Search Documents

By S. C. Oliphant, R. Floyd Farris

Presented in this paper is a summary of the results of experiments conducted in both the laboratory and the field during the past three years in connection with casing-perfora. tion problems. Included are studies of gun features that influence bullet performance and penetration, and studies of the effect of perforator bullets on casing and the neat cement in the annulus. Discussion and data are also presented relative to the accuracy of depth measurements in deep wells. Introduction It is a common practice in the oil industry to effect the completion of oil wells by setting and cementing casing through the producing horizons and perforating the section of casing opposite the desired interval by means of a gun lowered into the well on a cable or on the tubing. This practice has been followed for some time, and this method of completion has been given considerable study by the companies that render perforating service as well as by the oil companies that utilize their services. Through continued research on this subject, it has been possible to develop guns, bullets, and powder that will permit controlled firing at great depths, and penetration of as many as two strings of casing. It is the object of this paper to present the results of studies made of gun perforating in both the field and the laboratory. These studies were made to determine the factors that affect penetration of the bullet, burring of the casing, accuracy of depth measurements, and other items. It is hoped that by presenting the results of these investigations a better understanding may be obtained of certain of the factors involved in gun perforating and further investigation of the subject will be prompted. Subsurface Tests A well approximately 9000 ft deep, which was being prepared for abandonment, was selected for subsurface tests of gun-perforating experiments, In preparing the well for the experiment, 51/2-in. casing in the hole was pulled and racked in the derrick. A test section of pipe, which consisted of 65 ft of 5-in. 18-lb J-55 casing centered inside 7-in. 28-lb N-80 casing, was placed in the derrick corner and the annulus between the two pipes was cemented from the bottom up with 161/2 lb per gal neat cement, which was mixed and displaced with a cementing truck in the usual manner. After the cement had been allowed to harden for about a week, the test section was lowered into the hole on the 51/2-in. casing to a depth of 6600 ft by casing measurements. The hole was filled with drilling fluid weighing 10 lb per gallon. A perforating company was called to perforate the pipe, but was not advised that an experiment was being conducted. The company was asked to check the total depth (to cross pins in the bottom of the test section), then to raise the gun a given distance and fire a given number of shots with 1/2-in. bullets, pick up another distance and fire a given number of 3/8-in

Jan 1, 1947

Estimation of local recoveries is an important issue in a selective mining operation. Two techniques, probability kriging and multigaussian kriging, are applied to estimate local recoveries at Jerritt Canyon. The pros and cons of each method are discussed in light of the results. Both methods provide simple and satisfactory solutions to the problem of estimating local recoveries. Consequently, they can be useful tools to work with in a selective mining operation.

Jan 1, 1986

By George A. Morgan

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East. Downstream processing of these mineral fuels to petrochemicals and fertilizers is a major investment opportunity. In 1991, the 15 countries that constituted the region accounted for 26 % of world crude petroleum output, 15.3 % of world natural gas plant liquid production, and 4.5 % of world dry natural gas production. Only Cyprus and Lebanon were not crude petroleum producers. Production of these mineral fuels all declined from that of 1990 owing to the Persian Gulf War, during which output from Kuwait and Iraq either ceased owing to war damage, or was embargoed. Prior to the war, Iraq and Kuwait were the fourth and fifth largest world producers of crude petroleum, respectively. In the war, virtually all of Kuwait's production and transport facilities were destroyed or damaged. Iraq's output was embargoed from export, with only domestic sales taking place. The embargo also affected Jordan, both in terms of transshipment of materials through it to Iraq and in exports of phosphate and potash. Shipments of crude petroleum by pipeline from Iraq through Saudi Arabia and Turkey and by vessel through the Persian Gulf were terminated. However, the loss in production from Iraq and Kuwait was made up by accelerated output from other Middle East and world producers. Saudi Arabia, in particular, with its excess production capacity, accounted for the largest portion, increasing crude petroleum output by 27 % to almost 3 billion barrels.

