Search Documents

By Andrew Peterson

The Maine Department of Transportation offered this challenging design-build project for a new, 12-span, bridge over the Kennebec River in Bath, Maine. This structure would be built to replace the existing Carlton Bridge connecting the village of Bath, Maine to neighboring Woolwich, Maine. The design build team of Flatiron Structures, Inc., and Figg Engineers, Inc., elected to design and build a segmental concrete bridge. Site conditions dictated that this bridge would be supported primarily on deep foundations. Case Foundation Company joined the project team in the winter of 1997 to install twenty-two, eight foot diameter drilled shafts. The drilled shafts were designed with 8' diameter, permanently cased shaft sections and 7.5' diameter rock sockets. Shaft lengths ranged from 20' long near the river's edge to 100' deep in the middle of the river. Rock socket lengths ranged from 12' to 30' deep. Two Osterberg Cell load tests were conducted on production drilled shafts. Figg Engineers utilized the results of the load tests to "fine-tune" the rock socket design during construction of the drilled shafts. Construction of the drilled shafts proved to be very challenging and called on every member of the design-build team to work together throughout the project. One of the most challenging aspects of this project was in the installation of the 8' diameter permanent casing and drilling of the rock sockets. Early in the project, it became apparent that the top of bedrock was broken and unstable. This condition limited the advancement of the permanent casing and the affect of a "seal" at the top of rock socket. As a result, as the rock socket was advanced, loose material spilled into the hole and stopped progress of the socket. In order to resolve this problem, the design-build team developed a redesigned drilled shaft which included the installation of a steel sleeve to seal off the unstable rock formation. Following installation of the sleeve, the rock socket diameter was reduced to 7' diameter and advanced additional length to achieve required design capacity. All drilled shafts were installed with equipment supported on floating barges. Water access, along with the long shaft lengths and very hard bedrock required the use of cranes and drilling equipment that far exceeded the requirements of typical drilled shaft projects. This paper will discuss the relationship between design, construction, and equipment utilization on this challenging design-build project. [ ]

Jan 1, 1999

By R. D. Leitch, W. P. Yant, A. C. Fieldner, R. R. Sayers, S. J. Pearce

"The detection of leakage is a recognized problem in the safe and economic distribution and use of natural gas. Natural gas is practically odorless and therefore lacks he property of indicating significant leakage by the sense of smell, the means most widely used by gas employees and consumers for detecting leaks of the more odorous types of fuel eases. In view of the recognized value of the odor of gas for indicating leakage at the time of occurrence the Bureau of Mines has studied' the possibility of adding small amounts highly odorous substances to types of fuel gas (such as blue water gas and natural gas) that lack warning properties. These studies revealed that the mercaptans were promising substances to accomplish this purpose, not only for odorizing fuel gases but for other purposes° where it was desired to give warning through the sense of smell.Since completing the studies mentioned, the Bureau of Mines jointly with the American Gas Association has conducted further investigations dealing with the use of warning agents for fuel gases. The results of this work will be published later.The Bureau of Mines had been desirous of observing the practical use of ethyl mercaptan for detecting leakage of natural gas, particularly to determine whether the odor would permeate the ground and give indication of lea's in underground pipes. Opportunity for making these observations was recently given by E. A. Munyan, manager, gas department, Union Gas t Electric Co., who requested the bureau's cooperation in making leakage surveys of the company's distributing systems at Franklin and Middletown, Ohio."

Jun 1, 1930

By Bas R. Hemmen

GeoBrain is a facility at GeoDelft with the purpose to provide society with all relevant geo-engineering knowledge and experience in a structured way. On the basis of the available knowledge and experience engineers, decision makers and construction supervisors can come to a fast, reproducible and objective choice, taking into account the consequences. The paper presents examples from the GeoBrain experience databases and forecasting models developed for foundation engineering and directional drilling, or: "GeoBrain Foundations" and "GeoBrain Drilling". GeoBrain is closing the gap between theory and practice. It is aimed directly at reducing uncertainty and the costs of failure, thereby increasing the quality of profession and minimising the risk in geo-engineering works.

