Search Documents

By Saman Khaleghparast, Naj Aziz, Jan Nemcik, Guanyu Yang

"More than 25 years of uninterrupted research on ground support technology for underground mines has been undertaken at the University of Wollongong. This research has resulted in significant findings on tendon characteristics and strength properties. The paper focuses on the development of the fourth generation of cylindrically shaped shear test apparatus for assessing tendon performance in shear. This shear apparatus is known as the MK-IV Double Shear Box or Naj Aziz Double Shear Box (NADSB), and is based on the experience gained from the development of previous versions of rectangular double shear boxes. The new NADSB is circular in shape and is fitted with a truss system, which permits friction free shear testing of tendons across joint planes. A series of double shear tests were carried out on a number of cable bolts commonly used in Australian mines, both plain and indented wires, under varied pretension loads. The results were compared with similar test results using rectangular shaped double shear apparatus, with and without friction across joint faces. The significance of wire surface roughness and increased initial pretension loads are discussed and conclusions made, suggesting that indented wires are inferior in shear compared with plain cable bolts. The general test procedure of the NADSB is described and different concrete reinforcement techniques are reported. The influence of external and internal confinement of the concrete medium blocks in a circular double shear box contributed to consistent test results with a minimum of lateral and axial cracks occurring in the host medium.INTRODUCTIONThe use of long tendon ground support elements (cable bolts) is now a common practice in modern underground coal mines, hard rock mines, tunnels and other underground structures. Due to their material properties cable bolts contribute significantly to the overall ground reinforcement provided by a support system. Cable properties in tension and shear are in many cases vital to maintaining a safe and productive underground environment. Accordingly, tension and shear properties must be assessed accurately using both valid and reliable methods.Load transfer property testing of tendons has been studied over several decades with much of the early research focused on the pull and shear testing of solid rock bolts and hollow bolts (like Swellex and split set tube bolts), as these elements were used extensively at this time. It was not until the 1970’s that the use of cables for ground reinforcement developed, and as such highlighted the need to extend load transfer property testing to include shear strength of cable bolts. Initially, the discarded hoisting ropes were used for ground support in metal mines, particularly in stopping wall support and then late in 1980’s cable tendons began to use in coal mines."

Jan 1, 2019

By P. W. Bridgman

DURING the war, the Navy undertook the construction, under my direction, of an experimental gun embodying features designed to lessen the cost and time of production. These experiments were initiated after representations as to their, desirability had been offered by myself, by the Naval Consulting Board, and by the National Research Council. The first drawings were made in June, 1917, and the experiment was completed in November, 1918. For the sake of clearness it will pay to recapitulate briefly the fundamental idea of gun construction. It is well known that if a hollow cylinder is subjected to internal fluid pressure, the maximum stress occurs in the inside layers, the outer parts carrying much less than their due share of the stress. This inequality of stress is more pronounced the thicker the walls of the cylinder. If such a cylinder is pushed to the elastic limit, failure in elasticity will take place long before the outer layers have reached the limit of their capacity. Economical use of the material would demand, however, that all parts of the cylinder reach the limits of their capacity simultaneously. This may be brought about, at least in cylinders of not too great thickness, by producing in. the inner layers an initial compression, and in the outer layers an initial tension. The effect of internal pressure is at, first to relieve the compression of the inside layers, while increasing the tension of the outside layers. If the initial stresses are properly distributed, all parts of the cylinder will reach their elastic limits simultaneously, thus giving a cylinder of maximum strength for its weight. In gun construction as hitherto practiced, this initial distribution of stress is produced either by winding the inner tube with wire, a common English practice, or by shrinking hoops over the inner tube, which has been the standard American practice. Either process is long and expensive, particularly with the larger guns, 12- or 14-in., which require

