized coal has found some application up to date but where it was being used in the United States it was stopped when we entered the war. In Brazil, however, the Central Railway has been using pulverized coal for locomotives with excellent results. If it could be possible to apply it to locomotive use where fuel oil is now used, or the larger sizes of coal, it would certainly make a big difference in the slack situation. Now as to the uses of slack coal without pulverizing. The writer's investigations lead him to believe that the greatest opportunities in this direction are in the line of increasing its use by apartment houses and small home owners. In fact in looking into the subject I found that a number of men in Salt Lake City are using run of mine coal in the usual type of house furnaces, some of them by separating the fines and wetting them down before feeding to the furnace claim they get no loss whatever through the grate. However, for best results with fine coal different types of furnaces must be installed and for apartment houses it would seem necessary to have either a small automatic stoker or else spray the fine coal in with an air blast from

Jan 1, 1922

By Bo R. Arvidson

High-energy product permanent-magnet materials of rare-earth cobalt alloys are being used in applications where space or weight are at a premium cost. New applications like friction-free bearings are also made possible. However, such magnet materials have not been commercially used in magnetic separators until now due to the high cost for the overall magnetic flux generation relative to commonly used ceramic magnets or AlNiCo magnets. The design of the new high-intensity permanent- magnet roll separator (PERMROLL) takes advantage of the unique properties of rare-earth cobalt magnets rather than just substituting for conventional magnet materials now in use for magnetic separators. Hence, the new generation of high-intensity magnetic-roll separators has some unusual characteristics that make known magnetic separation applications more economically attractive, and even expands the magnetic separation technology area to include applications for which no other feasible methods are presently known.

Jan 1, 1983

By Wm. E. Milligan

LEAD stocks at the beginning of 1943 were comfortable when compared with those of other base metals such as copper, zinc and tin. This situation was early recognized by W.P.B. and other Governmental agencies and every effort was made to encourage the substitution of lead for these latter metals in all essential uses. Despite this apparently healthy condition, lead was not denied participation in the various measures inaugurated by the Government to relieve metal shortages. Thus in the Mexican trade agreement, effective Jan. 20, the tariff on two important classes of lead importss was halved. Similarly, in the setting up of B quota premiums, a B base was allotted to lead, with all pro¬duction above this figure receiving an additional payment of 2.75c. per lb., or a total payment of 11.75c. per lb. At about the same time it was announced that all quota transactions would be based upon the lead content as shown by the smelter settlement sheets. This basis was 86 percent of the lead content for all ores shipped to custom milling plants and 95 per cent for ores and concentrates shipped to custom smelting plants. The importance of this action can be appreciated when in the Coeur d'Alene it was estimated as equivalent to a 5 per cent increase compared to the previous base.

Jan 1, 1944

By T. B. Linde

The Morenci In-pit Crusher and Conveyor System has been designed with safe production and cost savings in mind. Large open pit mines around the world have been installing semi-mobile crushers and linking them with a pit conveyor system to lower unit cost. At Morenci two 60/89 in. gyratory crushers are incorporated into the semi-mobile crushing plants. The ore is reduced to -8 in. and transported out of the mine on a 60 in. steel cable belt. This paper includes an overview of the Morenci In-pit Crusher and Conveyor System from the drawing board to open pit installation and finally a discussion on operating and repair considerations.

