Search Documents

By A. J. Rigby

Refractory linings in converters or anode furnaces used to over-oxidize the blister copper will suffer rapid deterioration, due to prolonged contact with copper oxide-rich slag. Nitrogen stirring with COP KIN porous plugs and use of SEMTECH OPC in converters and anode refining vessels can considerably reduce both refractory wear and processing times. In addition, careful control of the vessel atmosphere and the use of real-time optical process control minimize both slag volume and contact time with the vessel refractory.

Jan 1, 2005

By A. B. Hazar-Yoruç

Ferrochromium produced by smelting chromite ores is an important alloying component in the steel industry. Ore, coke and fluxes are mixed and reacted in an arc furnace for a smelting process of ferrochromium. In ad-dition to this process, pre-reduction of chromite ore with carbon is an important industrial process. In all these processes, the mechanism and kinetics of reduction of chromite with carbon play an important role. In this study, the reduction of Turkish chromite ore with carbon was investigated. Chromite and carbon were ground to three different particle size groups. Chromite was mixed with carbon in stoichiometric and excess ratios. The samples were reduced under argon atmosphere at temperatures between 1,200° and 1,350°C. The formed phases and alloy compositions of reduced chromite samples were analyzed by optical microscopy, scanning electron microscope (SEM) with EDAX and X-ray diffraction analysis (XRD). Experimental results showed that the degree of reduction and the reduction rate increased with increasing temperature and decreasing particle size. The highest degree of reduction, 61.4%, was obtained at 1,350°C. The reduction took place in three stages: Stage 1: transformation of Fe3+ to Fe2+ and formation of metallic nuclei, Stage 2: formation of metallic crust around the particles and Stage 3: growth of the metallic crust and coalescence of the metallic phase.

Jan 1, 2007

By B. W. Gandrud

This is the third report published by the Bureau of Mines concerning the washability of Black Creek coal. Both of the former reports.5/6/ dealt with the Black Creek coal at the Bradford mine, Dixiana, Ala., near the northeastern extremity of the Warrior field, whereas the present report is based on float-and-sink tests of coal from what is presumably the Black Creek bed near the southern extremity of the field. Although the Yolande Coal & Coke Co., owners of the property at Yolande No. 6 slope, consider this opening to be on the Black Creek bed, the authors do not feel that there is as yet positive proof that this correlation is correct. There has been little or no development of the Black Creek bed in the Yolande Basin in the past, and a positive identification of the bed at Yolande No. 6 will have to await further exploration and development. The Yolande No. 6 is an exploration slope 3/4 mile north of Rockcastle, Ala. The slope is approximately 400 feet from top to bottom on a dip of 180. As far as the authors can ascertain, coal has never been produced commercially from the Black Creek bed in the southwestern part of the Warrior field. Exploration work in the past has indicated that the Black Creek coal in this area is extremely friable and high in sulfur. Extreme friability would naturally discourage its use as a domestic and railroad fuel, and high sulfur content would be a disasvantage in its use for coking coal. The present study of this coal has been made with particular reference to sulfur elimination on the assumption that it would make a good coking coal provided enough of the sulfur could be eliminated by washing.