Jan 2, 1920

By W. R. Reed, J. P. Rider

"The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) recently developed a series of models using computational fluid dynamics (CFD) to study airflows and respirable dust distribution associated with a mediumsized surface blasthole drill shroud with a dry dust collector system. Previously run experiments conducted in NIOSH’s full-scale drill shroud laboratory were used to validate the models. The setup values in the CFD models were calculated from experimental data obtained from the drill shroud laboratory and measurements of test material particle size. Subsequent simulation results were compared with the experimental data for several test scenarios, including 0.14 m3/s (300 cfm) and 0.24 m3/s (500 cfm) bailing airflow with 2:1, 3:1 and 4:1 dust collector-tobailing airflow ratios. For the 2:1 and 3:1 ratios, the calculated dust concentrations from the CFD models were within the 95 percent confidence intervals of the experimental data. This paper describes the methodology used to develop the CFD models, to calculate the model input and to validate the models based on the experimental data. Problem regions were identified and revealed by the study. The simulation results could be used for future development of dust control methods for a surface mine blasthole drill shroud. IntroductionIn surface mines, production drilling is an essential process in blasting to fracture the hard rock overburden for removal. During the process, considerable amounts of respirable dust are produced. Past sampling at the shroud area of blasthole drills had documented time-weighted-average respirable dust concentrations ranging from 8.68 to 95.15 mg/m3 (Organiscak and Page, 1995) and 1.04 to 52.30 mg/m3 (Listak and Reed, 2007). These high dust concentrations, which may contain silica, can lead to respirable dust overexposures for the miners working nearby. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is ultimately fatal.Two basic methods are used to control drilling dust: a wet suppression system or a dry collection system (Cecala et al., 2012). Dry drilling techniques using a dust collection system are preferred in rural mining locations where a constant water supply is not available, and in the case of rotary drilling where water is associated with accelerated bit wear due to bearing degradation and hydrogen embrittlement. In addition, dry drilling eliminates freezing-related issues with water in colder climates. Dry dust collectors are highly effective at removing dust, especially the finer material, as long as they are properly operated and maintained (Listak and Reed, 2007; Organiscak and Page, 2005)."

Nov 1, 2016

By James A. Lewis

It is the purpose of this paper to show the importance of sand characteristics, when combined with other physical data, in evaluating production obtained by secondary recovery operations, and to indicate the benefits to be gained from the application of these principles to primary production. Introduction During the past 10 years there has been a growing interest within the industry regarding the movement of fluids through oil reservoirs. A number of research projects have been directed toward the development of the physical laws governing this movement. In the period 1933 to the present, correlations between laboratory analysis of cores, reservoir fluids and well performance have been established and have been applied to successful secondary water-flooding recovery operations; and to the completion, production, reconditioning and evaluation of wells in new fields. The application of these data to water-flooding, either natural or artificial, is comparatively new, but the principlcs involved were set forth in 1880 by John F. Carll,1 who said: The flooding of an oil district is generally viewed as a great calamity, yet it may be questioned whether a larger amount of oil cannot be drawn from the rocks in that way than by any other, for it is certain that all the oil can-not be drawn from the reservoir without admission of something to take its place. If one company owned all of the wells drawing upon a pool, and had accurate records of the depth and characteristics of the oil producing stratum in each well, it is quite possible that some system might be devised by which water could be let down through certain shafts, and thus the rocks be completely voided of oil and left full of water. As it is, however, no systematized plan of action can be adopted. The careless handling of one well. by which water is let down to the oil rock, may spoil several others belonging to different parties. A clashing of interests at once arises and is likely to result in disaster to the whole district. In judging of the probable effects of the intro-duction of water into any particular oil district several things are to be considered. (1st) The time of flooding—whether early in the progress of development, while yet a large percentage of oil remains unexhausted or at a later period after the supply has suffered from long continued depletion. (2nd) The structure of the rock—whether regular and homogeneous throughout, or composed of fine sand inter. bedding connected and irregular layers of gravel, sometimes lying near the top and at others near the bottom. (3rd) The shape of the area being flooded. (4th) The position of the point at which water is admitted. in relation to the location of the surrounding wells still pumping oil. (5th) The height (which governs the pressure) of the column of water obtaining admittance. (6th) The duration of the water supply. Although we may take exception to part of Carll's reasoning, particularly " and thus the rocks be completely voided of oil and left full of water," we must give him credit for pointing out the increased effectiveness of water encroachment in displacing oil from a sand and for his recording six of the present seven considerations necessary for evaluation of production of oil by water

