Search Documents

By C. M. Young

Bituminous coal piled in heaps or bins frequently undergoes a process of spontaneous heating as the result of the absorption of oxygen. It seems probable that the first absorption of oxygen by coal which has not previously been exposed to the air may occur as a condensation or a combination of oxygen in some form which does not result in the production of carbon dioxide, but slow combustion soon begins. The absorption of oxygen is accompanied by an increase of temperature, and this by an increased rapidity of absorption; hence the dangerous condition proceeds from bad to worse, until the kindling point is reached, unless the process is interrupted. A dangerous rise of temperature can be prevented by excluding oxygen, by increasing the bulk of coal in proportion to its surface exposed, or by circulating enough air to dissipate the heat produced. The storage of coal, in practice, varies from almost complete exclusion of oxygen, by storing under water, to such freedom of access as exists when the coal is stored in open piles. Oxygen available for absorption by coal is supplied by the air in the interstices between lumps and by additional air which may enter the pile through circulation. The size of the coal largely affects both of these supplies; for if the fragments are small the spaces between them constitute a small percentage of the total volume, and little oxygen will be available unless the circulation of air brings in a fresh supply, while with large fragments the percentage is relatively large; circulation also is much easier through a pile of coarse lumps. In the case of lump coal, although a large amount of air may be present, the exposed surface is comparatively small and there is little opportunity for the absorption of oxygen to be so rapid as to cause dangerous heating. Attempts have been made to prevent heating by allowing a sufficient circulation of air to carry off the heat generated; obviously this method cannot be applied to fine sizes nor mixed sizes. When storing coal at the University of Illinois, an attempt has been made to use so much fine coal and to pack it so thoroughly as to prevent circulation of air, while also reducing the original air in the pile so as to prevent heating. This method has been fairly successful, but in some

Jan 1, 1918

By Karsten Beckhaus

"Abstract Tremie concrete for special geotechnical works needs special properties, especially during the casting process. Today’s execution standards for bored piles and diaphragm walls, EN 1536 and EN 1538, as well as the draft version of concrete standard EN 206, all comprise regulations for deep foundation concrete which have not been changed for decades. Considering the recent development in concrete technology at the same time and its actual state-of-the-art, it is essential to develop new normative specifications and specification requirements.GeneralTo allow the required integrity and quality after placing and hardening, concrete for structural elements like bored piles or diaphragm walls, used as foundations of high-rise buildings or as retaining structures for large and deep building pits, must have adequate workability and stability.In addition to requirements on mechanical properties and on durability, both of which have increased within the last decades, concrete must be suitable for being cast in deep or extremely deep excavations, see figure 1. Today’s specialist foundation engineering machinery makes it possible to drill or cut down to in excess of100 m depth. Concrete technology has developed and allows the use of high performance concrete for deep foundations. But is this capability represented by actual regulations?It has become very common for the industry to supply or use concrete with low water cement ratios, nevertheless highly flowable and set-retarded for several hours if needed. Very low water cement ratios allow design strength of 60 MPa or higher (Larisch, 2011), and a very low porosity which is required for a long service life in aggressive conditions, e.g. by chlorides.To achieve best performance, it is obvious that the concrete must completely fill the excavation and fully embed the reinforcement. As vibration of deep foundation concrete is (usually) not allowed and was anyway inefficient, deep foundation concrete must be designed to self-compact under hydrostatic pressure. Generally, it must be considered that after placement the concrete’s quality cannot be influenced anymore. Therefore, both the pouring procedure and the concrete quality must be adequate."

Jan 1, 2014

By A. Luckita, A. Samtani, R. Barus, J. R. Donald, J. Syarifuddin

In conventional Rotary Kiln-Electric Furnace (RK-EF) laterite nickel processing, management of dust continues to be problematic. A more efficient processing of dust represents an opportunity for energy efficiency, increased production, and productivity. PT International Nickel Indonesia (PTI), together with Vale Base Metals Technology Development (VBMTD), has successfully developed and implemented a novel flowsheet enhancement that capitalizes on these opportunities. In the novel flowsheet, the dust recycle stream is moved forward in the RK-EF laterite nickel smelting process. The dust is injected into the kiln's main burner, as opposed to being recycled to the dryers. A similar treatment of dust is commonly practiced in the cement industry; however, application to nickel smelters has not been fully developed to date. This paper describes this dust insufflation technology, the process through which it was developed for laterite nickel processing, and summarizes the lessons learned. A key conclusion is that successful new technology development requires a multi-disciplinary team involving members from research and development, study management, engineering consulting firms, project implementation management, process technology and operations.