Jan 1, 1939

By David G. Adam

Introduction Syncrude Canada Ltd. is the operating company for a consortium of industry and government participants that produce synthetic crude oil from their leases in the Athabasca Oil Sands. Production from the $2.3 billion (1978) integrated mining, extraction, and bitumen upgrading and utility complex started in September 1978. Production is currently about 6.4 Mm3/a (40 million bbl per year) of high quality synthetic crude oil. This is done by upgrading the extracted bitumen from the oil sands mined. Plans are to increase the production to 8 Mm3/a (50 million bbl pier year) by 1989. At that time, the mining operation will be required to deliver 100 Mt/a (110 million stpy) of oil sand (ore) to the extraction plants, and handle quantities of waste ranging from 50 to 75 Mt/a (55 to 83 million stpy). The Syncrude plant is located at Mildred Lake, 40 km (25 miles) north of Fort McMurray and 480 km (300 miles) north of Edmonton, Alberta. Climate, particularly winter, is therefore a major factor affecting the design and operation of all the Syncrude production facilities. Bitumen production, consisting of overburden removal, oil/sand mining, bitumen extraction, and tailings disposal, account for about half the total SCO production costs. Considerable research and development, therefore, continues to be applied to improve both material handling and bitumen recovery methods. Potential applications for feeder breakers were identified in the material handling aspects of both overburden and oil sand mining to reduce cost and to attain planned production increments. Overburden removal Overburden materials on the leases comprise thin Pleistocene sands, gravel and fill, and sands, silts and clays of the thicker Clearwater Formation with the silt to clay components predominating. The latter contains multiple leases of hard siltstone with unconfined compressive strengths up to 148 MPa and thicknesses up 0.1 to 0.9 m (1 to 3ft). Characteristics of the overburden as well as the climatic environment and scale of operation present unique problems for the efficient removal of the material. In a bucketwheel/conveyor system, the weak silty clay formations require relatively flat working slopes for safe operation, while the siltstone lenses and frozen overburden require blasting or selective removal by other equipment. These factors, combined with the normal bucketwheel/conveyor design parameters, lead to high capital investment and relatively inefficient use of that capital. Hydraulic mining alternatives, including dredging, are constrained by severe clay settling problems in the waste disposal

Jan 6, 1986

The Penetrating Cone Fracture (PCF) technology 1 is a new method of rock excavation developed by Sunburst Excavation, Inc. of Denver, Colorado. PCF is a rock excavation method which employs tensile breakage mechanisms under controlled conditions to enable the continuous excavation of rock?in underground and some surface applications. The technology has developed rapidly over the last two years to the point where it is now being prepared for commercial application in the mining and civil construction industries. The initial commercial application of PCF will be undertaken at the Perseverance Nickel Mine of Western Mining Corporation Limited in Western Australia beginning in May, 1994.

Jan 1, 1994

By Joseph Clare, Elizabeth Anderson, Mike McGinley, Ron Hines, Judy Cochran

The South Lake Union Pipelines contract for King County Wastewater Treatment Division and Seattle Public Utilities in Seattle, Washington included three 1.8 m (72-in)inside diameter microtunneled pipeline segments totaling about 793 m (2,600 lf).Tunnel alignments were within street right-of-way of heavily traveled urban roadways. Project challenges recognized in the design included: high groundwater levels; contaminated soil and groundwater; variable soil conditions, including fill; and timber piles and other obstructions remaining from historic land uses. The tunnels were built using a Lovat MTS Microtunneling machine, beginning in spring 2003. Conditions encountered during construction presented additional challenges beyond those anticipated in the design process, and were successfully addressed by the owners, designer, and construction management consultant all working with the contractor. Problems included highly variable soil conditions, cracking of reinforced concrete pipe joints during pipe jacking, a timber pile trestle uncovered during shaft construction, and obstructions encountered in the second and third microtunnel runs.

Jan 1, 2005

By L. Adler

Two basic cases involved in the design of an opening in bedded rock are: 1) where the beds deflect from each other so as to be separated; and 2) where the beds deflect onto their lower neighbor, loading the latter while reducing their own load. Analysis of case 1 is relatively simple, while the interference of the original deflection curves in case 2 complicates analysis of the latter. Figures and formulae are presented for determination of interference loading in this situation. The design of an opening in bedded rock involves two basic alternatives.1'2 In one case the beds deflect away from each other, so as to be separated from their neighbors; in the other case the beds deflect onto their lower neighbor, loading it, while reducing their own load. This is shown in Fig. 1. The first case lends itself to a simple analysis, since the upper and lower boundaries of each beam remain a free surface. In the latter case, however, due to the interference of original deflection curves, the analysis is more complex. Earlier investigators of this interference problem solved it by making the tacit assumption that this type of loading was uniformly distributed along the beam's length. While there is no intuitive justification for this assumption, its use does lead to an approximate solution. Still, a more exact solution does not require this apparently unrealistic restriction. To achieve initial simplicity, the analysis will at first be limited to a two-bedded sequence, as in Fig. 2. Since both beams have identical end conditions and spans, the original deflections of their center lines are members of the same family of curves, as shown in Fig. 3. Therefore, if interference occurs at one point along their center lines, it will occur at every point. For convenience, the midspan point is that usually examined. Deflection at midspan for a uniformly loaded beam regardless of end conditions is: where c is a constant depending on end conditions; w is the body load and equals yh, lb per ft; y is the specific weight of rock, lb per ft'; L is the span, ft; E is Young's Modulus, lb per ft2; I is moment of inertia (for a rectangular section), I = bh3/12 = h3/12, (ft4); b is the width of beam and equals one; and h is the thickness of beam, ft; or 3U > yB an Substituting the appropriate values into Eq. lb, interference between the two beds can be predicted. Should it occur, the additional loads along the lower boundary of the upper bed and the upper boundary of the lower bed must be determined. From the principle of action and reaction, these added loads are known to be equal and opposite, as indicated in Fig. 4. Since the final deflection curves for both beds are identical (Fig. 3), their successive derivatives of y with respect tox must also be identical. That is:

