Search Documents

By F. T. M. White, W. A. Bardswick

"The parameters of airborne minerallic particulates which create industrial dustiness, together with the physiological hazards caused by their inhalation, are reviewed. Various techniques of dust sampling are discussed and analysed, and the parameters referred to above are classified as the basis for methods of assessing the physical, chemical and mineralogical characteristics of dust-particle suspensions. The paper surveys those methods of assessment currently accepted by various statutory authorities, and reviews other methods that warrant attention and newer techniques that are being developed."

Jan 1, 1969

By Oren C. Baptist

[Several new oilfields have been developed in northwestern Wyoming during the past 10 years, production is obtained from discontinuous, permeable sands enclosed within impermeable shales. The energy to drive the oil to producing wells in supplied by gas in solution in the oil. Most of the wells had high-initial potentials, but rates of oil production have steadily declined, indicating a dissipation of the driving energy and the possibility that large volumes of oil will remain unrecovered in the reservoirs. The studies reported in this paper were undertaken to develop laboratory data of the type most likely to be needed by persons studying the susceptibility of the Newcastle sand reservoir to secondary-recovery methods.]

Jan 1, 1957

By Milton Fies

Introduction The first experiment in underground gasification of coal in the United States was conducted at Gorgas, Walker county, Alabama, under a co-operative arrangement between the U.S. Bureau of Mines and the Alabama Power Company, at the suggestion of the Power Company. The test was conducted on property of the Alabama Power Company, that owns some 19,000 acres of coal-bearing lands on which there is developed a highly mechanized mine producing some 2,500 cons of good quality steam coal per day. At the same locality ?there is a 200,000 kilowatt steam plant one of the largest in the southern portion of the United States. The Alabama Power Company owes much of its beginning in 1912 to British vision and courage. The original plans for building hydroelectric plants in Alabama, and for the construction of necessary transmission lines, were submitted to Sperling & Company, bankers of London, who agreed to underwrite certain bond issues, the proceeds of which would be used in launching the new Company on its programme. The set-up by which these funds from England were received was through an intermediary Canadian company, which the English investors desired. The Canadian company - Alabama Traction, Light and Power Company, Ltd. became owner of the securities of the Alabama Power Company and marketed its own securities through the banking house of Sperling & Company. Without assistance at this time the Alabama Power Company could not have gone ahead with its programme of expansion and the bringing together of the properties necessary for laying the foundation for a strong Company, fortified with ample power resources essential for future requirements and for dependable service to the public.

Jan 1, 1948

By K. L. Boyd

"Can the increasing tonnages of ore and waste mined today be accommodated simply by using bigger and better crushers? This paper reviews the latest primary crushing and large cone crusher designs. It highlights how—in addition to using the larger crushers now available—maximizing the utilization percentages in each stage of the rock size reduction circuit will assist in meeting the larger production requirements of existing and new mining operations. Its goal is to help consultants and operators select the optimal equipment and custom-designed items in material handling from the mine to the mill, maximizing operating hours per year.RÉSUMÉ Le recours à des concasseurs plus grands et plus performants suffit-il à gérer l’augmentation du tonnage du minerai et des déchets que l’on extrait de nos jours ? Cet article examine les tous derniers modèles de concassage primaire et de grands concasseurs à cône. Il montre que, pour satisfaire aux exigences de production plus conséquente des exploitations minières existantes et nouvelles, il est important d’optimiser les taux d’utilisation à chacune des étapes du circuit de réduction de la taille des roches, en plus d’utiliser les concasseurs plus grands actuellement disponibles. L’objectif de cet article est d’aider les sociétés d’experts-conseils et les exploitants à sélectionner le meilleur équipement ainsi que des articles fabriqués sur mesure pour la manutention de la mine au concentrateur, en optimisant les heures d’exploitation par année.INTRODUCTIONAre larger crushers the answer to meeting the demands of existing or new mining projects for increased tonnage? Boyd (2002) predicted that larger crushers for primary and fine crushing would be beneficial and contribute to the further development of mineral processing. Larger crushers for primary and fine crushing applications have since become available.The rock size reduction process from the mine to the selected milling process facility has not changed since a person first broke a rock to get at the interesting mineralization within. The rock size reduction process circuit from the mine to the mill can be summarized in four stages:• stage 1: mining (rock breakage and fragmentation);• stage 2: prescreening (scalping);• stage 3: primary crushing; and• stage 4: fine crushing (secondary, tertiary, and quaternary).Plant throughput and ore delivery schedule will form the basis for flowsheet design and equipment selection. Once the project design criteria and the mine plan have been established, the circuit’s utilization percentage (percentage of hours when the circuit is being utilized) can be optimized for each of the four stages. The mining and process departments play a key role in the selection of the final comminution circuit, and both departments should be familiar with and contribute to the design of the circuit."

