Search Documents

By Sidney A. Swensrud

The 24-in. crude-oil line. and- the 20-in. petroleum-products line, built as a war emergency by the United States Government and running from points in Texas to the New York-New Jersey-Philadelphia area, were constructed only because of the inability during the war to continue nor-inal ocean tanker movements from the Gulf Coast to the East Coast. The postwar disposition of these lines may be considered as one of the important problems of the postwar readjustments in the oil industry, if not the most important one. In the first place there appear to be many complications in keeping the lines in crude-oil or petroleum-products service. This conclusion was reached also in a study by T. E. Swigart, President of Shell Pipeline Corporation.' Since the lines are too largc for any one company to utilize, and since it appears likely that a surplus rather than a deficiency of tankers will exist after the war, most companies probably will feel that they can achieve lower costs and more satisfactoiy results from the resumption of tanker movements to the East Coast rather than by endeavoring to take over or utilize the capacity in the large pipe lines under some tariff-rate structure. As for using the lines for making deliveries to the middle west or central eastern areas, it would appear that when the war is over and normal transportation arrangements can be resumed, there will be no need of any extra capacity for such deliveries. Therefore, the War Emergency lines could be utilized for this purpose only if privately owned pipe lines and other transportation facilities were to be displaced. Against this rather unprepossessing prospect for use in petroleum or product service is the fact that at or near the source of the lines lie the greatest developed gas reserves in the world, for much of which there is at present no satisfactory market outlet; and at the other end of the lines lies one of the greatest concentrations of population in the world, which is not now served by natural gas. These who have been fortunate enough to use natural gas can have little doubt of its desirability as a domestic fuel. An analysis of the market potentialities and comparison with other areas where natural gas is being distributed, and where it has displaced manufactured gas, makes it seem clear beyond question that the full capacity of both of the large-diameter lines could be fully utilized in this service, and this without creating any undue drain upon the gas reserves of the nation. On the basis of an estimated capacity of roo to 120 billion cubic feet per year, the gas that might be marketed through these lines would amount to only 3 to 4 per cent of the total con-

Jan 1, 1944

By Andreas Hucke

For the roadway design in the German hard coal mining industry, an advanced combined planning system has been applied during the past 20 years. The German mining industry is working with single entry roadways system. After first longwall passage the roadways will be stabilised with side wall building material packages. Later this roadway will be used again for the second retreating longwall. The intention of the implementation of several different design methods for the planning of the roadways is to enhance the reliability of the results. On one hand the planning system uses numerical simulation and physical modelling in addition to analytical and empirical methods. On the other hand in-situ monitoring and analysis during the roadway development will be used to verify and calibrate the numerical and physical models. Especially before the implementation of new support elements in underground, this system is suitable and reasonable because the new support elements will be tested in the physical and numerical simulation prior to cost intensive underground tests. The interaction between the numerical and physical modelling in comparison with underground monitoring and analysis during development and the later use of roadways will be shown with some examples. The first example shows a rock bolted rectangular roadway which will be mined at both sides of the roadway. Different support and roadway building material package systems are investigated under various stress conditions. The results are utilised to optimise the roadway support and the roadway side package systems. The influence of different points in time of the installation of several support elements in a combined arch and bolted roadway is shown as another example. Two different types of support systems are compared within the physical models. These models are used as a base for ongoing numerical analysis and simulation to find out the ideal point of time to assemble the different support elements. The last example handles the influence of slickensides in the roof of arch shaped roadway on their stability. Different slickenside positions and densities are investigated and classified.

Jan 1, 2006

By Harrison Schmitt

THE definitions of the terms commonly used in connection with metamorphism at elevated temperature near igneous contacts are re-examined. As the study of tactite zones associated with igneous contacts progresses, more and more emphasis is put on the localization of the ore by structural forms. The generally early age of the silicates and late age of the sulphides is well established. Postsilicate structural deformation is likely to localize ore bodies. The silicates are often replaced by the ore minerals. We may not be far from proving that the elements involved in the formation of silicate aureoles are merely normal "volcanic" emanations, that silica, lime, magnesia, and alumina and probably soda and potash are likely to undergo local transfers only. The work of Newhouse suggests the agents of the formation of sulphides in deposits of various classifications are the volcanic emanations.

