Search Documents

By O. A. Carson

Introduction Although the equilibrium conditions of the copper-tin alloys have been the subject of a ?great amount of research, the equilibrium diagram is still in doubt. The first systematic investigation of the series was made in 1894 by Le Chatelier, who published a freezing-point curve. In 1895, Roberts-Austen and Stansfield published the complete liquidus and partial solidus curves, which they modified somewhat in 1897. Their liquidus as given in 1897 is essentially that accepted today (Figure 3). Haycock and Neville also published a liquid us curve in 1897. In 1898, William Campbell published a series of micrographs showing the changes in microstructure which accompanied the thermal changes of Stansfield? s diagram. The classic work on the bronze series was published by Heycock and Neville in 1903. Their diagram was based on both thermal and microscopic evidence, and is the first for this series of alloys which can be considered nearly complete. Further, it was the first bronze diagram in which any attempt was made to apply the phase rule in the interpretation of the thermal and microscopic results. That portion of Heycock and Neville's diagram covered by the present work is reproduced in Figure 7.

Jan 1, 1929

By D. E. Redmon

The Federal Bureau of Mines has studied the locations and general features of 90 pegmatites found in north-central New Mexico. The dominant valuable product of the pegmatites is muscovite, both sheet and scrap. However, the Harding pegmatite in Taos County is mined only for beryl. Many attempts have been made to recover scrap mica on a large scale by mechanical beneficiation of pegmatite, but the operations heretofore have been short-lived. The Globe mine and the Apache mine, both near Petaca in Rio Arriba County, have been the most important sources of sheet mica in New Mexico. Recognition of the growing need for some of the minerals derived from pegmatites led the Bureau of Mines to investigate the occurrences of pegmatite.

Jan 1, 1961

By R. E. MacAfee

THERE have been great changes in the design, capacity, and pressure of steam generating units over the past fifty years. If we go back as far as 1890, the plants then existing were largely horizontal return tubular boilers, hand-fired, with the boilers supported on the brick sitting which was com-posed of red brick with, probably, a refractory lining one brick thick in the combustion chamber. About this time, the water tube boiler began to supplant the H.R.T. boiler and, where new plants were being constructed of any size, water tube boilers were largely installed. In those days, say from 1890 to 1905, a 250 h. p. water tube boiler was considered a large unit. These boilers were largely the straight tube type and were set with the first row of boiler tubes three to six feet above the grates. The brick setting was a combination of red brick and fire-brick. The fire-brick lining in the furnace proper was usually 9 in. thick and in the first pass 4 1/2 in., while the rest of the setting was entirely red brick. These units were largely hand-fired and were expected to produce about 100 per cent rating as a maximum. It may be well at this point to define rating, which is the evaporation of one boiler horse power per hour by each ten square feet of heating surface in the boiler. A boiler horse power is the evaporation of 34.5 pounds of steam from and at 212°F. Consequently, a boiler containing 2,000 square feet of heating surface is rated at 200 h. p. and the evaporation at 100 per cent rating is 200 X 34.5, which equals 6,900 pounds of steam per hour from and at 212°F.

Jan 1, 1939

By C. W. Owings

"PURPOSE OF REPORTMany bituminous coal-mine officials realize that coal dust presents an ever-present coal-mine explosion hazard, and that persons forced to breathe large quantities of it may be more subject to respiratory infection than persons working in less dusty atmospheres. As an outgrowth of the realization that coal dust should be allayed at its source, many mining companies have expressed the desire to install dust-allaying equipment, and in a number of mines, water or wetting solution is being applied on the cutter bars of mining machines, on mobile loaders, belts or conveyors underground, and tops of mine cars. Spraying equipment also has been installed on dumps to allay dust during dumping operations. Dust-allaying equipment has not been standardized, however, because manufacturers have found that many prospective purchasers of such equipment have different ideas. These manufacturers wish to standardize, so far as feasible, the types and placement of such equipment. Many mine officials, although interested, do not know the best or most effective methods for allaying dust.For a number of years the Bureau of Mines has advocated allaying dust by applying water or, more recently, water modified by a wetting agent on the cutter bar of mining machines and by applying water to loaded and empty mine cars in order to keep as much dust as possible from spilling onto the haulage roads. In recent years this Bureau has also advocated applying water with or without a wetting agent during mechanical loading of coal and during unloading of coal from trackless cars or buggies and from elevating conveyors. It has now become apparent that specific arrangement of pipes, hose, and nozzles should be standardized to at least some extent. It is the purpose of this report, therefore, to give in detail suggested arrangement of dust-allaying equipment in the hope that both manufacturers and mine officials will have available dust-allaying equipment with maximum efficiency to do the desired work."

