Search Documents

By A. M. Croll

The efforts to mechanize narrow reef tabular orebodies unique to this country, are not new. They began in the early 1900s and have over the last century seen varied rates of progress and success. Efforts to mechanize with the use of scraper winches can be regarded as a success. The scraper winch replaced the hand lashing of ore and development waste into hoppers. The initiatives by Anglo Gold and the then JCI to implement trackless mining equipment into these environments had limited success but in general were looked upon as a failure?at least this is the perception. The Chamber of Mines Research Organization (COMRO) in conjunction with various mining houses tried to make a success of the impact ripper. Diamond wire cutting of the stope face is another, which has been tried and tested. The use of high-pressure water to cut rock has also been trialed. These attempts, amongst others, are just a few of the efforts that have not been successful in the quest to make life at the face safer, more productive and easier for our employees. Against the backdrop of an emerging South Africa, the associated high expectations of historically disadvantaged people within the country, a strong rand, demands for better safety, lower cost of production and more efficient operations, mechanization has the chance to make a difference to Anglo Platinum?s business. Mechanization has certainly changed the way other commodities such as coal, base metals and diamonds are won from the earth. Mining?s image is still one of people crawling around in stopes?a dirty, ?low-tech? business. Anglo Platinum?s latest journey to mechanize its underground operations began in earnest in1998 and has enjoyed some successes and failures. The opportunity to change the way mining is done within the company is there. Technologies are evolving, and the implementation of mechanization can certainly assist with the achievement of the goals referred to above. When mechanization commenced, targets were set for the company to achieve but these have been revised in the light of recent events relating to the strengthening rand and a slow-down in expansion plans. However, the intent to mechanize appropriately in Anglo Platinum still exists.

Jan 1, 2004

By G M. Mudd

Mine tailings represent one of the two largest sources of mine waste from the minerals industries (the other being waste rock). Given the problems of declining ore grades and growing production, tailings generation is increasing exponentially across the global mining industry. Common practice is for mines to build large containment dams to store tailings during operations, which are then rehabilitated following mine closure. At some sites, however, the controversial practices of riverine or marine dumping of tailings is still practiced. As recent tailings dam failures have shown, there are legitimate questions being raised about the long-term viability of leaving tailings above ground due to the risks of collapse and failure. At present, it is rare for mines to emplace tailings back into former mine voids following mine closure, most commonly into a former open pit mine void (although a fraction of the tailings may be used for underground mine backfill, this is minor in scale). The approach of in-pit tailings has numerous advantages, such as inherent physical stability, low to negligible acid and metalliferous drainage (AMD) risks, as well as allowing more productive use of formerly mined land. In tropical areas where surface repositories are prone to leakage with potential for AMD and widespread dispersal of radionuclides (in the case of uranium mining), in-pit management provides particularly strong advantages – thorough hydrogeological studies are required, however, to address residual groundwater contamination risks and to establish sound, long-term environmental monitoring regimes for groundwater quality and subsidence issues. This paper presents a study of in-pit tailings management and compares it with surface repositories established in a tropical climate. The comparisons lead to the conclusion that, at least under tropical conditions, in-pit tailings management should be considered as world’s best practice – especially for radioactive uranium tailings.

Aug 8, 2011

The coalmining industry in most countries has, at various times, suddenly been confronted with a decrease in demand for coal. Readjustments made to reduce productive capacity to match the reduced demand for coal have often resulted in hardship to mineworkers, loss of capital investment to mineowners and loss of coal reserves. The consequences of the methods of readjustment adopted in the past have contributed to the low esteem in which coalmining has come to be regarded by a large section of the gel).eral public in many countries.Four sections of the coalmining industry, representing different periods of time, different countries, and different methods of industrial organisation have been examined:Great Britain and the U.S.A. during the inter war years, the post war European Coal and Steel Community, and post war Great Britain under the National Coal Board. An assessment has been made of the methods adopted in each case to reduce productive capacity to match a reduced demand for coal. Finally the fundamentals of the problem-as it affects the coalmining industry of any country-are considered, and possible solutions put forward.During the 1950's, surplus productive capacity was a problem in many coalmining countries, including Australia and New Zealand. As a rule no techniques are developed beforehand to solve problems introduced by a sudden decrease in demand for coal. The situation is usually tackled by a series of short term decisions based on expediency, which often in the long run only aggravate the problem.