Jan 1, 2006

By C. van Tonder

Paper written on project work carried out in partial fulfilment of B Tech (Engineering Metallurgy) degree This investigation relates to a multi-purpose electrolytic system. Its primary purpose is to electrowin gold from high or low concentration gold cyanide solutions and/or from gold sludge, and to convert the recovered gold into a gold (alloy) electroform or electrode at the gold mine itself. These operations are carried out sequentially and in situ in the same electrolytic cell. Electrorefining of the gold recovered may also be done in the cell. The system applies to silver as well, and may be adaptable to base and platinum group metals. It could also be used in environmental applications, to remove undesirable metals present in aqueous solution at very low concentration. The work to be discussed forms part of recently filed patent applications. Subsequent and future developments of the system are briefly outlined. This paper, in part or in full, has been published by the Metallurgical Mine Managers Association (MMMA), with permission from the authors.

Jan 1, 2006

By Robert L. Mentch

CADMIUM is one of the metals apparently destined to remain relatively scarce. The en tire supply of primary cadmium is recovered as a byproduct, concurrently with the treatment of ores of other metals. Development of the cadmium industry is attributed to metallurgical improvements in the zinc industry; output depends almost wholly upon zinc production. Cadmium is a metal of specialized uses where its superior performance has developed a strong, expanding demand. The supply, however, has been relatively unresponsive to price because of its byproduct nature. Cadmium's outstanding properties would assure it a manyfold greater market if more were available at lower prices.

Jan 1, 1958

By Bengt H. Fetlenius

The "Pile Prediction Event" at the ASCE GeoInstitute's Deep Foundation Conference in February 2002 involved prediction of drivability and capacity of three 14m long, 324mm diameter, closed-toe pipe piles driven into loose to compact fine sand to slightly silty sand. Predictors were provided the results of two soil borings and three cone penetrometer tests, as well as type and model of hammer to be used for the pile driving. A total of 33 persons submitted predictions. As to penetration resistance distribution, many predictions were far below actually observed values. As to capacity in compression, the predicted values ranged from 270KN through 2,340KN with a mean of 1,070KN. As to capacity in tension, the predicted values ranged from 100KN through 1,650KN. The maximum load applied to the compression pile in the static loading test was 1,25OKN, at which no more reaction load was available. The reaction system for the tension test failed early in the test. CAPWAP analysis on End-of-Driving blows showed capacities at the end of the driving for the push and pull piles of 670KN, and 710KN, respectively. No restrike tests were made. Additional CPT soundings indicate that the pile driving had densified the soil. Static analysis and calculations from the CPT indicated that capacities ranged from 1,000KN through 2,000KN. The paper presents the data and discusses the various methods of determining pile capacity and addresses influence of set-up Lessons useful for future similar events are indicated.

Jan 1, 2004

By S. Marx

More than twenty years ago Sasol, ISCOR, and some parastatals played a major role in ensuring that South Africa had sufficient technical skills. When the economy became tight and business and government were pressurized to decrease costs, the first budgets that were reduced were the training budgets. It seemed to be too expensive and too time-consuming to train apprentices. According to Stacey2, this is a major strategic issue facing the mining industry in South Africa. Two factors added to the shortage of skills challenge: ? Skills erosion and job losses ? Artisans ? currently the economy produces 5 000 but the need is 12 500 ? Level of mechanization in South Africa less than 10 per cent ? Average age of operators and artisans is 50 ? Greater awareness of occupational health effects of hand-held drilling. ? Workplace challenges ? The impact of HIV/AIDS and other employee wellness issues ? Changes and challenges in workplace environment i.e. the mining industry.