Jan 1, 1990

By J. B. Wagstaff

The raceway in front of the tuyere of the blast furnace has been studied quantitatively and a correlation obtained for the penetrastudiedtion of the blast. Some evidence is presented for the height and width of the raceway which suggests that all the raceways of a ffurnace overlap. The size of the coke in this zone has been measfurnaceoverlap.ured photographically during normal operation and results are given for the various areas. IN an earlier paper,' it was shown that a raceway exists opposite each tuyere of a blast furnace. This raceway is formed by the jet effect of the air emerging from the tuyere and consists essentially of a turbulence in which coke particles are recir-culated at high speed. Its presence was deduced originally from observations on movies taken with a high-speed camera through the tuyeres of various furnaces and was confirmed by experiments made on a model. In the model described,' this raceway was shown as operating in a vertical plane only, although there was a suggestion in the motion-picture film exhibited at that time that the raceway was three dimensional, unless artificially restricted. There was also some doubt then about the factors influencing its size. This paper describes the next steps in the investigation. Since the size of the raceway is obviously of importance in the operation of the furnace, it seemed worth while to study the subject more carefully. It is probably in this region that about half the coke in the furnace is consumed, so that the movement of the stock column may well be controlled by raceway behavior. Furthermore, there is some evidence to suggest that the coke is packed densely in the center of the furnace to form the "dead man" and more loosely above the raceway. It is therefore probable that the bulk of the gases passing up the stack flow from the top surface of this raceway. Clearly then, a knowledge of this critical zone is of interest to the blast furnace operator, and the first half of this report is devoted to a quantitative discussion of the subject. A further topic of interest among operators is the degree of breakdown of coke in the furnace, with which is inseparably linked the importance of a strong coke. Indeed, the whole question of the optimum size and type of coke may be as dependent on the condition of the coke in the bottom of the blast furnace as at the top. Attempts have been made from time to time to obtain samples of coke from the tuyeres and other furnace openings but they all suffer from the fact that the coke is filled to a varying degree with metal and slag and is probably broken up by the very act of taking the sample. It has proved difficult to make any reliable studies of coke size by these methods. However, it did seem possible to use the highspeed movies mentioned earlier1 to estimate the size of the coke. These movies provide an accurate record of individual coke particles so that, in theory at least, it should be possible to measure the size of the particles one by one and to obtain, for the first time, information on the coke being blown around the raceway under actual operating conditions while the furnace is performing normally. Such a study has been made and is discussed in the second half of this paper. The results obtained enabled the blast furnace data to be correlated with the model results given in the first half. Raceway Size In order to make a quantitative study of the size of the raceway it was necessary to devise some apparatus of laboratory scale, which could be handled quickly and easily. This focused attention on models, which in turn means that the laws of similarity governing this particular process must be ascertained. Method of Procedure: Since the work was to be carried out on a smaller scale than the blast furnace, the linear dimensions of the model became unimportant provided that the scale was known; it is only important to insure that the container does not affect the raceway being observed. The studies therefore were carried out in a glass-sided box, 11 in. high x 7 in. wide x 3 in. deep, using air jets ranging

Jan 1, 1954

By W. Petruk

Mineralogical studies and concentration tests were conducted on samples from an oolitic iron deposit from the Peace River district in Alberta to determine what concentrate grades and metal recoveries could be obtained. The samples assayed 32 to 37 wt. % Fe, and consisted of goethite, nontronite, ferruginous opal, siderite , quartz, amorphous phosphate and illite . Flotation with fatty acids yielded the best over-all results. A flotation concentrate from a composite sample of the iron horizon assayed, by weight, 43.0% Fe, 12.3% SiO2 , 1.9% CaD, 0.9% MgO, 4.5% Al2O3 and 2.0% P2O5 and lost 17.2% on ignition, for an iron recovery of 48.8% and a silica rejection of 80%. When heated to drive off the water, the concentrate assayed 52 w t. % Fe and 14. 8% w t. % SiO2