Jan 1, 1942

By James A. Lewis

It is the purpose of this paper to show the importance of sand characteristics, when combined with other physical data, in evaluating production obtained by secondary recovery operations, and to indicate the benefits to be gained from the application of these principles to primary production. Introduction During the past 10 years there has been a growing interest within the industry regarding the movement of fluids through oil reservoirs. A number of research projects have been directed toward the development of the physical laws governing this movement. In the period 1933 to the present, correlations between laboratory analysis of cores, reservoir fluids and well performance have been established and have been applied to successful secondary water-flooding recovery operations; and to the completion, production, reconditioning and evaluation of wells in new fields. The application of these data to water-flooding, either natural or artificial, is comparatively new, but the principlcs involved were set forth in 1880 by John F. Carll,1 who said: The flooding of an oil district is generally viewed as a great calamity, yet it may be questioned whether a larger amount of oil cannot be drawn from the rocks in that way than by any other, for it is certain that all the oil can-not be drawn from the reservoir without admission of something to take its place. If one company owned all of the wells drawing upon a pool, and had accurate records of the depth and characteristics of the oil producing stratum in each well, it is quite possible that some system might be devised by which water could be let down through certain shafts, and thus the rocks be completely voided of oil and left full of water. As it is, however, no systematized plan of action can be adopted. The careless handling of one well. by which water is let down to the oil rock, may spoil several others belonging to different parties. A clashing of interests at once arises and is likely to result in disaster to the whole district. In judging of the probable effects of the intro-duction of water into any particular oil district several things are to be considered. (1st) The time of flooding—whether early in the progress of development, while yet a large percentage of oil remains unexhausted or at a later period after the supply has suffered from long continued depletion. (2nd) The structure of the rock—whether regular and homogeneous throughout, or composed of fine sand inter. bedding connected and irregular layers of gravel, sometimes lying near the top and at others near the bottom. (3rd) The shape of the area being flooded. (4th) The position of the point at which water is admitted. in relation to the location of the surrounding wells still pumping oil. (5th) The height (which governs the pressure) of the column of water obtaining admittance. (6th) The duration of the water supply. Although we may take exception to part of Carll's reasoning, particularly " and thus the rocks be completely voided of oil and left full of water," we must give him credit for pointing out the increased effectiveness of water encroachment in displacing oil from a sand and for his recording six of the present seven considerations necessary for evaluation of production of oil by water

Jan 1, 1942

By Thomas P. Goslin

T e mechanization of industry to reduce labor costs and to improve product quality is affecting he scale industry as it has affected many other industries. With increased emphasis on higher production rates many operators are experiencing difficulty in overcoming production problems where weight is a factor. Unfortunately, the scale industry has not shown the development over the last twenty-five years that other instrument industries have. For centuries the balance scale has been the standard and the workhorse of most weighing operations. In recent years considerable effort has been applied to designs to make balance scales more acceptable to industries employing automatic or semi-automatic processes. For the most part the designers have not attempted to replace the basic scale but toautomate functions of material handling and human judgement. Modern dump scales, for example, will accept material from a conveyor until a preset amount of material is on the scale, At this time the scale turns off the conveyor, dumps the load of material and repeats the operation with any desired timing. These improvements have helped industry. Even the scale observer has been replaced with devices which observe the scale reading and operate on weighed objects according to their weights. In spite of' the application of automation to the material handling, the balance scale has not been completely satisfactory. One reason for this is fairly evident when one considers the construction of the scales. Inherently, they are slow devices because of the inertia of the beams. The beam scale, primarily a static measuring device, is at the best limited to slow dynamic measurements.

