Search Documents

By C. L. de Jongh

Fracturing of the rock caused considerable difficulties during the boring of a deep-level tunnel in hard rock. A pilot bore was suggested as a possible means of reducing the effect of the fracturing, and this possibility was investigated theoretically by means of a three-dimensional elastic stress analysis. Failure criteria were applied to the results of this analysis, and it was found that fractures predicted by the use of a simple criterion of limiting tensile macrostrain criterion agreed remarkably well with in situ observation. It was concluded that fracture could not be avoided and that a pilot bore was likely to aggravate tunnelling conditions.

Jan 1, 1978

By K. Morita, N. Sano

Thermodynamic properties of chromium oxides in molten slags are very important for optimization of stainless steel refining processes as well as reduction processes of chromium ores. The solubility of chromite into molten slags has been found to vary considerably with oxygen partial pressure and slag composition in former studies by the authors. In the present study, activity data and redox equilibria of chromium oxides measured under moderately reducing conditions, PO2= 6.95x10–11atm, at 1873 K are summarized. For the CaO-SiO2-CrOXsystem, the activity coefficient of chromium oxide increased with increasing basicity, and the optimized slag composition for stainless steel refining is assessed as that saturated with CaCr2O4and Cr2O3usingthe phase relations determined. On the other hand, the presence of MgO and Al2O3brings about different behaviour of chromium oxide activity and redox equilibiria and the 44 mass per centCaO-39 mass per cent SiO2-11 mass per cent Al2O3-6 mass per cent MgO slag is recommended toreduce the chromium oxidation loss in the practical stainless steel refining process at 1873 K. Keywords: chromium, activity, stainless steel, AOD, VOD, oxidation loss, redox, CaO-SiO2-Al2O3-MgO slag

Jan 1, 2004

By Richard A. Winters

In 1985 at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 9,400 acres of the 10,005-acre Duncan Creek Wilderness Study Area (ID-111-78) in order to evaluate the mineral resources. The study area is located in Owyhee County, 10, about 36 miles southwest from Bruneau, ID. No mining districts are in the study area, nor were any mines or claims recorded or found. The southern half of the area was covered by oil and gas lease applications, all of which were cancelled prior to June, 1985. No economic concentrations of minerals were found in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Duncan Creek study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By T. R. Ellis

The author attempted to concurrently apply the US Uniform Standards of Professional Appraisal Practice and the Australian VALMIN Code to a complex mineral property appraisal assignment. This led the author into many severe difficulties. These difficulties included the high standards needed in the work of others, and information and statements needed from the client. The exercise also highlighted many positive features of both documents. Some conflicts were found between the two documents. Implications and thoughts regarding the development of a set of US minerals appraisal standards are discussed.

Jan 1, 2000

By J. P. H. Steele, M. U. Ozbay

As mining operations progress toward tele-mining and autonomous procedures, the need for machine performance monitoring increases. Presently, through a combination of vision, sound, and other subjective observations, an operator attempts to optimize the mechanical excavator’s operation. As the operator is moved away from the face in the case of tele-mining or completely removed for autonomous operation, the qualitative sensory input is lost. This lost information must be replaced with quantifiable sensory input. Chip formation detection may be a suitable replacement sensory input. Chip formation can be predicted with high confidence (>80%) through the analysis of the load waveform associated with the bit/rock interface.

Jan 1, 2002

By Kenneth Gavin

Design practice for piles installed in Irish glacial till has developed in an ad-hoc manner, based on the results of un-instrumented load tests. This had led to designers using similar design parameters for both CFA and displacement piles. To address the concerns of industry a series of instrumented pile tests were performed by two Irish Universities. These tests summarized herein, revealed that CFA piles develop higher shaft resistance than piles driven in glacial till. However, they exhibit low base stiffness and the end bearing resistance that can be mobilized at acceptable pile settlement is low. The use of simple non-linear elastic design approaches to predict the load-displacement response is considered. The methods are used to predict the capacity of two large diameter CFA piles installed in glacial till. While the predictions were reasonably accurate at predicting the initial load-displacement of the piles, significant creep settlement developed at higher load levels. The cause of the creep settlement was investigated through the use of plate load tests and the consequences for pile design are discussed.

