Search Documents

By Robert A. Cummings, Madan M. Singh

In April 1984 a subsidence depression formed directly beneath a two-story frame residence, near Linton, IN, causing 2 ft of separation between the floor and walls, and damaging both the foundation and interior of the building. The Office of Surface Mining undertook the rehabilitation of the area under its emergency response program. This paper describes the investigation performed to determine the cause, severity, and extent of the problem. Abandoned mine workings were found approximately 55 to 60 ft below the house. Based on the findings, remedial measures were prescribed. An abatement program consisting of grouting the mine voids was recommended, and specifications prepared. These were implemented, and the area has been successfully stabilized.

Jan 1, 1986

By L. B. Berger

From time to time the Bureau of Mines receives requests for information and advice regarding the safety of using internal-combustion engines operated on butane fuel as prime movers for haulage and other purposes in mining and tunneling. The purpose of this, circular is to discuss the properties of butane and to present data in regard to the possible use of this fuel in underground operations. Published information on the use of commercial butane as a fuel for internal-combustion engines indicates that, insofar as performance is concerned, butane may be utilized satisfactorily and efficiently for this purpose. However, the introduction of a volatile, inflammable material such as butane into confined spares such as mines or tunnels would create potential fire and explosion hazards that should be given due consideration by those concerned with the promotion of safe practices.

Jan 1, 1944

By H. Kenworthy

Small batches of fluorspar flotation concentrates were made into nodules and pellets on a laboratory scale. Several of these were rated acceptable by laboratory evaluation methods. The most satisfactory pellets were produced by mixing fluorspar with about 12.5 percent of water, by weight, and 4 percent of organic binders. These binders) for the most part) originated from petroleum and wood-pulp industries. They were generally difficult to handle and were not easily incorporated with the fluorspars tested. Most of them seemed to have an aversion for damp fluorspar and had to be forcibly mixed with the fluorspar; which was then formed into pellets by pressure. Substitution of fuel oil in varying amounts in the binders enhanced the mixing and penetrating qualities of these binders but at the same tire tended to make the pellets more porous. Tall oils performed the same function to a lesser degree and usually decreased the water absorbency of the finished pellets. Heat-treating temperatures to set up these binders were moderate -about 5000 F. for 30 to 50 minutes was usually enough for both drying and heat treating. Nodules made with 1-1/2 to 2 percent of bentonite as a binder were easily mixed and formed. They required a high degree of heat (about 1,500° F.) to develop their strength and were quite water-absorbent when finished. Two fluorspars were examined for weight and fluorite loss after heat treatment at similar temperatures. Both showed a definite wej.ght and analytical loss of fluorite. Bentonite was used also as a binder to successfully nodulize finely ground oxides of iron, manganese, and nickel.

Jan 1, 1951

The fundamental objective of mine plans are usually to maximize the mine profit by extracting ore at the lowest possible cost over the mine life while some technical constraints are satisfied. Since the costs associated with the operation of trucks and shovels as resources are significant, determining the optimum number and allocation of these resources is an essential issue. This paper presents a Mixed Integer Linear Programming (MILP) model to determine the optimum number of shovels and trucks required to meet the short-term plan?s goals. Also, the model takes into account the allocation of trucks and shovels to mining faces. This model minimizes operational costs, while attempting to meet the production demand and to satisfy technological constraints. This paper also analyzes the operations of trucks and shovels in an open pit mine using ARENA simulation software.

Jan 1, 2012

By F. A. Rutledge

The Bureau of Mines Investigated the Copper Bullion claims at Rua Cove on the east coast of knight Island in Prince William Sound, Alaska, during November-December 1948 and March-April 1949. This project was part of the Bureau of Mines program for developing critical and strategic minerals in Alaska, Mineralization at the copper deposit on the Copper Bullion group of claims is mainly pyrrhotate and chalcopyrite, confined to a northeast-trending shear zone in the greenstone 2,000 feet northwest of Rua Cove. The property has been partly developed by two adits, by a number of crosscuts from the upper adit, and by several diamond-drill holes.