Jan 1, 1993

By Markus A. Reuter, Albert Scholte, Ewoud V. Verhoef, Gerard P. J. Dijkema

A dynamic, interactive map has been developed of the life cycle of a number of metals, from mining through to minerals processing, metal production, product manufacturing, recovery and waste management. Whilst the existing metal process network and waste management infrastructure provide substantial scope for (product) design, these also limit change due to the complex interdependence of metals, both in production and recovery, and the strong path dependency of industry and infrastructure development. Therefore, models for dynamic simulation were constructed that allow the specification and evaluation of the metal process network and waste management infrastructure ‘products’ over a longer time span. The model has been constructed using a bottom-up approach, to enable assessment of the environmental aspects of metallurgy and to simulate changes in the system structure and technology, i.e. from reactor or individual process step up to integrated material cycles. The model comprises hierarchical mass balances and linear models of individual processes and sub-processes. Thus, at lower system aggregate levels an increasing level of technical detail is represented. Data reconciliation has been used literature data on process feed, products and residue composition to calculate representative and reliable split factors around each (sub-)process. World production figures on process capacity and recovery rates are be used to calculate the relative contribution of processes. The dynamic map is illustrated with a case on the introduction of lead-free solder.

Jan 1, 2003

By J. Willan

This paper addresses the problem of designing a destress blasting procedure to reduce the incidence of rockbursting in hard rock mines. A review is made of the developed theory and practice of destress blasting in rockburst-prone ground. Specific reference is made to a recent survey of past and current practice with particular reference to Ontario mining operations. The need is identified for a more scientific basis for destress blast design and monitoring. Reference to developments in blasting technology as well as rock mechanics are then made to support a proposed, integrated design procedure and research strategy.

Jan 1, 1984

By M Hawkins

The Clem Jones Tunnel (formally known as the North-South Bypass Tunnel), a A$2.88 billion road tunnel project in Brisbane, Queensland, was successfully completed almost seven months ahead of schedule. The project included two parallel 4.7 km long road tunnels, 740 m of intermediate roadway access ramps and two auxiliary ventilation tunnels. The tunnels incorporate intelligent tunnel systems, best practice fire and life safety standards and typical civil tunnel elements.Over the duration of the project the Parsons Brinckerhoff (PB) and AECOM (formally Maunsell) design joint venture (MPB) were Lead Designers to the Leighton Contractors and Baulderstone Bilfinger Berger Joint Venture (LBBJV). Construction of the toll road commenced in September 2006 and was completed in March 2010, with the tunnel opening then. Contributing to the success of this project was the continued support the lead designers gave throughout the construction period.This paper will focus on some of the structural elements that contributed to the success of the project – in particular the cable tunnel structure, a small precast, culvert shaped element under the pavement of the mainline tunnel, and the fit-out of the Gibbon Street shaft which were designed to be constructed in a combination of precast and in situ concrete.The cable tunnel was incorporated early in the design phase and runs the length of much of the tunnel. This paper will outline the challenges faced by the designers with implementing this system which provided significant construction advantages, among which were being able to install a separate ventilation duct during construction and to start fitting out the mechanical and electrical conduits and drainage system while tunnelling was still underway.The Gibbon Street shaft had a length and width of 20 m by 40 m and an overall depth of 38 m. A 20 m high structure of precast and in situ concrete was constructed in the base to accommodate mechanical and electrical equipment and provide a take-off access for the southern ventilation tunnel. The construction purpose for this structure was to provide a junction between the tunnel boring machine (TBM) and the roadheader-style tunnels, a staging platform for commencing the roadheader tunnelling, and a platform where the TBMs could be dismantled and removed.The design was assessed and reviewed many times throughout the construction process to address the needs of each of these stages. Innovative use of precast concrete was used to minimise construction time.Additionally, the designers provided support to the construction team from the time of design completion through to the tunnel opening. This meant that the changes to the design and adjustment of construction loadings could also be assessed. The fi nal outcome resulted in an efficient construction sequence and a project that has provided an excellent outcome for the client, stakeholders and community.