Jan 1, 1958

Development of a New Dry Density Separator for Fine-Grained Materials

Sep 13, 2010

By V. Shumila, T. Butler

Microseismic monitoring systems listen to a rockmass and record ground vibrations associated with brittle rock fracture. Modern systems record continuously and can identify as many as one thousand small and possibly larger magnitude events occurring each day from induced stress change and redistribution. This paper presents examples of the real time use of microseismic information in mining applications. It shows how alerts can quickly identify large magnitude events or unexpected clusters of seismicity and how seismic re-entry protocol can help to improve safety decisions. Additionally, newly developed advanced analysis techniques applied to mine seismic data sets are shown including the use of clustering methods to see into a cloud of seismic data to identify significant activity and quantify possible planar features. The use of source parameter trend analysis is shown to be a beneficial method for interpreting changes in relative stress levels. Seismic moment magnitude distributions are analyzed using the TGR (Truncated Gutenberg Richter) and TMD (Tapered Moment Distribution) methods to estimate bvalue and expected maximum magnitude. Seismic hazard analysis is shown as a useful way to simplify a dataset and highlight seismic hot spots. The rockmass response to excavation is a complicated spatial and temporal process and microseismic monitoring is a method that can be used to help understand the location and mechanics of failure occurring in the rock ultimately helping to improve safety and productivity at a mine site.

Jan 1, 2015

By Luke Keeney, Stephen Walters

"The start up of a new mining and metallurgical facility is a crucial step in the life of any mining project. The mining industries record is poor when evaluating processing plant operation relative to design capacity predictions made during feasibility studies. Multivariate geometallurgical orebody characterisation, using principle component analysis, is a method developed for improving predictive processing performance models during feasibility stages of mine development. This paper outlines the application of multivariate geometallurgical characterisation to the Cadia East deposit located in New South Wales, Australia. Cadia East is a low grade high tonnage copper-gold porphyry system in advanced stages of feasibility analysis. A dataset of ~32000 measurements and 150 comminution parameters (A*b and BMWI) has been used to develop class-based characterisation and modelling methodologies. The results of this study outline the development of class-based ore characterisation and provide a technique for analysing and interpreting large and complex geometallurgical datasets for prediction and optimisation of processing performance. The results enable sophisticated population modelling to be conducted which displays deposit scale processing variability, aiding circuit design specifications and predictions during feasibility studies.INTRODUCTIONA feasibility study is the major technical report on which the decision to proceed to production and on which financing is based (Shillabeer & Gypton, 2003). The mining industry’s record is not very good when actual construction time, costs, and operating performance are compared to the projections made in feasibility studies (Ballard, 1983; Gypton & Ward, 2000; Gypton 2002). A study by McNulty (1998) found that of 41 mineral processing and chemical plants built between 1965 and 1995, only 56% achieved design capacity within two years of commissioning and three were closed after failing to achieve design capacity within 36 months of start up (Shillabeer & Gypton, 2003). McNulty (1998) related this underachievement and failure of start up performance to the use of innovative process technology without appreciating and managing technical risk. Factors contributing to technical risk include inadequate pilot plant testing, scaled up prototype equipment without backup, design flaws and poorly understood complex process chemistry."

Jan 1, 2009

By G. Azimi, K. K. Varanasi1, A. T. Paxson, R. Dhiman, H. -M. Kwon

Hydrophobic materials that are robust to harsh environments are needed in a broad range of applications. Although durable materials such as metals and ceramics, which are generally hydrophilic, can be rendered hydrophobic by polymeric modifiers, these materials deteriorate in harsh environments. Here it is shown that a class of ceramics comprising the entire lanthanide oxide series, ranging from ceria to lutecia, is intrinsically hydrophobic. Their hydrophobicity is attributed to their unique electronic structure, which inhibits hydrogen bonding with interfacial water molecules. In addition, this work demonstrates that these ceramics sustain hydrophobicity even after exposure to high-temperature environment (1000 °C for 2 h in air). It is envisioned that this class of robust hydrophobic materials will have far-reaching technological potential in various industrial applications, where water repellency and dropwise condensation are desirable.

