Search Documents

Japanese pig iron production in 1973 registered about 90 million tons. As clearly seen from the productivity (2.04 t/m3/D), and fuel ratio (494 kg/t-pig), the Japanese steel industry has maintained quite high levels of efficiency in blast-furnace (BF) operations. Among the many factors which have contributed toward these high levels of efficiency, the use of high quality coke is very important. The Japanese steel industry imports about 85% of its metallurgical coals from various countries of the world, including Australia. The effective use of these metallurgical coals of various origins in accordance with their re- spective properties is most essential for maintaining coke quality. This paper describes coking properties of various metallurgical coals and blending techniques based on these coking properties, in relation to the specifications of coke quality required for efficient BF operations. This paper also describes briefly new technology for expanding the scope of the use of coking coals.

Jan 1, 1975

By Daryl R. Tweeton

Bureau of Mines research in in situ uranium leaching includes injection well construction and environmental aspects. Clogging of injection wells is a common problem, and is affected by construction techniques. Part of the clogging can be caused by a low-permeability skin left on the borehole wall if the drilling fluids are not thoroughly flushed out. Certain polymer drilling fluids are less prone to cause clogging than bentonite muds, since a lower solids content can be used. The environmental research primarily involves two contracts. The first describes the environmental impact of in situ leaching and the effect of environmental legislation on leaching; the second describes the cost effectiveness of various methods of restoring ground water quality.

Jan 1, 1978

By Arumba J

In the Mount Victor area of the Eastern Highlands Province, re- connaissance geological mapping and new micropalaeontological data have revealed the existence of at least three small thrust- bound windows exposing late Middle to Late Cretaceous (Late Aptian-Early Albian and Late Santonian-Maastrichtian) sedimen- tary rocks and pillow lavas, Latest Paleocene- Earliest Eocene pillow lavas, and Latest Paleocene-Earliest Eocene bathyal micrites. Late Middle Eocene to Late Eocene inner neritic bioclastic micrite units also occurs in thrust contact with Middle Miocene Yaveufa Formation volcanolithic conglomerates. The Cretaceous and Early Tertiary units appear to be thrust-bound and are best exposed in a window just south of Mount Victor, and in two smaller windows to the east. The inner neritic Eocene limestone occurs in a thrust-bound sliver within the Yaveufa For- mation near Obura. The windows occur within extensive out- crop of Early Miocene Omaura Formation and the Yaveufa For- mation. Thin-bedded grey mudstone, siltstone and sandstone, typical of much of the Chim Formation form only a small part of the exposure of Cretaceous rocks. Thick-bedded volcanolithic conglomerate, spilitic pillow basalts, and welded basic tuffs domi- nate the Cretaceous section. The stratigraphy and structure of the Mount Victor area is similar to the Menyamya area, the Aure Scarp, and perhaps the Tapini area. This study has raised the possibility of widespread thrust- ing in the Kainantu area, and suggests that the boundary between the Omaura and Yaveufa Formations is thrusted, at least locally.

Jan 1, 1997

By AIME AIME

WITH the recent increase in the price of gold, its economic recovery at depths formerly considered impractical has become a present possibility. Two important difficulties must be met: pressure bursts of the rock, and the reduced efficiency of human labor subjected to the higher temperatures and the increased humidity at the greater depths. In the following abstract of a paper by J. H. Dobson, presented before the South African Institution of Engineers on