Jan 1, 1977

Jan 1, 1926

By D. A. Koss, R. O. Gordon

Changes in the ultrasonic attenuation in steel specimens have been observed during tensile tests. Samples of AISI 1020, 1045, and 1095 steel quenched and tempered to a spheroidized condition have been used. Both attenuation and microstrain measurements fail to reveal preyield dislocation motion in the as-tempered specimens. Upon reapplication of the load to samples in the strain-aged condition there is a large preyield attenuation increase but no observable micvostrain up to 90 pct of the flow stress. These and other observed changes can be related to changes in the free disloca-tion density and the average dislocation segment length. The results show that the increase inflow stress in the strain-aged condition is caused by increased fric-tional stresses rather than by dislocation pinning. Strain aging is found to proceed through three distinct stages. The second of these follows the t2,3 law and is characterized by an activation energy of 20 kcal per mole. RECENT years have seen substantial progress in the understanding of the sharp yield-point phenomenon in metals; the influence of solute atom pinning of dislocations, of dislocation multiplication, and of the stress dependence of dislocation velocity on the stress-strain curve has been investigated. Evaluation of the relative importance of these factors in the various metals and alloys is not complete, however, because observation of the stress-strain curve alone is not sufficient to determine the yield mechanism. In the experimental study of the sharp yield point it would be desirable to be able to directly observe the dislocations in a bulk specimen. Ideally, the observations should be made during deformation because of the rapidity of recovery processes in lightly strained metals. While direct observation of dislocations under these conditions is not possible, certain physical properties sensitive to the dislocation structure can be observed while a test specimen is undergoing deformation. Of these properties, one of the most useful is the ultrasonic attenuation. The total observed attenuation, a, is due to a number of causes: acoustic diffraction, scattering by inhomogeneities in the structure, heat flow, magnetostriction, and dislocation damping. Satisfactory measurements of the absolute a are difficult to make because all of these factors cannot be evaluated in any given specimen, but changes in a due to changes in the dislocation contribution alone can be reliably observed by appropriate technique. Because dislocation damping is sensitive to small concentrations of long, free dislocation segments, observation of acoustic attenuation due to dislocations is particularly useful in the study of the early stages of plastic deformation. In the experiments to be described, acoustic-attenuation measurements have been made on steel samples as these were pulled through their yield in tension. While many details of dislocation-damping phenomena in the bee metals remain obscure, the main characteristics of this type of internal friction are established. At low strain amplitudes and at frequencies well below that of dislocation resonance (the conditions of these experiments) the dislocation contribution to a is given by1 where A is the density of freely oscillating dislocation segments, L is the average segment length, B is the damping constant for a moving dislocation, w is the frequency, O is an orientation factor, C is the dislocation line tension, and t is a numerical factor relating average segment length to the distribution of lengths. Because of its fourth-power dependence on L, a is highly sensitive to changes in dislocation free segment length such as might arise from unpinning, recovery, jog formation, or dislocation intersection. The above equation is not valid near the resonant frequency of dislocations, but the segment length in steel is believed to be much too short to cause over-damped resonance near 10 Mc; this will be discussed later. In the present experiments plastic-strain measurements with a sensitivity of 2 x 10-5 were also made during the early stages of loading in order to detect preyield strain. The general plan of the experiments is to observe

Jan 1, 1967

By D Connelly

Quartz deposits are common in nature but the presence of quartz suitable for yielding high purity quartz is exceedingly rare. This paper describes a test work study on producing high purity quartz (HPQ) product to meet the tight product specifications of greater than 99.97per cent, including four and even five nines, for uses including, lighting and fibre optics and modern-day high efficiency solar panels. Due to demand in renewable energy applications the market for high purity silica solar panels known for their increasing efficiency and durability is rapidly growing. Demand continues to rise for the use of high purity quartz in semiconductors, electronics, imaging and sensor markets. Microelectronic components are created by chemically fabricating wafers of semiconductors such as silicon to obtain the desired transport of electrical charge and control of the current. The production of silicon metal from high purity quartz has been designated a Strategic Mineral by the European Commission and by the US Department of Justice due to the growing significance of this metal in various industries. The subsequent processing of quartz is the key step to adding value and aiding technological advances. Overall, the high purity quartz market is a highly secretive, specialised market with increasing opportunities for stakeholders. The attempt to produce HPQ in this work was carried out using an Australian quartz ore following a typical HPQ process flow sheet. The unit processes included primary crushing, scrubbing, magnetic separation, flotation, acid leaching followed by hot chlorination. The results indicate that grinding of quartz requires specialist equipment due to the hardness and extreme abrasiveness of the ore leading to additional iron contamination in the ground ore. The critical impurities were aluminium, iron, sodium, potassium, lithium, titanium, zircon, calcium and magnesium. The chemical refining was found effective. The hot chlorination process needed to be done at 1200°C in a chlorine – hydrogen chloride gas atmosphere. The risk of any gas being released during this stage is very serious and only specialist companies should and can carry out this step. More recent studies reported many new options that appear to facilitate the production of HPQ with the requisite purities more easily, but costly equipment along with highly trained operators are required and hence unlikely to become available in standard metallurgical laboratories any time soon.