Jan 1, 1947

By Moussa Wone, William Levy, Christopher Caruso, Zachary Spera, Thomas Hennings, Richard Stacy Kinchen, PE Joel Kantola

"Owners constructing new combined sewer overflow (CSO) systems increasingly seek to have project design lives of 100 or more years in response to the growing size, complexity, and cost to construct and operate these systems. However, a codified and universally accepted approach to achieving this goal in the United States does not currently exist since service life prediction is a relatively new technical field. This paper discusses how the 100-year design life requirement was met for the design of tunnels, drop shafts, and diversion structures in the DC Clean Rivers Program (DCCRP). The authors identify some commonly referenced publications, present the testing framework used by the program manager to characterize the CSOs, review the design criteria used to guide the 100-year design life development, and establish guidelines to be considered by program managers and designers when implementing similar extended design life requirements in other CSO control programs.INTRODUCTIONLike many older cities in the United States, the sewer system in the District of Columbia consists of both combined sewers and separate sanitary sewers. When the capacity of a combined sewer is exceeded during storm events, the excess flow, which is a mixture of sewage and storm water runoff, is discharged to the District’s receiving water bodies (Anacostia River, Potomac River, and Rock Creek) and tributaries through outfall structures. This excess discharge during storm events is called a combined sewer overflow or CSO. A total of 53 CSO outfalls for the combined sewer system are listed in DC Water’s National Pollutant Discharge Elimination System (NPDES) Permit issued by the U.S. Environmental Protection Agency (EPA). The DC Clean Rivers Program (DCCRP) will reduce the number of CSO outfalls into the Potomac and Anacostia Rivers and decrease flooding in DC neighborhoods during extreme rain events by capturing, storing, and conveying diverted CSOs to the Blue Plains Advanced Wastewater Treatment Plant."

Jan 1, 2016

By Raphael França Assumpção

O aço inoxidável duplex (AID) vem sendo considerado uma excelente alternativa para aplicações que requerem alta resistência à corrosão e alta resistência mecânica. Portanto, a microestrutura e as propriedades dos aços dúplex permanecem como temas de grande interesse. Para este proposito, estudou-se o efeito da laminação a morno em um aço inoxidável duplex. O foco deste trabalho foi o AID 2205 que é um dos tipos mais comuns de AID. O objetivo deste estudo é avaliar o comportamento eletroquímico do AID 2205 laminado a morno no ambiente de íons de cloretos utilizando medidas de polarização potenciodinâmica. O aço inoxidável dúplex foi laminado a morno à 600°C para 60 e 80% de redução na espessura e submetido a testes eletroquímicos. As amostras apresentaram uma excelente resistência à corrosão em solução de NaCl 3,5%. Apesar da existência de certa similaridade entre os valores de potencial de circuito aberto e potenciais de pites obtidos para todas as amostras, o número de pites observado foi maior na amostra CF, seguida pelas amostras com 60 e 80% de redução.

Oct 30, 2017

By S. Kauvosaari, M. Olofsson, O. Haavisto, M. Kosonen, J. Martikainen

The target in grinding circuit operation is usually to maximise the throughput and energy efficiency while keeping the product particle size on an optimal level for downstream operations. Furthermore, feed ore variations in size and hardness need to be compensated in order to stabilise the process. This is a challenging task for any circuit and requires good instrumentation, combined with careful control design. This study investigates the control of a two-stage iron ore grinding circuit with an AG and pebble mill at LKAB Kiruna KA3 concentrator in northern Sweden. A new control approach based on multivariable model predictive control (MPC) is designed, implemented and evaluated for the circuit. Additionally, advanced instrumentation including a volumetric charge measurement for grinding mills is utilised. The MPC control approach starts with step tests that are used to model the effect of manipulated variables (MVs) like feed rate, water addition and primary mill speed on controlled variables (CVs) such as final product particle size, power consumption and volumetric charge of the mills. In the control implementation phase, the models are then utilissed together with current process measurements and known operating limits to predict optimal future changes for the manipulated variables in order to reach the desired process output values. It is shown that the new control approach improves the stability of the circuit and reduces energy consumption. Keywords: Model predictive control, grinding, optimisation