Jan 1, 1961

By Md. Amanullah

A novel triple action load cell assembly (LCA) was developed to determine three index parameters reflecting compressive, tensile and shear characteristics of mudcakes. The results indicate that the tensile, compressive and torsional behaviour of mudcakes are strongly influenced by the physics and chemistry of the mud additives. Eine neuartige dreifach wirkende Druckkammer zur Bestimmung der drei Indexparameter Druck, Zug, und Scherung von Spülungskuchen wurde entwickelt. Die Ergebnisse weisen auf einen starken Einfluss der physikalischen und chemischen Spülungszusätze auf Druck, Zug, Scherung hin. Un assemblage d'une nouvelle cellule a triple action (LCA) a été développée pour déterminer trois paramètres caractérisant la compression, la contrainte en traction et la résistance á la fracture des cakes. Les résultats indiquent que les comportements tensile, compressif et de torsion des argiles sont fortement influencés par la chimie et la physique des additifs des boues.

Jan 1, 2003

By Ioannis Paspaliaris, Dimitrios I. Gerogiorgis, Dimitrios Panias

"Red mud fiberization is a process with remarkable potential, alleviating environmental pressure by transforming an aluminum by-product into mineral wool, thus to various marketable products. A promising mineral wool process is molten slag fiberization via an impinging air jet, which avoids mechanical wear and rotating parts. The molten slag which remains after pig iron casting flows out of a heated ladle orifice at a high temperature (1600 °C) and adjustable flowrate, and forms a free-falling vertical jet which visibly radiates its excessive heat: at a given distance, a high-velocity impinging air jet meets the vertical melt jet perpendicularly (or at an angle), inducing intensive droplet generation, subsequent fiber elongation, collection and processing.This paper focuses on high-fidelity CFD modeling of the molten jet flow under external cooling: the model encompasses all physicochemical phenomena (melt laminar flow, radiative cooling) and considers several temperature-dependent slag transport properties in order to understand which operational degrees of freedom (manipulated variables) are useful to process optimization."

Jan 1, 2012

By Edwin R. Phelps, Charles W. Porterfield

BACKGROUND OF SURFACE MINING Surface mining refers to the process of removing the material (over- burden) overlying a coal seam and exposing the coal so that it can be loaded out and conveyed by trucks or other methods to the preparation plant or other facility. Surface mining has not always been important in the coal industry. In the early 1900s, almost all of the coal mined in the United States was mined by underground methods. In 1900, about 192 Mt (212 million st) of bituminous coal mere mined and less than 1% was mined by surface methods. The development and use of larger equipment has allowed surface mining to gain prominence throughout the years. Table 1 shows the total production of coal by mining method in the United States for ten-pear periods since 1920 and indicates the growth of surface-mined coal production. Surface mining will undoubtedly continue to account for a large percentage of the coal production in the US for many years because: 1) The capacity of surface mining excavators has continued to increase. Today, mining companies are using shovels (see Fig. 1) which are able to move up to 137.6 m3 (180 cu pd) in each bite and draglines (see Fig. 2) which move up to 168.2 m3 (220 cu pd) in each bucketful. 2) Increasing tonnage from the thick western coal seams is being produced by surface mining methods. 3) Surface mining has normally had lower costs and a better safety record than underground mining. 4) Surface mining normally recovers a much higher percentage of the coal reserve than can recovered by underground mining. 5) Some coal measures call best be extracted by surface mining