Mar 8, 2011

By A. Henchiri, G. A. Gruber

INTRODUCTION Phosphatic resources may be quantified in terms of ore tons and phosphate analyses; however, to quantify phosphate reserves it is necessary to estimate the tons and quality of phosphate rock that can be extracted from the ore. The yield and grade of phosphate rock that can recovered from sedimentary phosphate deposits are usually difficult to estimate because of variations in stratigraphy and/or mineralogy. Prospecting phosphorite ores for purposes of estimating reserves and preparing mine plans requires considerably more effort than defining ore thickness and P205 content. In Florida, for example, it is standard practice to prospect by core drilling and to subject each strata (split) to beneficiation testing, and to perform detailed chemical analyses on the beneficiated products from each strata. For a completed drilling pattern the area of influence of each hole is 2.5 acres. The number of strata per drill hole typically varies from two to five, and thus complete prospecting of a 40acre tract requires drilling 16 core holes and beneficiation testing of about 48 ore samples. Florida practice is not appropriate for all phosphorite deposits. Functional drill rigs and trained drillers may not be readily available. Water for core drilling may be unavailable and the characteristics of either the overburden or ore may require careful attention and excessive cost to obtain representative core samples. Alternate ore sampling methods include auger drilling, rotary drilling to obtain cuttings, and the excavation of trenches, pits, and shafts. Drill cuttings samples are generally the least expensive to obtain, but they are usually unsuitable for beneficiation testing because of particle size reduction during drilling. Ore samples from surface trenches and pits are expensive and may not be representative of deeper ore. Ore samples from shafts are the most expensive to obtain, but if taken properly they are reliable for use in laboratory and pilot plant testing. Regardless of the prospecting technique used, reliable estimates of the yield and grade of phosphate rock that can be extracted from an ore deposit are required: • to justify capital expenditures for a new mine • for mine design and mine planning • for beneficiation plant design • for production forecasts, quality control, and marketing. This paper describes models that predict the beneficiation response of ores from three phosphate ore deposits. The purpose of these models is to obtain maximum utilization of available prospect data with the least cost. ORE DEPOSITS Simple beneficiation models have been developed for ores from three sedimentary phosphate deposits around the Mediterranean area. The first deposit, herein described as "A" ore, is located north of the Mediterranean Sea. The second deposit, designated as "B" ore, is located east of the Mediterranean Sea, while the third deposit, "C" ore, is located south of the Mediterranean Sea. Ore "C" is from the Sra Ouertane deposit in northwestern Tunisia.

Jan 1, 1993

By H. B. Fuqua, B. E. Thompson

For a very brief description of the North Texas area and the general geological features with which it is associated, the reader is referred to the summary for 1935. As in previous years, the authors have been unable to undertakc the almost impossible task of isolating statistics for the hundreds of productive "spots" which are included within the generally productive areas of the several counties. However, pools that appear to be definitely isolated—as, for example, the Foard County production and the new pool recently developed southeast of Gainesville in Cooke County—are covered separately. During the year 1936, both routine development in proven or scmi-proven areas and exploratory drilling showed a decrease over the year 1935, there having been a total of 1453 wells drilled in the district during 1936, as compared to 1619 in 1935. It is also of interest to note that abandonments exceeded completions in 1936. Developments during 1936 While a number of local productive spots were found in Wilbarger, Archer and Wichita Counties, and numerous minor local extensions to older producing areas were developed in practically all the producing countics in the district, only two discoveries of sufficient importance to justify special mention were made. Anderson and Kerr No. 1 Bruhlmeyer, about two miles southeast of Gainesville in Cooke County, was completed in April, at a total depth of 2014 ft., for an initial production of 315 bbl. daily from a sand of Pennsylvanian (Canyon) age. Development has been rapid and the field is about drilled up. During November the 100 wells in the field averaged about 40 bbl daily. The structure appears to be a small fold associated with the northeast flank of the main uplift, which extends in a northwest-southeast direction across Cooke and Montague Counties.