Jan 1, 2020

By J. F. Bryson

Instantaneous outbursts of coal in underground workings have occurred frequently in various coal fields in Nova Scotia; British Columbia; Canada; South Staffordshire, England; and the states of Washington, Virginia, West Virginia and eastern Kentucky in the United States. Such outbursts in eastern Kentucky have been called "mountain bumps " because they are more likely to occur under mountain cover than elsewhere, but recently they have become generally known as "coal bumps." The eastern Kentucky coal field has been troubled by these outbursts since 1923. Many men have been injured and killed, and the morale of the workmen in the vicinity of such outbursts has been affected to such an extent that mine production has suffered for a considerable period following each outburst. Such phenonlenal occurrence in any coal field naturally has led to discussion as to the cause and means of prevention. In the eastern Kentucky field, local mine officials, workmen, mining engineers, and many others have offered many ideas as to the cause and many methods of prevention have been suggested, and tried without success. Some of the plans were either practically or economically unsound and in general impossible to follow. To enumerate all the suggestions would require a large volume. One cause mentioned was that they might be due to gas under high pressure, as in Lower Silesian mines, and the remedy reeommcnded was to drain the gas by drilling holes into a suspected area. A hole 30 ft. long was drilled into a 60-ft. pillar to allow the gas to drain off, hut the pillar bumped the next day. Realizing the importance of obtaining the best information available on coal bumps, the writer, with the permission of the Harlan County Coal Operators' Assoeiation, invited Mr. George S. Rire, Chief Mining Engineer of the U.S. Bureau of Mines, who had investigated bumps in several countries, to conduct an investigation of coal bumps in this field. Mr. Rice, by permission of the Director of the G.S. Bureau of Mines, accepted the invitation, and it was the writer's privilege, in company with

Jan 1, 1936

By J. F. Bryson

Instantaneous outbursts of coal in underground workings have occurred frequently in various coal fields in Nova Scotia; British Columbia; Canada; South Staffordshire, England; and the states of Washington, Virginia, West Virginia and eastern Kentucky in the United States. Such outbursts in eastern Kentucky have been called "mountain bumps " because they are more likely to occur under mountain cover than elsewhere, but recently they have become generally known as "coal bumps." The eastern Kentucky coal field has been troubled by these outbursts since 1923. Many men have been injured and killed, and the morale of the workmen in the vicinity of such outbursts has been affected to such an extent that mine production has suffered for a considerable period following each outburst. Such phenonlenal occurrence in any coal field naturally has led to discussion as to the cause and means of prevention. In the eastern Kentucky field, local mine officials, workmen, mining engineers, and many others have offered many ideas as to the cause and many methods of prevention have been suggested, and tried without success. Some of the plans were either practically or economically unsound and in general impossible to follow. To enumerate all the suggestions would require a large volume. One cause mentioned was that they might be due to gas under high pressure, as in Lower Silesian mines, and the remedy reeommcnded was to drain the gas by drilling holes into a suspected area. A hole 30 ft. long was drilled into a 60-ft. pillar to allow the gas to drain off, hut the pillar bumped the next day. Realizing the importance of obtaining the best information available on coal bumps, the writer, with the permission of the Harlan County Coal Operators' Assoeiation, invited Mr. George S. Rire, Chief Mining Engineer of the U.S. Bureau of Mines, who had investigated bumps in several countries, to conduct an investigation of coal bumps in this field. Mr. Rice, by permission of the Director of the G.S. Bureau of Mines, accepted the invitation, and it was the writer's privilege, in company with

Jan 1, 1936

By Kurt Oakes, Paul Worsey, Braden Lusk, Tony Brasier, Jerry Chambers, Scott Crabtree, Randy Wheeler

Destructive wave interference has been studied in theory for many years. In application however, limited information can be found. Recently, circumstances have enabled a multidisciplinary team to utilize electronic detonators and seismograph analysis to create destructive wave interference in an underground production blasting application. Springfield Underground, located in Springfield, MO, in conjunction with Orica, ETI, White Industrial Seismology, and the University of Missouri – Rolla has shown the ability to use destructive wave interference in underground blasting to reduce ground vibrations directly above.

Jan 1, 2006

By I. E. Teymenson, L. A. Bakhvalov

Irrational usage of mineral commodities leads to depletion of natural resources and various ecological violations in natural environment. Fulfilment of a number of measures and strategic decisions by given problems requires a correct forecast of trends of social-economic systems. For solving the task of long-term forecasting special procedures, considering Kondratyev’s big cycles of world conjuncture, have been embedded into algorithms of unknown parameters identification and recovering of factors of different countries mineral resources production and consumption models. In the paper the classification of long cycles types, existing forecasting algorithms on the basis of Kondratyev’s ‘long waves’ or ‘K-waves’ and the modified algorithm, developed by us, which allows to reduce time and financial expenses and to improve the forecast quality, are presented. Furthermore, the article includes several forecasts of mining branch corrected models factors, received by us, permitting complex prognosis of economic and social development of different scale and control level systems. In the paper workability of proposed forecasting algorithms on the base of ‘K-waves’ and adequacy of created models to researched processes are proved.