Sep 1, 2024

By Arash Khosravifar, Ali N. Ibrahim

"Large areas of Iraq are covered with collapsible soils namely gypsiferous soil which is often used as the foundation soil for structures. In particular, the Mosul Dam foundation is comprised of high contents of gypsiferous soils. Intrusion of water through the foundation soil dissolves gypsum which acts as the binding material between soil particles. This phenomenon results in the formation of collapsible soils which can cause serious damages to the dam structure. The failure of Mosul Dam, with a reservoir as large as 11 billion cubic meter of water, can be catastrophic. In the past, Mosul Dam Authorities have been remediating the soil foundation by injecting cement mortar. This method has been proved not economic; therefore, new, more efficient, methods are desperately needed.This research study focuses on finding practical methods to remediate collapsibility of gypsiferous soils by improving their geotechnical properties. This study presents remediation of collapsible gypsum-rich soil by grouting. Three types of stabilizer materials were used to make the grout; (1) sodium silicate (Na2 O3 Si) which is a well-known chemical soil stabilizer, (2) bentonite slurry, and (3) silicone oil. The purpose for using these stabilizer materials is to provide an impermeable layer (waterproofing coat) around the gypsiferous soil particles and to fill the voids that may occur in the soil as a result of gypsum dissolution when subjected to water.A series of double oedometer (collapse) tests and direct shear tests were carried out on gypsiferous soils before and after remediation by grouting. The results show that the soil compressibility decreases in the grout-treated gypsiferous soil by reducing volumetric strain. Consequently, the potential for collapsibility decreases too. It was also shown that grouting, increases the shear strength of the soil at confining stresses smaller than 250 kPa by increasing the cohesion combined with a slight reduction in the internal friction angle.INTRODUCTIONGrouting is one of the ground improvement techniques which is often used to improve the loose foundation soils. Bruce (2003) provides step-by-step procedures on using grouting techniques for sealing dams and other water reservoirs. Grouting can be classified as permeation grouting, compaction grouting or hydraulic fracturing. Permeation grouting is an effective way to send the grout into the ground without disturbing the soil structure, i.e. free flow of grout into the soil voids where grouting is accomplished by injection of a fluid-like material that is capable of forming a gel and binding the soil particles together. Grout materials may be solution grouts or suspension grouts. The permeation grouting technique is generally used to minimize ground permeability and to control ground water flow, but it can also be used to strengthen and harden the ground (Raman et al., 2012)."

Jan 1, 2017

By Earle Bagley

In late 1971, the Sun Company, then known as Sun Oil Company, acquired a large surface mineable federal coal lease with the thought that those coal measures within its boundaries would provide a future feedstock of either coal or coal liquification. Our Cordero lease was one of the last Federal coal leases let before the recent decade long leasing moratorium. Because of the tremendous demand for compliance steam coal for the electric power industry, a decision was made to develop the property to serve that market. In 1974, Sunoco Energy Development Company (SUNEDCO), the non- oil and gas energy unit of the Sun Company, began engineering studies for development of the lease. The mine was originally designed at a 12.0 million ton per year capacity. The Cordero Mining Company was formed to mine and operate the property. Construction of the facilities adjacent to the lease began in January 1975. Due to the Sierra Club versus Department of Interior Secretary L. B. Morton suit, work within the lease was delayed until mid-1976 when pre-stripping of the overburden began.