Jan 1, 1981

By J. L. Jernegan

In this paper I propose to give a short and, I must confess, a rather incomplete description, as regards many details, of the process used in Chicago, Ill., for smelting the argentiferous ores of the far West, and shall confine myself in this description, principally, to the process used at the Chicago Silver Smelting and Refining Company's Works, known as the Balbach process, as all the other smelting works in that city follow the same method, with the exception of one, which has the Cordurié process for the desilverization of argentiferous lead. In all, there are five silver smelting and refining works in and near the city of Chicago. The Chicago Silver Smelting and Refining Company's Works are situated at the little station of South Lynne, about seven miles south from Chicago. The plant at these works consists of one horizontal steam-engine, principally used for running the ore pulverizer, four reverberatory smelting-furnaces, connected by horizontal flues with a common chimney 85 feet high, three lead-softening furnaces, one so-called zinc or mixing furnace, one separating furnace or liquation hearth, one lead-refining furnace, three zinc distillation retorts, one English cupellation furnace, supplied with blast by a No. 3 Sturtevant blower, which is run by a small steam-engine having a vertical tubular boiler, and an assay office, in which there are two windfurnaces of the ordinary construction, and also a small muffle furnace. The assay office is supplied with all the necessary apparatus and reagents for fire assaying. There are also a superintendent's office, various store-rooms for coke and charcoal, and for the preparation of fire-clay, etc. Recently a small slag hearth (Krummofen) with one tuyere, has been put up for the purpose of working over such slags as assay too high in silver and lead to be thrown away, of which there are large amounts. The principal ore worked while I was in the employ of the company was that of the well known Emma mine in Utah, and also small quantities of Colorado ore. The character of the Emma ore is well known to most members of the Institute. In consists principally of ferruginous mixtures of carbonate and oxide of lead, oxide

By T. O. Breitling

Two significant problems In mill design are environmental control and cost reduction. Environmental control is predicted to be 5-10% of total plant costs in some parts of the U.S. Operating and design companies will assign this new "unit operation" a place in the early flow sheets. More advanced environmental control will add to both capital and operating costs, so mill designers will strive to reduce other costs.

Jan 1, 1970

By Warden A. Moller

(Pittsburg Meeting, March, 1910.) THE Fushun coal-field, now being opened up by the South Manchurian Railway Co., is connected with the main line by a branch, 30 miles long, from Sui Chia Tun, 10 miles south of Mukden, the capital of Manchuria. The coal-field, which lies on the southern bank of the Hun river, 25 miles east of Mukden, consists of a long narrow valley,. running east and west between hills composed of granitic and volcanic rocks. At the foot of the northern hills, the Hun river flows westward towards the Liao river, which drains the greater part of South Manchuria. At the foot of the southern hills, resting immediately upon volcanic rocks, and overlain by 20 ft. of alluvial, is a thick layer of Tertiary shales, carrying near the base two coal-seams. In many places the lower of these two seams is in immediate contact with volcanic lauds and basalts, the flows of which were evidently both prior and subsequent to the formation of the coal-seams. This contact has practically destroyed the lower seam for commercial purposes. The value of the field lies in the upper seam, which, for a length of nearly 8 miles, varies from 100 to 130 ft. thick. Of this seam, 85 per cent is good coal. The seam dips to the north conformably with the shales, at angles of from 25° to 30°, and appears to have an uninterrupted dip for about 1.5 miles before being possibly cut o$' by the northern hills. The coal-bearing shales extend east and west for a length of about 20 miles, but towards the east the continuity of the seams is broken by intrusive rocks. The coal is of the sub-bituminous variety, low in ash, bright in appearance, and breaks with a conchoidal fracture. It has the usual qualities of Tertiary coal-quick steam-raising and poor stacking-qualities. Pieces of resin, varying in size from