Jan 1, 2003

By E. Ghali, A. D. Bas

There is a lack of electrochemical studies of oxidized gold ores since the majority of previous studies were conducted with sulphidic gold ores. In this study, the influence of agitation and iron oxide minerals, i.e. magnetite, hematite, and maghemite on gold leaching was investigated by means of galvanic and passivation phenomena. Cyclic voltammetry studies of Roasted Gold Ore (RGO) in de-aerated electrolyte have shown one oxidation and one reduction reaction while three oxidation and one reduction peaks were observed with gold electrode. Galvanic coupling results by Zero Resistance Ammeter (ZRA) mode indicated that magnetite showed a negative effect on gold dissolution while maghemite and hematite showed a positive effect, relatively, as a result of higher galvanic corrosion rates. Generally, gold dissolution was found to increase in the initial 15 minutes. Increasing agitation speed from 100 to 400 rpm resulted in higher galvanic corrosion rates for RGO, magnetite, and maghemite electrodes, while 250 rpm was found to be optimum for hematite electrode. Passive products such as silver and iron-oxide were identified by XPS and SEM-EDS analysis, respectively.

Jan 1, 2015

By Patridge A. C

Hydrocyclones have widespread use as classifiers in applications such as mine fill preparation and coal preparation. A fundamental conflict often exists between recovery of all of the valuable material and maintaining the quality of the product. This conflict is a result of a portion of the feed material passing through the cyclone, effectively without undergoing any classification. This paper describes an investigation, undertaken as an undergraduate project in mining engineering at the University of NSW (Brook, 1994), into aspects of cyclones in which supplementary water injection is used in an attempt to reduce the amount of misplaced fine material reporting to the coarse product and hence improve the overall classification efficiency. In particular, the study concentrated on the effects of different modes of water injection. Two methods of introducing wash water into the cyclone body were investigated. A series of tests were performed on a laboratory hydrocyclone having provision for radial water injection at different levels through small orifices in the wall of the conical section, and a preliminary study was made of the performance of a novel cyclone in which the conical section had walls of a permeable polyethylene, permitting a uniform introduction of wash water over the entire surface.

Jan 1, 1995

By D. Michaud, C. Bazin, S. Lévesque, L. Pérez-Barnuevo, H. Longuepée

In recent years, with the emergence of Geometallurgy, a great effort has been made to characterize ore resources as early and accurately as possible, to allow better design and a more efficient operation of mineral processing circuits. In this context, core logging plays an important role, since drill cores provide the first insight into the ore characteristics. However, to satisfy geometallurgical requirements, traditional core logging does not suffice. New tools and methodologies need to be developed for the automation of core logging and the acquisition of mineralogical data better related to mineral processing performances. In this paper, a methodology for the geometallurgical characterization of drill cores is proposed, based on the drill core textural patterns. Textural pattern is defined here as the macroscopic spatial arrangement of minerals. The Mont-Wright iron ore deposit (Quebec, Canada) is used as a case study. The first part of this work aimed at analyzing the potential link between the iron ores textural patterns observed in drill cores and their response to ore processing, namely comminution and concentration. Preliminary results show similar performances in terms of energy consumption and heavy liquid separation for samples showing the same textural pattern. In the second part, this work seeks to develop a methodology for the automated identification of drill core textural patterns by the application of digital image analysis and discriminant function analysis. The results obtained show that this methodology is able to discriminate between the textural patterns identified at Mont-Wright with a good rate of success. Therefore, this work lays the foundation for the development of a new drill core characterization tool, which would allow for the early prediction of the iron ore behaviour during mineral processing through the identification of drill core textural patterns.