Jan 1, 1953

By Angelo dos Reis Magalhães

Brazilian companies have adopted in recent years new management practices to remain competitive. Specialized consulting in asset management progressively creates or adapts new techniques in order to increase availability and reduce manufacturing costs, maximizing profits. New engineering concepts were acquired and implemented by executives in all business segments. Techniques, such as FMEA, RCM, LCC, Pas 55, Reliability studies by Monte Carlo simulations, among others, have become increasingly recognized as important tools to enhance managerial performance. Besides these techniques, this study suggests the importance of adequate structuring of a lubrication program, as a critical success factor for the reliability of any asset. Through a case study developed with a company in the mining sector, this work proposes the development of a master plan for lubrication based on three pillars: People, Equipment and Management system. Practices and care with lubricants, hydraulic fluids and coolant, until its point of application, shall be evaluated to ensure a correct contamination control and a high level of assets availability. This discussion sheds light onto other benefits of this process, including occupational health and safety; ergonomics; environment and sustainability.

Jul 31, 2018

By Catharine L. VanOmmeren

Emulsion quality characteristics such as shelf life, handling, and sensitivity are critical to the end-user. It is therefore important that the consumer be prepared to ask his supplier specific questions. To do so, he needs to have a basic understanding of what an emulsion is and how emulsion properties can affect safety, performance, and environmental impact. The criteria to be covered include: energy, velocity, sensitivity, minimum priming, shelf life, pumpability, effect of AN quality, over-the-road handling, and formulation The consumer will learn how each of these properties can directly affect him. The information will enable him to set minimum standards in product selection, blending, and application.

Jan 1, 1989

By T. Foster

The continuous operation of decanters in the mining industry relies heavily on the use of synthetic flocculants. Today, as plants seek to lower production costs by increasing throughput it is necessary to obtain optimum performance from the flocculant. Factors affecting such optimization include charge and molecular weight selection, and efficiency of mixing the highly viscous polymer solution with the feed slurry. Beyond maximizing dilution of the solution, the last factor is often ignored. This paper describes a series of calculations, based on fundamental transport theories, that have been used to describe flow conditions within decanter feed wells and to help select flocculant addition points. Examples are shown for the case of hydroxamated polyacrylamide flocculants in the Bayer Process, where proper selection of the addition points can result in lower flocculant dosage and better control of the decanters.

Jan 1, 1996

By S. H. Ash

NO MORE important question has come before the coal-mining industry in many places, especially in the anthracite region of Pennsylvania, than prevention of stream pollution by mine drainage. Available information on acid mine drainage in the anthracite region of Pennsylvania indicates that a pollution problem must be solved in any program of anthracite mine drainage. The major problem concerns satisfactory disposal of the daily average mine-water discharge of 327,000 gallons per minute (g. p. m.), or 472 million gallons per day (g. p. d.), containing a free-acid load of 431 tons or a total acid load of 934 tons a clay as H2S04. This report indicates the scope of the problem and gives some suggestions concerning its solution.

Jan 1, 1951

In 1996, O&K Orenstein and Koppel Inc. announced big plans to increase its presence in the US mining market. Even though the company, a part of Ger- man-based O&K Mining GmbH, has been in the United States for about 100 years, it has lived in relative anonymity. That despite being one of the largest makers of hydraulic mining shovels and excavators in the world. The plan must be working. In the 14 months through December 1996,O&K increased its sales to surface mines and quarries in the United States by 250'70, according Rolf Weber, company president. "In the next five years, we anticipate total revenue from our US operations will grow from the current $50 million to $200 million," he said. "Toward that end, we have concentrated our efforts on the supply of reliable, high-output machinery and responsive service after the sale."

