Search Documents

By Timothy C. Siegel, Paul J. Axtell

The Missouri Department of Transportation (MoDOT) recently replaced the Hurricane Deck Bridge that carries Highway 5 traffic across the Osage Arm of the Lake of the Ozarks in Camden County, Missouri. The former bridge was constructed in the 1920's and was supported on pneumatic caissons bearing on dolostone bedrock. The replacement structure is founded on drilled shafts socketed into the bedrock. During the design phase of this bid-build project, a baseline design was developed and Alternative Technical Concepts (ATC's) were allowed from approved contractors. Those ATC's were confidential and not shared between teams. Either the baseline design or the approved ATC design could be bid by the respective contractors. The baseline design included re-use of the 90-year old caisson foundations. Accordingly, an extensive evaluation of the caissons and underlying bedrock were conducted by coring, laboratory testing, acoustic tele-viewer (ATV), and cross-hole sonic logging (CSL) methods. The results of the investigation indicated the caissons were in excellent condition and suitable for re-use. However, a more cost-effective ATC was submitted, awarded, and constructed that did not re-use the existing caisson foundations but rather reduced the span lengths, increased the number of piers in the water, and supported those piers on drilled shafts. Interestingly, the difference in low bid price between the awarded ATC and the baseline design was less than one percent of the construction cost. This paper describes the multiple foundation designs that were necessary for this interesting project. The various foundation evaluations include the existing pneumatic caissons, large-diameter open-ended pipe piles to support the baseline design, and the design of rock-socketed drilled shafts that were successfully constructed in 2012.

Jan 1, 2017

By E. H. W. Hornbrook, P. W. B. Friske

Paper presented at the 28th International Geological Congress, Washington DC, July 1989 (International geochemical mapping sessions). The objective of the programme is to establish and maintain a nationally consistent geochemical drainage database. Towards this end systematic surveys have been conducted since 1973. To date more than 200 surveys have been completed to the required standards, representing 180 000 sites and covering about 2 100 000 km2 throughout Canada

Jun 13, 1905

By Jean-Pierre Birat, Ana-Maria Iosif, Denis Ablitzer, Olivier Mirgaux

"Integrating environmental considerations into the product traditional process design is now the major challenge for steel industry. Life Cycle Assessment (LCA) is nowadays considered as an appropriate method for assessing environmental impact and selecting new technologies to reduce CO2 emissions for steel industry.In this paper we propose a new methodological concept which combines LCA thinking with process simulation software in order to carry out the life cycle inventory of classical steelmaking process.Using Aspen PlusTM software, a physicochemical model has been developed for the integrated steelmaking route. This model gives the possibility to carry out life cycle inventories for different operational practices in order to optimise the use of energy, to calculate CO2 and other emissions and to control the mass and the heat balances of processes.It is also shown that such approach can be used to design and assess new technologies for steelmaking without large industrial application.IntroductionDuring recent years, it was recognised that CO2 emissions are the major factor of the global warming effect. In order to meet Kyoto requirements, the steel industry is embracing the challenge of sustainable development by improving its competitiveness and economic success while reducing its environmental impacts. Integrating environmental considerations into the traditional product design process, for powerful eco-efficiency, is now one of the major priorities for steelmakers.The European Steel Industry has measured up to this challenge by creating ULCOS (Ultra Low CO2 Steelmaking) consortium that has taken up the mission to develop breakthrough steelmaking process with the potential to reduce CO2 emissions (Eurofer, 2005). In order to develop technologies to reduce emissions, it is necessary to assess the environmental impact of the classical steelmaking route (coke plant, sinter plant, blast furnace, basic oxygen furnace, continuous casting and hot rolling)."

Jan 1, 2009

THIS bulletin presents all analytical and lest methods regularly used by Bureau of Mines laboratories for characterizing coal and coke. To provide better service to coal producers and consumers, the scope of this bulletin has been expanded to include important test methods used to evaluate coal properties for commercial processing. The methods described will prove valuable to all persons interested in analyzing and testing coal and coke.