Jan 1, 2017

By E. C. Sanford

A laboratory-scale batch extraction unit and operating procedure for studying the hot-water separation of bitumen from Athabasca tar sands are described. The extractor evolved from earlier units and has been in use by Syncrude Research for the past 10 years. By using a unit such as this, it is possible to study tar sand feed quality and the effects of chemicals on the hot-water extraction process, while process variables are held constant. Data are presented to demonstrate the importance of surfactants to the process and the interrelated role of inorganic bases and surfactants.

Jan 1, 1979

By Giorgio De Tomi, Ricardo Tichauer

Mineral exploration is a critical step for success in mining. However, small-scale mining often ignores exploration best practices. This paper introduces the Tichauer-DeTomi Matrix, a tool for assessment of geological uncertainty in small-scale mining. This matrix, which measures the level of compliance of exploration programs in small deposits with industry best practices, has been applied to three small mining projects in Brazil: an artisanal gold mine in the Amazon, a small-scale manganese mining venture in the Northeast, and a small manganese deposit in the Southeast. The application of the matrix resulted in indexes that reflect the actual level of maturity of the mineral exploration program in each project. Therefore, the matrix has shown potential to be an effective tool for assessment of the geological uncertainty remaining in small-scale mineral projects, as well as to identify priority exploration activities for reduction of risks associated with the geological uncertainty. As a risk assessment tool, the TichauerDeTomi Matrix may be helpful in promoting investment and sustained development in and around small mines.

By R C. Cox

The Brukunga pyrite mine was operated from 1955 to 1972 to supply feedstock for sulfuric acid production in the South Australian fertilizer industry. Iron sulfide ore, mined by Nairne Pyrite Ltd, was finely crushed and concentrated onsite with the concentrates being sent by road and rail to Port Adelaide for roasting. Waste rock was dumped at two locations on the western side of Dawesley Creek and the tailings pumped to a valley-fill storage facility on the eastern side. Production of 1.5 Mt concentrate resulted in 3.5 Mt tailings and 8 Mt waste rock. The site has been administered by the South Australian Government since August 1977 and a lime treatment plant has been operated on the site since September 1980. Environmental issues arising from these operations included: diversion of Dawesley Creek to accommodate the waste rock dumps; dumping of low-grade sulfidic ore in waste rock dumps at the angle of repose immediately adjacent to Dawesley Creek; exposed fresh sulfide mineralisation in the quarry floor; tailings storage facility dam wall constructed by upstream up-lift using tailings and waste rock; an acid water pond sited on the tailings; and pollution of natural drainage. As a result, the minesite rapidly became a source of acid drainage and potential contaminants (sulfate, Al, Fe, Mn, Cd, Zn, and Ni). Various Government bodies have been responsible for considerable effort and expenditure in reducing the flow of acid seepage and contaminants into Dawesley Creek. Presently an estimated 60 per cent of seepage from the waste rock dumps, tailings storage facility and quarry is collected and neutralised prior to discharge into the creek. Tailings have been covered with waste rock, biosolids, neutralisation sludge and soil and planted with grasses, shrubs and trees to reduce rainfall infiltration. Monitoring of water flows, water quality and riparian ecosystems is on-going. Consultants have been engaged to develop cost-effective remediation techniques and a five-member Brukunga Mine Site Remediation Board was appointed to oversee remediation of the site and liaise with the community. Construction has commenced on the diversion of Dawesley Creek, and plans are being developed for the relocation of waste rock back to the quarry benches and upgrading of the neutralisation plant. The paper examines operations, environmental monitoring, remediation, research and community involvement with respect to current best practice.