Jan 1, 2012

Mr. Chairman, distinguished guests, ladies and gentlemen. Thank you for asking me to your conference, with its most fundamental and appropriate topic of 'Investment in Mining'. I must confess at the outset that I am one of those Australians who has rarely visited your fair land of New Zealand. This is in fact only my third visit, with all three related to Institute Conferences, and all much too brief. In so many ways your country provides a counterpoise to ours, despite the obvious disparities in size and population. And I am not only referring to the Bledisloe Cup! We would certainly each be much more lonely without the other, in this strange long-lost corner of the globe û if globes can have corners. Such an important factor in common in our shared heritages has been the mineral industry we have won from our alluvials and our rocks û especially for gold. So much of the major mineral developments which have supplied the world's appetite for metals and fuels in the past two hundred years has come from the countries settled in that period by people from Europe, especially those from the British Isles. So much of the technology for mineral and metal extraction has come from the skills of those people in New Zealand and Australia. And so much of the further development of metal processing and manufacturing of productive equipment has come from those people and from their cousins throughout the world. It is, I believe, a fair question to ask why we have failed to build on those early and considerable successes, and why we have in so many ways apparently been so content to allow others to add value to our raw materials, and to take our technological developments on to levels far beyond those that our domestic markets could sustain.

Jan 1, 1988

By Harold V. Pearce

(Chattanooga Meeting, October, 1908.) THE fire which occurred in the fall of 1906, at the works of the Boston & Colorado Smelting Co., Argo, Colo., destroyed entirely the gold- and silver-refinery of the plant; and in view of the development of modern practice in the refining of copper-mattes, etc., the management decided that it would be inadvisable to rebuild that part of the works for the continued use of the process which had been conducted therein for so many years as a metallurgical secret. This decision probably removes altogether from the sphere of practice the " Pearce " method for the separation of gold. At all events, it removes the business reasons which have prevented hitherto the publication of the principles involved. At the suggestion of Dr. Raymond, Secretary of the Institute, my father, Richard Pearce, the former manager of these works, has requested me to prepare a brief description of this process for the benefit of our members. Since I severed my connection with the Boston & Colorado Smelting Co. some time ago, I am indebted for some practical details to the present superintendent, Charles Rees, whose friendly assistance I would gratefully acknowledge. With regard to the history of the inception and development of this process by its inventor, Richard Pearce, I cannot do better than quote freely from his own notes and papers. HISTORY OF THE PEARCE PROCESS.' "In 1874 my entire time was directed to the improvements and additions to the plant at Black Hawk. The changes which I had made in the construction of the furnaces at Black Hawk proved so beneficial that I was requested to introduce the improvements at the branch works at Alma. These changes were carried out as speedily as possible, and proved of great advantage as compared with the old system. "The separation and refining of the gold from the matte now engaged my attention, and since previous experience in the treatment of gold-bearing matte and

Feb 1, 1909

By Akira Kaneda

Mitsubishi continuous process employs an electric furnace for settling matte from slag. Electrodes are immersed into the slag layer in the slag-cleaning furnace and the temperature of the melt is maintained at a predetermined level by Joule's heat. Electrodes are immersed to the depth where the current of each electrode is kept at a set value, and they are raised or lowered automatically to compensate for the deviation from it. Because electric resistance of the bath is varied with the matte level in the furnace and the composition and temperature of the slag, the immersion depth of the electrodes is affected by them. Therefore by monitoring the immersion depth and its change with time, abnormal situations in the furnace, such a~ rise of matte level or local abnormal state of melt, can be detected. In this paper, relations between state of the furnace and electrode behavior are discussed based on the plant data, and then a new and simple monitoring method of the condition of the furnace is proposed.