Nov 1, 1945

By Raymond E. Connell

From a macro business process perspective, if what we do in the Mining Industry is find material, dig it out of the ground, convert it to a product and sell it, we are in what might be considered a "simple business". If it is so simple, where does information technology fit? How does it affect our industry? Is it a strategic tool for our industry? What approach should we be employing to ensure we are utilizing information technology effectively? How is information technology integrated or tied together with other areas in the organization such as process control? What kind of people and skill sets are required to support the whole area of information technology? What effect does information technology and automation have on streamlining and rethinking the way we do business in the 90's. This paper covers how these areas have been addressed within the Noranda Group of Companies. It reviews how information technology has evolved, the approach, and what effect it has had on a diversified natural resources company in the mining and metals, forest products, and oil and gas industries.

Jan 1, 1993

By Norman Paley, Zachary Pickett

The Red Dog Mine is a high-grade zinc-lead mine located in northwest Alaska which began operations in November 1989. In June 2014 the upper half of a charge in a trim shot in the Aqqaluk pit deflagrated. No other holes in the area were observed to react and the remainder of the pattern was shot without incident. This was the only known case of a deflagration in the 25 years of operations. As part of the investigation into the cause of this incident rock samples were obtained from the area of this hole and from other areas in this pit.

Feb 1, 2020

By K Devencorn

The development of robust, economical transport infrastructure has been identified as a key driver to sovereign economic growth. Notwithstanding the value of undeveloped mineral resources, unless they can be brought to market they are of little value. Within a global context, the continent of Africa probably faces one of the most significant transport driven economic development programs as countries strive to unlock their much sought after resources.The UN’s Africa Review Report on Transport (United Nations Economic and Social Council, 2009) provides an excellent context for the issue facing African countries and the potential for investment in transport to solve many of the intrinsic problems they are confronted with. With little exception, economic development in Africa is very likely to be driven ‘off the back’ of transport development – and more specifically from heavy-haul rail as a means by which economic wealth can be derived from export of the continent’s vast natural and mineral resources to the world. The report found:transport is a key driver of economic development and poverty reduction;road transport is the most dominant mode in Africa;the ‘Cost to Market’ of African goods is hampered by the reliance upon road transport;the cost of road transport is not just economic – 19 per cent of the world’s road fatalities were recorded on African roads;African railways are seen to be disjointed and under-utilised;Africa’s ports are key to export trade - yet only six ports (three in Egypt, and three in South Africa) handle about 50 per cent of the continent’s total container traffic;the cost of transport is increasing making African trade even less competitive; andsignificant negative impacts of Africa’s reliance on road transport – health, and greenhouse emissions.We understand that mining the resource is only part of the solution – it has to be put to market at a competitive landed cost.Most African countries face huge costs associated with transport development and ongoing operation – in many cases beyond their available resources.The Australian rail industry has faced and solved many of these challenges.

Nov 22, 2011

By Mark Gilliam

Control of true steel level in the tundish during casting is desired in order to maintain the correct pressure head and thus provide a stable flow to the mold. Also the control of tundish draining prevents slag carryover and can increase yield at each end of cast sequence. At Steel of West Virginia (part of the SDI Group), it was understood that to be able to measure the true steel running level and control the drain level at the end of casting would be a great benefit during production at their three strand billet caster. This paper sets out to show how an evaluation process was started to find the best method to determine steel level in the tundish and to prevent the steel level dropping low enough to allow slag to enter the mold. Also how the decision was taken and a real time molten steel measurement system was installed and by utilizing the resulting data in the process, how slag in the mold was removed as an issue, how lost production was reduced and how consistent steel level has provided constant casting speeds and improved stream integrity, all leading to realized quality improvements. Other areas discussed within the paper will be the training of operational staff, the difficulties to be overcome when first installing new equipment and how these teething problems were cured by close co-operation between the steel plant and the equipment suppliers. In conclusion the paper will discuss the production improvements achieved, production cost savings at the plant and how the generated data was integrated into the plants process control system.