Jan 1, 2003

Approximately forty years ago, the military services began a realistic investigation of the problems involved with the replacement of high pressure gaseous systems with liquid oxygen systems. The program was temporarily discontinued because of numerous State-of-the-Art problems. Ten years later, interest in the liquid oxygen breathing concept was revived. Initial testing of this concept was completed in 1946. The ensuing years have seen the general acceptance of many cryogenic breathing systems for airborne applications. The inherent features of weight savings (approximately 70%) and space savings (approximately 80%) make it very desirable for high performance military aircraft. A typical aircraft system consists of a storage container with appropriate integrated control valving (the liquid oxygen converter), a heat exchanger, breathing regulator, and oxygen mask. Normally the liquid converter is located in the aircraft wheel well for easy access by ground crew personnel and the breathing regulator is mounted in the cockpit where the pilot can connect his oxygen mask. An aircraft system such as this will provide the pilot with eight hours of breathing oxygen after a 24 hour standby period. Early in 1960, the National Aeronautics and Space Administration sought a means of providing a cooling system for their personnel involved in fueling the rockets used in the space program. While fueling rockets N.A,S.A, personnel wore a completely enclosed butyl rubber suit and were susceptible to heat prostration. Using the concept of an aircraft system, Aro redesigned the container, heat

Jan 1, 1971

By Camilo A. Alvarez, Stephen K. Harris, Brian R. Zuckerman, Philip J. Meymand, Danielle M. Steinmetz

"The sleek new air traffic control tower at the San Francisco International Airport stands at 221 feet tall and is set to replace the existing air traffic control tower by 2016. This aluminum-clad, torch-like structure and three-story Integrated Facilities Building at the base are situated between Terminal 1 and Terminal 2 adjacent to the tarmac. Berkel & Company Contractors, Inc. and Simpson Gumpertz & Heger Inc. worked in conjunction with structural engineers from Walter P. Moore Engineers and Consultants, geotechnical engineers from URS Corporation, architects from Fentress Architects, and general contractors from Hensel Phelps Construction Company on the performance-based design of a foundation to support this critical facility, which is located in a high seismic zone and situated on the very soft soil of the San Francisco Bay margin. With the loading demands and performance criteria established and Young Bay Mud thicknesses ranging from 44 to 47 feet thick across the site, the design team employed a total of 214 24-inch diameter Auger Pressure Grouted piles, which were drilled into the underlying Franciscan Formation as deep as 148 feet below existing grade. Pile reinforcement included full-length confined cages.The piles were designed to resist Maximum Considered Earthquake axial demands as high as 1,400 kips in compression and 700 kips in tension. The performance-based pile design included verification of shear capacity under double-plastic-hinge flexural mechanisms, verification of pile ductility via non-linear moment-curvature analyses, and consideration of curvatures due to kinematic as well as inertial loading.The team implemented an extensive pile load test program including a full-scale static compressive load test on a sacrificial test pile and five non-destructive high-strain dynamic load tests, four of which were performed on indicator piles that were later used as part of the foundation system. These piles were monitored with extensive embedded instrumentation throughout their length, including strain gauges and accelerometers."

Jan 1, 2017

By John R. McWilliams

This is one of a series of reports being published by the Bureau of Mines on mining methods and costs at various mines throughout the United States. Including the Holden mine in this series is particularly appropriate at this time. The mine was operated on a low-cost, large-scale production basis to compensate for low-grade ore. Even with the best conditions and the most efficient methods, the margin of profit was small. Under the present situation of rising costs and lowering metal prices, the profit margin vanished. On June 28, 1957, the mine operations ceased; therefore, this report can review the entire life span of the mine.

