Search Documents

By Martin A. Elliott

The Bureau of Mines began its investigation of the use of Diesel engines underground to provide technical information necessary to assist this development in the United States. It was considered desirable to furnish such assistance because successful European developments/ in this. field had indicated that Diesel mine locomotives might be safer than electric trolley locomotives. The Bureau has recognized for some time the importance of eliminating the hazards associated with underground haulage systems using bare trolley wires. For example, each year 30 to 40 fatalities occur as a result of electrocution by contact with bare trolley wires. In 1943 and 1944, 101 men were killed and extensive property damage occurred as a result of mine fires started by falls of roof grounding the bare trolley wires.

Jan 1, 1948

Adsorption of Alkylammoniums in the Interlayer of Montmorillonite and its Effect on the Viscosity of Organo-Montmorillonite Gels

Sep 13, 2010

By AIME AIME

A PAPER recently presented before the Anthracite Section of the A. I. M. E. by S. J. Phil- lips, Mine Inspector, Fifth Anthracite District, Department of Mines of Pennsylvania, covering the water hazards in the anthracite coal mines of the Lackawanna River Valley, was especially timely because the conditions there are duplicated to a large extent in the Wyoming Valley, which is traversed by the Susquehanna River with its many large tributary streams. Also, in the southern anthracite field, where there are a number of large creeks, similar pumping problems and mine water hazards will in time be presented if mining is continued to its conclusion.

Jan 1, 1936

By A. G. Pentland

MODELS of mines may be classified under three headings: (a) sheet models, (b) solid models, and (c) skeleton models. Sheet Models are made of sheets of glass, celluloid, or a transparent plastic material. The sheets are mounted in a frame which holds them in a parallel position, either horizontally or vertically. Mine plans are traced on the horizontal sheets; sections on the vertical sheets. The model may be illuminated by electric lights which are separated from the sheets by an opalescent screen. It is viewed from above or from the side in such a way that the plans or sections are superimposed. Sheet models are very useful for the illustration of mines with narrow, steep-dipping veins, but they do not give a satisfactory representation of a large mine with a flat-dipping vein. Large sheets of glass are difficult to handle and to support in a frame.? It is difficult to see through a considerable number of them. Solid Models are made of plaster, concrete, wood, or other material usually in the form of slabs in which the mine workings are indicated by properly dimensioned cavities in the model. The slabs are coloured to show the veins, country rock, faults, etc. The model is divided along selected sections in order to give access to the interior by the temporary removal of parts. Solid models may be used to illustrate large orebodies of the Sullivan type, but they are cumbersome because parts must be removed to study details of structure. Skeleton Models are ones in which the underground cavities are represented by metal, wood, plaster, or wax proportionately shaped and held in place by a frame. They illustrate the work which has been done but do not show the position of the veins, dykes, faults, etc., in the unworked parts. It is necessary to project by eye between workings in order to determine the location of these features. The essential difference between the skeleton model and the solid model is that the skeleton model represents the mine workings by solid forms and does not show the unworked parts of the vein, whereas the solid model shows the vein as a solid and the mine workings as cavities in it. The skeleton model lends itself well to the representation of a large mine with large stopes.

Jan 1, 1944

A brief history of the significant haulage truck feature changes and the factors that influenced those changes during the 60's and 70's provide a basis for forecasting the changes that can be expected in the 1980's. A review of the impact factors and changing requirements that currently exist that will create changes. Define the critical requirements of a successful haulage truck design and discuss the availability of bigger engines and better electric drive componetry to provide deeper pit capability and improve reliability. The Unit Rig Trolley Assist System to provide improved productivity and diesel fuel savings and an economic analysis to evaluate the Trolley System is covered. The Unit Rig Automatic Truck System for a driverless truck is covered in concept and discussed from the point of view of the experience in a test in a New Mexico mine. INTRODUCTION A good basis for trying to forecast what is going to happen in the future is to go back a little bit in history, to see what the influencing elements were in different periods of time as a foundation for the forecast. INFLUENTIAL FACTORS IN THE 1960'S If you look at the truck development that occurred in the 1960's, there were some identifiable factors that give us insight. (See Fig. 1) Several things happened at the beginning of the 1960's. Mechanical drive haulage trucks were introduced that were