Aug 16, 2017

The purpose of this study is to formulate practical guidelines for active underground mining in close proximity to water bodies. This was accomplished through systematic completion of three phases of study: I) Collection and Documentation of Data; II) Application of Existing Guidelines to Case Histories of Previous Inundations; and III) Development of Recommended Guidelines for Underground Coal Mining Near Bodies of Water. Phase I of the study involved a worldwide data collection effort designed to obtain foreign and domestic guidelines for mining near water bodies, and accident records and case histories of accidental mine inundations. Within Phase II, existing guidelines were categorized and classified and then evaluated as to their effectiveness in precluding past inundations had they been in effect at the time of inrush. Advantages and disadvantages of existing guidelines were defined. Drawing on the broad data base established in previous study efforts, Phase III was directed at development of viable guidelines to promote the greatest possible coal extraction while precluding accidental mine inundation. Two levels of guidelines are presented; Level I Guidelines require little or no subsurface exploration on the part of the mine operator, while Level II Guidelines recommend various testing and investigative procedures to permit greatest possible mineral extraction. This report presents findings and conclusions of the study.

Jan 1, 1976

By Clyde E. Williams, JAMES L. GREGG

THIS review of the past year's progress in iron and steel metallurgy presents examples of only a few of the interesting or important accomplishments made in the United States. In the field of iron ore concentration increased attention was given to the study of the more difficultly separated wash ores and some progress was made in tabling. One difficulty with the table, in concentrating iron ore where the percentage of concentrate in the feed is large, has been the removal of fine silica from the thick layer .of concentrates in the cleaning zone. One company has -Made an important contribution toward the solution of this problem by an extension of the well-known plateau principle. By a special riffling of the plateau section of the table, the concentrates are crowded together. This action forces the fine silica to the top of the bed in the cleaning zone, whence the cross-flowing currents of water -can wash it into the middling product. Some work has been done on the application of froth flotation to the concentration of iron ores. Laboratory experiments were made at the Colorado School of Mines in which hematite was, successfully floated. Using oleic acid as a frothing and collecting agent and sodium carbonate as the conditioning agent, a high recovery of rich ,concentrate was obtained. A laboratory flotation unit is in use at Taconite, on the Mesabi range, and a commer-

Jan 1, 1932

By J. S. Kirkaldy, W. J. Slater, G. R. Mason

Activation analysis for copper and manganese in 10 mg samples machined from aluminum-base diffusion couples has been used in the study of ternary diffusion in the Al-Cu-Mn system. The accuracy, economy and convenience of the method are considered to be very competitive with other methods for analysis of such small samples. Neutron-activated aluminum-zinc alloys in the range from 10 per cent to 100 per cent zinc have been equilibrated with a known volume and the vapors subsequently condensed and collected. The vapor pressures relative to pure zinc (the thermodynamic activities) have been determined at 550°C' by recording the relative count of /'-rays from zn65 in the collected samples. The method is a sensitive one, although subject to serious obstacles to experimental accuracy.

Jan 1, 1961

By Neeraj Saxena, Madhu Huggahalli, Jerry Bednarski, Ken Grieshaber, David Stoffel

"The use of oxy-fuel burners in secondary aluminum melting applications offers several advantages over air-fuel burners including reduced fuel consumption, faster charge to tap times and lower NOx emissions. Their successful, safe and economical use in a furnace depends on several factors and considerations such as burner and flue placement, metal circulation, charge practices and the type of refractory used in the furnace.These factors required in the successful conversion of furnaces from air-fuel to oxy-fuel based burners are discussed in this paper. Critical parameters are identified and examined using computational fluid dynamics (CFD) simulations. Parameters are estimated via laboratory testing and validated through trials performed at commercial installations. Guidelines and a simplified approach to estimate a priori the economic impact of converting from air-fuel to oxy-fuel are presentedThe final products of this research are simplified and validated tools for modeling aluminum furnaces. These include improved heat and energy balance models and parameterized CFD solutions which provide rapid customization to individual furnace configurations. These tools provide field engineers with immediate and accurate predictions of performance, allowing for repeated precise scenario analyses."