Jan 1, 1967

By Charles V. Jude

This U.S. Bureau of Mines report presents a review and evaluation of existing and new backfilling materials and methods for their applicability to the problem of gate road stress reduction in deep retreat longwall coal mines. Candidate backfill materials include pulverized coal combustion fly ash, flue gas desulfurization, and fluidized bed combustion by-products from coal-fired electric power generation plants. Properties of both backfill and its component materials are presented, with particular emphasis on the unconfined compressive strength and elastic modulus of backfill mixtures. Hydraulic mix designs discussed in this report include high-water content slurry and low-water content paste fills. Three gate road stress-transfer-modification concepts are proposed to reduce abutment stresses in gate road systems. The first concept, packwalling, involves packwall construction behind the headgate shield inby the face and adjacent to the headgate pillars. The second concept, gob-filling, involves infilling a strip of gob inset from and parallel to the headgate using paste injection methods patterned after a technology recently developed in Europe. In the third concept, entry-filling, slurry fill methods are used to fill abandoned gate roads and crosscut entries inby the face.

Jan 1, 1995

AGENDA ? Company Overview ? Industry Direction ? Technology to support maintenance ? data access, connectivity, process historian, downtime & production reporting. ? Case Studies Company Overview Corporate Offices Client Base ?16 consecutive years of growth & profitability ?#39 of Top 50 Control Companies (Worldwide) ?470 employees ?TSX: MTK Industry Direction Improved visibility into the business so they can: ? Reduce cost through better understanding of where costs are being incurred and making timely decisions. ? Optimize operations while leveraging existing assets. ? Have a single version of the ?truth? ? Deliver reliably to stakeholders on the demand for increased accountability (safety, environmental, regulatory performance etc?). ? Respond quicker to market conditions in order to out perform the competition ? Best in Class approach. Web is becoming the standard user interface.

Apr 1, 2005

In the last five years, new iron ore pellet plants have been built with significantly reduced air pollution levels compared to the older generation of plants. European and American pollution controls are more stringent that in China and Brazil. The recent American plants have successfully employed circulating fluidized beds for sulfur control, baghouses for particulate control, activated carbon injection for mercury and a new design of specialized low-NOx burners.

Jan 1, 2015

By J. G. Bennett

Coal consumption has increased globally by 57% over the last ten years. Underground mining typically provides coal of the highest calorific value and accounts for the greatest proportion of production. Despite a negative environmental image and indeed impact, this industry appears likely to thrive on the global scale for many years to come. Such mining consumes large amounts of electricity with implications for carbon dioxide emission at power plants and emits substantial quantities of the powerful greenhouse gas methane. In response to this significant carbon footprint, the European Union has funded research to examine the potential for a range of improvement technologies in a project entitled Low Carbon Mine Site Energy Initiatives (LOWCARB). Coal properties related to seams and mines, together with longwall characteristics, provide the basis for research into modelling optimally efficient methane drainage with a view to assisting mining as well as maximising electricity generation at surface and hence oxidation of the methane. Possible systems for the oxidation of very low concentration methane in ventilation air, which contributes the greatest greenhouse gas impact due to the volumes emitted, have been studied and modelled. Simulation and investigation of intelligent optimisation of electricity demand patterns provide the basis for reducing the demand peaks at mines and hence the cost and ultimately the carbon footprint of a mine, while specific investigations have been undertaken into ventilation efficiency at an unusually challenging mine and simulation of mine water pumping in order to develop an innovative method to monitor pumping systems efficiency. For post-mining use, the potential of disused shafts for compressed air energy storage to improve the operation of future electricity grids with high renewable energy penetration by reducing peak generation capacity requirements has been studied. While underground coal mining will always by definition be related to a significant carbon footprint, this paper provides an overview of a set of initiatives that can make a positive environmental impact while controlling costs across a huge global industry.

