Search Documents

By A. L. Williamson, G. Savci

Hydrologic assessments of existing and proposed waste rock stockpiles (WRS) are typically required for application of operating and closure permits at mine sites. The results of these assessments can be used to determine the applicability of the state groundwater permit program requirements to the operation and closure of these stockpiles. The objective of this hydrologic assessment was to ascertain whether or not the WRS at the Ajo Mine have a reasonable probability of discharging potential pollutants to the underlying aquifer under the operational mine conditions. The hydrologic assessment was performed based on an evaluation of climatic data, prediction of the net infiltration rate through the WRS and prediction of additional hydrologic factors such as the time required to deplete available moisture storage in WRS. The predicted net infiltration rates ranging from 0.13 inches/year (1.1x10-8 cm/s) to 0.24 inches/year (1.9x10-8 cm/s) are below the threshold value of less than 10-7 cm/s recommended by Hutchison and Ellison (1992) as being characteristic of conditions that produce no or negligible quantities of seepage. In addition, the total time required to deplete available moisture storage within the Ajo Mine WRS and for any potential seepage from the WRS to reach the underlying aquifer is estimated to range from 260 years to 1,950 years. Collectively, the climatological and geotechnical investigations and the hydrologic predictions demonstrate that the WRS at the Ajo Mine hydrologically do not have a reasonable probability of discharging pollutants to the underlying aquifer. As a result of this prediction, the stockpile will not be regulated under the state groundwater permit program and operational and reclamation requirements will be limited to managing surface water runoff.

Jan 1, 2002

By COURTNEY DE KALB

IRON ore is the cause of the present trouble in Morocco. At least three nations are interested in the outcome and private syndicates have been active. The iron deposits are found in that mountainous northern coast line known as the Rif. This is an uplift that has been cut through, by the northward drainage, representing an ancient land surface. Erosion has produced .a fiordlike coast, which circum- stance has aided contraband' traffic to the tribes dominated by Abd-el-Krim, the chief of the clan of the Beni Urriaguel, near the center of 'the north coast, opposite Alhucemas. The iron deposits are extensive in the territory of the Beni Urriaguel. They were "located," if such a term is permissible, many years ago. The first arrangements, through direct contracts with the tribal chieftains, have been reinforced by compliance with the subsequent code under the Spanish protectorate in 1914. Under those terms, the location had to be made through the Arbitral Commission sitting in Paris. These locations, or "denouncements," were made by the I-louse of Mannesmann, of Hamburg.

Jan 1, 1925

By S Harvey

An inrush of water or mud into an underground mine, or sudden subsidence above mining voids represent low probability but high impact risks in underground mining. About two such incidents involving multiple fatalities or loss of production are reported each year worldwide. On average, Australia experiences one such incident every three to four years. This paper reports the development of a Standard that is intended to eliminate fatalities due to inrushes and subsidence.

Jan 1, 1998

By H. D. B. Wilson, W C. Brisbin

The Thompson-Moak Lake nickel belt lies along the root of a Precambrian mountain range of the island-arc or alpine type. This range coin-. cides with the boundary between the Superior and Churchill blocks of the Canadian Precambrian shield. The nickeliferous peridotites and nickel ores occur along a negative gravity strip, which also coincides with strong thrust faulting and the axis of greatest deformation of the mountain range. Similar structures and highly nickeliferous peridotites occur in present-day island arcs. Much of the belt is covered by Paleozoic rocks, but a length of 270 miles may be explored by present-day methods. Nickel deposits have been located along 60 miles of the belt. The length of the favorable structure and the size of the known deposits suggest that this will be one of the world's major nickel regions. The regional gravity anomalies, which consist of a branching negative strip bordered by two positive strips, are best explained by major warps of a crust consisting of a granitic and basaltic layer. The ore deposit

Jan 1, 1961

By Dale S. Preece

"The computer program DMC (Distinct Motion Code) [Taylor and Preece, 1989a] was developed in 1988 and 1989 to predict the motion of rock following a conventional blast. DMC executes very efficiently on a CRAY type computer due to the high degree of vectorization and also due to the use of spherical elements [TayIor and Preece, 1989b]. Bulking mechanisms developed specifically for use with spherical elements include rotation-induced dilatation and aspect ratio > 1.0 [Preece and Taylor, 19901. Rotation-induced dilatation allows the radius of the sphere to expand as a function ofsphere rotation to simulate the interaction of corners and sides of blocky rocks. An aspect ratio > 1.0 is achieved by kinematically tieing spheres together."