Jan 1, 2001

By E. R. Packer

"The mill of Anaconda Britannia Mines is located on the eastern shore of Howe Sound, approximately 32 miles north of Vancouver, British Columbia. The mill has a daily capacity of 3400 to 3500 tons and at the present is treating chalcopyrite-pyrite ore from which only the copper mineral is concentrated. For a clear conception of concentrate filtering and shipping practice at Britannia perhaps a bit of past history should be related.For many years the mill concentrated copper and zinc minerals and intermittently a pyrite concentrate was produced. It was general practice to ship copper concentrate by towed barge down Howe Sound, across Juan de Fuca Strait and thence down Puget Sound to Asarco's smelter at Tacoma, Washington. Zinc concentrate was loaded in hopper bottom rail gondolas spotted on rail barges and towed to rail heads in Vancouver, thence by rail to Anaconda Reduction Works in Great Falls, Montana. Most of the pyrite produced was shipped by ocean freighters to Japan and Taiwan with an occasional barge load of 2000 to 4000 tons to nearby customers in Vancouver and the state of Washington.In recent years, because of smelter shut-downs for one reason or another, mostly strikes, a considerable amount of copper concentrates has been shipped by ocean freight to Japan and in 1971 several lots were loaded in gondola cars and shipped by rail to the Anaconda smelter in Anaconda, Montana, because Asarco's smelter was forced by municipal and state anti-pollution laws to limit the amount of S02 emission from the smelter stacks. Zinc concentrate production was halted in the early part of 1Y70 because of zinc depletion in the ores and pyrite production was stopped in May, 1971, because of a lack of markets.Filter equipment in the Britannia mill consists of conventional disc vacuum filters and reciprocating vacuum pumps. The copper concentrate filter was installed in 1923 as a 6 x 8'6"" American disc type manufactured by United Filter Corporation, The zinc concentrate filter, now converted as a spare for copper concentrates, is also a 6 x 8'611 American disc manufactured by Traylor Engineering and Manufacturing Company and was installed the same year. Formerly, there were, in addition, two 4 x 6' disc filters for pyrite and two 6 x 6' disc filters to de-water bulk flotation concentrates ahead of the regrind mills. Installed vacuum pumps were two Ingersoll Rand 22"" x 811 and one 22"" x 9"". One of the smaller machines has since been scrapped.At the time of the writer's transfer to Britannia in 1965, the entire filter system was operating as a unit using two vacuum pumps and a common filtrate tank with a 2"" SRL filtrate pump for five operating filters. The regrind and pyrite filters were in continuous operation and the co11p('r concentrate filter alternated with the zinc concentrate filter because both copper and zinc concentrates were transp0rted to storage by the same conveyor belt."

Jan 1, 1972

By Cz. Mora, A. Pawelczyk, D. Hreniak, P. Nowak, A. Dyonizy, S. Strek, W. Strek, K. Grabas, A. Ostrowski

Globalization and a growing demand for limited raw material resources have forced changes in the approach to the supply chain. This is particularly true in the case of rare earths, which are regarded as one of the most important development indicators of modern technologies. To ensure a secure supply of commodities, the European economies have been prompted to investigate REE recovery from sources which until recently, for technical or economic reasons, were considered not sufficiently attractive. An interesting example is apatite phosphogypsum waste dumps. The REE content in these waste dumps averages around 0.5-1 %. One of the most important phosphogypsum locations in Poland is the Lower Silesia region where a phosphoric acid Chemical Plant "Wizów" operated for several dozen years. In this work, rare earths are leached from the phosphogypsum crystalline structure by a chemical treatment and can then be separated into individual chemical compounds. The technology used in these recovery tests, matches up to a coherent European raw materials policy supporting effective management of resources and promoting waste materials recycling.

Jan 1, 2014

By D. S. Saxena, Jack K. Tuttle

Lack of understanding of useful applications of explosives on construction work stem primarily from the fact that explosion is commonly associated with destruction. On rock excavation and other construction works a certain quantity of explosive is harnessed to perform useful work at the source e.g. blasts to disintegrate rock. Development in rock blasting techniques, including the use of multiple-row blasting with short delay ignition, have made it impossible to excavate rocks close to or below buildings even in closely built-up areas. To permit the use of explosives on construction projects, in ways that will not damage existing structures, guidelines have been developed from careful measurements of intensity of ground vibrations. Accurate electronic instruments are now available for doing this. PLANNING AND CONTROL Blasting operations must be carefully planned and carried out to avoid discomfort to persons or damage to property. This increase in the use of rock blasting in city areas alone has led to a number of problems due to ground vibrations, air shock waves, and the psychological effect of noise. While the latter seldom if ever causes damage, it does create irritation and discomfort to persons living or working near the blasting sites. A result of this is a steady increase in the number of complaints in respect of damage to houses and other premises. Many such complaints are genuine and damage may undoubtedly be caused when incorrect blasting techniques are used.