Jan 1, 2016

By Zhou Junwu, Sun Chuanyao, Wang Fuli

"In this present paper, the authors introduce the artificial neural networks into the modeling of the industrial flotation process, integrating information technology, control theory and intelligent optimizing method to flotation technology. The new idea gives a new way to solve the difficulty in this field, and therefore brings the study on the automatic control of flotation process in China into a new start.The Radial Basis Function (RBF) network, featuring a quick learning speed, is one of the feedforward neural networks. It has attracted much attention from automatic control recently for its implementing the nonlinearity mapping through adjusting the parameters of the nonlinearity transfer function. One of the online adaptive learning algorithm—the nearest neighbor-clustering algorithm, which can automatically determine the number of hidden units, has been implemented in the MATLAB programming language in this paper, laying the foundation for the flotation models.The relation model between ore pulp characteristics and reagents consumption has been proposed using the RBF networks based on the industrial lead rougher flotation of lead & zinc ore, and the simulation has been conducted in the laboratory with the results matching the samples data very well. The Xilin Lead & Zinc Mine Flotation Process Intelligent Consultation System of Reagents Consumption, which suitable for industrial process, has been developed. The reagents consumption advised by this system would stabilize the flotation process, and increase the recoveries. It could be used for providing the technological consultation to flotation operators in site, and for training new operators."

Jan 1, 2003

By James Wonneberg, William Edgerton

"Today’s underground construction megaprojects are tremendous feats of engineering on a massive scale, excavating through ground conditions once thought impossible, using new and innovative contracting practices. But one important truth remains unchanged; projects are built by people. What separates winning projects from the rest? Great people, working in great organizations. In straight-talk fashion this paper sets forth fundamental differences between good project leaders and bad ones, on topics ranging from client relations, design management, and scheduling, to use of the whiteboard, and everything in between. Broadly applicable to all corners of project delivery, this paper will resonate with project leaders from around the world and help identify skills necessary to succeed in the management of underground facilities. A NOTE FROM THE AUTHORS This is a training document, and not really a “paper” per se. We have attempted to tackle some big and potentially complex topics using bite-sized paragraphs, each of which are intended to promote thoughtful introspection and dialog. So please feel free to skip around, or even set this document down while you reflect on your own personal experiences, tactics, and philosophies. We have found that providing examples of “what not to do” is oftentimes more instructive than simply listing “what to do”, hence the Good/Bad format of this document. Please note that “PM” refers loosely to anyone on the project management team not just the “Project Manager”. We also wish to preface this with the following cautionary statements: • The authors do not pretend to be the “Good PM” in all cases. In fact, we’re almost certainly the “Bad PM” for some. We aim to improve on those areas. • It has been said that “The only real training for leadership is leadership.” (Antony Jay) We all started somewhere, and nobody has 20 years of experience on day one. • Converting this text into some sort of prescriptive checklist would be a disservice to the evolution of project management. Our world – and our awareness of it – is constantly changing. We must always be open minded to new ideas and different perspectives on project delivery."

Jan 1, 2016

By Tuncel M. Yegulalp

This final report contains the results of all work performed under BOM Grant J0333905. A preliminary systems analysis of coarse-particle coal slurry pipelines as a haulage method for longwall mining systems was performed. Two exhaustive literature surveys on state-of-the-art longwall mining and slurry transport technologies were prepared. Two representative longwall systems were designed, one with conventional haulage and one with slurry haulage. These two systems were then compared on the bases of cost, safety, and reliability. The conclusions were that for the case of a two-face longwall mine, a coarse slurry transport system does not have a clear-cut cost advantage over a conventional (conveyor-hoist) system. However, indications were that a cost advantage could occur under different analytical conditions such as: (1) a larger scale mine, (2) if intangible benefits were quantified, and (3) if new generation technology rather than currently available technology were applied to the study. Budget and time constraints prevented exploration of these conditions.

Jan 1, 1982

By Frederick C. Rhyner

The United States government sponsored the construction of a new vehicular bridge over the Diyala River in Bubriz, Iraq. This paper describes the geotechnical engineering for design and construction of drilled shaft foundations for this bridge. An Iraqi geotechnical engineering firm made borings and laboratory tests while analysis and design recommendations were provided in the United States. Despite the severe challenges of engineering in a war zone, excellent cooperation was the key to a successful effort. Three drilled shafts designs were necessary to accommodate the different subsurface conditions: a) medium-compact to compact sands, b) stiff to hard clays and c) mixed soil profile. The alpha and beta methods were used to estimate capacities for a conservative design, recognizing that quality control during construction might be less than what is normally provided in the United States. Iraq has a high seismic risk and LPILE was used to estimate the drilled shaft response during earthquake loading conditions. Settlement estimates were made using FHWA methods. Construction was carried out entirely by local Iraqi firms, despite the challenges of working in an active conflict area.