Jan 1, 2011

By Keith Pucalik

Understanding Vibrations fr om Blasting focuses on explaining blast vibrations and their effects on people and homes while keeping an eye on the importance of the use and significance of explosives in our daily lives. Unlike many predecessors, this film will help blasting pro f e s s i o nals explain blast vibrations and address many of the layman’s most fre q u e n t l y asked questions. The film can be used in pubic hearings, given to homeowners during preblast surveys, or played at educational seminars for professionals. The film can also be used after blasting has begun and residents have already experienced vibration events.

Jan 1, 2004

By R. L. Machunda, A. M. Rugaika, D. D. Mdachi

Sedimentary and igneous rocks are the two primary sources of phosphate that are mined and beneficiated to fertilizer. During the beneficiation process, phosphate is lost into the tailings. We investigated phosphate concentrations in tailings dumps at Minjingu mine, Tanzania using energy-dispersive X-ray fluorescence spectrometry to quantify the chemical compositions. The phosphate content in the tailings varied from 12.91% phosphorus pentoxide (P2O5) in Tailings 2 to 19.61% in Tailings Dump 1. The naturally occurring phosphate concentration in rocks ranges from 3% to 35%, and phosphate tailings from various locations with P2O5 concentrations as low as 6.46-12.65% have been beneficiated to commercial fertilizer. Our investigation revealed that phosphate concentrations in Minjingu tailings may be sufficient to be recovered for commercial applications. Suitable recovery methods are discussed, and we recommend that beneficiation should be performed to minimize the loss of phosphate into tailings. Further research is needed to identify the optimal beneficiation methodology.

Aug 8, 2024

By U. Ulusoy

Surface roughness and acuteness are known as the two of the main properties of the particle morphology affecting the behavior of the powders in the process. Since the techniques used for the morphological characterization of powders by 2-dimensional microscopic measurement from the polished sections that have some disadvantages, the 3-dimensional analysis has often relied on measurements of particle morphology. A review of literature data was presented for high-grade barite and pyrite particles ground by ball and autogenous mills to determine the morphological properties using a new 3-D approach based on BET nitrogen gas adsorption and Permaran methods. Micromeritics Flowsorb II 2300 instrument which employs BET nitrogen adsorption technique was used for the specific surface area measurements and the roughness of the particles. Permaran (manufactured by Outokumpu Oy) was used for the measurements of airflow resistance of powder samples for the acuteness. Spherical glass beads were used as reference sample for the acuteness measurements. The obtained parameters, which are surface roughness and acuteness, were corre-lated with the floatability performance of those mineral particles. The flotation performances of those particles ground in different mills (ball and autogenous) were also evaluated by a Hallimond tube. The results showed that lower roughness and acuteness values caused higher flotation recoveries for both barite and pyrite particles that were tested independently in different type of the mills. In other words; particles with smooth surfaces resulted in better floatability for barite and pyrite minerals studied.

Jan 1, 2014

By A. Longval, Q. Jiao, T. Shannon

In 2000, Xstrata Zinc (former Falconbridge Ltd.) Brunswick Smelter commissioned a modified lead blast furnace. Since then, efforts have been made to improve its operation in order to achieve optimal operation in terms of coke consumption, lead loss to slag, and improved environmental and hygiene conditions. This paper will review the important step changes in operational philosophy, undertaken since 2004, for the control of the blast rate, oxygen enrichment in blast, slag chemistry and charge level. Furthermore, a review of the improvements made in secondary materials consumed at the blast furnace will be made. This paper will also discuss the significant reduction of the frequency of accretion removal as a result of improved furnace operation.