Jan 1, 2014

If the communication/tracking system of an underground mine is severely damaged in a large mine accident or explosion, a surface based seismic system could be the only available tool for locating any trapped miners. This paper documents a field test of a seismic system at a room-and-pillar coal mine in Eastern Kentucky. Testing was performed at 6 different depths (450, 575, 750, 1175, 1525 and 1700 ft) above the mine. For each location underground, the miners pounded a ?set? of 5 ?repetitions? on the roof with each repetition being about one second apart. Over the 3 day field test, 63 sets of underground miners? pounding were detected by the seismic system at depths up to 1175 ft and at horizontal offsets up to 890 ft. Also during the testing, the observed signal strength generated by pounding with a crib blocks was seen to average 180% stronger than the observed signal strength generated by pounding with a sledgehammer. Ultimately, this field test was very successful and definitively demonstrated the ability of the seismic system to detect potential trapped miners? pounding up to a depth of 1175 ft.

Feb 23, 2014

By R. A. Metz, Willard C. Lacy

Survival of the mining industry as a viable economic entity in the United States is being seriously threatened by declining grades of ore reserves, rising operational and capital costs, and increased governmental taxes, restrictions, and subsidizing of third world competition. Discovery of major high-grade deposits is becoming increasingly unlikely. International competitiveness of the U.S. deposits will depend upon 'Yankee Ingenuity,' innovations in mining methods, metallurgical treatment, and financial arrangements, and a viable national strategy. This will require not only effective management for control of operations, but management that encourages breakthroughs in technology, financing, labor relations, and in public and governmental understanding. The mine geologist and the exploration geologist both have important roles to play in all aspects of this fight for survival of the industry.

Jan 1, 1992

By Carlton D. Hulin

The usual concurrence in time and space of intrusive igneous activity, favorable structural disturbance and mineralization, which is so manifest in the mineralized district necessarily indicates a close interrelationship between these events. Evaluation of available evidence leads to the recognition that an appreciable time interval exists between the emplacement of the igneous intrusive and the formation of associated ore deposits. During this interval known portions of the intrusive are completely solidified, highly differentiated magma facies are injected as dikes, and important faulting occurs, which may fracture and shatter the solidified intrusive body. The highly differentiated dike types could only have originated in some deep portion of an underlying plutonic body that had reached an advanced stage of magmatic differentiation. Appearing after these dikes, the mineralizing solutions may likewise be presumed to have originated at great depth. Certainly no source for these solutions can be found in near-by portions of the intrusive igneous body. The association of igneous intrusives and clustering ore deposits must be recognized as resulting from structural control. The emplacemerit and the subsequent solidification and cooling of the intrusive set in operation forces that are responsible for the favorable structural disturbances that control the mineralized district. The emplacement of the body of fluid magma weakens the crustal rocks to the extent that failure due to strains originally present in the rock body may occur. Faulting of any type and of any magnitude may be the result. Subsequently, owing to the change of state from fluid magma to crystalline granitic rock, volume decreases approximating 10 Per cent may Occur, with resultant shrinkage and collapse within the rock body. Following solidification, thermal contraction, induced by cooling of the rock body, causes a further volume reduction of 6 per cent. This thermal contraction, extending over a lengthy period of time, results in a succession of minor fault movements. These small fault movements, occurring progressively throughout the period of mineralization, are responsible for maintaining the permeability of the rock body, without which access of the mineralizing solutions and the formation of the ore deposits of the mineralized district would be impossible. Introduction A proper understanding of the causes that have localized our mineralized districts should be of considerable value to geologist and engineer alike. under current conditions the known ore reserves of productive mining camps are being rapidly depleted. Although ore of the future will be derived in part from deposits now known and from Ore bodies that are still to be discovered within the limits of productive mining districts, in part at least it must come from mineralized districts whose existence or importance yet remain to be recognized. The mining geologist is thus faced with two problems of paramount importance: (I) the location of new ore bodies within known mineralized areas and (2) the location of new mineralized districts within whose confines, previously unknown, valuable Ore deposits may occur. Any contribution to our knowledge concerning the causes for the localization of mineralized districts