Jan 1, 2001

By W. Gibson Jaworek

It has become apparent in recent years to everyone intimately concerned with the future of the American fuels industries that the growth in demand for energy has become a topic receiving considerable attention, and that investigators are leaning more and more toward a mathematical approach to deduce what pattern that growth will follow. Though coal has been included by necessity In all-studies of future energy markets, it has not been the subject of mathematical analysis or description as frequently as has been total energy or some of the other fuels, particularly petroleum, It is the intent in this particular paper, to subject bituminous coal consumption to a preliminary mathematical scrutiny which can lead to a more logical estimation of the general level of bituminous coal consumption for the next decade, as well as formulating an approach toward describing how coal consumption may vary as the result of the annual variations in activity in the United States, economy, The approach utilized is more sophisticated than the mere projection of the historical trend of bituminous coal consumption. Such a projection would lead to a continuation of the recent decline, indicating that coal consumption would reach zero some thirty years from now. On the other hand, the mathematical analysis described here is a relatively simple, straightforward approach and- is not intended to represent the-ultimate in mathematical economic analysis as now practiced, It is hoped that this will contribute to our knowledge of bituminous coal markets. Even more, it is hoped that it will help arouse a greater interestin utilizing mathematical and statistical analysis when studying the bituminous coal industry. - Since this is a preliminary study, comments and criticisms are anticipated.

Jan 1, 1960

By J. Mackintosh Bell

External trade strongly influences the well being of all nations. In the modern economic mechanism, no country is so well endowed that it has not to import commodities from others and to export its products in turn to make good its deficiencies, to rectify or improve its financial structure. From the standpoint of international commerce, Canada is strategically well placed. On the south she is bounded by the richest country in the world. On the east she faces the Atlantic, on the west the Pacific. On both coasts there are fine harbours to which lead great lines of railway that span the continent. Canada is now fifth among the exporting nations of the world. For disposal abroad, she has enormous quantities of primary commodities and substantial amounts of manufactured goods as well. But she is far from being self-sustaining. She is unusually dependent on foreign trade, not only because of the commodities she has to sell but because of the lack of many essential articles she does not or cannot produce. To Canada, external commerce is vastly more important than internal trade. The wealth of nations is decided by their ability to produce more than they need, to sell more than they buy, and to build up favourable balances resulting from trade or services. With few countries, however, are returns perennially satisfactory. Fruitful periods are followed by leaner years. In times of prosperity foreign credits are increased, monetary systems strengthened, reserves accumulated to withstand recurring days of strain. Today, the foundations of financial systems are being re-examined, "dogmas hitherto accepted as canonical are being questioned" . It is not only in Europe and America that men search for illumination in problems arising from monetary restrictions.

Jan 1, 1933

By J. A. Organiscak

The U.S. Bureau of Mines investigated the relationship of bituminous coal seam parameters and the amount of airborne respirable dust generated at longwalls. Dust and coal samples were obtained from 20 longwalls operating in geographically representative coalfields throughout the United States. Statistical analyses of coal seam parameters and airborne respirable dust measurements indicate a likely causal relationship between seam type and respirable dust. Low-ash, high-volatile coal seams were associated with higher airborne respirable dust levels. A negative linear correlation (significant at the 95-pct confidence level) was observed between the seam's ash content and airborne respirable dust, explaining up to 18 pct (R2 = 0.18) of headgate dust level variation and up to 15 pct of tailgate dust level variation. Volatile matter was found to have a positive linear correlation with tailgate dust level, explaining 16 pct of the variation. Further data examination indicates that these relationships with dust are most likely nonlinear, because of improved R2 values over the linear correlations. However, a notable portion of longwall dust production is influenced by other operational parameters, so additional research under more controlled conditions is needed to determine the seam's causative functions.

Jan 1, 2010

By Roger L. Williams

The Zinc Corporation of America Monaca smelter continues to use the St. Joe-developed electrothermic process for producing zinc metal and zinc oxide. As we enter the 1990s, the electrothermic process flexibility permits treatment of larger quantities? and lower-grade zinc-bearing recycle materials. A new sinter plant having one large sinter machine will increase sinter feed production required to meet our capacity target of 150,000 tons per year.