Jan 1, 2009

By Gerald H. Luttrell, Lance Christodoulou, Jaisen N. Kohmuench, Michael J. Mankosa

The efficiency of the froth flotation process has long been known to be strongly dependent on particle size. For sulfide minerals, good recoveries are typically achieved in industrial flotation circuits for particles in the 30 to 200 µm size range. Particles outside this critical size are typically lost in industrial operations and rejected to tailings streams due to inherent constraints associated with the physical interactions that occur in the pulp and froth phases of conventional flotation equipment. In response to these limitations, a series of experimental studies were conducted to determine whether particles previously lost as tailings could be economically recovered using a suite of novel flotation technologies developed for upgrading ultra-coarse and ultra-fine particles in the industrial minerals industry. For the case of ultracoarse particles, a fluidized-bed flotation system called the HydroFloatTM separator was tested. The data obtained using this novel flotation device in both laboratory- and pilot-scale trials showed that good recovery of previously lost sulfide values up to 850 µm diameter could be achieved. Similarly, for ultrafine particles, a high-intensity cavitation-based column cell was tested. This technology, which utilizes highshear contacting of slurry and gas, was capable of recovering valuable ultra-fine sulfide that were previously lost due to the low capture efficiency of conventional flotation processes. The objectives of this article are (i) to describe the unique operating principles of these two advanced flotation technologies and associated ancillary classification equipment, (ii) to present laboratory- and pilot-scale experimental test data showing the metallurgical benefits of the proposed novel flowsheet for sulfide tailings processing, and (iii) to provide a generic cost-benefit analysis of the proposed system for recovering lost values in existing sulfide tailing streams.

Jan 1, 2016

By S. Ripke

Between 2002 and 2004, the performance of a six million ton per year iron ore beneficiation plant dropped significantly. In a classic case of “who done it,” was it the mine, the concentrator, an ore change, or something else? While average annual final product grade decreased 8% (indicated by an increase in silicate gangue from 2.76% to 2.99%), the weight recovery also decreased by 8% (from 37.92% to 34.79%). This represents a loss of 832,000 tons of iron ore worth about $16 million for the two year period! The concentrator had been optimized to produce a high grade wet concentrate as feed to the dry side of the plant. But, did optimizing an individual unit operation’s grade give the best overall plant performance? In this paper, the investigation and solution to this mystery will be revealed.

Jan 1, 2007

By Alexey T. Kovalev, Irina A. Khabarova, Valentine A. Chanturiya, Igor Zh. Bunin, Elizaveta V. Koporulina

"The paper presents new theoretical and experimental results about mechanisms of disintegration of mineral complexes and structural transformations of the sulfide surface under high-power nanosecond electromagnetic pulses (HPEMP). The heated gas outflow from nanosecond breakdown channels of sulfide minerals under HPEMP is considered. It is shown that the gas outflow from channels can be an additional destructive factor in the processes of the electric pulse discharge disintegration of mineral complexes. It is shown that the effect of HPEMP changes chemical surface composition and, respectively, technological properties of pyrrhotite and pentlandite. Morphology and elementary composition of new micro- and nanoformations on mineral surface of pentlandite and pyrrhotite have been investigated using up-to-date methods of SEM/EDX and Scanning Probe Microscopy. Preliminary electropulse effect on mineral products before flotation allows producing optimal conditions for flotation separation of pentlandite and pyrrhotite owing to forming the new nanophases and defects on the surface of sulfides.IntroductionThe effectiveness of High-Power Nanosecond Pulses in the disintegration and liberation of fine disseminated mineral complexes and the recovery of micro- and nanoparticles of precious metals from refractory ores was demonstrated in [1, 2]. Possible mechanisms of selective disintegration were considered in [1-3]. It has been shown both theoretically and experimentally that electric breakdowns can play an important role in the nanosecond pulsed treatment of milled minerals (e.g., semiconductor sulfides and quartz with particle sizes of 100 µm to 2-3 mm) that are carriers of finely disseminated gold and other valuable components. Electric discharges in such minerals are accompanied by a destruction of integrity in the form of breakdown channels and the formation of a system of cracks around these channels [3]. The development of the domains of induced cracks around the channels is determined by the pressure of evaporated material in the breakdown channel. Upon an instantaneous energy release in a channel (nanosecond discharges), the change in its transverse size and in the gas density and pressure in the channel is determined by (i) the radial motion of the evaporation wave, (ii) the radial expansion of the channel, and (iii) the heated gas outflow from the channel. The evaporation wave moves with a speed on the same order of magnitude as the speed of sound (or greater) and travels a distance of around the initial channel radius, i.e., a much smaller distance than the breakdown channel length."

Jan 1, 2011