Jan 1, 1935

By J. E. Burke, Y. G. Shiau

SEVERAL attempts have been made to account for the fact that grains in a fully recrystallized metal will coarsen on annealing Two fundamentally different hypotheses have been advanced; with several variations of each. One school considers that the cause of grain growth is the surface energy of the grain boundary The theory of Jeffries1 that grain size and grain size contrast control growth is an example The second school considers the primary cause to be a difference in the lattice energy on either side of the grain boundary The more perfect grains are considered to grow at the expense of their less perfect neighbors, with a decrease in free energy, and a consequent increase in the stability of the system. Burgers2 presents the case for the strain or lattice imperfection theory of grain growth quite completely The latter theory is attractive, since there is no doubt that differences in lattice energy or lattice perfection can cause grain boundary migration A recrystallization nucleus grows for this reason as was beautifully demonstrated by van Arkel and Ploos van Amstel3 Although it is generally stated that grain growth does not precede recrystallization, several workers4,5 have shown that small strains may induce a single crystal in an aggregate to grow, or at least may cause some' grain boundary migration The origin and nature of the imperfections that are considered to be responsible for normal grain growth have never been clearly described, but it is generally agreed that they are a consequence of the difficulty of atomic reorientation in the solid state, and that they do not seriously differ from the type of imperfection that-can be introduced by mechanical deformation An object of the present work was to determine whether the introduction of mechanical deformation would cause grain growth in a specimen which would not otherwise show it under the conditions used It was also planned to determine the effect of such deformation the rate of growth in a specimen which would show - growth in the unstrained condition Recently Maddigan and Blank6 have indicated that slightly strained specimens of alpha brass can undergo considerable growth prior to recrystallization if annealed at low temperatures French7 has reported that at deformations less than 17 pct it is very difficult to detect the beginning of recrystallization in the same material. It was therefore planned to broaden this work to include a complete study of the microscopic behavior of alpha brass under conditions of temperature, time, grain size and deformation such that recrystallization would not occur or would occur to only a small extent EXPERIMENTAL PROCEDURE The brass was prepared by melting cathode copper and commercially pure zinc

Jan 1, 1947

By Sergio Segovia Parra, Victor Hernan Sheen Uriol

This contribution of the concept of mass blasting both closing and production allows breaking paradigms, to limit the number of tons to thunder. The areas of geotechnical different mining large mining companies worldwide and especially from the National Copper Corporation (CODELCO, Chile) has been declining volumes closing blasting and production, with the misconception to protect the end walls of the pit, before any geotechnical risks caused by various types of faults; especially the circular faults. A blasting of small tonnage can do more damage to a wall when it is not properly sequenced, leading to the coupling of the wave train and therefore the exponential damage in/s (peak particle velocity, PPV) on the wall of the Tagus. Blasting closing mass production and contribute technically and operationally in the dynamics of the following operations: loading, hauling, crushing, processing and preparation of the final product; eliminating delays to return to thunder small volumes where one must stop all mine equipment, incurring high costs and especially losing valuable time in the continuity of the following unit activities.

Jan 1, 2015

By Peter C. Jones, Wanda M. Carter, David H. Watkinson

"Abstract - Pyrrhotite, chalcopyrite, and pentlandite are the dominant sulfide minerals in the 740 zone of the Kelly Lake orebody (Inco Ltd.), Copper Cliff Offset, Sudbury. Petrographic and quantitative electron microprobe analyses of minerals, from sulfide assemblages and host quartz diorite, of the 740 deposit have revealed three processes that have affected sulfide mineralization and associated sulfarsenide and platinum-group-mineral (PGM) distribution: magmatic, hydrothermal, and tectonic. Accessory, zoned cobaltite, and gersdorffite occur in sulfides as a result of these three processes, and PGM occur dominantly in hydrothermally remobilized and deformed ores. Where PGM are present in sulfarsenides they provided nuclei for sulfarsenide growth. Solitary PGM are orders of magnitude larger than those PGM found within sulfarsenide minerals. Five varieties of PGM occur, michenerite and sperrylite being the most common, with lesser froodite, hollingworthite, and ruarsite.The effect of a deformation is a localized fabric in the ore, revealed by pyrrhotite and chalcopyrite bands; pentlandite porphyroblasts also partially define the foliation. The deformed ore is also characterized by alteration of the adjacent quartz diorite, which produced an alteration assemblage including almandine garnet, Fe-rich biotite, and chlorite."