Jan 1, 2008

By H. E. Dresch

This report summarizes the work accomplished under Bureau of Mines contract H0188068. The contract required design and construction of a high voltage (7.5 KV) explosion proof cable connector for use on underground coal mine drag cables. A connector was constructed with elastomeric phase insulators that provide insulation shielding throughout the connector length. Connector housing was made of flame resist-ant cast poly urethane with no exposed metal components. Electrical and mechanical testing of the completed coupler resulted in satisfactorily meeting most of the design testing requirements.

Jan 1, 1981

By D. Pawelus, J. Butra, R. Debkowski, M. Szpak

Impact of horizontal stresses on stability of underground workings in mines is a very important issue in underground mining. Identification of the initial state of stress in the rock-mass should be one of the main actions taken into account while designing and carrying out the mining activity in underground mines. The paper presents the tests on three dimensional stress pattern in Polish copper mines, owned by KGHM Polska Miedz S.A. Group, carried out in 2012. The research program covered 7 measuring stands in two mines; their average depth was about 1000 m. The main aim was to identify the values and directions of horizontal stresses in order to optimize the extraction and to improve the safety. The overcoring method with the use of CSIRO HI type probe was applied. The paper also describes the measuring technique which was developed for the purpose of specific mining and geological conditions of KGHM mines, taking into consideration the natural hazards encountered there as well as technical and operational capabilities with regard to drilling equipment. The experience gained during the underground measurements and the issue of making such measurements in underground copper mines in Poland are presented in the paper. The stress patterns obtained during the underground measurements are of application importance for the process of designing the spacing of mine workings and improving their stability and mine support selection.

Jan 1, 2015

By B. Crane, S. Schwartz

"IntroductionThe Cape Breton Development Corporation (CBDC) located in Cape Breton, Nova Scotia, in eastern Canada, was established in 1967. Its mandate at that time was to facilitate a phased downsizing of the coal industry and developing viable replacement industries. The oil crisis in the early 1970s changed CBDC’s mandate and focus was modified to increase coal production to support Nova Scotia Power Commission’s “off oil” policy for their power generators. In the late 1980s the mandate to develop viable replacement industries was eliminated and CBDC became primarily a coal mining company. CBDC presently operates two underground coal mines, Phalen Colliery and Prince Colliery, using a retreat longwall method of mining. Both mines operate beneath the Atlantic Ocean. CBDC also operates associated infrastructure — central workshops, a railroad, coal preparation plant, and international pier. The Need For Substantial ChangeOver the last few years, CBDC has been facing some challenging issues, including improving labour management relations and achieving financial self-sufficiency and profitability. Recent achievements with regard to human resource issues, especially in the areas of collective bargaining, absenteeism, and attendance, show noticeable improvements. All participants should be commended for successfully concluding the collective bargaining process with all four CBDC unions, CUPE; CAW; IAM&AW; and UMWA. However, although these changes are encouraging, even critical in the short term, they are not sufficient to ensure the long-term viability of the company. Market ForcesShort- and long-term financial realities are drawing the need for further substantive changes. The corporation has a mandate to achieve financial self-sufficiency by the year 1999. This goal can only be achieved through a combination of cost reductions and productivity gains, specifically, a reduction in the workforce of 658 and an increase in production of 800 000 tonnes annually. This increase in productivity requires CBDC to re-think the way it does things.In the longer term, CBDC faces even greater challenges. The energy market is becoming more competitive. The electrical utilities across Canada are anticipating deregulation and are positioning themselves for the resultant competition. As primary fuel supplier to Nova Scotia Power Inc. (NSPI), the corporation will have to become ever more competitive to stay in business."

Jan 1, 1997

By H. S. Martin

This paper, describing the concentrating practices at the plants of the Utah Copper Co., is one of a series being prepared by the United States Bureau of Mines in which the data are given in as nearly uniform c manner as possible. The Magna mill is 19 miles west of Salt Lake City on the routes of the Lincoln and Victory highways, and the Arthur plant is 1 mile west of the Magna mill. Both are on the main road west of the town of Magna and east of the town of Garfield.