Aug 1, 2013

By W. R. Crane

Mining of the red iron ores of the Birmingham district, Alabama, has _gone on energetically for the past 50 years and has created a large iron and steel manufacturing center, the only important one in the South. The district produces about 10 per cent of all the iron ore mined in the United States and 80 per cent of the Alabama output is red ore ; moreover 43 of the 419 blast furnaces of the country are in the district tributary to Birmingham and produce 7 per cent of the pig-iron output. The rapid growth of the district has been made possible by investigations that have led to radical changes in furnace practice; studies of methods by which the low-grade, highsilica ores may be treated by concentration 1 will give still greater impetus to development. The· mode of occurrence of the ore has made mining practice comparatively simple, but with the rapid extension of the workings underground and the disturbed condition of the ore bed some distance from the outcrop, conditions tend to become more difficult. Stoping, handling, support, drainage, and ventilation are all affected, sometimes favorably and sometimes adversely, by the extended workings and increased depth of cover. Should beneficiatioil make available the high-silica ores of the lower bench of the Big Seam, mining practice must necessarily be adapted to the new conditions and will be rendered more difficult as the weight of cover increases at long distances from the outcrop. The support of workings will require more attention as the weight of cover increases, and the efficient and economical operation of the mines will depend largely upon improvements in mining and handling the ore.

Jan 1, 1927

By Brian G. Thomas

Quality problems in continuous casting of steel can be identified as they occur by monitoring mold signals (level sensor, thermocouples in the mold walls, friction etc.) and taking appropriate action (such as slowing casting speed, changing taper, changing a clogged nozzle, or later visual inspection of the surface for possible downgrading. Surface depressions and groups of deep oscillation marks form at meniscus and reduce local heat transfer as they move down the mold at the casting speed. This slows shell growth, increases shell surface temperature, and causes characteristic dips in mold thermocouple signals. More importantly, they are also associated with longitudinal cracks. Characteristic thermocouple signatures have been identified for many defects, including sticker breakouts, transverse depressions and deep oscillation marks, narrow-face bleeds, transverse comer cracks, longitudinal cracks, mold level fluctuation defects, and other problems. With the help of computational models, these mold signals should be used to troubleshoot defects, and to take appropriate corrective action. Keywords: Continuous casting, defect detection, thermocouple signals, on-line control

Jan 1, 2003

By S. Frimpong, G. Galecki

Dump truck tires are often used in long-haul roads in rugged terrain, with high rolling and grade resistances. These conditions increase the ton-kilometer-per-hour (tkm/hr) or short-ton-mile-per-hour (stmph)rating of tires, leading to tread wear, cuts and complete failures. The load-bearing capacities of these tires are sometimes exceeded, with truck overloading, overstressing, heating and subsequent failures. In addition, truck tire demand far exceeds the current supply capacity, with long lead ordering time. This condition has caused severe tire shortage, and the problem is expected to be sustained in the long-term. Industry has taken extensive practical measures to prolong tire service life with significant results. However, this problem can be solved through fundamental and applied research initiatives. This paper pioneers a research effort in tire service life using multibody physics, fatigue failure modes and soil failure dynamics to develop tire-road contact force dynamics. A virtual prototype simulator of the tire-road contact, using the CAT 775E (with standard tire 24.00R35) was developed and simulated within the MSC.ADAMS/NASTRAN environments. The results show the areas of the loaded tires with maximum Von Mises, principal and shear stresses, which could result in fatigue failure, tire wear and tear and blowouts. The maximum Von Mises stresses on the six truck tires are between 35 and 58 MPa. The maximum shear stresses are also between 19 and 33 MPa. These stresses will cause early tire failures given an average operating schedule of between 20 and 24 hours per day. The isolated areas with maximum stresses will be subjected to further studies to reduce stress intensity while preserving tire performance.