Jan 1, 1949

By Carlton D. Hulin

The usual concurrence in time and space of intrusive igneous activity, favorable structural disturbance and mineralization, which is so manifest in the mineralized district necessarily indicates a close interrelationship between these events. Evaluation of available evidence leads to the recognition that an appreciable time interval exists between the emplacement of the igneous intrusive and the formation of associated ore deposits. During this interval known portions of the intrusive are completely solidified, highly differentiated magma facies are injected as dikes, and important faulting occurs, which may fracture and shatter the solidified intrusive body. The highly differentiated dike types could only have originated in some deep portion of an underlying plutonic body that had reached an advanced stage of magmatic differentiation. Appearing after these dikes, the mineralizing solutions may likewise be presumed to have originated at great depth. Certainly no source for these solutions can be found in near-by portions of the intrusive igneous body. The association of igneous intrusives and clustering ore deposits must be recognized as resulting from structural control. The emplacemerit and the subsequent solidification and cooling of the intrusive set in operation forces that are responsible for the favorable structural disturbances that control the mineralized district. The emplacement of the body of fluid magma weakens the crustal rocks to the extent that failure due to strains originally present in the rock body may occur. Faulting of any type and of any magnitude may be the result. Subsequently, owing to the change of state from fluid magma to crystalline granitic rock, volume decreases approximating 10 Per cent may Occur, with resultant shrinkage and collapse within the rock body. Following solidification, thermal contraction, induced by cooling of the rock body, causes a further volume reduction of 6 per cent. This thermal contraction, extending over a lengthy period of time, results in a succession of minor fault movements. These small fault movements, occurring progressively throughout the period of mineralization, are responsible for maintaining the permeability of the rock body, without which access of the mineralizing solutions and the formation of the ore deposits of the mineralized district would be impossible. Introduction A proper understanding of the causes that have localized our mineralized districts should be of considerable value to geologist and engineer alike. under current conditions the known ore reserves of productive mining camps are being rapidly depleted. Although ore of the future will be derived in part from deposits now known and from Ore bodies that are still to be discovered within the limits of productive mining districts, in part at least it must come from mineralized districts whose existence or importance yet remain to be recognized. The mining geologist is thus faced with two problems of paramount importance: (I) the location of new ore bodies within known mineralized areas and (2) the location of new mineralized districts within whose confines, previously unknown, valuable Ore deposits may occur. Any contribution to our knowledge concerning the causes for the localization of mineralized districts