Jan 1, 1982

By R. V. Ramani, R. Bhaskar

"An airborne dust cloud is an ensemble of particles of varied size, density, shape and states of aggregation. An understanding and quantifying of the dispersion and deposition of the du.st generated in mines is essential to the development of measures for reducing worker exposure to dust.In coal mining, the major portion of the dust is generated during the cutting of coal using a shearer or a continuous miner. The major phenomenon affecting ambient concentration is the deposition of dust. Panicle deposition may take place due to the effect of gravitational, inertial, electrostatic, and thermal forces, and mechanisms such as Brownian and eddy diffusion and inenial impaction. The three major mechanisms of deposition in turbulent flow in mines are diffusion (Brownian and eddy), sedimentation and inertial impaction. The mechanisms determining panicle deposition are size dependent.From a review of the literature, there appears to be a knowledge gap in the understanding of the deposition phenomena in mine airways. In order to obtain a better understanding of the deposition of dust for various particle sizes, and to develop a set of data for evaluating predictive mathematical models/or dust flow in mines, a series of dust-flow experiments was performed under controlled conditions in mine airways. It appears that the deposition data generally follow the theoretical behavior of dust based on the combined effect of diffusional and gravitational deposition. Jn this paper, the findings of the study on the deposition of dust in mine airways and its dependence on size, velocity and concentration are discussed. A set of deposition equations that could be used to determine the approximate deposition at various points in a mine airway are presented.IntroductionThe major factor affecting ambient dust concentration in mine airways is the deposition of dust. Particle deposition may take place due to the effect of gravitational, inenial, electrostatic, and thermal forces, and mechanisms such as Brownian diffusion, eddy diffusion and inertial impaction. The major mechanisms of deposition in turbulent flow in mines are diffusion (Brownian and eddy), sedimentation and inertial impaction. Inertial impaction is significant only during changes in direction, but the change in direction of flow with resultant powerful eddies may cause increased re-entrainment of the particles, thus having a compensating effect. While the literature in aerosol sciences contain several references on deposition, most studies were done in small diameter tubes for diffusional deposition (Liu and Agarwal, 1974). The deposition data from small diameter, short tube experiments may not be applicable to studying deposition in mine airways that have large areas and extend several hundred meters. Further, the change in concentration along the length of a mine airway may significantly affect the deposition an aspect that may not be easily determined in short tubes in laboratory experiments."

Mar 1, 1992

By A. Kenneth Schellinger

DURING the comminution of a brittle material in the presence of dry air, no known phase change or chemical reaction takes place. The energy changes associated with the comminution are those of the transformation of kinetic energy into heat energy and the energy absorption represented by the actual rupture of molecular and/or ionic bonds. The random nature of the actual grinding process in a tumbling-mill often precludes the effective application of a rupture force on each individual particle of brittle mineral present. The result must be a great deal of useless vibration on an atomic scale in both the brittle mineral and the grinding medium below the elastic limit, which vibration is eventually manifested as heat energy in the mill. The actual rupture of molecular, or ionic, bonds creates new surface on the brittle minerals; each square centimeter of this new surface then must possess a number of potential bonds, each of which could reform theoretically with the release of energy. The sum total of this potential energy of bonding per unit of new surface, minus bond satiation effects of the enclosing gas or liquid, must be the surface energy of the mineral. If the comminution of the brittle mineral were carried out within the chamber of a calorimeter, the energy released as heat could be determined rather accurately. Moreover, the total kinetic energy input to the comminuting mass (mineral and medium) conceivably could be derived by a suitable torquemeter and revolution counter if the whole calorimeter were revolved. The difference between these two energy figures should then represent the net energy (gross energy input-heat energy output) used in creating