Jan 1, 1961

By C. Perez-Rosales

A simplified method for evaluating specific surface of porous media is described. The theory takes as its point of departure a previous statistical method. Due to its simplicity, it is considered that the proposed method has certain advantages over methods currently used. By making some simplifications, the procedure for estimating specific surface is reduced to superposing, on an enlarged reproduction of a section of the sample to be analyzed, an evenly spaced grid and counting the number of intersections of the grid lines with the perimeter of pores. An indirect test of the theory is presented and the advantages of the method are discussed. INTRODUCTION The specific surface of a porous medium, defined as the surface area of the pores per unit bulk volume, is an important parameter with regard to flow of fluids through porous materials. In particular, it has long been recognized that specific surface is closely related to permeability. Since the internal surface of any porous material is extremely complex, the measurement of specific surface can only be accomplished by indirect means. It is considered that the best method' in current use for determining specific surface is the statistical method of Chalkley, Cornfield and Parka who originally applied it for estimating volume-surface ratios of morphologic components, such as cells or nuclei. This method will be outlined later. A method which has been used extensively in determining specific surface is based on the adsorption of a vapor by the internal surface of porous media. However, this method does not yield the surface pertinent to fluid flow, since it includes the tiny molecular interstices which do not influence the permeability of the porous material.' This method has been employed by Brooks and Purcell measure internal surface area of sedimentary rocks. The Kozeny equation, which relates the specific surface to the permeability of a porous medium, has found wide use in determination of specific surface. However, the KOzeny equation is not strictly correct. Large discrepancies have been found between theory and experiments.' Consequently. the specific surface estimated by this method is subject to serious uncertainties. Finally, there are other methods for specific surface measurements which are based upon a variety of physical and chemical properties: the heat conduction by a gas, ionic adsorption phenomena and direct chemical reactions of the surface with other substances. This paper describes a simplified statistical method for determining specific surface of porous materials. It is considered that, due to its simplicity, it has certain advantages over the methods presently used. For its validity, it is required that the porous structure of the material under study be of a spatially random nature. This is not a serious limitation since the naturally occurring porous media have this characteristic. THEORY The method proposed in this paper takes as its point of departure the interesting result obtained by Chalkley et al The method shows that if a line of length r is dropped repeatedly at random over a section of a porous medium, and counts are made of the number of times the two end points fall within pore areas (denoted by h for "hits") and the number of times the line intersects the perimeter of pores (denoted by c for "cuts"), then in a very large number of throws where S is the internal surface of the sample (surface of pores) and V, the volume of the pores (Fig. 1). Since the specific surface S, and the porosity 4 are given, respectively, by S. = Sl V, and 4 = V,l V,, where V, is the total volume of the sample, it follows from Eq. 1

By Oren C. Baptist

[Several new oilfields have been developed in northwestern Wyoming during the past 10 years, production is obtained from discontinuous, permeable sands enclosed within impermeable shales. The energy to drive the oil to producing wells in supplied by gas in solution in the oil. Most of the wells had high-initial potentials, but rates of oil production have steadily declined, indicating a dissipation of the driving energy and the possibility that large volumes of oil will remain unrecovered in the reservoirs. The studies reported in this paper were undertaken to develop laboratory data of the type most likely to be needed by persons studying the susceptibility of the Newcastle sand reservoir to secondary-recovery methods.]