Jan 1, 1982

By Dale Preece, Joergen Pilz, Zavis Zavodni

An overland conveyor was constructed at a surface coal mine to reduce the truck haul distance and make the operation more efficient. An important element in this system is a truck dump facility to transfer coal from truck to conveyor. Mechanically stabilized earth retaining walls were employed to accommodate the coal processing equipment, including the crusher, in this facility. These retaining walls are close enough to the pits being mined that blasting induced vibrations must be considered in analyses of the wall structural stability.

Jan 1, 2010

By R Bezuidenhout, J K. Claflin, S R. La Brooy, G M. Wardell-Johnson, A M. Claflin

Best practice gold (Au) recovery is not an accident. It is the result of proper operation of the adsorption circuit using good quality activated carbon. A conventional carbon ‘regeneration’ kiln cannot process carbon fouled with floatation chemicals and achieve best practice gold recovery. A high temperature, controlled atmosphere carbon ‘reactivation’ kiln is required. Carbon circuit design allows for low quality carbon by increasing the carbon advance rate, carbon inventory and setting an easily achieved and commercially prudent solution tails target of typically 0.02 ppm Au. These design criteria are important to ensure the commercial success of the gold operation in the first instance. Most carbon ‘regeneration’ kilns will produce carbon of sufficient quality to achieve a 0.02 ppm Au solution tail in the absence of flotation reagents.Best practice recovery is considered less than 0.005 ppm Au in solution reporting to tails. If the carbon is heavily fouled, as it will be if used for flotation leach circuits, then a conventional carbon ‘regeneration’ kiln cannot achieve world’s best practice recovery no matter how much carbon is advanced. World’s best practice gold recovery requires a carbon ‘reactivation’ kiln and the whole of the carbon circuit operated optimally.The competing reactions occurring in a carbon ‘reactivation’ kiln are presented and discussed in terms of kiln design and operation. New industrial and laboratory findings are presented to fill gaps in the body of knowledge and identify that a large reduction in residence time at temperature will not significantly impair reactivation, but can significantly reduce the size and cost of the kiln or permit significantly increased carbon throughput.The carbon circuit performance is modelled in terms of gold adsorption, as a function of carbon reactivation using ‘simulation of carbon-in-leach/carbon-in-pulp circuits’ (SIMCIL). An optimum carbon advance rate is identified as a function of optimum carbon ‘reactivation’ kiln operation to achieve 0.005 ppm Au in the tails solution. A conventional carbon ‘regeneration’ kiln is compared to a state-of-the-art carbon ‘reactivation’ kiln in terms of reactivation performance and gold recovery.CITATION:Claflin, J K, La Brooy, S R, Wardell-Johnson, G M, Bezuidenhout, R and Claflin, A M, 2017. Optimising carbon reactivation kiln operation, in Proceedings MetPlant 2017, pp 346–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By T. H. Etsell, P. Kerr, Qi Liu

"The objective of this investigation was to study the reaction mechanisms during the reduction of iron oxides in the presence of calcium chloride and carbon black as a simplified iron segregation process. The gas phase was analyzed by mass spectroscopy and the solid reaction products were analyzed by scanning electron microscopy. Mass spectroscopy, combined with thermogravimetric analysis and differential scanning calorimetry, revealed the presence of several gases at elevated temperatures over time, and the scanning electron microscope in combination with energy dispersive X-ray analysis illustrated the growth of a metallic iron phase on or near the carbon substrate. The results correlated well with similar copper and nickel segregation processes, but also introduced new insights that challenge the simplicity of the current models. The formation and transport of gaseous iron species to the carbon substrate in the presence of steam and hydrogen were evident during the reduction process that was studied; however, there is more happening at a mineralogical level, based on evidence of a liquid phase resulting in substantial growth due to an apparent fluxing effect created by the calcium chloride.These results help to better explain the chemical reactions and, in turn, the thermodynamics and kinetics of iron segregation processes related to the beneficiation of low grade complex iron ores. The results are also applicable to the production of metallic iron and concentrated titanium dioxide from ilmenite ores. The benefit of this process is that it allows ores in which the iron minerals are intimately associated with gangue minerals to be processed in circumstances where conventional mineral processing techniques are unsuitable or incapable of upgrading the material."