Jan 1, 1931

By G Richmond, J R. Glen

Western Metals Mt Gordon Operation is a copper mine and processing plant situated 120 kilometres north of Mt Isa. The unique Mt Gordon copper process utilises a whole of ore acid/ferric pressure leach to produce copper cathode from the Esperanza massive sulfide copper orebody. Esperanza ore contains chalcocite, covellite and minor chalcopyrite hosted in a massive pyrite matrix. These ore stocks will be depleted in late 2003. Recently the process circuit has been upgraded to allow the treatment of lower grade Mammoth ores. These include the installation of a ball mill to complement the existing SAG mill, a single stage rougher flotation circuit and a tailings thickener. The leach bleed neutralisation plant was also upgraded at this time. Commissioning of these new circuits occurred in March 2003 and involved all the challenges of ensuring current production levels were successfully maintained while new process steps were incorporated into the whole circuit. This paper explains the background flow sheet of the patented Mt Gordon process and the reasoning behind the enhancements required for an already successful copper leaching circuit. Included are discussion of the influences of the new ores on individual process components such as comminution, leach chemistry and solid/liquid separation. Longer term ore processing options are also discussed.

Jan 1, 2003

By John E. Hamak

The U.S. Bureau of Mines estimates the identified helium resources of the United States at 630 Bcf as of December 31, 1990. This includes 295 Bcf of demonstrated reserves, 87 Bcf of demonstrated marginal reserves, and 42 Bcf of demonstrated subeconomic resources. The identified resources include 161 Bcf of helium in inferred and marginal reserves and 45 Bcf in inferred subeconomic resources. The identified helium resources contained on Federal lands are approximately 170 Bcf, including 32 Bcf in underground storage in the Cliffside Gasfield near Amarillo, TX. In addition to the identified helium resources, undiscovered helium resources in the United States are estimated at a most likely volume of 103 Bcf, with a maximum volume of 259 Bcf and a minimum volume of 41 Bcf. Also reported are 43 Bcf of helium in nonconventional and low-helium-content natural gases. Current extraction of helium in the United States occurs mostly from natural gases produced from the Hugoton gas area in Kansas, Oklahoma, and Texas, and the Riley Ridge area in southwest Wyoming. Helium extracted from natural gas in the United States in 1990 was 2.5 Bef. If current trends continue, some shortfalls in helium supply may occur in about 5 to 10 years.

Jan 1, 1993

By W J. Riva

This paper reviews the circumstances that led to the development and construction of a commercial-scale vertical shaft carbonizer at Conmore, Alberta. This form coking process may be regarded as having potential application in other areas. Coal pelletizing offers a promising method of decreasing coal agglomeration costs under certain circumstances. Pellets can be rolled easily from -35-mesh coal, provided that a minimum of -200-mesh coal is present. Bentonite was found to be the best binder and was most effective when added in amounts of about 2 per cent. The water content of the coal pellets was observed to vary from 18 to 23 per cent. As a by-product of this investigation, it seems possible that fine coal could be converted into stoker feed by this process. A short investigation of the effect of heating rate on the carbonization of pellets was conducted. The low maximum heating rates in certain temperature ranges, necessary to avoid crack formation in the pellets as reported by other

Jan 1, 1964

By J Knecht, R Klymowsky, E Burchardt

The wide spread introduction of SAG mills into grinding circuits 20 years ago was the last development which had a major impact on the design and economics of comminution circuits. Single SAG mills were able to replace batteries of high maintenance and cost intensive crushers in order to achieve high throughput operations. Today, where the head grades of gold and copper ores are falling, there is again a strong need for a significant breakthrough to reduce investment and operating costs as well as improve metal recoveries. High-pressure grinding rolls is the new technology available to meet this challenge. HPGRÆs are state-of-the-art in several mining and minerals applications such as the grinding of iron ores and concentrates, and diamond bearing ores. Reasons for their success in these industries are overall cost reductions and improved product properties achieved by the application of high compressive forces. But these ores are relatively soft, with unconfined compressive strengths up to 150 Mpa.