Jan 1, 1997

By Victor A. Phillips

A series of strips of a Ni-12.7 at. pct A1 alloy were Prepared containing cubical y'(NisAl) precipitates with edge lengths from 60 to 500A. A particle-free solution-tveated strip was included for cornparison. They weve cold-rolled 95 pct and the effects of particle size on the isochronal (1/2 hr) annealing behavior between 300° and 950°C studied (by hardness and light and electron microscopy). It ulas inferred that the particles deformed with the lnatvix becoming lamellae which remained coherent. Comparison with published data fov pure nickel showed that aluminum greatly re-tavded softening and recrystallization, but it made little difference whether or not particles were present. The presence of pakticles led to a heterogeneous distribution of precipitates after annealing at 700" to 750°C. Recovery was not detected. Recrystallization occurred by the growth of new grains into unrecrys-tallized material. In a previous study by the author,' the growth of Ll2-type ordered yl(Ni3Al) precipitates was followed in Ni-12.7 at. pct A1 alloy as a function of aging at 600" and 700°C. The particles were showo to be cubical in shape in all sizes from 50 to 3000A and remained coherent. This work was used as a guide in preparing the starting structures for the present study of the effect of these particles on the annealing behavior of heavily cold-rolled strip. Another question of present interest was whether dislocation and particle hardening were additive, since the structures before rolling ranged from solution-treated to peak-aged to overaged. Also, precipitation might occur on annealing after cold-rolling. Reference may be made to other papers2"5 for previous work in this relatively unexplored field and only some recent work will be mentioned her:. phillips2 studied the effect of deformable 0 to 590A-diam cobalt particles on a Cu-3.23 pct Co alloy rolled 95 pct and found that the particles, which rolled out into thin lamellae, impeded softening and recrystallization. Tanner and servi3 likewise studied the annealing of cold-swaged Cu-2 pct Co alloy containing 150A-diam particles and found impeding effects. Haessner et a1.,4 on the other hand, found that incoherent 2-p-diam non-deformable particles of B4C (0.04 vol pct) tended to increase the rate of recrystallization of copper rolled up to 95 pct reduction. They attributed this to the formation of new grains at the particle interfaces. Humphreys and artin' found that nondeformable silica particles in copper rolled to 30 pct reduction accelerated recrystallization if the particle spacing was large and retarded it if the spacing was smaller. Haessner et a1 4 also studied a rolled Ni-Cr-A1 alloy; however, the particles of y'(Ni3Al)-type precipitate were not put in before rolling, but separated during the isothermal annealing at 750°C. No previous work appears to have been carried out on the effect of y' (Ni3A1) particles on the annealing of Ni-A1 alloy. Hornbogen and ICreye7 redetermined the solubility c of aluminum in nickel as a function of temperature T and showed that it was given by c = 32.6 exp(-1940/RT). This relation gives aluminum solubilities of 15.1, 14.2, 12.0, and 10.7 at. pct at 1000°, 900°, 700°, and 600°C, respectively. The phase precipitated from the nickel-rich solid solution is fcc y1 (Ni3A1) which has a Cu3Au -type ordered structure8 and remains ordered up to 1000°C.B EXPERIMENTAL PROCEDURE The alloy used was identical with that used before. Chemical analysis showed 6.27 wt pct (12.71 at. pct) Al, the principle impurities being 0.065 pct Fe, 0.022 pct Co, 0.020 pct Cu, and 0.004 pct C. Bar stock of 1 in. diam was cold-swaged to % in. diam, cold-rolled to 0.300-in.-thick strip, and annealed at 900°C in dry hydrogen. It was cold-rolled to 0.100-in. thickness and solution-treated for 1 hr at 1000°C while sealed in a quartz tube in argon, quenching in iced brine with the aid of a device to snap off the nose of the tube. Lineal analysis gave an average grain size of 0.055 mm. Pieces of strip were aged at 700°C in vacuo for 30 min, 51/4 hr, and 1 week to produce nominal average particle widths of 60, 150, and 500A, respectively, as known from the previous work.' The average diamond pyramid hardness was determined. The heat-treated strips were rolled from 0.100 to 0.005 in., a reduction of 95 pct, and the rolled strips stored at about -5°C. Small pieces were annealed within 1 week for 30 min at temperatures from 300° to 950° ±2°C in a horizontal vacuum furnace. Strips were withdrawn into a cooling zone, giving an estimated initial cooling rate from 950°C of about 50°C per sec. Average diamond pyramid hardnesses were determined on a lightly electropolished spot on the surface of each strip using 300-g load. Each point on the softening curves represents a separate annealed specimen. Sections containing the rolling direction were examined by optical metallography. Selected specimens were electrothinned to the center plane' and examined by transmission at 100 kv in a Siemens Elmiskop I electron microscope. It is well-known that changes in the structure tend to occur when a deformed strip is electrothinned below a thickness of a few hundred angstroms, although this is less serious with a material such as nickel which has a high melting point, and also is apt to be less serious when particles are present. Observations were nevertheless confined to thicker regions of the foils with estimated thicknesses over 1000A. No changes were observed due to beam exposure.