Jan 1, 1990

By A. Tohn, L. May, Adham. K.

The path from process conception to commercial implementation poses significant technical, economic, and sometimes political challenges for every project team. Solving the technical challenges typically distinguishes successful projects from those that fail. Here, the authors provide an outline for technical success based on lessons learned from years of experience in process design and R&D. Challenges faced by new technology developers, with regard to design and definition, are described. Experience-based methods to avoid missteps are shared. Special emphasis is placed on the selection of viable unit operations, definition of known and unknown parameters, experimental screening of options, and piloting for scalable design information. Use of computational models to define, assist, and interpret the pilot operations and results are described. Furthermore, the value of active collaboration amongst the design, research, and owner team is demonstrated.

Jan 1, 2011

By William Gleason

"The times they are a changing, and, for the mining industry, the optimism is high. On Nov. 8, Donald Trump was elected as the 45th president of the United States, and the Republican Party won a majority of seats in the U.S. Senate and the House of Representatives, ushering in what many hope will be a positive change for the mining and extractive minerals industries.Trump has stated that one of his top priorities as president will be to increase spending on the nation’s infrastructure, which could help spark a boom for mining. He has also pledged to bring back coal jobs and reverse many of the environmental regulations that were put in place by the Obama administration. However, before the mining industry gets too far ahead of itself and plans for another Super Cycle, there are stark reminders that any work in the natural resources sector is complicated and challenging. On Dec. 4, the U.S. Army Corps of Engineers announced that it would not grant an easement that would allow the Dakota Access Pipeline to pass under a portion of the Missouri River in North Dakota. The proposed crossing of the oil pipeline is approximately a half a mile upstream from the Standing Rock Sioux’s Reservation, and for months, hundreds of protestors camped out at the site in an effort to halt the project, saying they feared how it would impact water supplies and sacred lands.Energy Transfer Partners, the company building the pipeline, said the pipeline is a $3.78-billion investment that will connect the Bakken and Three Forks production areas to major refining markets. The company signed voluntary easement agreements with landowners representing more than 85 percent of the properties along the four-state route but faced an organized protest from the Sioux Nation at Standing Rock. The protest gathered momentum and support through social and traditional media and became the focal point of global environmental and indigenous activism. The protestors claimed victory, at least temporarily, when the Corps of Engineers said it would look for alternative routes for the project. It’s a decision that could lead to a lengthy environmental review and one that has the potential to block the construction of the pipeline for months or even years."

Jan 1, 2017

By W. E. Wrather

CURTAILMENT of production was a matter of far more serious concern to the oil industry through 1933 than the search for new supplies of oil. The huge reserves of crude, built up during past years, instead of inspiring a feeling of security, were viewed apprehensively. The status of past laws and court decisions seemed to guarantee to operators the right to produce oil at will, and this entrenched privilege was so widely adhered to that the market was-in a constant state of chaos. The more modern idea of the ownership of oil in place and correlative rights gained headway slowly, since usually there were enough belligerent producers, staunch believers in the old established order, to defeat the efforts of the majority who sought to' introduce order and restraint. State regulatory commissions were unable to cope, with the rebellion among producers with the result that those who abided by proration rulings were penalized, while those who flouted the rulings and produced unrestrainedly were able to make profits on large volumes of flush oil even at low prices. This situation, known in the vernacular as the "hot 'oil" problem, became so acute that the industry was threatened with ruin. The low price for 36c A.P.I. in the Mid-Continent came in April. at 25c per barrel 'but gradually moved upward to the long-hoped for price of $1.00 per barrel in October, after the Federal Government had taken a hand in the matter and effectively allocated production among the oil producing states and materially curbed the "hot oil" runs.

Jan 1, 1934

By T. Shibaraki

A new larger, more efficient and economical Mitsubishi furnace line at Naoshima was put into operation in May 1991. Naoshima Smelter had produced previously about 230,000 mtpy anode copper with two smelter lines, i.e., a conventional reverberatory furnace line and Mitsubishi furnace line, which had been shutdown at the same time of the start up of the new smelter. At the beginning of the operation, there were several initial problems at the area of off gas trains and feeding system. By overcoming them now the process has been continuing satisfactory operation at the design rate. The paper describes about the design concepts and the actual operation of the new smelter.

Jan 1, 1993