Apr 1, 1910

By Michael Rieber

The increase in f.o.b. mine prices of coal from $5/ton to over $18/ton in five years [1] has increased the significance of transportation costs. Coals produced in the vicinity of the consumer bear a much lower transport cost than those produced in the west. This differential may be used for flue gas desulfurization, other cleaning, or further processing of local coals. To the extent that western coals are cheaper to produce and have a lower sulfur content, they offset the locational disadvantage. To the extent that they have a lower heating value, the disadvantage is exercabated. Given the other conditions, an accurate analysis of transport costs will help suggest the location of coal mining and the moue of transport both transport costs and tariffs have risen. Together they have increased delivered coal prices, altered the balance between the use of coal and other fuels, helped to alter the location of mining activity, and put pressure on consumers to examine the cost effectiveness of alternative transport modes. Transportation options for long distance coal movements include rail, barge, pipeline, and EHV transmission lines. A summary of system parameters is shown in Table 2.1. Barge transport, pneumatic and slurry pipelines are discussed elsewhere in this report. Together with EHV, they have been the subject of previous studies [2,3,4]. Slurry pipelines have been shown to be especially useful where rails are not available [2] but the technical problems of dewatering, handling, and utilization of lines [5] remain unresolved. They are discussed in Section 3. Barge transportation depends on the location of the mine and consumer with respect to the waterway system. One drawback of barge shipment is interruptions due to winter, and low or high water conditions. Mine mouth power generation followed by EHV transmission of over 500 miles has been shown to be the most expensive means of delivering an equivalent amount of energy to consumers [2].

Jan 1, 1977

By J. A. González-Anaya

This laboratory work presents a study of the effect of ultrafine grinding on the gold recovery of a highly refractory gold concentrate. The particle size of the concentrate was P80 = 46 µm and the main species present were quartz (28.58%), dolomite (25.63%), pyrite (20.93%), arsenopyrite (15.39%) and 112 g/t gold. After optimizing hydrated lime and lead nitrate additions, standard cyanidation with 1% NaCN, pH = 12.3, 25% S/L permits to recover only 9.4% of the gold. Different particle sizes were submitted to cyanidation. When the concentrate was ground to ultrafine sizes (P80= 4.6 µm), the gold recovery for the same cyanidation conditions increased to 67%, with cyanide consumption of 66.7 kg NaCN/t. Additional tests were performed in order to reduce the cyanide consumption. The reduction of the cyanide concentration in the leaching solution from 1 to 0.5% and the addition of 100 g Pb(NO3)2/t allowed the reduction of the cyanide consumption to 27.6 kg NaCN/t (58% reduction), while maintaining the same gold recovery of 67%. The remaining gold could be present as very fine inclusions or in solid solution in the matrix.

Jan 1, 2011

By P. R. Geoffoy, T. Koulomzine

"The discovery of the Mogador deposit concealed by 100 feet of overburden was the result of combined application of geological reasoning, ground geophysical surveys, studies of glacial float and extensive diamond drilling. The ground was acquired because it lay on the projected intersection of the Manville and Laflamme River faults. Systematic ground prospecting led to discovery of mineralized floats. A first unsuccessful exploration campaign lasted several years and consisted of 137 drill holes.In 1951 the boulder nests were reexamined and an associat'on of the mineralized float with boulders of a granodiorite, unknown in outcrops of the district, was established. Consequently, ground magnetic surveys were extended and re-interpreted, and a large anomaly interpreted as corresponding to a batholith was outlined. The existence of the batholith was immediately confirmed by drilling and the Mogador deposit discovered in third hole of new drilling programme in a zone of fractured volcanics paralleling southern contact of batholith.The Mogador deposit is a complex replacement of silicified volcanics by pyrite, pyrrhotite, sphalerite, chalcopyrite and galena carrying values in silver and gold. A total of 1,230,000 tons has been indicated, most of it now classified as fully developed proven ore."

Jan 1, 1960

By A. M. Strachan

The application of submerged electric arc furnace smelting techniques to tin concentrates at the Capper Pass tin smelter in England is discussed. Some experimental data from earlier small scale 50 KVA electric smelting testwork on various low and medium grade tin concentrates is presented. Design considerations for the construction of a 3 MVA electric furnace to treat tin concentrates from the East Kemptville mine in Canada are considered, together with necessary precautions peculiar to the construction of a high grade smelter in close proximity to an existing low grade, complex non-ferrous metal smelting operation<. Slag composition modifications to optimise operational smelting conditions for various concentrates treated are discussed, together with refractory selection. The effect of concentrate impurity levels on the permissible degree of recycle to produce a satisfactory metal product is highlighted.