Jan 1, 1949

By W. W. Vaughn, R. H. Barnett, E. E. Wilson

Soon after the search for uranium ores on the Colorado Plateau began in earnest, thousands of feet of drill core ranging from 1 1/8 to 2 1/8 in. diam became available for study. Although significant advances had been made in the technique of quantitative gamma-ray borehole logging, instrumentation was in the development stage, and complete reliance could not be placed on gamma-ray logs alone to interpret quantitatively the meaning of radioactivity in a drillhole. A method that would be faster than chemical analysis and still give reproducible and reliable results for various drill core sizes was desirable to provide additional information on the enormous footage of drill core being accumulated. A solid phosphor scintillation drill core scanner was designed and constructed. Basically the instrument was developed to measure radiation from a drill core which would not be clearly recorded by a gamma-ray logger using a Geiger tube as the sensitive element. Such data would be beneficial in constructing isorad maps to delineate ore-bearing zones. A calibration in the range 0.01 to 0.1 pct eU.,O, was provided; above 0.1 pct eU3O8 gamma-ray logs were available and were being used to calculate grade and tonnage of ore reserves. The core scanner, however, has been used to estimate equivalent uranium content of ore-grade materials containing as much as 2.2 pct eU3O8 with an accuracy of ± 10 pct, the sample being in the form of a BX drill core. Actually, an apparent calibration of eU3O8 vs counts per unit time is a straight line with a slope that is a function of the sensitive element and the geometry of the counting assembly. A true calibration that will show the expected departure from a straight line is due principally to the random nature of the pulse from a radiation source and the nonlinearity of the electron circuitry. Design and Construction: Three methods of detecting radioactivity were considered and applied in developing the core scanner now in use: 1) the Geiger tube, 2) liquid scintillation phosphors, and 3) solid scintillation phosphors. The desired sensitivity and long-term drift characteristics needed for this operation could be attained only by using solid scintillation phosphors. All three methods are discussed. Before scintillation counters were common, nine beta-gamma sensitive Geiger tubes 7/8 in. diam by 12 in. long were used, arranged to surround the drill core with tube axes parallel to the axis of the core. This arrangement of Geiger tubes was en- closed in a lead shield 1 in. thick, and provision was made to slide a 6-ft length of drill core manually into the counting chamber, one foot at a time. A count for each segment was taken with a scaler while the core remained stationary. The equivalent uranium content of the different sections of drill core could then be estimated with the aid of a calibration curve of counts per unit time vs percent equivalent uranium (eU). In rare cases the effects of the radioactivity concentrated in small areas within the core introduced errors in the readings made with the Geiger tube arrangement owing to the geometry of the measurement. The variability of counting rate due to a localized concentration of radioactivity in a spot in the wall of a drill core is illustrated in Fig. 1. This effect and the inherent low efficiency of the Geiger tube were considered major disadvantages of this counting arrangement. When liquid scintillation phosphors became available the core scanner in Fig. 2 was constructed to make a more accurate measurement of the equivalent uranium content of a sample. This instrument contains about 4 liters of liquid phosphor in a stainless steel coaxial cylinder 1 ft long, with inner and outer walls 0.060 in. and 0.125 in. thick, respectively. Four end-window type photomulti-plier tube with cathodes of 2 in. diam, immersed in the solution at right angles to the axis of the core, were used to observe light flashes in the phosphor. The liquid phosphor offered equal sensitivity to radiation originating at any point in the enclosure and represented geometrically the optimum in design. However, providing a semi-permanent leak-proof seal between the glass envelope of the phototube and the metal walls of the container proved to be a serious problem in constructing the equipment. The most effective seals were especially machined O-rings from sections of large tygon tubing. The tygon took a permanent set owing to cold flow characteristics and in most cases sealed completely. The light absorption characteristics of the liquid phosphor changed gradually with time, and after one month the counting rate had decreased to half the original value. The most sensitive liquid phosphor tested proved to be a solution containing 4 g of 2.5-diphenyloxazole and 0.01 g of 2-(1-naphthy1)-5-phenyloxazole per liter of toluene. With fresh solution in the chamber and with all photomultiplier tubes operating in parallel, the counting rate contributed by any one of the four photomultiplier tubes was about 85 pct of the counting rate from a single tube operated individually. From these observations it was concluded that owing to coincident loss and light attenuation within the liquid phosphor, the apparent sensitivity could not have been materially increased by additional phototubes. However, this approach to core

Jan 1, 1960

Effect of Activated Carbon on the Leaching of Cobalt-Rich Ferromanganese Crust in Sulfuric Acid

Sep 13, 2010

By U. C. Tainton

THE world-wide continuation of low prices for zinc in 1934 has militated against any striking changes in the position of the metal. The price of zinc in London at the end of the year, about £11 5/8 per long ton, or 2.5c per pound at the existing rate of exchange, is more than 25 per cent below the average price for last year. In these circumstances probably the most significant event of the year was the putting into operation of the new electrolytic plant of the Giesches company at Magdeburg, Germany. This plant is designed to have an initial capacity of 20,000 long tons per year, and it is planned to increase this to 40,000 tons annually. This development is significant not only as indicating a continued swing of zinc metallurgy towards electrolytic methods, but also because it will make Germany virtually independent of foreign sources of zinc. This will mean that the zinc tonnage normally exported to Germany from Belgium and Poland will. become available for other markets, and it is feared may lead to lower prices unless the production of Bel-

Jan 1, 1935

By Harry L. Washburn

Use of coal thermal dryers has steadily increased since 1928 when one of the predecessor companies of the present Consolidation Coal Cu. constructed a complete preparation plant with thermal dryers. Today there are about 25 additional preparation plants that, all together, use over 65 individual thermal dryers of almost every type. The thermal dryer is a heat generator and the unit may have a separate furnace or a firebox that is an integral part of the dryer. It is also a materials handling device that allows an intimate mixture of wet coal and hot gases with instrumentation for temperature control and. in some cases, the more difficult flow rate of hot gases. The materials handling portion of the dryer is subject to the normal wear and teal of any similar device plus effects of heat, water vapor, moisture: and, sometimes, acid. With present emphasis on air pollution. most fine coal dryers have wet scrubbers.