Jan 1, 2009

By O. W. Bilharz

INTRODUCTION ACID mine-water drainage is a serious problem with many mines in the Tri-State zinc and lead mining district. Particularly is this true when large volumes must be considered in unwatering old mines that have refilled with water which has dissolved the products of oxidation and has become chalybeate in character. The experiences discussed in this paper have to do specifically with the unwatering of a comparatively small area west of the town of Baxter Springs, Kans., where the pumping job was complicated by water of this type and where the extremely high sulphate content particularly effected that phase of mine drainage having to do with stream pollution. LOCATION, GEOLOGY AND HISTORY The Baxter Springs area of the Tri-State mining field is situated just west of the town of Baxter Springs and is a northeasterly extension of the main mineralized zones of the Oklahoma part of the district (Fig I). The mining area is traversed with well defined shear zones which provide easy circulation of ground waters and the ore bodies are found along these shear zones as localized enrichments wherever the structural conditions are favorable (Fig 2). The ore-bearing strata is Mississippian with an overlain capping of shale of Pennsylvanian age. This shale strata carries much pyrite and marcasite at its base and undoubtedly was a contributing factor to the subsequent high iron content of the water. The area originally contained a sulphide water which discharged as an artesian flow in springs within the town and gave Baxter Springs its name. These springs were famed for many years for their mineral water. This original sulphide water was first removed about 1917 and active mining was carried on west of the town during subsequent high metal price periods. Many small mines were opened, with each localized enrichment becoming a separate mine. During the depression mining ceased and all mines in the west Baxter area were allowed to flood. No serious effort was made to again unwater until higher prices caused from the demand for metal for World War II once more focused attention on this part of the field. ORIGINAL MINING RESULTS IN OXIDATION As plans for unwatering progressed, it soon developed that the mine-water pools had become strongly acid in character and carried large amounts of sulphates in solution. This occurred in the following way. When the original sulphide water was removed, shafts sunk, and mining carried on over a number of years, ferrous sulphate was formed by the spontaneous oxidation of the pyrite beds in contact with air admitted through churn-drill holes and mine openings. These products of oxidation can be seen today in the old mines of the district as crusts of crystalline sulphates

Jan 1, 1947

By Joel D. Hammond

Lightweight concretes date back to before the Roman Empire. The earlier concretes were made by combining a burnt lime for cementious material with pumice or volcanic rock for aggregate. Although structural value was limited due to its primitive nature, many structures were able to withstand the test of time. The rotary kiln expanded shale industry had a slow start that began around 1908. The industry was founded by Stephen J. Hayde of Kansas city, Missouri. Mr. Hayde noticed that the bloating effects of some aggregates were undesirable by the brick industry. Material of this type was considered waste and avoided in brick production, but he realized it had all the qualities and basic requirements for a concrete aggregate that would reduce weight and still retain structural value. It came into national attention by use in ocean-going vessels through a shipbuilding program undertaken by the united states Fleet Corporation. This research was brought about by the need to find a suitable material to replace high-grade plate steel due to a shortage created by World War I. The need prompted the government to supply the reserves that Stephen Hayde desired to continue and complete research into producing a uniform lightweight aggregate. His results pointed to the rotary kiln method for which he was granted a patent in 1918. One of the most famous and largest concrete ships built through this program was the U.S.S. Selma. Although the Selma

Jan 1, 1977

By G. Gaidajis

Sea water samples collected from coastal waters in the vicinity of the Stratoni mining operations, in North-Aegean Sea were analysed for dissolved metals and elements. The maximum concentrations observed were one to three orders of magnitude lower than the environmental limit which coincides with the quality of sea waters suitable for swimming purposes. The quality of the coastal sea waters are affected by the natural mineralization of the area and the urban activities drained through local small rivers, the past mining activities present in the sea bottom sediments in the form of disposed tailings, and finally by the presence of the adjacent Mill-Flotation Plant. The relative importance of the treated final effluents discharged from the mining operations is considered to be insignificant.