Jan 1, 1991

By J. C. Heter

Industrial Mineral Fillers, LLC. is in the initial stages of mining and processing Anorthosite (CASPAR TM) at its CASPAR mine located in Soledad Canyon, Los Angeles County, California The CASPAR is being mined from the Precambrian San Gabriel Anorthosite Complex of the western San Gabriel Mountains. Preliminary results suggest that CASPAR is a desirable alternative to silica sand used in construction applications, such as, stucco, grout, abrasives, and other uses including filtration and golf course recreation sands. With the use of standard ore dressing techniques, CASPAR is suitable for use as a filler in paint, plastics and rubber. Environmentally, CASPAR has advantages over silica sand, in that, there is no detectable Free Silca.

Jan 1, 1997

By E. Owens, R. Gudavalli, D. Wilder, T. Xia

As mechanical shock and vibration environments evolve, it is important to understand their potential effect on human operators. Human beings are sophisticated mechanisms comprised not only of passive components with mass, damping, and stiffness characteristics, but also of components that can actively affect apparent mass, stiffness, and damping. Because the lumbar spine can exhibit local, short-column buckling, stability of the human trunk depends on the responsiveness of the neuromuscular control system.1-2 We have been evaluating the ability of patients with back pain to respond to a series of sudden loads. We believe the results have implications for isolation design and standards development. Methods 153 patients, aged 21 to 55, presenting with back pain agreed to enroll in a research study that randomly assigned them to one of three treatment arms: high velocity low amplitude spinal manipulation, low velocity variable amplitude spinal manipulation, or wait for 2 weeks and then be randomized to one of the above groups. Response to sudden load testing was one of a battery of baseline evaluations performed upon entry into the study and prior to treatment. EMG electrodes were attached to the skin over the paraspinal muscles of the standing participant bilaterally 3 cm from midline at the L3 level. While standing upright on a force plate (Bertec), participants were fitted with a strap around their back and hooked to a load cell in front of their chest. An accelerometer was rigidly attached to the load cell. Impact was applied to the chest using a cord attached to a falling weight. The weight’s fall distance was varied between 9 and 13 inches to account for the size of the subject. The subject was blindfolded and wore headphones playing white noise to prevent cueing of when the weight was dropped to apply the load. Hence, although the participant knew a load was about to be applied, he or she did not know the instant it would occur. Just before the weight was dropped, a 4 second data collection process was started for the two EMG electrodes, load cell, accelerometer, and force plate. The load drop was repeated 6 times, at irregular intervals, over a period of 2 minutes. The raw data thus collected was reduced to obtain several values: 1) length of time from the pull on the harness to the beginning of the response of the left and right paraspinal muscles (LES, RES), 2) time and magnitude of the maximum response, 3) force and acceleration experienced at the chest, and 4) the time and magnitude of the center of pressure location (COP). A general linear model was used to evaluate the results. Results For the EMG data, of the 1,824 observations made, 90% of them indicated a response. Prior to the sudden load, resting muscle activity was different between left and right sides (p=0.0001) and between males and females (p=0.0001). Female subjects began to respond to the sudden load within 92 to 110 ms and males from 101 to 109 ms. Females exhibited more variation in starting

Jan 6, 2006

By Jeffrey M. Listak

The Bureau of Mines has conducted a rock mechanics study to monitor deformation of near-seam strata above a longwall panel in the Pittsburgh Coalbed. The primary goal was to determine the height of caving immediately behind advancing longwall face supports. This study, although site specific, provides information on the caving mechanism associated with longwall extractions so that strata behavior and its interaction with longwall face supports can be better understood. Two holes were drilled, approximately 550 ft apart along the center line of a longwall panel, from the surface to the coalbed approximately 650 ft below. Various downhole geotechnical instruments were used to monitor strata deformation. In addition, surface elevation surveys were conducted to differentiate between surface and subsurface activity. This report discusses the caving characteristics of the strata as the longwall panel approached and passed beneath the boreholes. Physical property data are also presented to demonstrate the relationship between caving behavior and local geology. Data show that immediate caving of strata above the longwall face occurred at a height less than 23.5 ft and that strata behavior above longwall extractions is highly dependent upon lithology, with major disturbances occurring at weak lithologic zones.

Jan 1, 1986

By Clayton M. Rumsey

In 1984, the U.S. Bureau of Mines conducted a mineral survey of a 26,598-acre study area which includes the 23,702-acre Mt. Limbo Wilderness Study Area (NV-020-201). The study area is 65 miles northeast of Reno, NV, and is underlain mainly by Cretaceous granodiorite that comprises the Selenite Range. Tertiary basalt, rhyolite, and sedimentary rock as well as Quaternary alluvium and lake deposits are exposed near the study area boundary. Mines just north of the area in the Hooker mining district produced tungsten ore in the 1940's and 1950?s. Similar deposits are not known in the study area. Disseminated gold is in sinter about 6 miles west of the study area and at several other locations regionally.