Jan 1, 1937

By Dorsey Lyon

I. INTRODUCTION. In presenting, this paper the writers wish to call attention first of all to the fact that the electric furnace was not developed as a competitor of the combustion furnace, but: 1. For the purpose of doing high-temperature work which it is not possible to do in the combustion furnace; and 2. For the treatment of ores from deposits which. are located in regions where fuel is scarce and costly, and where hydro-electric power is comparatively cheap, as is the case in Chili, in Canada, in certain parts of this country and Mexico.. This paper is not presented with the idea of trying to. prove that the electric furnace should replace the reverberatory or the blast furnace as used at present in the smelting of copper ores, but that it may be substituted for their in those localities which are not favorable to them,) and where either of the two following conditions may exist: (a) A district remote from railway transportation. facilities, and where there is a deposit, or deposits, containing sufficient values to warrant their being worked, but which, due to the cost of getting coke in for operating a smelter and of getting ore out to a smelter, have to remain unworked.. And where, on the other hand, there is plenty of water power which call he developed at reasonable cost for the production of electric power, by the use of which for. smelting the ores in an electric furnace, with subsequent Bessermerization if necessary, a concentrated product may be obtained, which can easily stand the necessary transportation charges. (b) Or,. comparatively speaking, the transportation facilities may be all right, but the cost of fuel be too great to permit of the ordinary methods of smelting, whereas,- on the other hand, hydro-electric power can he developed: in the district at a, low cost,, and the ores could be smelted by the electric furnace at a cost. that would make their treatment possible. With these possibilities in mind we have attempted to make a brief comparative study of the problem for the purpose of aiding those interested in the subject, in determining whether it would be possible metallurgically, and feasible commercially; to use the electric furnace-in those localities where, by reason: of excessive fuel costs, the cost, of operating the furnaces for smelting copper-ores. is either excessive or prohibitive. Although the smelting of copper ores in the electric furnace has received considerable attention and more or less experimental work has been done, so far as: we lire: aware there ate no electric furnaces in the United States which are' being worked on copper ores. In Norway, however, trial smeltings of copper ores with an electric furnace of 1,000 h. p. and an estimated producing' capacity of 2,000 tons per annum, have been

Jan 8, 1913

By Michael Chender

The current outlook for financing new copper production is not very encouraging. At a time when companies are slogging through a protracted period of low prices as well as having to accept lower profits due to more stringent tax and royalty schedules, banks are beginning to require companies to take a greater equity interest in new projects. Mineral resource financing, including copper, seems to have lost much of its appeal to the lending institutions, and loans of any kind to many of the developing countries -from which over half of new copper capacity could be expected to come-are being examined much more critically than they were in the late 1960's and early 1970's.

Jan 12, 1976

By Alastair C. Torrance

"A brief review of the Australian mining industry is given followed by a more detailed treatment of a study of the influence of primer Size on explosive performance. This is based on a joint research programme conducted by BHP Central Research Laboratories and Dyno Wesfarmers Ltd and examined the effect of the size of cast primers on the run up and steady state detonation velocitiesof ammonium nitrate based explosives as a function of blasthole diameter. The field trials examined a numter of the Dynamo 'Westfarmers HDF series of primers in conjunction with ANFO, emulsion and watergel explosives. Results indicate that the iun up velocity of 187 mm diameter ANFO charges is negligible using cast primers as small as 150g. However, emulsion and watergel explosives did exhibit run up in both 187 and 3:1mm diameter blastholes, independent of the size of primer. This could last from 7 to 10 blashole diameters"