Jan 1, 2006

By D. A. Keefe, O&apos

The electrowinning of beryllium from beryllium oxide (BeO) using a molten-salt electrolyte composed of 56 LiF-37 BeF2-7 BeO (mole-percent) was investigated. Anodes made of porous carbon were found to be superior in current-carrying capacity and gave a lower cell voltage than other types of anode material tested. When porous carbon anodes were used) the resultant increase in anode area prevented anode passivation. The cell voltage was 3.3 volts) and electrode current efficiencies of 50 to 70 percent were obtained. The electrodeposited beryllium was recovered as beryllium powder or was coalesced to metal beads by heating to 1,300° C.

Jan 1, 1970

By Richard Curtis

Optimum Colliery is presently experiencing a shortfall of stripping capacity in order to meet its production requirements. Due to the long dragline procurement times, several alternative stripping methods were evaluated in order to alleviate this shortfall in the interim period. Based on the experience gained at the mine. The writer will discuss some of the important factors which influence dragline performance and show how these factors may by used in a theoretical approach to analyse various dragline applications.

Jan 1, 1990

By K Orth

The volcanic successions that host massive sulphide deposits are diverse in composition, facies types and facies relationships. They also show a variety of spatial and temporal relationships to mineralisation. In many examples, such as the Koongie Park Formation in Western Australia, the host succession includes more or less conformable syn-volcanic sills with peperitic contacts. Such sills can be an important source of heat for fluid circulation, influencing patterns of hydrothermal alteration and the location of co-eval and later mineralisation. The impact of syn-volcanic sills on the host succession depends in part on the initial porosity and permeability of the enclosing facies. The special properties of glassy pumice û being highly porous, permeable, and reactive û allow pumice-rich facies to preferentially focus hydrothermal fluid flow. However, the same properties promote early alteration and porosity reduction. Hence, the diagenetic and compaction history of pumiceous facies strongly influences their potential to host massive sulphide mineralisation. In contrast to pumice, dense glass has relatively low porosity, at least initially, and does not compact. Non-vesicular glass is a major component of submarine lavas, syn-volcanic intrusions and some volcaniclastic facies. However, especially in submarine settings, dense glass is commonly intensely perlitically fractured soon after eruption. The fractures greatly increase the porosity and permeability, locally accelerating diagenetic and hydrothermal alteration. In addition to false pyroclastic textures, altered perlite may exhibit false porphyritic textures. Silica- or feldspar-altered perlite kernels surrounded by intensely altered phyllosilicate domains can resemble phenocrysts in a fine grained groundmass.

Jan 1, 1999

By A. G. Royle

The reasons for constructing a model of an orebody for which both the parent population and the sampling distribution are known are discussed and details of the model are given. A brief summary of Matheron's theory of regionalized variables is included, with particular reference to his kriging estimators and their variances. Using the model, a comparison is then made between these kriging estimators and other commonly-used estimators. These are compared to find the one with the minimum variance, and an analysis is included to investigate whether any of the estimators is biased. Also included is a comparison between theoretical and experimental variances for some of the estimators.

Jan 1, 2014

By A. S. H. Kabir

Due to the high specific strength and excellent corrosion resistance, Ti-6A1-4V has been widely applied in aerospace industries. In this study, the welding performance of 3.2-mm and 5.1-mm thick Ti¬6A1-4V sheets was studied using a 4 kW continuous wave Nd: YAG laser. It is found that the use of filler wire, matching the parent metal composition, can bridge the joint gap and produce full penetrated welds up to a width of 0.6 mm without cracking. The laser welds were characterized in terms of the bead geometry, defects, microstructures, and hardness. With increasing joint gap, the percent porosity area increased, reaching just over 1% of the fusion zone area at a gap width of 0.6 mm for the 3.2 mm and 5.1 mm thick sheets. The maximum underfill depth in the Ti-6A1-4V laser welds was about 5% or 7% of the sheet thickness for the 3.2-mm and 5.2-mm thick materials, respectively, meeting the AWS D17-1 specification. The microindentation hardness was maximum in the fusion zone and sharply decreased through the heat affected zone until reaching the base metal value.