Jan 1, 1997

By R. W. Dougherty

From time to time interest has been evidenced in transporting coal with water in pipe lines. About the year 1895, United States patents broadly covering a method of pumping coal with water through pipelines were granted to W. C. Andrews. His process was used to some extent in pumping anthracite culm and waste back into the worked-out portions of the mines. About 1905, W. T. Donnely was granted patents relating to pumping anthracite silt away from the breakers. From about 1913 until 1924, a British engineer, Gilbert G. Bell, used a short pipeline to convey coal with water from barges on the Thames River to the Hammersmith Electricity Generating Station, London. Minus 5-inch coal was transferred 660 yards through an 8-inch pipe. Some trouble was experienced with fine coal, which tended to plug the line. Bell made several proposals to transport coal by pipeline overland from the Midlands to London, a distance of about 100 miles, but these were never adopted. This survey is concerned mainly with the problems presented by actual pipeline transportation of coal with water. It is assumed that the coal will have been processed to remove most of the abrasive impurities by conventional methods prior to introduction into the line, and that it has been crushed to the required top size. Dewatering at the discharge end of the line is considered part of the conventional cleaning process. There still remain many pump-performance and behavior of water-coal mixture problems that can be solved only by actual performance tests. It is recognized that the distribution of coal to other than very large users is not changed. Large storage areas would be required to supply seasonal markets. Large users, such as power plants and heavy industries, could be supplied by branch lines directly to the point of use, It is also recognized that pipe lines might not be able to carry a full range of sized coal to meet market demands in many areas.

Jan 1, 1951

THE SECRETARY The year 1917 has been a notable one in Institute affairs. The usual activities, including meetings, publications, local section interests, library service, and so-forth, have been continued on at least the same scale as previously, and in addition the resources of the Institute have been placed without stint at the service of the Nation, not only for the active prosecution of the military side of the war, but even more especially in the industrial operations which form the very basis of modern warfare. The officers and directors of the Institute have labored both officially and individually, while the Institute as a body, through committees of, prominent members, and through many individual members, has given freely. Finally, Institute funds have been appropriated to an amount exceeding $5000 to accomplish the cooperation with Government bureaus, and provide committee expenses necessary for performing the services that have been given. The President of the Institute had a very large personal share in many of these activities, which will be described in the following pages, as well as in the President's own report. Many of the Institute's members are giving their whole time for. $1 a year, or less, and especial mention should be made of Herbert C. Hoover, Food Administrator, W. L. Honnold, Head of the Commission for Relief in Belgium, Mark L. Requa, Petroleum Administrator, Edgar Rickard and Charles W. Merrill of the Food Administration, S. A. Taylor of the Fuel Administration, W. L. Saunders, B. B. Thayer and Joseph W. Richards who .are giving a. large share of their time to the Naval Consulting Board, W. Y. Westervelt, W.0. Hotchkiss and Harvey S. Mud of the War Minerals Committee, David W. Brunton of the War Committee of Technical Societies, and hundreds of others whose names are mentioned in the Honor Roll of Members. It has also been a notable year in cooperation with sister-societies. The most important event under this head was the accession of the American Society of Civil Engineers into the fraternity of Founder Societies.