Jan 1, 1957

By H. C. Rickaby

Introduction The township of Swayze, from which the Swayze gold area derives its name, is in the Sudbury mining division, approximately 150 miles northwest of Sudbury. The gold area may be regarded as situated at the southwest corner of a triangular area whose northeast and southeast corners are at Porcupine and Shiningtree, respectively, and whose sides are between 70 miles and 90 miles in length. On a geological map, it would be found that belts of Keewatin greenstones and sediments form the sides of this triangle, and that they surround a large granite mass. Prior to the summer of 1931 the Swayze corner of this triangle had probably been less prospected than the other parts and comparatively little was known of it from the standpoint of gold mining possibilities. The extensive belts of iron formation to the south and west of Swayze received some attention about the year 1909, and during the years 1927 and 1928 some prospecting was done in the townships of Greenlaw and Cunningham, south of Swayze, but chiefly for base-metals- copper, zinc, and lead. In the summer of 1931 a very promising discovery of gold-bearing quartz was made by J. G. and J. L. Kenty, working for the Brett-Trethewey Mines, Ltd., in association with Northern Canada Mining Corporation, and Northland Prospectors, Ltd., and this property, now known as the Kenty Gold Mines, Ltd., has been actively developed with very encouraging results. Following this discovery a6d during the summer of 1932 much prospecting took place in the area, as a result of which a number of other discoveries of gold were made, chiefly to the west of the original find. They are distributed over a wide area, which includes the townships of Rollo, Raney, Swayze, Denyes, Halcrow, and Greenlaw.

Jan 1, 1933

By Jean R. Garcia, Paulo J. R. Albuquerque, Renato P. Cunha, Osvaldo Freitas Neto

"Abstract Results obtained from in-situ load tests carried out on drilled displacement piles sunk in a porous, lateritic and unsaturated soil deposit, are analyzed in this paper. Three slow-maintained load tests were performed on deep instrumented piles with a diameter of 0.37 m and around 12 m long. The soil deposit consists of a superficial, silty clay “porous” layer 6 m thick, with an average standard penetration blow count (NSPT) of 4 and cone tip resistance and sleeve friction (qc and fs) of 1.5 MPa and 48 kPa, respectively. Under this layer there is a residual stratum 10 m thick, geotechnically consisting of a “porous” clayey silt with an average NSPT of 7 and qc and fs of 2.4 MPa and 202 kPa, respectively. The water table was reached at a depth of 17 m below ground level. The results of the field load tests yielded a maximum pile load (average for the tests) of 1428 kN, which is twice as high as corresponding experimental values from standard bored piles with similar geometric conditions. Exhumation of one of the tested piles was carried out after the test, in order to check integrity and shaft conditions. Numerical finite element analyses, using the commercially available French Code LCPC Cesar®, were performed in order to back-analyze the geotechnical soil parameters for a post execution pile condition. The results permitted a better understanding of the improvement of the subsoil given the intrinsic execution characteristics of this particular pile. It was also possible to note that drilled displacement piles have great potential to become an economically viable solution in tropical soils, given the enhanced behavior of such piles when compared to alternative (cheaper) techniques. In fact, it has several advantages which should make it a key foundation type in the Brazilian market in the future.IntroductionMost buildings in tropical soils use, as the main type of foundation, deep bored or auger type piles. These types of foundations can be performed in various ways, for example with or without soil extraction, with or without bentonite mud and so on. Two main processes maybe formulated: the first execution process is typified by bored pile types, continuous flight auger piles etc., which do not cause excessive soil displacement during excavation. With respect to the second process, one could mention, amongst others, driven piles (precast concrete or steel), Franki piles and drilled displacement piles, which do displace the soil during excavation by pushing the soil laterally around the hole in order to allow either the penetration of the pile or the excavator auger."