Jan 1, 2012

This paper deals with the evolution of Canadian shaft sinking technology over the last 15 years. Most, if not all, shaft excavation projects in Canada prior to 1990 were sunk using traditional benching methods with labour intensive equipment. In the late-1980s, J S Redpath Limited of North Bay, Ontario, Canada, were contracted to deepen the shaft at Atomic Energy of Canada LimitedÆs Underground Research Laboratory (URL) located in southern Manitoba. The laboratoryÆs role was underground hydrological and geomechanical research, so the project offered both time and opportunity to conduct additional experiments while sinking. The offshoot of the research program was the true birth of the Canadian version of full-face, long round shaft sinking technology. Throughout the 1990s, this sinking method has been further refined over a number of shafts. The results have been faster sinking rates, a safer work environment and an overall improvement in project economics.

Jan 1, 2002

By Andrew Slifka, Pello Uranga, Douglas Glenn Stalheim

Structural steel final mechanical properties of strength and ductility are predominately generated by the final ferrite grain size/packet size and homogeneity of that ferrite grain size/packet size through the cross-sectional area. Forty to seventy percent of the strength components come from how fine the final cross-sectional ferrite grain size/packet size that can be produced.[1] All the ductility properties of structural steels for a given microstructure are predominately driven by how fine AND homogenous the final cross-sectional ferrite grain size/packet size can be refined.[2,3,4] One key ductility property of structural steels used in construction and energy transmission applications is fatigue. Both low and high cycle fatigue can be realized in these end applications, however, low cycle fatigue is typically the predominate mechanism. In construction applications the environment for fatigue is typically air, such as in wind towers or high-rise building construction. In energy applications, there is an interest in high pressure (5.5 – 21 MPa, 800-3000 psi) gaseous hydrogen as an alternative fuel source to fossil fuels. A project to study the effect of the cross-sectional grain size/homogeneity of a relatively pure polygonal ferrite microstructure on the fatigue performance in air and high-pressure gaseous hydrogen has been developed. This paper will discuss the project strategy, microstructure developed for the project and initial test results.

Oct 1, 2019

By Winmill T. F.

The previous papers have been concerned only with the atmospheric oxidation of coals from the Barnsley Seam, for which it has been shown that an adequate explanation of the origin and nature of gob-fires can be based on the reaction between the coal itself and the oxygen of the air without the intervention of any other substance. It becomes of importance, therefore, to ascertain how far a similar explanation will hold good for spontaneous heating in other seams, and with this object in view samples including anthracite and lignite have been taken from a considerable number of pits in different parts of the UK (south Wales, Northumberland and Durham, north Staffordshire, Portrush and Ayrshire), some liable to fire, others not. There is abundant evidence to support the commonly-accepted view that spontaneous heating is due to the heat evolved during the absorption of oxygen from the air by coal or pyrites. The quantity of heat produced by the reaction has been measured and it has been shown that the observed rate of heating of a sample of coal agrees with the rate calculated from the heat of reaction and the rate of absorption of oxygen

Dec 1, 1916

By Armando Vazquez

When water enters the EAF, some chemically dissociates to H2 while some remains as H2O vapor. Depending on operating conditions the levels of combustible gases (CO and H2) and H2O are continually changing throughout the course of any individual heat and on a heat-toheat basis. The EFSOP® system has been implemented in more than 80 installations as a powerful tool to reduce furnace operation costs but with water detection technology the off gas technology is a valuable solution to improve safety. This paper describes the latest results when using Tenova Goodfellow’s new standalone water detection technology that for the first time provides real-time analysis of both H2O vapor and H2 from start-to-end of a heat. It involves a newly designed water cooled probe and heated line that eliminates condensation during off-gas sampling and an analyzer equipped with a proprietary system for analyzing both H2O vapor and H2.