Jan 8, 1963

By Markus A. Reuter, Jacques J. Eksteen

The modelling of bath type furnaces tends to be either fundamental in nature or total empirical "black box models". While models of the first kind are robust, they tend to lack accuracy, in cases where they are to be used for process control, and may take an overly long in development time. On the other hand, black box models tend to lack robustness of prediction for all circumstances and tend to be limited to interpolate based on historical data. While this may very often provide short-term accuracy, the models may have problems with stability in the long term. Moreover, the model structure may not reflect any of the fundamental properties of the system and remains opaque to fundamental analysis. The aim of the model development is in obtaining a model that have robustness, high accuracy, a short development time and which is adaptive to a changing environment. The models are specifically developed for on-line decision support or control of furnaces. The modelling approach is evaluated for a chromite bath smelting furnace. The role of systems analysis, mass balance smoothing, thermodynamic analysis are integrated into one generic algorithm for bath type furnaces. Therefore, this paper argues that to understand complex metallurgical furnaces a hybrid approach is the only method to fully grasp the intricacies of metallurgy, to improve operations, economics as well as environmental performance.

Jan 1, 2003

By J. S. Kirkaldy, D. G. Fedak

The extra degree of freedonz introduced by a second independetzt concentration in a tenzary system gives rise to the possibility of unstable planar phase interfaces in semi-infinite diffision layer couples. Diffusion paths which pass continuously in and out of too-phase regions of the phase diagram but which are not coincident with tie-lines give rise to super saturated zones which may be either adjacent to or isolated from planar phase interfaces, with corresponding nonisolated or isolated precipitates. Nonisolated precipitates are equivalent to morphological development of the interface. Selected couples in the ternary systems Fe-Ni-Cr and Cu-Zn-Sn have been examined nzetallographically and ifz the latter case both isolated and uo~zisolated precipitates have been observed. The diffusion path in one of the couples showing interface morphological developtnent has been examitled using electron probe microanalysis. IGNORING the spurious effects of preferential grain boundary diffusion and anisotropic crystal growth7 it can be unequivocally stated that it is impossible for a binary isothermal diffusion couple constructed of two unsaturated phases to sustain a nonplanar phase interface. Consider for demonstrative purposes the schematic phase diagram of Fig. l(a). Given an initial flat phase interface, semi-infinite boundary conditions and the internal boundary condition fixed by the constitution diagram, xB = xB(T), the unique solution of the diffusion equation requires a persistent flat interface. No other solution is possible. If, however, we anticipate the involvement of surface tension, then the internal boundary condition must be written xB = xB (T,Y) where r is the radius of curvature of a hypothetical nonplanar interface. The introduction of a new parameter such as r can be equivalent to the release of an internal constraint, so that a stable nonplanar interface may be possible after all. Consider a perturbation to the interface as indicated in Fig. 1(b). According to the Ostwald-Freundlich equation: which is applicable to a system of this constitution, the solubility of A in the matrix ß ,xB (Y), at a point of curvature r is given by where Va is the molar volume of the a-phase, R is the gas constant, and a is the interfacial tension. Since the right hand side is positive, xB(r) >xB cm, as indicated in Figs. 1(a) and 1(c). Accordingly, the perturbation will carry the interface concentration in a direction which is opposite to that which would sustain local equilibrium. Such a perturbation is necessarily moderated and the system is returned to its initial condition. This result is general for all binary couples since we can regard an interfacial perturbation as an attempt to precipitate within un-

Jan 1, 1962