Jan 1, 1990

By W D. Rech, K W. Keskimaki

As an integral part of the conversion from rail haulage to conveyor haulage at Henderson, over six kilometres of drifting and several large complex openings were mined. The deepest of these areas was nearly two kilometres beneath the surface, bringing all of the challenges of rock stress and heat that come with mining at these depths. Though many mines operate at these depths, the development of the infrastructure necessary to support a 36 000 tonne per day caving operation brought some unique challenges to the development mining activity. The issues handled include: finding experienced staff for a æfast trackÆ development program; rock bursts and ground conditions; inflow of 50 degree centigrade water; acceleration of the project completion; large diameter raise boring and difficult muck handling.

Jan 1, 2000

By Allan M. Johnson

Since 1974 researchers at Michigan Technological University have been studying mine subsidence in the Iron River District of Northern Michigan. The district, which was active from 1881-1978, has had numerous cases of subsidence. Much of the subsidence resulted from rock mass failure but some appeared to have developed primarily in the thick glacial overburden which is a typical feature of this area. This latter observation led to the recognition that some of the surface subsidence was due to piping; i .e., loss of overburden material to the mine voids by groundwater flow (Johnson and Frantti, 1978). The Sherwood Mine was the last mine to operate in the district. With its closedown scheduled for late summer of 1978, a unique opportunity to monitor the mine as it flooded was presented. It was reasoned that with the cessation of pumping, groundwater would rise in the overburden and the mine would flood. The physical characteristics of the mine were favorable for piping to occur as the mine flooded. With the permission of Inland Steel Mining Company and the support of the U. S. Bureau of Mines, a project to monitor the Sherwood Mine for piping subsidence began in June of 1978. This paper present aspects of this study pertinent to the piping-induced subsidence events which occurred at the Sherwood Mine in 1980 and 1981, including acoustic emission monitoring of the subsidence activity, hydrologic monitoring of the groundwater regime and the flooding mine, laboratory modeling of the piping mechanism, and analytic procedures which are under development.

Jan 1, 1982

By T N. Little

The aim of any rock breaking activity is to achieve success by developing designs that are blasting objective-specific and geology-specific, and then implementing such designs. This paper targets mining geologists with the aim of extending their knowledge of the rock fragmentation processes and providing insights to the significant relationships between geology and blasting. There are two main relationships, and if mining geologists appreciate both these relationships, then they can play a key role in optimising production. The business risk continuum is introduced to support this understanding. The first relationship is between geology and potential blasting hazards, and the operational complexity required to manage those risks. The risks associated with eight different ground types are discussed in terms of ground conditions, hazards and controls. These types are: reactive ground, hot ground, geothermal ground, fibrous ground, cavernous ground, combustible ground, pyritic ground and conductive ground.The second relationship is between the bench geology and blasting results. The blasting results discussed include: muckpile characteristics, remaining rock faces and blasting emissions. In this regard, some detailed insights and graphical examples are given for the influence of geology on blasting emissions, in particular, vibration, airblast and flyrock.A detailed description of the geological materials themselves can convey much useful information for blasting operators provided they are able to utilise this knowledge. Geologists are ideally suited to provide this description more effectively if they are familiar with the blasting process and the rock mass properties that influence blasting hazards and blasting results. It is also important to have clear statements of blasting objectives and associated operational targets, and this will maximise the likelihood of achieving the desired outcomes. The main aim of the paper is to highlight that geology is currently not fully utilised in the blasting process. In this regard, geologists are often not entirely aware of the blasting process and how they can contribute. The two significant relationships discussed above are integral parts of this process, and thus they are discussed as separate issues in the main body of this investigation.