Jan 1, 2014

By M Ozkayhan, N Arslan

"The Efemçukuru underground mine in western Turkey is an intermediate sulfidation, epithermal gold deposit. The bulk of the mineral resources and all of the mineral reserves lie within the Kestanebeleni (KB) vein system. This system comprises four spatially-distinct mineralised zones: the south ore shoot (SOS), the middle ore shoot (MOS), the north ore shoot (NOS) and the KB north-west ore shoot. Production currently occurs only in the SOS, MOS and NOS zones. The gold mineralisation is very fine grained and occurs as free grains in quartz and carbonate, and as inclusions in sulfide minerals. Gold is recovered as part of a sulfide concentrate by flotation methods. Though hosted in the KB vein, the gold mineralisation is not evenly distributed within the veins. Definition of its occurrence is totally dependent on diamond drilling.Diamond drilling at Efemçukuru is done with its own equipment and staff, all managed by the mine geology group. The process over the mine’s six year production history incorporates continual improvement with an innovative approach by focusing on the following: drill team organisation career development and training product research and effective equipment management cost reduction planning and scheduling of development for drill stations.Over 40 000 metres of mostly BQ size core are drilled annually by three drill rigs at a cost approaching US$35/m.The planning and execution of the drilling pattern depends on the configuration of the ore shoot and the planned mining method. Ore extraction is mainly by drift and fill mining augmented by about 15 per cent longhole stoping. The drilling of a specific area is scheduled to be finished 3 to 8 months prior to mining. This scheduling is sufficient for short-term grade model updates and any needed changes to the planned development or stope sequencing prior to planned production from the stope area.CITATION:Arslan, N and Ozkayhan, M, 2017. Diamond drilling at Efemçukuru gold mine, Turkey – a case study on the benefits of timely and cost-effective drilling to short-term planning, in Proceedings Tenth International Mining Geology Conference 2017, pp 285–290 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 20, 2017

By F. Habashi

Asbestos, an extremely useful natural resource, has been studied extensively mineralogically and for industrial application. Its extraction from ores has been greatly improved with respect to safety in the work place. In spite of that, there is a decisive effort in many countries to ban its use on the grounds that it is a toxic substance. This action resulting in drastic decrease in production and the possibility of destroying the industry. The chelation of asbestos with organic dyes seems to be a promising way to abate its toxicity. Dyeing can be done when the fibers are slurred in water at ambient conditions in the same way as textile fibers.

Jan 1, 2009

By A. Hekmat-Ardakan

Conventional hypereutectic Al-Si alloys such as A390 are used principally for the casting of components used in wear applications requiring abrasive resistance such as in engine or compressor blocks. A comprehensive study was undertaken to investigate the potential of improving the mechanical properties of these alloys by the addition of magnesium. A thorough thermodynamic study of the effect of the addition of Mg to the conventional A390 alloy showed that Mg2Si starts to form as a primary phase at 4.2% Mg as well as in the products of the binary and ternary eutectic reactions forming the matrix. Experiments were carried out in producing castings with different cooling and solidification rates of alloys with up to 10% Mg. Mg additions were found to increase the hardness over the as cast alloy due to solid solution strengthening. Also, T6 heat treatment greatly improved the tensile properties of these alloy compositions due to the strengthening effect of the theta-Al2Cu phase. The elongation of these alloys generally decreases marginally with Mg content. The most significant property improvement of the alloys with higher Mg content is the substantial increase in wear resistance. This is attributed to the dispersion of smaller particles of Mg2Si and their coherence with the matrix as compared to the large Si particles in the conventional alloy. A new rheoforming process for A390 is presented that improves the processing of the semi-solid slurry. Structure modification elements were also added to refine the primary and eutectic silicon greatly improving the processing of the semi-solid slurry.