Jul 30, 2018

By Morton Corn

The U. S. Federal Coal Mine Health and Safety Act of 1969 placed limits on the permissible concentration of airborne respirable coal mine dust. Evidence exists which suggests that the effects on health of respirable coal mine dust may depend on both host factors and dust properties other than concentration. Dust particle size, shape, density, specific surface area and chemical composition are among the dust parameters of interest in an epidemiological investigation of coal workers' pneumoconiosis and coal miner exposure to mine dust. The purpose of this investigation was to develop and demonstrate the feasibility of techniques to determine selected properties of respirable coal mine dust. An approved underground horizontal elutriator which samples air at 36 cfm was designed, fabricated and utilized in this study to collect respirable coal mine dust in three mines representing the Pittsburgh, Lower Freeport and Lower Kittanning coal seams. Analytical procedures for measurement of respirable dust sample particle size, density, random projected area, total surface area and chemical composition are presented. Results of analyses of three samples collected in each mine are presented. Up to five full work shifts of sampling were required to accumulate approximately five grams of respirable coal mine dust in each sample. Statistical tests were applied to determine the significance of differences between properties of dust samples collected in the same mine and between arithmetic mean values of dust properties representing three samples collected in each mine. A comparison was also made between

Jan 1, 1972

By Diego Pacheco Wermuth

Micrometric surgical components typically have high geometric complexity and stringent regulatory specifications. These components need to have excellent mechanical properties and a high demand of products. Besides these factors, it is necessary to maintain a low manufacturing cost, performing essential research on new manufacturing technologies. Metal Injection Molding (MIM) is a process that has been explored , providing an interesting alternative for making medical devices. The research in the production of microcomponents obtained for MIM is gaining momentum and prominence, due to low cost and high productivity of this process. This paper is a study and development of feedstocks with AISI 316L alloy , which is known for its biocompatibility. Four feedstocks with 61%vol. of metal powder were analyzed by capillary rheometry and DSC/TGA.

Aug 16, 2017

By J Walasiak

In the climate planning of mines and tunnelling with anticipated poor climatic conditions, and especially in case of longer working shifts, the main question is whether it can be reliably prevented that certain climatic limits laid down be exceeded. Working at high temperature and/or humidity can lead to reduced human working energy û a very important economic aspect û and to a risky lack of concentration on the part of the miners or to heat collapse and extremely dangerous heat stroke. With the Deutsche Montan Technologie GmbH (DMT) climate prediction programs, both the dry and the extremely significant humid heat transfer can be calculated. This is due to the high planning reliability involved. With the help of these climate prediction programs it is already possible to determine the anticipated climatic values for the operation phase as early as the planning stage of new ore or coal fields or of tunnel construction projects and to design the optimum air cooling system for every underground project with due regard to technical and economic aspects.

Jan 1, 2005

By M. J. Ferrante

Relative enthalpies of high-purity disodium hexatitanate (Na2Ti6013) were measured at the Bureau of Mines to provide new thermodynamic data needed to advance the technology of materials. Measurements from 298.15 to 1,478 K were made by drop calorimetry with a copper block. Tabulated values are listed for the standard relative enthalpy, heat capacity, en-tropy, and Gibbs energy function between 298.15 and 1,500 K. Enthalpy data are also given in equation form and are combined with thermodynamic data from the literature to derive values of standard enthalpies of formation, Gibbs energies of formation, and logarithms of the equilibrium constants of formation. Similar calculations were made for the reaction of Na20 with Ti02.

Jan 1, 1986

By V. L. Eardley-Wilmot

Diatomite as prepared for the market is a fluffy, white powder, remarkably light in weight-it weighs only 10 to 15 pounds per cubic foot, or one-tenth as much as sand. Being extremely porous and inert, it is in large and increasing demand for insulation and filtration purposes, as general filler, and for many other uses. Structure Structurally, diatomite is quite different from any other known commercial material. It is composed of myriads of microscopically small, siliceous shells of diatoms which belong to a group of flowerless aquatic plants called algae. When these plants die, the siliceous remains sink to the bottom of the water and form beds of diatomite. Over 8,000 species of diatoms are known, named, and tabulated. The intricate scroll-work and patterns on many of these are one of the marvels of nature, and yet so small are they that from 40 to 70 million separate diatoms may be contained in one cubic inch of material. However, the size and shape of these diatoms, which vary greatly (compare Figures 5 and 6), have an important bearing on the commercial use of the diatomite. The diatoms in the majority of the known deposits are so typical of that deposit that, after a micro-examination, an expert can usually tell not only from what part of the world, but also from what particular deposit, the sample has come.

Jan 1, 1931