Jan 1, 2001

By M. Sanchez

In the last decades, the Chilean copper mining and metallurgical industry have had to modify their technological processes to meet the environmental regulations implemented by the Chilean government, and also to support the pressure of the public opinion. Thus, air quality standards for sulfur dioxide and particulate matter (primary and secondary), plans for reducing emission of arsenic by the Chilean copper smelters, effluents discharge limits, among others regulations were applied by the environmental agency. Additionally, agreements on cleaner production were carried out by mining sector and government. Now, a draft law on mine closure, and another on environmental mining wastes (abandoned mines) are being discussed by the authorities and the mining sector. In the context, production and environmental impacts in different ways to produce copper in the Chilean mining industry are reviewed and regulatory tendencies as well as abatement technologies today used are exposed and discussed in this presentation. Pyro, hydro and electrometallurgical processes employed and their current effluent and contaminants are presented showing various alternatives of treatment in the copper industry. An update of regulations established in Chile vis a vis copper production, with an especial attention to mine closure are also presented.

Jan 1, 2007

By G. E. McElroy

When mechanical ventilation is to supersede the natural ventilation of a mine it is desirable to determine what resistance the mine as a whole offers to the flow of air in order to specify properly the limiting duties of a ventilating fan. The relation of pressure to volume of flow for the mine as a whole may be calculated from experimental data, or it may be determined directly by measurements of volume of flow and the natural draft pressures causing flow; but in both methods the determinations are affected by many variables. With the intention of making a practical application of both methods, a small metal mine in process of development at Butte, Mont., was selected by the writers as the object of experiments planned to compare the mine resistances determined by measurements of natural draft and volume of flow with those calculated from experimental data. Four sets of teats were made with natural draft in October, 1925, December, 1925, April, .1926, and September to December, 1926; the last set consisted of a series of weekly observations. DESCRIPTION OF MINE The mine selected for the experiments was a typical vertical shaft metal mine in the development stage. No stoping had been done, and ventilation was confined to shafts, crosscuts, drifts, and raises. Figure 1 is a dia¬grammatic sketch of the main openings. All were timbered with full sets on approximately 5-foot centers. The shaft compartments were 4 by 4.5 feet, and one in each shaft was partly blocked by staggered manway landings. A pump column in the upcast shaft was discharging about 280 gallons a minute of water at 70° F. from the 1,000-foot level. The drifts were slightly sinuous, but the crosscuts were exceptionally straight and uniform in area; both drifts and crosscuts were about 5 by 7 feet in cross section. The raises were composed of vertical sections joined by frequent 450 offsets; each had three 4.5 by 4.5-foot compartments, of which two were plank-lined ore chutes and one was partly

Jan 1, 1928

By D. W. Partridge, W. Lamb, A. E. Lamb, S. Bird

Due to the constant need to improve SAG mill performance and efficiency, extensive research into all aspects of SAG mill optimization has been performed. This paper will review the current evolution of SAG mill shell liner design and their performance at the Copperton Concentrator. The effect of these liner design changes will be discussed with respect to: • Liner configurations • Mill operating performance, i.e., throughput, power draw, mill control • Mill mechanical performance, i.e., liner wear profiles, liner life, liner breakage, liner hardness • Foundry manufacturing considerations • Economic evaluation of throughput versus liner life This paper will discuss the results of Kennecott Utah Copper’s (KUC) and ME International’s (MEI) test work, providing an insight into the past, present and potential future opportunities of SAG mill liner design.

Jan 1, 2002

By David A. Lee

It was estimated in Chemical Week1 that the uranium fuel requirements for the U.S. Electric Utility Industry by the mid 1980's would be about four times that-of what it is today. This corresponds to approximately 45,000 tons per year of 'yellow cake' - of which a good portion is represented by ammonium diuranate - vs. the 11,700 ton total estimated for 1975. Perhaps just as significant is the 40-fold increase in thirty years projected for the entire world since 1970. Thus by the year 2000. 'yellow cake' production could be in the order of [3]50.000 short tons annually.2 'Yellow cake', so named because of its inherently bright yellow color, is a finely divided precipitate that can be formed after the leaching step when refining uranium ores. Feed solids enhancement then occurs to at least 50% by weight using filters or centrifuges This is followed normally by drying and then calcining with the conversion of ammonium diuranate to triuranium octoxide represented by the following equation: [9 (NH4)2 U2 07 heat 14 NH3 7 + 15 H2O7 + 2N2/ + 6 U308 4] Theoretically, assuming 100% conversion every 100 kgs. or 100 lbs. of ammonium diuranate will result in 90 kgs. or 90 lbs. of triuranium octoxide.