Jan 6, 1951

By John Birkinbine

In a former paper* attention was directed to the various forms of pumping machines employed for permanent work in mining and metallurgical processes. The following is simply a collection of memoranda of work done of a temporary character, and is presented by way of comparison with other work of similar nature. In close proximity to the charcoal fnrnace at Pine Grove, Cumberland County, Pa., is a large deposit of superior hematite iron ore, which has been worked for a number of years, and from which many thousand tons of ore have been taken by open pit workings. In July, 1874, the furnace was blown out and operations at the bank suspended, the machinery for draining being removed except a plunger pump, 18 inches in diameter and 66 inches stroke, operated by a steam-engine by means of rods. The pit was allowed to fill with water, and no steps towards its reclamation were taken until November, 1877. At that time the pit was a pond of water at the base of the mountain, having an area of about four acres and a depth of seventy feet. As the pumps, rods, etc., had been submerged for over three years, and partially buried by the mud washed down from the banks, and as it was determined to change the location of the pump for future operations and drive it by water-power, a temporary pumping apparatus was determined upon for reclaiming the pit and keeping it drained until the permanent arrangements could be completed. By opening an old adit about 10 feet of the water was removed, and the area decreased to three acres. The inflow of springs was found to be 250 gallons per minute, and the amount of water contained in the pit was computed to be 45,000,000 gallons. As the inflow would undoubtedly increase while the water sank in the pit, provision was made for removing at least 60,000,000 gallons, at the rate of 1,500,000 to 2,000,000 gallons per day. The company determined to employ a Heald and Cisco centrifugal pump driven by an oscillatinig engine by means of a belt. Steam was supplied by four plain cylinder boilers, each 36 inches diameter

Jan 1, 1879

By Albert W. Deurbrouck

Twelve samples from six Barbour County coal beds were analyzed for this report. The samples collected were generally high sulfur content coals, frequently exceeding 3 percent in the raw-coal sample. Many of them could not be upgraded to acceptable metallurgical standards even by rigorous preparation procedures. The production of coal in the county in 1963 amounted to almost 3 million tons of which 44 percent was mechanically cleaned.

Jan 1, 1965

By Minerals and Materials Analysis Section

During 1996, US mines produced 319 t (10.26 million or) of gold metal valued at $4 billion. At yearend, mine reserves were estimated to be 4.7 kt (151 million oz) of gold metal. Almost all of the production was from western states. Nevada accounted for about 68% of national production. Information for this article was obtained through annual reports of mining companies, US Geological Survey (USGS) databases and other public sources. Table 1 shows production and reserves by mine. It divides the mines into two categories. These are producing mines whose primary product is gold, and producing mines for which gold is a byproduct or coproduct. The mines listed in Table 1 accounted for more than 98% of US gold production during 1996. Except the Daisy Mine, the table does not include mines that produced less than 31 kg/a (1,000 oz/year). The Daisy Mine started production in December of 1996. Nor does it contain mines whose byproduct concentrate is

Jan 1, 1997

By S. S. Klima, A. L. Mazzella, J. S. Driscoll, T. W. Beck

Previous testing was performed by researchers at the National Institute for Occupational Safety and Health (NIOSH) to improve longwall dust control using underside shield sprays with a longwall directional spray system. This testing provided encouraging results toward respirable dust exposure reductions for longwall personnel, achieving as high as 99% dust reduction at some sampling locations along the longwall personnel walkway. Additional laboratory testing was conducted to test these underside shield sprays in conjunction with a shearer-clearer spray system located on the longwall shearer body. The purpose of this testing was to determine if the underside shield sprays interacted positively or negatively with the shearerclearer sprays. Results from this testing indicate that while the shearerclearer system influences where the respirable dust particles are directed, underside shield sprays can still lower respirable dust exposure for longwall personnel.

Mar 2, 2022

By C. -S. Xie, J. -H. Kong

The microstructure and mechanical properties of X80 hot-rolled thick steel strips with a thickness of 17.5mm produced in Wuhan Iron & Steel Company (WISCO) are introduced in the paper. The steel strips as fabricated through proper thermomechanical processing (TMP)/ on-line accelerated cooling (OLAC) processing have shown high strength and toughness, low brittle transition temperature, good weldability, and high Shear Area (SA) percentage in Drop Weight Tear Test (DWTT). The microstructure of the steel strips is characterized with mainly acicular ferrite, and fine dispersed Martensitc-Austenite (M-A) phases. It is determined that the mechanical properties are improved due to the presence of the fine M-A phases and precipitates, which could be formed by reducing the finish rolling and coiling temperatures.

Jan 1, 2005

By E. J. Schmitz

This trip, beginning at Springfield, August 12, 1897, and ending at the same place fourteen days later, extended south and southeast through Christian, Ozark and Taney counties,

Jan 1, 1899

By R. Minto, W. G. Davenport

The slag removed from the reverberatory furnaces of copper smelters contains significant copper values. A serious financial loss is involved, as further recovery operations are not normally carried out. This paper describes the factors affecting physical transport of matte into slag by gas bubbles, and the subsequent entrapment and flotation of matte drops. Three distinct patterns of transport behaviour have been identified from studies of a number of liquid/liquid systems, including liquid metal and liquid matte systems. A theoretical approach is proposed to explain these behaviour patterns, and to predict transport and entrapment behaviour in matte/slag systems. The concepts of "Film Coefficient" (ø) and "Flotation Coefficient" (?) are introduced. The effects of smelting process variables on the physical loss of copper matte in slag are also discussed.