Jan 1, 1968

Session 1 ? Intro to MiHR ? Business Case for Aboriginal Inclusion ? Overview of the Mining HR Guide for Aboriginal Communities ? Two presentations of Programs featured in the Guide ?? The RAP Program from NWCC ?? First Nations Youth Employment Program PDAC-MM Session 2 ? Presentation from MAC ? Taking up the AFN Corporate Challenge ? Presentation on Mastering Aboriginal Inclusion in Mining About MiHR Who we are: ? National Sector Council for the Minerals and Metals Sector ? 18-person Board of Directors ? 100+ Industry Leaders volunteer on our project committees ? PPP - Funded by HRSDC and industry What we do: ? Identify national HR challenges and opportunities for the minerals and metals industry ? Create national solutions through collaboration, partnerships and Synergy

May 1, 2009

By James R. Craig

The Central and Southern Appalachians were the major sources of gold in the United States throughout the first half of the 19th century and have continued to yield gold to the present day. Small amounts of gold were probably extracted by the Indians and the Spaniards but the first documented report of gold in the region was made by Thomas Jefferson who found a four pound lump of gold ore, which yielded 0.85 troy oz., in the Rappahannock River of Virginia in 1782. Gold was subsequently discovered in North Carolina between 1793 and 1799, in Virginia in 1806, in South Carolina in 1827, in Georgia in 1829 and in Alabama about 1830 (Becker, 1894-5; Pardee and Park, 1948). The gold belts of the Central and Southern Appalachian Piedmont and Blue Ridge Provinces are shown in Figure 1. The superimposed circles indicate the mount of production from some of the more productive and well known areas. Although North Carolina produced far more gold than the other states, the most significant concentrated area of production is the Dahlonega District in Georgia which yielded more than 500,000 troy ounces. After discovery, gold production increased rapidly as shown in Figure 2. Production was at its maximum between 1830 and 1852 with combined totals generally exceeding 30,000 troy ounces per year. Production dropped sharply after the California gold rush in 1849 as experienced miners moved westward in search of bigger and easier stakes. After the Civil War briefly halted gold mining in the Appalachians, production rose to an average of about 8,000 ounces per year from 1865 until 1878 and to an average of about 13,000 ounces per year from 1881 until 1915 when it again fell to near nil (Pardee and Park, 1948). Minor resurgences occurred in the 1930's and 1940's. Although there has been no reported production in recent years, it is likely that "weekend panners" still remove hundreds of ounces from streams annually. The total reported production for the area through 1959 is in excess of 2.5 million troy ounces.

Jan 1, 1981

By P Hatherly, A Melkumyan, D Wyman

Chemical species distributions in rock sequences can be modelled using Gaussian processes (GPs) to predict the weight percentage between known data points. This method can be improved by dividing the modelled area into regions of different mineralogy. In the context of many iron ore deposits, marker shales give the initial guidance of where these regions may lie. These shales give rise to distinctive peaks in the natural gamma downhole logs, which are conventionally identified by hand. A GP method has been developed to automate this task.Once the appropriate boundary has been located on the basis of shale occurrences, chemical assays from exploration drill holes are used to find the exact boundaries of interest. These boundaries divide the drill hole stratigraphy into regions of different mineralogy, each of which display their own distinct correlations between the main elements and oxides (Fe, SiO2 and Al2O3). Iron ore shows a negative correlation between Fe and Al2O3, but in banded iron formation (BIF) there is a positive correlation between these species. Similarly, SiO2 and Al2O3 have a positive correlation in the shales and ore but a negative correlation in the BIF. Correlations obtained within ore-, BIF- and shale-dominated regions are therefore better than those obtained using the entire log and can be used to improve the results obtained when modelling.