Jan 1, 2016

By C. J. Van Niekerk

The study comprised of the investigation into the sensitization characteristics of AISI 409 titanium stabilized ferritic stainless steel during low heat input welding. AISI 409 is a fully ferritic stainless steel used in catalytic converters and tubing for automotive exhaust systems due to the supposition that sensitization does not occur during low heat input welding. Two plates of 2 and 4 mm were tested for sensitization during low heat input welding. The study confirmed that chromium carbide (M23C6) precipitation occurs on the grain boundaries in the heat-affected zone with consequent depletion of Cr adjacent to the grain boundaries during welding. In the 2 mm plate sensitization occurred in the heat input range of 0.1 kJ/mm to above 0.25 kJ/mm and in the 4 mm plate sensitization occurred in the heat input range of 0.2 to 0.9 kJ/mm. Ti stabilization is ineffective at the heat inputs used in this investigation due to the rapid cooling rate through the temperature region where TiC precipitates. The presence of N was found to be detrimental since it consumes Ti on cooling, forming TiN, effectively lowering the amount of Ti available for TiC formation during rapid cooling after welding. Annealing for 5 minutes at 725°C does not improve the sensitization characteristics of the welded plate. There is a linear increase in grain size as heat input increases. The resistance to pitting corrosion decreases in the sensitized, welded plate in theheat-affected zone adjacent to the fusion line of welding. Keywords AISI 409 ferritic stainless steel, sensitization, grain growth, resistance to pitting corrosion, low heat input welding.

Jan 1, 2011

By Thomas C. Wilder

The concentration and activity of oxygen in liquid copper has been measured by the reversible galvanic cell: at 1100°and 1200°C for the concentration range of oxygen of 3 to 5600 ppm Measurements for approximately thirly alloys at each temperature indicate that the activity of oxygen roughly follows Henry's law, the activity coefficients of oxygen being 0.12 and 0.205 at 1100° and 1200°C, respectively. These results compare javorably with the results of seven other electrochemical and gaseous equilibrium studies on this system, the free energy of the solution reaction 1/2 O2 = O (7 at. pct in Cu, liq) being -18.10 * 0.30 kcal per gfw at 1200°C. Estimates of the standard molar free energy of formation of CupO(S) are also made. Praclicul consideration of this cell as an oxygen sensor for liquid metals is discussed briefly. SOLID mixed-oxide electrolytes which have a defect structure in the anion sublattice have recently become a very popular means by which the chemical potential of oxygen is measured at high temperatures. Since the pioneering work of Kiukkola and Wagner1 such electrolytes have been used in numerous cell studies for determining the thermodynamic properties of metallic oxides and oxy compounds, the partial pressure of oxygen in vacuum systems and other atmospheres, and the properties of oxygen dissolved in metals and alloys. The use of a solid electrolyte in a cell for a fast reliable method of oxygen determination in liquid metals would be a very important tool to the process metallurgist. In copper, for example, the oxygen content of the molten metal in the cathode furnace is a prime factor in determining the "set" or solidification profile of cast wire bars. In this investigation the activity of oxygen in liquid copper was measured by an electrochemical cell employing the electrolyte ZrO2 + 7 1/2 wt pct CaO. The cell used at 1100° and 1200°C was

Jan 1, 1967