Jan 1, 1976

By Edwin A. Harre, John J. Mortvedt

Plants obtain nutrients from both air and soil. They absorb carbon dioxide mainly from the air, although some carbon dioxide may be dissolved in soil water which is absorbed by plant roots. Carbon dioxide, a gaseous form of carbon and oxygen, supplies the carbon which usually makes up 50% or more of plant structure. Growing plants use water more than any other biological substance. Plant nutrients dissolve in soil water and enter the plant via root absorption. Water is then given off into the air as the plant breathes or transpires. Water also supplies hydrogen and oxygen to plants. Plant roots absorb nutrient cations or anions by contact exchange with soil clay particles. Inorganic or mineral nutrients essential to plants are supplied through the soil. Inorganic or mineral composition of plants usually is less than 5% of their weight. In most crop-growing areas, much of this nutrition is inadequately supplied from soil reserves and must be provided by fertilizers. The role of the fertilizer industry is to provide economical, efficient, good quality fertilizers to improve or maintain soil productivity for optimum crop production. The essential plant nutrients other than carbon, hydrogen, and oxygen which often must be added to soils or plants are categorized as primary nutrients (nitrogen, phosphorus, and potassium), secondary nutrients (calcium, magnesium, and sulfur), and micronutrients (boron, chlorine, copper iron, manganese, molybdenum, and zinc). These classifications are based on quantity of nutrients utilized by plants and do not imply their function or degree of necessity. One point of major significance to the fertilizer industry is that not all fertilizer minerals contain the plant nutrients in a chemical form available to the plant. A product which may be considered a fertilizer mineral may require substantial processing or treatment before it becomes useful as a nutrient source or fertilizer.

Jan 1, 1994

By Takashi Nakamura, Kenji Oosumi, Kazuhisa Fujisawa, Takayuki Kogishi

"Recycling of used aluminum beverage cans(UBCs) is one of the important issues for aluminum manufacturer presently. The direct re-melting of UBCs shows two problems. One is a reduction in molten aluminum recovery and the other is a contamination of other metals such as Ti and Fe from paints. Both problems are caused by paints coated on the surfaces of aluminum cans. Removal technique of the paints, therefore, has been required. Although roasting and shot blast techniques have been developed, both were not successful in removing the paints effectively. A swell-peeling method has been applied to remove them using a methylene chloride solution with acids and it works very well. Small laboratory scale tests have been carried out to develop the commercial process and clarify the mechanism of the swell-peeling method in the present study.When the surface area of UBC is more than 10 cm2, peeling time is independent of the surface area, about 60 seconds, because swelling phenomenon is controlled by the penetration of the liquid through the fine pits on the surface of the paint. This is good for a commercial process. Peeling takes place when the swelling force generated by methylene chloride exceeds the adhesion force between the film and the surface of aluminum, that is weakened by the coexisting acid, especially halogenated acetic acid."