Jan 1, 1991

By W. B. Boggs

The Noranda smelter was built by Noranda Mines, Limited, from the designs of A. E. Wheeler, consulting metallurgist, New York, for the reduction of ores and concentrates from the Horne mine, and to treat, on a custom basis, ores and concentrates from other mines in the Rouyn district. The smelter is situated at Noranda in western Quebec, about 330 miles directly north of Toronto. Ground was first broken for construction in November, 1925, before the completion of the branch railway into the district, which was not finished until October, 1926. After many difficulties and delays due to the Jack 'of transportation and the severe weather during the winter months, the smelter was started in December, 1927, and the first blister copper was poured on December 17th. The smelter was built throughout in two duplicate units, each with a rated capacity of 500 tons of ore per day. Operations were started with only one unit, and after several months it was found that one unit alone would smelt 1,000 tons of ore per day. At this time only one shaft, No. 3, existed, and its hoisting capacity and the capacity of the original crushing plant were insufficient to supply ore for two units at the increased tonnage. Accordingly No. 4 shaft was sunk and a new crushing plant provided to handle the ore hoisted there. This work was completed in the latter part of November, 1929, and since that time both smelter units have been operating.

Jan 1, 1930

By W. Scheetz

The Brewer Gold Mine is an open-pit, heap leach operation that processes about 122 kt/m (135,000 stpm). The mine is operated by Brewer Gold Inc., a subsidiary of Westmont Mining Inc., and is located near Jefferson, SC, about 80 km (50 miles) southeast of Charlotte, NC and 80 km (50 miles) northeast of Columbia, SC (Fig. 1). All of the ore to date has been produced from a breccia body of hydrothermal origin and a related smaller body of fault-controlled ore, known as the B-6. Reserves at the time the mine commenced production were 4.6 Mt (5.1 million st) grading 1.4 g/t (0.042 oz per st) gold. History Although some reports of a pre-Revolution War shaft at the Brewer are in the literature (Lieber, 1856, Nitze and Wilkens, 1897), gold was first produced in earnest from the Brewer Mine in 1828. Production occurred primarily from placer deposits south of the present mine workings. Lieber noted in 1856 that “every branch, gulch, ravine or even declivity of the main hill has been washed and rewashed.”

Jan 1, 1991

By C. J. Dungey

INTRODUCTION The County of Cornwall is situated in the South Western extremity of England, see Fig. 1, and has for hundreds of years been an historical centre of mining activity. In the last century many thousands of Cornish miners emigrated to Canada, U.S.A., Australia and numerous other countries throughout the world to form the nucleii of mining industries in those lands. At present there are four active underground mines within the county, all mining tin, together with a relatively large china clay industry. All the operations are directly or indirectly associated with the three main granite intrusions, namely the Land's End Granite, the Carnmenellis Granite and the Bodmin Moor Granite. The report which follows relates to two mines, owned by the South Crafty Group of Companies, namely the South Crofty Mine itself and its smaller subsidiary, Wheal Pendarves. Both these mines are adjacent to the Carn Brea Granite ridge, see Fig. 2, which is an off-shoot of the main Carnmenellis Granite mass. The Carn Brea Granite has provided one of the most intensive areas of copper and tin mineralisation anywhere in the world. Many of the mines worked during the last two centuries and the early part of this century were situated close to the metamorphic aureole surrounding the granite intrusion. Both South Crofty and Wheal Pendarves have their shafts collared in the overlying slate, locally known as killas, but the major part of their workings are in the granite beneath. The ore bodies, or lodes, of both mines are generally steeply dipping and approximately one to four metres in width. They have been, and continue to be, worked by either back or under-hand stoping with the major level interval being approximately 37 metres. A feature of both stoping systems is that they require no back filling and in many cases the completed working areas have remained open for many years due to the competent wall rock conditions. The stoping operation necessitates having box-holes or draw points at regular intervals along the strike length at 4 to 7 metres centres; thus a stope some 50 metres long may typically have ten box-holes or draw points through which air can percolate into the empty stopes above. The granite country rock contains traces of uranium minerals, namely pitchblende or uraninite, and it is the decay of this uranium mineral which leads to the formation of the mobile radon gas which, together with its short lived daughters, may create a hazard. The presence of uranium minerals has long been known, but the quantities being so minute, it was not appreciated until some ten to fifteen years ago that these might present a hazard. The Mines and Quarries Inspectorate approached Management approximately ten years ago with a view to taking samples in areas of the mine that they felt might contain the highest concentrations of radon. Samples were thus taken in several areas of both mines, normally well away from working areas and where there was no through ventilation. The results of these initial tests were published by the National Radiological Protection Board in a paper entitled "Radon and Its Daughters in Various British Mines". The results of the initial surveys made it apparent that improved ventilation was the most important factor in reducing radon daughter concentrations within the mine atmosphere, with increased flow rates having three beneficial functions, viz. (1) To dilute radon daughter concentrations. (2) To prevent radon and its daughters reaching a state of equilibrium. It is not uncommon for radon and its daughters to have a disequilibrium factor of 1,000 in some uranium mines.