Jan 1, 1958

By R. S. Dean

This report, the third of a series of annual reports of the Metallurgical Division to be released in this form, covers the fiscal year July 1, 1936, to June 30, 1937. The technological work of the division is performed by sections. Thus, an efficient organization is provided to prosecute the various problems under investigation, and a logical system is set up for presenting the material contained in this report.

Jan 1, 1937

By B. T., Colley

AS always when metallurgical operations are conducted within or close to agricultural and stock-raising regions, the question of damage due to fume and smoke presented itself when the Cerro de Pasco Copper Corporation's new smelter commenced to operate in La Oroya in 1922, For more than twenty years the Corporation had operated its old plant close to Cerro de Pasco without encountering difficulties from smoke claims, owing to the fact that it was in an open plain where more or less constant air currents carried and dissipated the smoke over large areas, affording ample dilution. But Oroya is in a deep canyon formed by four contributing valleys up and down which the smoke travels for long distances in a more or less concentrated form. Though the altitude of Oroya is more than 12,000 ft., and the surrounding country rises to much greater elevations, nevertheless there exists there a large and important stock-raising industry and also a considerable development in agriculture, consisting of the cultivation of potatoes, barley, etc.

Jan 1, 1945

By Michael MacMillan

AI is already changing how mining companies are seen, judged, and trusted. This paper discusses “reputation engineering,” a structured way to build trust in a world where AI systems summarize and evaluate everything a company says publicly. Using mining examples, emerging AI search trends, and real communication work, the paper explains why the next 12–18 months are a crucial window for action. It also provides a practical framework to help mining companies improve their visibility, accuracy, and consistency across both human and machine channels.

Feb 22, 2026

By Ehab Gomaa, K. A. El‑Nagdy

Backfilling material such as tailing (mine wastes) mixing with cement or gypsum has grown throughout the world’s underground mines. However, despite their growing popularity, the typical hydraulic and mechanical fill types utilized in many mines still exist. Deep underground mining has increased due to the lack of commercial minerals nearby. Mine wastes were considered the main part of backfilling to prevent environmental pollution, ground subsidence after mine abandonment, and mine collapse during deeper extraction phases. The cemented backfill technique is the principal technique used in underground mines, which include cement with fly ash and/or filter dust, cement with tailing material and fly ash, gypsum with fly ash, and synthetic anhydrite with fly ash and have been reviewed. It has concluded that a backfilling material must be selected based on further goals, available material near the mine site, and economic factors. This paper analyzes different backfill material mixtures to create a technique that will increase safety in underground mining conditions and foresees an appropriate formula that gives high uniaxial compressive strength. The multiple linear regression (MLR) on the collected data from the experimental works to construct the relationship between the uniaxial compressive strength (UCS) of the mixture and the components of the backfilling and the prediction formula for expected compressive strength was obtained. The results revealed that the predicted regression equation was robust and reliable to predict the (UCS) for the new components of the filling (cement (CE), filter dust (FD), water content (WC), and time (T)).

Oct 3, 2023

By E. R. Cole

This Bureau of Mines investigation was prompted by the need forr a stable anode for electrowinning metals, particularly zinc and copper, from acid solutions. The polarization behavior of Pb-Ag (1 pct Ag) anodes in H2SO4 and fluoride solutions was determined as the first step in the development of such an anode. A Luggin capillary, dc power supply, high-impedance voltmeter, and other equipment standard to an electrochemical laboratory were used in this study. It was determined that during polarization, a relatively hard, stable coating of Pb02 was formed on the surface of the lead-silver anode and the rate of formation of this coating was considerably enhanced by the presence of fluoride ions in solution. Subsequent investigations at the Bureau of Mines Rolla Research Center resulted in the development of a Pb02-coated titanium (Pb02-Ti) anode. Results of this effort were presented in Bureau of Mines Report of Investigations 8111. Additional data resulting from extensive testing of the Pb02-Ti anodes, as well as process improvements and innovations, are included in this report. The anodes were considered generally unsatisfactory for zinc electrowinning because of lower conductivity, higher oxygen overvoltages, and shorter in-cell life as compared with the Pb-Ag anodes now being used in industry. However, the PbO2-Ti anodes were used successfully to oxidize waste chromium solutions and to electrowin copper.