Jan 1, 1972

By Michael Schaffer

The paper point out how APC (Advanced Process Control) can be implemented in a stepwise fashion, where each step demonstrates a return and builds towards the overall achievable benefit. Initial efforts focus upon areas that demonstrate the highest potential for quick payback. By attacking small, contained scope, the APC solution is manageable from both a commercial and technical perspective. While this approach results in a slower implementation with correspondingly delayed payback, it provides tangible benefit and addressees the fiscal reality of many operations.

Sep 12, 2005

In Australia 'there are hidden deposits of gold, copper, tin, lead and zinc which can be found by drilling at reasonable expense in view of the imp9rtance of the objectives. Exploration of the prospects in mind would mean about a million feet of drilling. The purpose of this paper is to outline, in a technical way, some of the geological thinking that has been given to this matter. To do this, it is necessary to unify the wider ranging thoughts into some sort of coherent perspective and also into some sort of logical sequence. This will be done by treating first the geological subject material which is in fact, at the foundation of the exploratory scheme. With this base, the argument will be continued through a sequence of prospect thinking and brought to a conclusion in regard to the practical employment of geology in the drilling planning. In this knitting together of ideas, the discussion will be given substance by welding into the argument the reasoning that has been applied to the Cobar prospect. The New Occidental Gold-Mines are operating three mines at Cobar, and the writer is indebted to the Company for allowing the reference to be made. It is intended, as opportunity permits, to furnish further examples in later publications.FOUNDATION OF EXPLORATIONThe deposits under consideration are derived from igneous rocks, chiefly granite or porphyry. In and following the emplacement of the intrusives, the rocks have been...

Jan 1, 1946

By Thimons E. D, Derick R. L

In early June, 1986, a fire of unknown origin erupted in one of several main entries of a coal mine located in southwestern Colorado. The fire was aggressively fought with high-expansion foam. As a result of several strategic decisions, the fire appeared to be held in-check. Unfortunately, sufficient quantities of foam were unavailable and as soon as the foam was depleted, control of the fire was lost. To prevent further damage and the possibility of an explosion, all entries to the mine were sealed.

Jan 1, 1988

By Li Huimin

In this paper the step of determining the property index and the program of mixture ratio design of stabilizing agent in deep foundation construction are presented. According to the principle of computer simulation, the model and the method of computer simulation for optimum mix design are set up. Also, the precision of simulation results has been estimated and verified experimentally.

Jan 1, 1991

By W. C. Meyer

A physical model of flotation, derived from viewing froth as a kinetic species since it constitutes the carrier of ore particles, not only agrees with and is simulated by engineering math models, but is statistically verified by actual laboratory flotation data. The model couples the mechanical removal of froth using paddles with the more rapid chemical interactions taking place in the bath. It clearly shows that the kinetics of mass removal is dictated by flotation cell dimensions, paddle speed, and, more importantly, froth characteristics. Some conclusions and predictions of the model are presented.

Jan 1, 1982

By U. Meyer, A. Alonso, P. Banios

The sampling of cathodes has changed with the introduction of the ISA-process in copper refineries. A Jernkontoret joint working group of refineries and rod plants from both primary and recycled copper plants has been investigating whether the actual sampling of cathodes is representative for this type of cathodes. As a first stage, samples were sent to the members of the working group with the objective to find an easy basis for a comparison of the results of the next stages. All samples show the same tendency for nearly all elements. In some cases, there may exist differences in calibration and for some elements the detection limits are too high, especially when Optical Spectrometry is used. In the second stage, discs were compared with melted samples to answer the question whether the punching of discs is sufficient for the quality control of the cathode. The analyses of the discs represent fairly well the cathode quality. There are differences between cathodes from different crops. Three punches are sufficient to determine the cathode quality. Finally, samples from various lots of cathodes were compared with samples from the rod produced from these cathodes. The impurity content of the rod corresponds to the impurity content of the cathode.

Jan 1, 2000