Jan 1, 1986

The stability of paste fill bulkheads forms an integral part of a successful paste fill system. Bulkheads are constructed at the draw points of open stopes to contain paste fill while the initial pour cures and forms a consolidated plug. Mobilization of uncured paste fill as a result of a bulkhead failure can lead to significant consequences, including endangering the safety of personnel, property damage and production losses and delays. The loading conditions in the paste fill and the resultant lateral loads on the bulkheads are complex and are dependent on many factors. This paper presents a case study of several paste fill bulkhead failures; the results of an in-situ pressure monitoring program to ascertain the pressure loads, and the subsequent paste fill bulkhead evaluation.

May 1, 2007

By K. L. Myers, R. Espell, C. Deringer

Construction of the AA Pad reclamation was completed in the fall of 2000. Seeding of the ET cover began in the late fall of 2000 and continued through May of 2001. On Saturday afternoon, June 1, 2002, a large, very localized thunderstorm struck the reclaimed AA Pad site. Eyewitnesses present at the time described a dark storm cloud parked above the site for less than half an hour. Average rainfall intensity was measured to be 122 mm (4.8 inches) per hour and peak rainfall intensity was estimated to be 213 mm (8.4 inches) to 259 mm(10.2 inches) per hour. At the time of the storm, the construction was less than two (2) years old and the vegetation had only a single season of growth. The entire period from the end of construction until the date of the storm was a drought period with below normal precipitation. Other than a few small snowmelt events, there was no precipitation event large enough to produce any significant flow in the channel network. Therefore, the very first significant runoff event was the extreme event of June 1, 2002. The storm essentially represents a large-scale field test of the design concepts used at the AA Pad site. Shortly after the storm, data was collected and analyzed with the intent of learning as much as possible about the performance of the cover system design with the expectation that the newly acquired knowledge might be utilized in future designs to further improve the performance of similar cover systems during extreme events.

Jan 1, 2003

By Otis M. Clarke

The Eufaula bauxite-kaolin district in southeastern Alabama is an important source of raw material for the refractory industries in the United States. At the present time, five companies are mining and processing bauxite and kaolin from this district and a sixth company is holding substantial reserves. Mining operations are expanding, but finding new ore reserves is a major problem. The Geological Survey of Alabama sponsored geologic research in the Eufaula district to: (1) investigate the

Jan 1, 1973

By John D. Godfrey

A brief account of economic developments in and around northeastern Alberta is presented and mention is made of mining and industrial developments currently of interest in the area. Planned and projected operations are briefly discussed for this region. The history of geological surveys and mining activities in the Shield area of Alberta and the adjoining parts of Northwest Territories and Saskatchewan is traced. Reassessment of the presently-known economic picture of northwestern Canada in conjunction with some recent information on Precambrian structures of northeastern Alberta points to some interesting mining possibilities, particularly in and around that province.

Jan 1, 1960

By Albert Ruiz

The 2,250-MW, coal-fired Navajo Generating Station located in Page, AZ draws water from Lake Powell using submersible pumps installed in five inclined shafts. Drought threatens to lower the reservoir to below the existing intakes. A system of new steel-lined intake shafts located on the same site was required for uninterrupted plant operation. The small size of the site, and the need to keep the existing system in operation, required detailed designs and placed significant limitations on construction equipment and activities. The Navajo Sandstone that forms the near vertical shoreline of the reservoir is 98 percent very fine grained quartz, highly abrasive and contains highly fractured intervals that presented numerous challenges to drilling the new 152-m (500-ft) deep, 109-cm (43-in.) diameter intake shafts inclined 23° to 26° from vertical. Spatial constraints, submersible pump design and operational criteria required that each shaft have a unique inclination and orientation and hit a small breakout target located 76 m (250 ft) under water. Sophisticated drilling equipment and techniques as well as state of the practice downhole survey technology and methods were used to make adjustments and maintain drilling accuracy with less than 1 percent deviation. Environmental requirements mandated water as the drilling fluid and grout was not allowed in to the lake under any circumstances. The shafts were videotaped and the breakout locations were examined using an underwater remotely operated vehicle (ROV) to verify shaft locations and rock conditions, and to guide placement of pneumatic packers to ensure grout did not transmit to the lake during the steel liner installation. In anticipation of the invasion of quagga mussels, the shaft design included an allowance for a chemical dosing system and a copper-rich alloy at the exposed portions of the steel liner.

Jan 1, 2011

By M. Rieber

The recent history of the mercury market results almost entirely from U.S. Government actions. Its derived demand has been curtailed by U.S.E.P.A. mandates; its supply has been augmented by U.S.D.L.A. controlled stockpile releases. The resultant prices have altered its market structure, impacted mercury mining, refiners and recyclers, and affected international production and markets. From a marketplace product mercury is rapidly becoming a disposal problem. Other minerals may follow in its wake. This paper reviews developments in demand, particularly in relation to environmental constraints. Supply side impacts are considered. The impact of stockpiles, both as a market overhang and as a potential supply is reviewed. Government stockpile disposal activity is emphasized, but the size, estimated disposal rate, and quality of the private stockpiles are considered, as is the potential availability of additional material from shut-in mines.