Jan 1, 1981

By B. R. Stewart

The exclusion of coal fly ash from regulation as a hazardous waste has led to increased interest in returning ash to the coalfields for co-disposal. A multi-year column study used coal refuse with high potential acidity (4% total-S), and two alkaline ashes in various bulk-blends. The unamended refuse acidified rapidly, producing acidic (pH 1.7) leachates, high in dissolved metals. Treatments blended with sufficiently high amounts (20 to 33%) of alkaline ash produced alkaline (PH >8.4) leachates with low metal levels, while lower ash blending rates acidified over time to produce metalliferous leachates. Examination of solid materials indicated that pyrite oxidation was occurring to some extent in all treatments. A regression equation (r = 0.95) was developed to estimate time to net acid release for mixtures of these materials. Ash alkalinity and refuse potential acidity must be balanced to insure water quality for co-disposal environments, or the ash materials should be isolated away from acidic drainage waters.

Jan 1, 1997

By M. Gimpel, R. Galler, T. Antretter, H. Kargl, R. Tichy, W. Ecker, M. J. Mikl-Resch, G. Pittino

"A computational method based on a continuum-mechanical approach to simulate rock cutting is developed and evaluated. The aim is to obtain the local loading acting at the cutting pick during operation. The explicit FEM is chosen to model the pick-rock interaction. The presented method takes advantage of (i) an advanced material model (ii) a robust contact algorithm and (iii) fast calculations due to parallelization. A damage-plasticity law is chosen and modified with user-subroutines. A user integrated element deletion routine evades critical mesh distortions. Infinite elements at the model boundaries avoid unrealistic deformation wave reflection.INTRODUCTIONExcavation in mining and tunneling is a costly and complex process. Special equipment such as the roadheader (Figure 1) is employed to cut the rock in the excavation process but high material strengths limit their usability (Tockner 1999). Nowadays a challenge is to extend their field of application to harder and more abrasive rock materials. The forces on the pick (Figure 2) are of great importance and determine wear and especially the efficiency of the machine. Figure 2 shows the principle of cutting and the predominant forces. The variation of pick geometry, cutting depth or attack angle will result in an alteration of these forces and determine the efficiency of the process (Tockner 1999). The mechanisms of rock cutting follow the principle of indentation (Kou et al. 1999). Directly under the indenter a hydrostatic stress state evolves causing the material to fail only due to crushing and fragmentation mechanisms. In the close surroundings large strains emerge and tensile cracks are formed but in a further distance the material behaves elastically."