Sep 26, 2011

By George J. Conroy

Results of a long-term program of electrical parameter measurement in under-ground coal mine working sections, performed by The Pennsylvania State University under U. S. Bureau of Mines sponsorship, are utilized as the basis for an analysis of the electrical energy requirements during operation. A model section is hypothesized, developed from the average or most representative characteristics as determined from tabulations of the measurements. Performance factors of the model section's machine complement are then analyzed, particularly with regard to the energy required per ton of raw coal cut and delivered from the section. Results are given in kilowatt-hours per ton.

Jan 1, 1977

By Carter A. J, Miller D. M, Holder N. H M, Van Aswegen P C

The Harbour Lights Mine situated at Leonora in Western Australia, mines a refractory sulphidic gold ore. The main sulphide minerals are pyrite and arsenopyrite. Due to the association of gold with the pyrite and arsenopyrite, gold recovery is not amenable to the normal cyanidation process.A pyrite/arsenopyrite flotation concentrate is produced at Harbour Lights. This concentrate has been stockpiled for the past two years.A bio-oxidation process (BIOX«)* to treat refractory gold flotation concentrates has been developed by GENMIN in South Africa. Harbour Lights acquired the technology from CRL BIOX« Pty Limited in Brisbane, to treat the refractory gold concentrates.

Jan 1, 1992

? Develop a six year capital budget for future emission controls at Western Springfield Power Plant that would provide long-term operating certainty

Jan 1, 2005

By R. G. Cawthorn

The earliest authenticated scientific report of the occurrence of platinum in rocks from the Bushveld Complex appears to be by William Bettel on 10 November 1906. Thereafter, prospecting of the chromite-rich rocks for platinum proved frustrating. I suggest that the resurgence of interest shown by Dr Hans Merensky in 1924 resulted from his realization that newly panned platinum had a different grain size from that in the chromite layers and indicated a different source rock, which he located, and it became known as the Merensky Reef.

Jan 1, 2007

By H. E. Miard

"IntroductionIT HAS BEEN SAID, with good reason, that the future of the coal mining industry, in our mountainous regions at least, depends on ability to extend operations successfully to depths greater than those reached until now. However, at many points, Nature has given definite hints that trespassing there could be fraught with very un-pleasant possibilities, unless the intruder be governed by a series of rigidly observed principles. In the coal mines of British Columbia, so far, bumps have taken place only at the Coal Creek colliery, but there they gave ample evidence of the extent to which they can hamper underground operations. Some of these manifestations have also been experienced at the McGillivray Creek colliery, in Alberta, at Carbonado, in Washington, and at Sunnyside, in Utah.Cognate phenomena, known as 'air blasts', have been experienced also in some deep metalliferous mines in British Columbia. Such occurrences were responsible for three fatal accidents at the Le Roi and War Eagle mines, near Rossland, in 1916 and 1917.In more or less disturbed coal fields, another form of stress release, equally detrimental, has been still more generally experienced than have been the bumps. Coal outbursts have taken place at Morrissey and Coal Creek, in the Crow's Nest Pass district, and at Cassidy, South Wellington, and the Nanaimo Reserve colliery, on Vancouver island. Manifestations of this kind have been made the subject of intensive study in European countries where they occurred on a really impressive scale, which must not be construed as meaning that some of our own outbursts did not approach a comparable magnitude."

Jan 1, 1953

By O. A. Carson

"IntroductionTHE ZINC-BASE die casting alloys in common usage contain approximately 4 per cent aluminum as the major alloy element. In addition, they contain about 0.05 per cent Mg .and may• have a small amount .of copper. These are usually the only •elements intentionally present.Small amounts of some impurities have been shown to have a deleterious effect on the properties of these alloys and therefore the impurities are kept low by starting with '99.99%' zinc.The reasons for holding the aluminum content at 4 per cent are not clear. Some statements appear in the literature that higher aluminum increases the brittleness, but probably the chief reason was the relative price of zinc and of aluminum when 4% alloys became firmly established. At that time, aluminum was three to four times the price •of zinc on a weight •basis. Recent prices, roughly equivalent per lb., make aluminum considerably cheaper than zinc on a volume basis and suggest that increased aluminum content would result in a decrease in the cost per piece due to the lower density of the alloy.Little information could be found in the literature and, therefore, it was decided to determine some physical properties of the higher aluminum zinc-base alloys made from high-purity zinc."

Jan 1, 1953