Jan 1, 2000

By K. Ronald Chapman, Claus Ludwig, Doug Jenevein

"In the spring of 2005 Schnabel Foundation Company completed a $15.2 million Design/Build subcontract to underpin 11 structures, and provide 202,800 square feet of earth retention for the Reno Transportation Rail Access Corridor (ReTRAC) project in Reno, Nevada. Schnabel’s work was part of a Design/Build contract to depress a railroad alignment through downtown Reno. The depressed section was 2.2 miles long, 54 ft wide, and up to 35 ft deep (3.5 km long, 16.5m wide and up to 10.7m deep). The trench structure was required to be watertight. SUBCONTRACT WORK OVERVIEWEleven buildings along the track alignment required underpinning. Three types of underpinning were used, designated Type 1, Type 2 and Type 3.At four buildings the trench retaining walls were to be located directly under the exterior footings. This alignment eliminated traditional underpinning and cut-off wall techniques that could normally be used to support structures. Type 1 underpinning was used at these buildings. This underpinning system consisted of a combination of permeation grouting, hand-dug piers, and permanent tiebacks. This underpinning system became the new watertight trench walls.Five buildings were located a few feet behind the trench walls, and their exterior walls were supported by continuous footings. Type 2 micropile/pile cap underpinning (patent pending) was used to support these buildings.The remaining two buildings were also located a few feet behind the trench walls, but they had column footings along the exterior walls. At these structures traditional micropile underpinning was provided through the existing footings. This is described as Type 3 underpinning.Temporary earth retention was required on both sides of the trench along most of the alignment. This shoring supported frontage roads, private property and surcharge from the temporary railroad shoofly running parallel to one side of the trench.SUBSURFACE CONDITIONSThe soil along the trench alignment consisted of river outwash deposits. The top 2 to 18 feet (0.6m to 5.5m) generally consisted of flood plain silt and sand deposits, or fine-grained fills. These fine-grained soils are underlain by the Tahoe Outwash Formation which consists of interbedded layers of sand; sand and gravel; and sand, gravel, cobbles and boulders. Some of these layers encountered during construction consisted of 30 to 50 percent cobbles and boulders, with some boulders up to eight feet in diameter.A major challenge to the design and construction of the trench structures and the underpinning was the ground water table which was 10 feet (3m) above subgrade in the deepest portions of the trench. Based on specification restrictions, temporary and permanent dewatering was not feasible. As a result, the selected design and construction methods had to consider three water conditions: the anticipated groundwater level during construction (CGW), the groundwater level for permanent design (DGW), and an additional special design condition with water at street grade."

Jan 1, 2006

The design of solvent extraction plants has been generally based on the assumption of steady operating conditions in both the settler and the mixer units. However, recent experience in both large and small plants has shown this not to be the case. Mixer transients include start up aqueous locking and partial phase separation in secondary mixers, which both lead to reduced plant capacity or overflow of upstream mixers. Analysis of the hydraulic pressure profiles has generated new design methods to eliminate the effects of the partial or complete phase separation. Changes to the method of specification and selection of primary and secondary mixers have been made to eliminate the onset of partial separation during operation. The observation of settler operation has shown that it is also a dynamic process, even under "steady-state" conditions. Four transient phenomena have been identified that lead to internal circulating flows, poor disengagement of fine secondary haze and erratic and high entrainment levels in the discharges. A, first approximation analysis has shown that there are significant pressure differentials within settlers, and these change along the length and with the phase separation rates. A technique to control the effects of these transients was developed that allows plant performance to be improved beyond "standard" expectations. The design and selection of the settler internals is described. Key words: Solvent extraction, Mixer-settlers, Phase separation, Entrainment, Mixer transients

Jan 1, 2003

By L.L. Wyman

The exact nature of the changes that take place in the iron-nickel alloys, giving rise to the interesting and useful expansion alloys in the Invar range, has yet to be fully understood. Similarly, the ternary iron-nickel-cobalt alloys, which also possess such commercially useful expansion characteristics,1,2 are concerned with transformations that appear to be identical with those found in the parent iron-nickel alloys. The investigations on iron-nickel alloys in the range 26 to 29 per cent Ni have been reported by several authors3-9 wherein it is shown that there are factors other than temperature, such as stress and grain size, which play an important part in determining the temperature at which the low-temperature transformation takes place. It will be shown in this paper that the ternary iron-nickcl-cobalt alloys having nickel contents comparable to the alloys mentioned above behave in a parallel manner. The alloys in the range of 26 to 31 per cent Ni and 16 to 21 per cent Co have a coefficient of expansion of about 4.0 X 10-6 per degree Centigrade, and the alloys in this range of composition find considerable application in making glass-to-metal seals, because these expansion properties so well match commercial glasses. The behavior of these alloys is not a simple matter, for it has been observed in alloys of 28.5 per cent Ni and 18.5 Co that severe working ran cause the appearance of a second phase having a needlelike structure similar to the martensite structure in carhon steels. Fig. 1 shows the change brought about in an alloy of this composition when a strip of this material was cut with tin shears. This second phase has been identified as the body-centered cubic alpha phase, and it is the purpose of this paper to describe the results of some of the preliminary investigations in the study of the changes involved in these alloys. Materials The past work on these alloys has concerned itself primarily with materials made by the usual casting procedure and involving the use