Jan 1, 1995

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

By John C. Machisak

This publication, for the calendar year 1959, contains statistical data on injuries and employment pertinent to metal mines, ore-dressing plants, and primary nonferrous smelters, refineries, and reduction plants. The Bureau of Mines is authorized to request data on injuries and employment in the metal-mining industry, and the information, voluntarily submitted by the operators, contributes immeasurably to the promotion of safety in the metal-mining industry. Every effort has been made to make the annual canvass as complete as possible. The data presented are classified according to the hind of ore mined and includes information on copper, iron, lead-zinc, gold-silver lode, placer, uranium- vanadium, and miscellaneous metals. A breakdown of miscellaneous metals by commodity is shown in tables 17 and 18.

Jan 1, 1963

By Edith Lafontaine

Modern underground mines operate fleets of mobile production equipment including drill jumbos, long-hole drills, load-haul-dump machines, trucks and bolters. Their availability has a substantial impact onto production cost and thus onto mine profitability. Through appropriate collection of pertinent data and information, use of adequate performance measures and their analyses, mine operators can identify the most promising and cost effective opportunities to get more from their equipment and to reduce the overall cost. This paper presents results of the study aimed to review and analyse means and measures used to quantify equipment availability and its contributing factors (reliability, maintainability and maintenance support) in several Canadian underground mines. It overviews current reporting procedures, sources, quality and quantity of the data and information collected as well as examines performance measures and their definitions used by the surveyed mines. Problems concerning data acquisition as well as meaningfulness and usefulness of the above mentioned metrics are also discussed. The paper concludes with some suggestions and recommendations concerning several aspects of equipment availability assessment. It is believed that the latter may become a more useful tool for mine operators in their efforts to reduce production cost than it seems to be the case at present.

May 1, 2007

By A Parbhakar-Fox, B G. Lottermoser

Management of solid mine wastes, particularly waste rock, requires careful planning to reduce the likelihood of sulfide oxidation, and generation of acid rock drainage (ARD). Waste management strategies must focus on obtaining a thorough understanding of the environmental characteristics of future waste rock materials. In this study, a waste management strategy for characterising underground waste rock was developed at a polymetallic underground mine in western Tasmania to determine which materials were appropriate for surficial placement. The criteria for surficial placement set by the regulator were that materials had to be non-acid forming and non-metalliferous. A range of cost-effective field-based tools, mineralogical assessments and mineral chemistry techniques were used on a suite of representative drill core material to determine an appropriate waste management strategy. Ultimately, a modified geochemistry–mineralogy–texture–geometallurgy (GMTG) approach was designed, whereby geoenvironmental focused logging and simple prescreening tools such as paste pH and sulfur analyses were used at stage-one; routine acid base accounting and leachate tests at stage-two; and validation tools including X-ray diffractometry and laser ablation inductively coupled plasma-mass spectrometry (ICPMS) at stage-three. This approach should be considered for other mine sites at early and operational life-of-mine stages with similar deposit characteristics, to ensure correct screening and placement of potentially hazardous waste materials in suitable above-ground waste repositories or mined-out mine sections.CITATION:Parbhakar-Fox, A and Lottermoser, B G, 2017. Effectively linking mining geology with waste management – a case study from western Tasmania, in Proceedings Tenth International Mining Geology Conference 2017, pp 117–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By R. P. Schneider

The Chino mine, concentrator, and smelter are located in Grant County in Southwestern New Mexico. Chino Mines Company is a partnership two-thirds owned and operated by Kennecott Santa Fe Corp., and one-third owned by MC Minerals Corp. (Mitsubishi) of Japan. The Chino Ore Body The Chino ore body is a widely varied deposit of rock types and contains intrusive stocks and sediments. The stocks contain chalcocite in a matrix of quartz, mica, and feldspar. Much of the feldspar is altered to clay. Some of these stocks are enriched with native copper. The sediments contain chalcopyrite associated with gangue minerals including magnetite, pyrite, garnet chlorite, and epidote. The contact of the stock and sediment is heavily altered to chlorite and clay. The stock ores contain economic quantities of molybdenite. The operating work index of Chino ore varies from 5 to 20 kwh/ton and averages 8.5 kwh/ton. The ore head to the concentrator averaged 0.81% copper and 0.010% molybdenum. Fifteen percent of the total copper head exists as nonsulfide mineralization.

Jan 1, 1985