Jan 1, 2011

By Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health?s (NIOSH) Spokane Research Laboratory are developing a borehole profilometer to dynamically measure the roughness pro-file of boreholes used to install roof bolts fully encapsulated with resin. Numerical measures of roughness were calculated from profiles of borehole surface roughness to determine potential roof bolt anchorage capacity. The concept of dynamically profiling was proven through the following series of laboratory tests: a sensitiv-ity test using various grits of sandpaper, a known-profile test along a section of a concrete hole, and a simulated borehole test in a pipe with machined grooves. Two profilometer prototypes were devel-oped that measure slight changes in the radius of a borehole using either strain-gauged, spring-steel arms or rigid, steel arms attached to a spring-loaded cone and a linear potentiometer. Both instruments performed reasonably well in the laboratory and were subsequently tested in boreholes drilled in two concrete blocks using different drilling techniques to obtain three different borehole surface roughnesses. A Z2 roughness parameter was calculated with data from the first profilometer, and an average radial increment was calculated from the test results of the second profilometer. Although both instruments were able to readily distinguish the difference between smooth and rough boreholes, the correlation coefficient (r2) for a linear relationship between Z2 and average radial increment was 0.577. Pull tests were conducted with resin bolts installed in the concrete blocks, but maximum pull-out strength could not be correlated to borehole roughness because in each of these tests, failure occurred at the resin-bolt interface. A more sophisticated prototype has been designed to measure surface roughness and also accurately determine the location and tilt of the instrument in the borehole. However, this instrument has not yet been fabricated or tested.

Jan 1, 2007

By William H. Shockley

There was an extensive mining and industrial exploitation of Russia, about 20 years ago, by Belgian, French and British capitalists; but the results were discouraging. It is said that the Belgian and French public together lost approximately $400,000,000, chiefly in the coal and iron industry of southern Russia. This loss is largely accounted for by the fact that most of the companies were formed, as usual in " boom" times, to sell stock; and that thorough investigations were not made. I11 1906, renewed interest was taken in Russian mines, especially in those of gold and copper, and a considerable literature is growing on this subject; but as yet I have seen no account of one of the large Russian mining estates. The following notes on such property, where the conditions are so different from those in the mining regions of the United States, should be of interest: This inadequate and probably somewhat inaccurate account is made up, partly from my own notes made on the ground, in the summers of 1904 and 1905, and partly from a volume on the geology and resources of the estate issued several years ago, containing surface- and mine-maps, and from a pamphlet published in 1904, giving a general account of the condition and prospects of the property. This pamphlet includes a report made in 1899 by Arthur L. Pearse, a member of this Institute. Both these books are in Russian, and were prepared by the Bogoslovsk Mining Co., which owns and operates the property. Articles in many other languages have appeared dealing with various matters connected with the estate; but I know of no other general account of it. In numerous books and articles on the Urals and Siberia, however, localities are described in which somewhat similar conditions prevail. Recent papers by

Jan 1, 1909

By T. Alboussiere, O. Paireau

"We have designed an experiment to simulate natural convection in a direct-chill aluminium ingot. In this experiment we induce natural convection within a hemisphere filled with liquid-metal (mercury). The device consists of a copper hemispherical bowl closed by a copper plate. The top is maintained at superheat temperature while the boundary is cooled. While the temperature measurements were found using thermocouples, the velocities were obtained using an original technical procedure that relies on MHD properties. By applying a steady local magnetic field, we measure the velocity. The distribution of temperature and velocity can be separated into a thermally stratified core bounded by thermal wall jets. These wall jets greatly influence the degree of macrosegregation in ingots.1. Natural Convection in Aluminium CastingIt is well known that the quality of the final product in aluminium casting depends on the movements within the liquid metal such as forced or thermogravitational convection. Strong buoyancy-driven flows are known to occur in the liquid metal pool of an aluminium ingot caster. These flows have a significant influence on the metallurgical structure of the ingot through the redistribution of heat, fragmented dendrites and segregated material within the pool. Macrosegregation mechanisms depend on favourable temperature and flow distributions in the sump, and these factors will determine the pattern and degree of macrosegregation. Moreover, for many years, the importance of thermally-driven natural convection in casting has been underlined (Cole & Bolling, 1965). In this way, a precise determination of the velocity and temperature fields is required in order to improve understanding of the macrosegregation mechanisms. That is precisely the aim of this paper, which provides experimental data of the flow and the temperature distributions in a natural convection experiment. We intend, with this laboratory experiment, to determine accurately the velocity field, particularly within the thermal boundary layer where the effects of the flows may have an important role in the transport of crystals."