Jan 1, 2015

By M. Yekich, W. R. Reed, G. Ross, M. Shahan

"Canopy air curtains on roof bolting machines have been proven to protect miners from respirable dust, preventing their overexposure to dust. Another desired application for canopy air curtains is in the compartments of shuttle cars. The challenges faced in developing the design of canopy air curtains for shuttle cars include mine ventilation rates in tandem with the shuttle car tram speeds. The resulting cab airspeeds may exceed 182 m/min (600 fpm), as found in the present study conducted in a central Appalachian underground coal mine by U.S. National Institute for Occupational Safety and Health (NIOSH) researchers. Prior research and laboratory testing had indicated that successfully protecting a miner in high air velocities is difficult, because the clean air from the canopy air curtain is unable to penetrate through the high-velocity mine air. In this study, the dust concentrations to which a shuttle car operator was exposed were measured, and air velocities experienced by the operator were measured as well using a recording vane anemometer. The results indicate that the highest exposure to respirable dust, 2.22 mg/m3, occurred when the shuttle car was loading at the continuous miner, where the average airspeed was 48 m/min (157 fpm). While tramming, the operator was exposed to 0.77 mg/m3 of respirable dust with an average airspeed of 62 m/min (203 fpm). This study indicates that a canopy air curtain system can be designed to greatly reduce an operator’s exposure to respirable dust by providing clean air to the operator, as the majority of the operator’s dust exposure occurs in air velocities slower than 61 m/min (200 fpm). IntroductionThe U.S. National Institute for Occupational Safety and Health (NIOSH) issued contract #200-2015-63485 to develop a canopy air curtain for coal mine shuttle cars with Marshall University and J.H. Fletcher & Co. (Salem, Begley and Ross, 2016). The proposed design maintains a design similar to that of a roof bolter canopy air curtain by providing filtered air through a blower over the operator. The plenum, which will provide uniform airflow over the operator, is anticipated to be built into the shuttle car canopy. One of the main interferences with a canopy air curtain is ventilation airflow perpendicular to the plenum airflow (Engel, Johnson and Raether, 1987). This ventilation airflow can shear the downward flow from the plenum, and this shear can reduce the effectiveness of the canopy air curtain by either disrupting the downward flow or allowing contaminated mine air into the canopy air curtain zone of protection."

Jan 11, 2018

By T J. Sprott, Associates

A number of people have expressed concern, understandably, that if mining operations take place in the Coromandel, the flows of mineralised ground water which exist will be intercepted. This water in many cases contains toxic metals including mercury, arsenic and lead and it is thought that if this water is allowed to enter streams or the waters of the Hauraki Gulf, it could endanger natural marine life and possibly established fisheries. This paper seeks to explain in simple terms the geology and the process of deposition of the various mineral deposits in the ground, the chemistry of the reactions between these minerals and the rain water falling on the ground, the hydrology and behaviour of this mineralised groundwater as it moves through the ground until it eventually enters the sea.

Jan 1, 1981

By AIME AIME

THE non-ferrous 'metals industry of the Soviet Union found itself in a very low position at the beginning of the reconstruction period in 1922, due to the absence of modern smelters and the run-down condition of the existing ones. Up to. 1924 there was no great demand for newly smelted non-ferrous metals due to the considerable stocks' of copper, zinc, lead, tin and aluminum in the courtry and also to the undeveloped condition of Soviet industries. However, in 1925 it became necessary to obtain new stocks of non-ferrous metals and in that year 12,000 tons of zinc, 14,000 tons of lead and 2,000 tons of tin and aluminum were imported into the U. S. S. R.

Jan 1, 1929

By S. H. Ash

For several years considerable activity has been devoted to economic and social factors affecting California metal-mining operations as they relate to accidents and their cost. The reason for this intense interest is that accidents cost this industry annually over $1100,000 in industrial insurance premiums for mines insured by insurance carriers only; during 1924-32, inclusive, they amounted to $3,616,9115. There are several reasons for this high cost, the most important of w rich are the consistently .high frequency and severity rates of injuries occurring in the industry. Coordination of effort, appreciation of a mutual problem, and widespread education are essential if accidents and their cost are to be reduced.

Jan 1, 1935