Aug 22, 2011

By E. L. Evans

The historical development of South Yorkshire mining is traced and note made of the liability to generate spontaneous combustion of some of the seams which have been worked. The liability factor is analysed firstly as an inherent property in the material of a coal seam, and secondly as a circumstance of a situation in which access is provided for the air necessary to sustain oxidation. The geological settings in which incidents of heatings have been known to occur is discussed and conditions favouring a natural pre-disposition to spontaneous oxidation exposed, particularly the effect of argillaceous material overlying the seam. An extensive strata-dynamic study follows to demonstrate the situations in which stray air currents tend to impinge on readily oxidizable material. Prevention techniques are indicated as the identification of strata-dynamic situations in which air access to broken coal is induced and thereafter th operational action to seal off the voids which have been opened up so as to exclude air from the broken coal. Measures to reduce the tendency for ventilating air to short circuit across waste voids, and to obviate deflection of air into packs are outlined. The importance of face and roadway design features is demonstrated and the consequences of practices inimical to good control of spontaneous combustion are related. Discussions on means of detection and also on the sealant materials available are included.

May 23, 1905

By AIME AIME

ALFRED WILLIAM GAUGER ??Al" or &apos;?Doc" to his many friends in the coal and chemical industries- is known for his research talents and organizing ability. Appropriately the first public recognition of his technical ability was by the A.I.M.E. in the publishing of a paper by George A. Burrell and Alfred W. Gauger in the "Transactions" for the year 1916. "Al" Gauger was born at St. Paul, July 31, 1892. He graduated in chemistry at the University of Minnesota in 1914. A year later he began his initiation into the mysteries of coal mining when he joined the safety division of the U. S. Bureau of Mines at Pitts- burgh, serving from 1915 to 1917.

Jan 1, 1944

By J Graaf, R A. Murrell

Gold Fields Australia is constructing two major ventilation shafts at the Wallaby gold mine in Western Australia. The new ventilation shafts are required to facilitate the long term ventilation strategy for the mine, thereby allowing continued extraction of ore beyond 1000 m below the surface. The construction work has involved all of the challenges that shaft construction can throw up, including challenging geotechnical conditions, unexpected high water inflows and major circulation loss during pilot hole drilling for raise boring. An extensive geotechnical and hydrological investigation program was undertaken prior to awarding the shaft construction contracts. While most of the risks were identified, several proved to be much more challenging than expected. The shaft construction methods included conventional sinking into the fresh rock profile in each shaft, followed by raise bore pilot hole drilling and reaming. A headframe was constructed for the first shaft, which was sunk to 92 m with a stage suspended in the shaft to facilitate the concrete lining and provide rope guides for the kibble winding. Drawing from experience when sinking the first shaft, additional ground pre-conditioning was implemented for the second shaft, which was pre-supported with continuous piles to 28 m followed by sinking to 50 m using a crane instead of winders and a headframe. Following the conventional sinking through the weathered zone in each shaft, the shafts were completed using a raise bore. The first shaft utilised a riser pipe and rotary vertical drilling system (RVDS) with the second shaft having utilised a dual rotary rig for pilot hole drilling. This paper reviews the site investigations undertaken, construction methodologies applied, the results achieved and the lessons learnt.CITATION:Murrell, R A and Graaf, J, 2017. Shaft construction at the Gold Fields Wallaby mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 321–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

Approximately half of all the fuel energy used in the United states is now pro-vided by oil and natural gas. A persistent and rapid growth in energy demand during the last 3 decades has been absorbed largely by the liquid and gaseous rather than solid fuels. In 1948 the energy provided by coal was substantially the same as in 1920. Meanwhile, the use of oil and natural gas each had increased fivefold. On a per capita basis, the change is more significant. Coal consumption has dropped from about 6 tons per person to 4-1/2 tons, while oil has increased from 4-1/3 barrels to 14-1/3, and natural gas from 7,500 cubic feet to about 35,000. These facts would have only academic interest if the United States had unlimited supplies of all fuels. However, while the Nation&apos;s reserves of coal are adequate to meet our needs for centuries, those of oil and natural gas appear limited. It is obvious, therefore, that the security of our liquid-fuel position would be greatly enhanced if the supply could be based in an increasing degree on solid fuels, such as coal and oil shale, which make up more than 95 percent of our fuel reserves, instead of natural oil and gas. In addition, this would create new employment and help to stabilize the market for coal, which may be facing comparatively bleak prospects in the near future unless its position with respect to other fuels is improved.

Jan 1, 1950