Jan 2, 1918

By M. M. Oosterveld

"In South West Africa diamonds are mined from ancient beach deposits by the Consolidated Diamond Mines of South West Africa, Limited.To improve the control of mining production, a computer is used for the calculation of statistically more accurate and homogeneous ore blocks. Geological and sampling information has been digitized and stored on magnetic files.The figures derived for each block entail the calculation of the diamond size frequency distribution, the diamond density distribution and the ore reserve by using the density distribution.The diamond size frequency distribution is used for estimating the revenue in an ore block.A description is given of how a linear programming system can be used for production planning."

Jan 1, 2014

By Chas. F. Jackson

This paper is one of a series dealing with mining methods and costs, prepared and published under the sponsorship of the United States Bureau of Mines and made possible through the cooperation f many mining companies in the United States and foreign countries. The preparation of this paper follows a field study of top-slice mining during which the author visited and discussed with operating officials a large number of iron mines in the Lake Superior region. During this study special note was made of changes in top-slicing practice during the past decade, prior to which the author had acquired several years experience with the method through active connection with a number of mines employing top slicing.

Jan 1, 1931

By Ralph Harris, Xia Qi, Frank Komsic

"Gold cyanidation kinetics which are often limited in commercial operations by the rate of oxygen dissolution from gas bubbles into the slurry, are discussed. Emerging technologies for improving the rate of oxygen dissolution are compared and the gas efficiency, energy use and operating performance of inverted cones and a device based on a jet diffuser are examined. The effect of solids loading is also reviewed and a relationship between operating parameters and the kilograms oxygen dissolved per kilowatt-hour is presented.Inverted cones are shown to create slurry settling problems at high gas flow rates and surface tension lowering agents are shown not to greatly improve the overall rates of oxygen dissolution.The novel jet diffuser technology operates at a range of gas to liquid ratios that improves its energy use over conventional technology and the performance of a number of designs are discussed.Gas efficiencies as high as 35% were observed with the novel diffusers at 40 cm diffuser immersion and are expected to increase at greater immersions. Energy use of 1.8 kg 02 I kWh were estimated for prototype full size diffusers operating at 100 cm immersion. Energy use of 3.S kg 02 /kWh is conservatively expected at 600 cm immersion.IntroductionGold ExtractionGold that can not be recovered by gravity separation can be recovered by either the Merrill-Crow process or the newer carbon in pulp (CIP) or carbon in leach (CIL) processes 1. Reductions in operating costs and improvements in gold recovery are central mill operating strategies. The present paper examines the potential for improvement that can be achieved in the gold cyanidation step of gold recovery. This paper introduces a number of emerging technologies and provides a basis for comparison of the performance. It shows that the basis for comparison of a particular technology depends on the type of gold extraction circuit employed and the type of reactants employed."

Jan 1, 1996

By S. W. Zoldok

"ERRATUMFor paragraph 1, page 1, read the following:The Cle Elum nickeliferous iron deposits occur on an unconformable contact between the serpentine and overlying Swauk sandstone formation and extend about 2 miles along the Cle Elum River in Kittitas County, Wash.The linear extent of the deposits and their proximity to a large source of,electric power and coal supply indicated that a development program was in order to determine the probable grade, extent of the ore bodies, and a suitable metallurgical process for recovering the iron, nickel, and chromium from the ore.The northern portion of the serpentine formation was investigated by the Bureau of Mines from August to December 1943 and from August to October 1944. The investigation consisted of road building, diamond drilling, sampling, and metallurgical tests.The Geological Survey assisted with logging of cores and made geologic and topographic maps."

Feb 1, 1948

By J. A. Pontius

The Cresson Deposit is located in central Colorado within the historic Cripple Creek Mining District. The deposit has moved from its initial discovery in 1990 to full production in less than five years (current reserve nearly two million ounces). This accomplishment required a great deal of cooperative teamwork between the exploration, development, permitting and corporate groups. Nowhere was this cooperation more evident than in the construction of the geologic block model. The detailed modeling of gold and its metallurgical characteristics formed the foundation upon which critical financial and design decisions were based.

Jan 1, 1995