Jan 1, 2000

By T. D. Hackett

Multislice mining methods were analyzed by the U.S. Bureau of Mines to determine their application to western United States thick coal seams; ground control, geology, and costs were considered. Multislice mining is used in widely varying seam conditions worldwide, including flat seams too thick to mine in a single pass, pitching thick seams, and seams containing a rock parting. Longwall multislice methods predominate, but room-and-pillar variants also exist. The initial use of the method in western seams is planned at a deep Colorado mine where a rock parting will be used to separate two slices mined by longwall. Ground control and spontaneous combustion are major hazards associated with multislice mining. A well-consolidated upper slice gob can reduce ground control problems and provide a seal against spontaneous combustion. Geologic analysis indicates that the consolidation of the gob depends on the composition of the upper slice roof, the presence of water, and sufficient overburden pressure. A geologically competent intermediate rock parting can also reduce ground control problems and seal against spontaneous combustion. To compete in western coal markets, the cost of multislice mining must be within the range of normal longwall costs. Analysis indicates that multislice operating costs should be within this range, and that multislice mining costs decrease as panel width increases. Relatively wide (600 to 800 ft) panels also provide increased coal recovery.

Jan 1, 1990

By T. A. Lloyd

"This paper indicates the extent to which Canadian coal mine operators have taken advantage of developments in the science and technology of coal that would allow them to better satisfy changing market demands through improving the properties of their products. At some mines, no attempt is made to alter the coal from its as-mined condition, but at most mines grading into various size ranges and hand-cleaning of lump sizes is undertaken.Over-all, Canada Jags behind most of the other major world coal producers in the proportion of its coals being processed in wash plants. To some extent, this is due to the fact that a high proportion of the coal production satisfies market demands without such treatment. On the other hand, a few of the coal mines in Canada, which produce about 25 per cent of the nation's total coal output, have in operation some of the most modern coal beneficiating equipment available, including jigs, flotation cells, water cyclones, centrifuges, disc filters and thermal dryers."

Jan 1, 1968

By T R. Meng, C Wu

After carrying out a brief review of the existing safety assessment criteria for the spontaneous detonation of explosives in the mining of sulphide ore deposits in China, and giving a detailed description of the dynamic process and mechanism of the spontaneous detonation of explosives and the relative factors, the latest research results of three kinds of explosives reacting with a group of sulphide ores are presented, based on a reliable experimental method. Afterwards, a complete safety criterion for spontaneous detonation assessment, which depends on the hole temperature, the water solution Fe2+ and Fe3+ and the pH value, is established to determine (he safe charging time of explosives in variable conditions. The criterion is verified as correct by a large-scale field test.

Jan 10, 1996

By A. J. Brown

This paper presents an economic evaluation of resin ion exchange and solvent extraction for the purification and concentration of uraniferous solutions derived from sulphuric acid leaching operations. Capital and operating costs are related to the uranium tenors of pregnant solutions. The conclusions drawn herein apply only to cases where resin and liquid ion exchange are technically feasible process alternatives. It is shown that solvent extraction is economically favoured for pregnant solutions at tenors greater than 0.90 gpl U3O8. Pregnant solutions with tenors below 0.35 gpl U3O8 are best treated by resin ion exchange. Between these concentrations, the economics are marginal and the favoured process is indistinguishable within the limits of accuracy of this study.

Jan 1, 1979

By Victor Stancovski, Uday Pal, Stephen C. Britten

"An in situ electrochemical technique for measuring the concentrations of easily dissociable oxides in slags at temperatures between 1200-1600°C is being developed. The technique utilizes a partially-stabilized-zirconia solid electrolyte (PSZ), which conducts oxygen ions, to separate a reference-gas compartment from the slag of interest. Three types of measurements are currently under investigation which yield different information concerning the slag phase and hence will be combined into a single amperometric device for monitoring the properties of easily dissociable slags.Type I utilizes an open-circuit-voltage measurement between the reference gas and the slag phase. Type II utilizes a potentiostat to apply a direct current potential step or sweep between the inner and outer compartments of the electrolyte, driving oxygen ions from the slag into a reference gas. With the use of open-circuit-reference electrodes, the resulting current-potential profile reveals the dissociation potential and concentration profile of dissociable oxides such as those of iron, manganese, and chromium. Information on the transport properties of the cations can also be generated from these measurements. Type III utilizes a potentiostat with reference electrodes to carefully electrolyze a known volume of slag by removing large quantities of oxygen ions from the slag to the reference gas. The coulombs of charge removed at different applied potentials can be used as a direct indication of the concentration of each dissociable oxide species present within the slag."

Jan 1, 1997