Jan 1, 1999

By M. Kalin

"Ecological Engineering and Biological Polishing technology is a decommissioning approach for inactive coal, uranium and base metal operations. To improve acid mine drainage water some fundamental aspects of wetland ecology and sediment microbiology are combined, to provide conditions to allow for biomineralization of the contaminants.This paper summarizes the first records of microbial alkalinity generation in acid mine drainage through the utilisation of the ARUM process. The process requires that the seepage is at pH 4.5 where sulphate reducers utilize sulphate to produce hydrogen sulphide, which in turn precipitates with metals. The pH increase is brought about by alkalinity generating microbes.The ARUM process has been successful in increasing the pH from 2.5 to 7.0. Flow through reactors operated in the laboratory continuously for more than 60 days have removed Ni from 13 mg/L to < 0.01 mg/L. Design parameters are being developed for low flow rates of 5 L/min in a test system receiving seepage from a tailings.1.0 INTRODUCTIONAcid mine drainage associated with mining wastes poses a significant environmental problem. Conventional means to treat acid mine drainage (AMD) use chemical treatment system. Ecological Engineering technology uses natural biological means to curtail and ameliorate AMD during mine operations and at the time of decommissioning. The premise underlying Ecological Engineering technology is that AMD is the result of a natural process enhanced by mining activities. Therefore, in nature, a process providing a natural balance to AMD has to exist, which, when assisted through appropriate means, can counteract the detrimental effects of AMD on the environment. This process is microbial alkalinity generation which is known to occur in wetlands, lake and ocean sediments (Baas Becling et al, 1960)."

Jan 1, 1991

By O. E. Kiessling

A GROWING uneasiness in the oil fields indicates that doubts are arising as to the efficiency of the present technical, economic and legal arrangements affecting production. Recent documents of the federal government, debates in state legislatures, editorials in the daily press and statements of oil company executives re-echo the notion that the present methods of producing oil satisfy neither the business man nor the public. Such intimations are of utmost importance, since oil is a vital clement in modern industry and dependence upon it increases as new uses develop. SECTION I-PRESENT SCHEME OF COMPETITIVE EXPLOITATION IS WASTEFUL The oil industry has convinced itself, for very good reasons, that the present scheme of competitive exploitation results in losses, both in terms of quantities of oil and in terms of profits. The story of these losses is familiar enough, and it is necessary only to distinguish and summarize briefly certain factors that are of importance to the following argument. Oil pools are exploited under a competitive economic system based on private ownership and contract; the hope of profits attracts capital and enterprise, and competition is supposed to serve as a regulative factor. Whether such a scheme of industrial organization works is partially dependent on the ability of the producer to withhold or produce is commodity as he sees fit, in accordance with the dictates of market demand.

Jan 1, 1927

By C. P. Bowie

During the period of 10 years from January 1, 1908, to January 1, 1918, approximately 12,850,000 barrels of oil and 5,024,506,000 cubic feet of gas were destroyed by fire in the United States, entailing a total estimated property loss of $25,254,200. During this period 503 fires were reported. As is shown in Plates I and II, 310 of these fires were caused by lightning and 193 by all other causes. The losses from the fires caused by lightning were estimated to be $11, 148,000, and from those due to all other causes $14,106,200. Directly and indirectly, the fires resulted in the deaths of nearly 150 persons and were responsible for almost as many more being permanently disabled. For the past three years the Bureau of Mines has been conducting investigations to determine the nature and the specific causes of these fires, with a view to suggesting means whereby they may be suc- cessfully combatted and, in some places, perhaps eliminated entirely. As the subject of oil and gas fires is necessarily broad, no attempt is made in this bulletin to treat it exhaustively; rather the bulletin aims to point out what has been done by operators in the past, and to describe various fire-prevention methods and fire-fighting appa- ratus which are being used or adopted by many of the larger oil companies. These methods and apparatus, it is believed, if uni- versally employed by operators, will largely decrease the present enormous annual losses. In the discussion of oil-well fires, the methods used in extinguishing several of the larger and more perplexing ones are described. As the right procedure for extinguishing any oil-well fire must be de- termined largely by local conditions, it is not probable that all of the methods used at some one fire, as described, will be applicable to a future fire. However, the operator, from these descriptions, may at least gain suggestions that will greatly assist him in fighting similar fires.

Jan 1, 1919