Jan 1, 2011

By K. Short

Today?s modern mining operations have literally dozens of applications and systems generating data whose information very often, are not crossed or centralized for operational decisions. In remote locations, the information and situation awareness is typically limited to the location itself. In addition, access to that information is limited to a small, select group of personnel that have received training on how to interpret the results. When the situation affects another area of the mine then information is relayed to the applicable areas involved. Few workers have time to analyze the situation thoroughly, to see how it affects the mines symbiotic relationship within all areas of production. If the capability to correlate and measure events and situations that affect your overall key performance indicators are not in place, the opportunity to identify process improvement becomes more difficult.

Feb 27, 2013

By B. M. Das, D. B. Cross

"In June 1983, the Computer Applications and Process Control Committee (CAPC) of the Canadian Institute of Mining and Metallurgy (CIM) circulated a questionnaire to coal mining, exploration and consulting companies in Canada to determine the industry's level of interest in holding a workshop-style meeting to introduce company personnel to ""state-of-the-art "" computer systems designed to carry out specific technical and management junctions. It was necessary to conduct the survey to determine the specific fields of application and the nature of training which are of most interest.Almost universally, the companies expressed interest in computer workshops and training for applications in the Canadian coal industry. The survey showed that all categories of personnel felt the need for some sort of training. Areas of specific interest identified were: exploration and geology, mine design, reserve calculations, coal mining technology, coal preparation, rock mechanics, ventilation, financial planning, and process simulation. The details of this survey together with an assessment of the significance of computer applications in the Canadian coal industry are presented in this paper."

Jan 1, 1986

By Junbiao Liu

Rutile is mostly produced from placer sands. Its beneficiation from primary deposits has rarely been investigated. However, there is interest in primary deposit because of the depletion of sand deposits. The Zaoyang deposit in China is the only rutile primary deposit currently mined. The plant employs a Tabling-Magnetic process which recovers only 20% Ti02 at a grade of 87%. This study shows that significant improvement on the recovery (52% at the same grade) can be achieved. This study includes a detailed mineralogical examination and the development of a processing flowsheet of the ore. The gangues are primarily amphiboles, garnets, zoisites, and chlorites. The liberation of rutile occurs at about 200 mesh. Gravitational, flotation, and magnetic separations are all employed in the process developed, depending on the mineral characteristics and experimental results. The flotations circuit utilizes benzyl arsonic acid to float rutile and sodium fluosilicate to depress the gangues. This is a new reagent scheme for rutile flotation.

Jan 1, 1989

By T. Johnson

Hydrometallurgical processes can be exceptionally corrosive. This is particularly true in acid leaching processes for copper, cobalt, nickel and rare earth elements. In the last five years, several large hydromet plants have been built in North America (Vale - Long Harbour, Baja Mining ? El Boleo and MolyCorp - Mountain Pass). Hundreds of storage tanks, extraction vessels and electrowinning cells along with miles of piping were designed and fabricated to withstand the aggressive environments inherent in these processes. One key element all three projects had in common was the extensive use of FRP in equipment design. As a material of construction, FRP provided equal if not improved durability relative to alternative corrosion resistant alloys at a considerably lower cost. This paper will highlight the extensive use of FRP in these three world scale projects and why it was chosen for each process.