Jan 1, 1981

By E. G. SINCLAIR

DRILLING wildcat wells in Wyoming differs a little from methods used in any other field. Here it is always advisable to start the hole as large as is convenient in order to carry each string of pipe as far as possible, so that drilling can be continued a thousand feet deeper if necessary, as there is always sand a few hundred feet ahead that really ought to be tested. This plan may seem ambitious, but if it is adhered to, it will save a great deal of trouble before the well is completed. In making the location, one representative from the operating department and one from the geological department should work together, so that the well may be in the best possible place for obtaining oil and the most feasible place to drill for the operating department. In Wyoming nearly all wells are drilled with standard tools, as with them a better log can be kept and better time made in completing the hole. The shales of Wyoming are very hard and do not mix well in a wet hole. The shale cuts into large pieces, too large to be circulated out of the hole, and forms a mat on the rotary which soon cuts off circulation. Then if this mat cannot be jarred from the bit, the drilling string has to be pulled and the mat cut off from the bit with a pick or an axe. I have seen standard tools come out of a wet hole with 10 to 16 in. of mat on the bottom of the bit. Rotary tools have drilled wells satisfactorily in the Big Muddy field and at Billy Creek, but in the other fields the wells have been drilled much more economically with cable tools.

Jan 1, 1926

By Constantine C. Popoff

This report reviews and analyzes, by a simple analytical and logical reasoning, the conventional methods of reserve computations of mineral deposits described in various domestic and foreign publications. It brings together, formulates, and evaluates the principles underlying interpretation of exploration data; and ties such principles to the proposed classification of methods. The material is discussed in sufficient detail to allow general application.

Jan 1, 1966

By D. L. Neylan

The Bureau of Mines evaluated various methods for identifying sources of mercury vapor in excess of the threshold limit value (TLV) of 0.05 mg of mercury per cubic meter of air set by the American Council of Government and Industrial Hygienists (ACGIH) for mines and mineral processing plants. Chemical spot tests and portable devices for mercury determination were evaluated, based on information from published sources and performance in laboratory tests. Among the parameters examined were sensitivity, interferences, cost, ease of use, and other factors pertinent to field application, More than 50 methods were evaluated. The investigators found that many readily available methods are suitable for identifying sources of mercury vapor in mines and mineral processing plants. The best method appears to be one that uses a commercially available mercury test paper sensitive only to mercuric ions. For some of the more promising chemical spot tests, this report includes step-by-step instructions for field application.

Jan 1, 1983

By Paul B. Batten

Shutdown is a generic term for what may be called an Outage, Turn Around (TAR) or Overhaul etc. Running a plant shutdown well has always been key to the financial contribution of a mine. However, something important has changed. The post pandemic reality is that it is harder to retain workers and many of those near retirement just didn’t come back to work. This is creating a shortage of experienced people and a workforce that changes employers easily. We are seeing the impact of this manifested in the erosion of established maintenance and supply chain processes that now struggle to yield the plant runtime that could once be taken for granted. The scope, cost and duration of a shutdown varies widely depending on the nature of the work and the equipment being renewed. The PM of an electric shovel might require a week of downtime and cost $100,000. A gold plant may need to go down for 3 days when its time to change mill liners and cost $500,000. A turnaround in a refinery can take more than a month and cost multi millions. Despite the huge differences.

Jan 1, 2023

By Rolf A. Knopp

This paper discusses how design differences in FLP diesel equipment in underground coal mines came about. "Design standards" tend to create differences between countries while fostering uniformity among products of competing manufacturers. "Performance requirements," on the other hand, tend to eliminate differences between countries while encouraging competitive development of better products. Examples of regulations from the U.S., Canada. Great Britain. Australia. South Africa, etc., are used to illustrate differences in the design and certification of diesel equipment for underground coal mines.

Jan 1, 1978