Jan 1, 2013

By W. A. Hoyer

A pulsed high-energy neturon-induced spectral logging tool has been built and field-tested. The reaction of deuterium on tritium is used to generate pulses of 14-Mev neutrons. By detecting only the prompt gamma rays produced by neutron inelastic reactions in the formation, the presence and relative abundance of carbon, oxygen, calcium, silicon and other important elements may be ascertained from a gamma-ray spectrum. Gamma-ray spectra obtained in a shallow test well and in experimental field use show that it is possible to identify formations and their contained fluids. INTRODUCTION The penetrating gamma rays from naturally occurring radioactive elements in subsurface formations have been used for a number of years in well logging as a means of characterizing and distinguishing strata. Still another nuclear logging method which has been employed for some years consists of the bombardment of strata with neutrons and the measurement of the number of gamma rays produced by neutron capture reactions involving elements in subsurface strata.' Since one of the principal elements entering into capture reactions is hydrogen, the latter procedure essentially results in a hydrogen log, whether the hydrogen be in combined form in either oil or water; thus, the log gives an indirect measure of porosity. These methods, with various refinements, have been developed to such an extent that they have become routine procedures in formation evaluation. Neither gamma-ray logging nor conventional neutron logging, however, yields sufficient information to permit unequivocal identification of the mineralogic composition of formations, and neither method gives information which may be used for the positive identification of hydrocarbons in strata. Accordingly, a number of efforts have been made in recent years to gain additional information from nuclear logs. Brannon and Osoba have shown that it is possible to identify naturally occurring radioactive elements in subsurface formations by spectral analysis of gamma rays emanating from these elements. Such an identification is of value in the characterization of strata. A simplified form of spectral analysis of gamma radiation resulting from neutron capture reactions between elements in earth materials and bombarding neutrons has been used with some suc- cess under favorable conditions to differentiate between petroleum and water. This method relies upon the relatively high energy of gamma radiation from neutron capture by chlorine and, in effect, furnishes a chlorine log. In areas in which interstitial water is of sufficiently high salinity, this log can give valuable information on water saturation and, thus, indirectly on hydrocarbon saturation. Still another approach to obtaining more information by nuclear techniques is "activation logging", in which certain elements yield short-lived radioactive isotopes on neutron activation and, thus, can be detected by gamma-ray spectral analysis. From the standpoint of determining by nuclear logging methods the mineralogic composition of strata and the presence or absence of hydrocarbons, it is essential that information be obtained on the presence and relative amounts of several elements such as carbon, oxygen, hydrogen, calcium, silica and others. Some elements, such as hydrogen, chlorine and sulfur, can be determined by spectral analysis of gamma radiation resulting from neutron capture reactions."" Others — carbon and oxygen, for example — do not enter readily into capture reactions but do yield gamma rays of characteristic energies from inelastic scattering reactions with high-energy neutrons. Accordingly, the latter reactions are of particular interest as a means of identifying hydrocarbons in subsurface strata. Several years ago it was recognized that information requisite to the identification of subsurface strata and of contained fluids could be obtained by pulsed operation of a subsurface neutron generator and associated gamma-ray detector. It was contemplated that pulsed operation would be effective in discriminating in time that gamma radiation which results predominantly from inelastic scattering reactions from that gamma radiation arising from neutron capture reactions. Accordingly, research was continued and construction of such a device was initiated. Although many problems were encountered, they were solved successfully. The following sections describe the tool which has evolved, its performance and the results which have been obtained with it to date. THEORY OF OPERATION OF NEUTRON-INDUCED GAMMA-RAY SPECTRAL LOGGING TOOL THEORY OF INDUCED NUCLEAR REACTIONS Of fundamental importance is the fact that an element, when bombarded with neutrons, emits gamma radiation of energy characteristic of that element. In theory, therefore, an element may be identified by

By Harvey P. Knudsen

This paper describes the results of a comparative study of the geostatistical ore reserve estimation method over three conventional methods; the polygon method, the inverse of the distance squared (IDS) method, and ELIP which is similar to IDS. Each method was evaluated on its ability to accurately predict individual block grades for one bench of the Pima Nine, located near Tucson, Arizona. Results at the Pima Mine indicate that the geostatistical method is no better nor worse in predicting block grades and total tonnage than the ELIP or IDS methods in contrast, the polygon method is clearly inferior. All of the methods would have given better results if geology had been included in the block model. At already producing mines ELlP or IDS may be good choices since they involve substantially less cost in computer time. For prospective or new properties, the geostatistical model is more attractive, due to its ability to construct confidence limits on the estimates.

Jan 1, 1976