Jan 1, 1939

By L. L. Wyman

The exact nature of the changes that take place in the iron-nickel alloys, giving rise to the interesting and useful expansion alloys in the Invar range, has yet to be fully understood. Similarly, the ternary iron-nickel-cobalt alloys, which also possess such commercially useful expansion characteristics,1,2 are concerned with transformations that appear to be identical with those found in the parent iron-nickel alloys. The investigations on iron-nickel alloys in the range 26 to 29 per cent Ni have been reported by several authors3-9 wherein it is shown that there are factors other than temperature, such as stress and grain size, which play an important part in determining the temperature at which the low-temperature transformation takes place. It will be shown in this paper that the ternary iron-nickcl-cobalt alloys having nickel contents comparable to the alloys mentioned above behave in a parallel manner. The alloys in the range of 26 to 31 per cent Ni and 16 to 21 per cent Co have a coefficient of expansion of about 4.0 X 10-6 per degree Centigrade, and the alloys in this range of composition find considerable application in making glass-to-metal seals, because these expansion properties so well match commercial glasses. The behavior of these alloys is not a simple matter, for it has been observed in alloys of 28.5 per cent Ni and 18.5 Co that severe working ran cause the appearance of a second phase having a needlelike structure similar to the martensite structure in carhon steels. Fig. 1 shows the change brought about in an alloy of this composition when a strip of this material was cut with tin shears. This second phase has been identified as the body-centered cubic alpha phase, and it is the purpose of this paper to describe the results of some of the preliminary investigations in the study of the changes involved in these alloys. Materials The past work on these alloys has concerned itself primarily with materials made by the usual casting procedure and involving the use

Jan 1, 1939

By S. W. Poole, J. A. Rosa

THE object of this investigation was to determine the distribution of chemical elements within a large, killed alloy-steel ingot, by sulphur printing and quantitative chemical analysis. With regard to segregation in steel ingots, the factors of melting practice, pouring temperatures, mold design, etc., and the mechanics of solidification and its attendant functions, have been the subject of intensive study over a period of years by many investigators. Notable among these is the Sub-Committee of the No. 5 Committee of the British Iron and Steel Institute. For an exposition 0f the many problems awaiting the researcher on the heterogeneity of steel ingots, the methods of attacking these problems, together with some of the answers, the reader is referred to the nine reports and numerous papers of that committee and its membership. STEELMAKING DATA Melt.-The heat was made in a 70-ton direct arc-type basic electric furnace. Furnace charge consisted of nickel-chromium-molybdenum steel, most of it in the form of heavy mill scrap. All of the scrap was charged cold. The standard double-slag method was employed, the heat being finished under a strong carbide slag. Aluminum was used as the deoxidizing agent. Tapping temperature, as observed with an optical pyrometer, was 3000°F. Detail of Mold and Ingot Size.-Details of the ingot mold and the ingot itself are given in Fig. I. Teeming.-Teeming temperature of the subject ingot as observed with an optical pyrometer was 2830°F. The ingot was top-poured directly through a 1 ½ in. nozzle and required 7 min., 44 sec. to fill up to the hot top. An additional 2 min., 30 sec. were required to fill the hot top. The ingot was stripped hot and charged with the remainder of the heat into an annealing furnace. There it was given the standard annealing cycle used for these ingots. Subsequent heat-treatments are described elsewhere in this paper. SECTIONING AND PREPARATION FOR SULPHUR PRINTING Because of previous favorable experience in sectioning ingots up to 21 ½ in. square with an oxyacetylene torch, it was decided to use this method to section the subject ingot. The ingot was preheated to 900°F. for 12 hr. It was then placed on a steel bed in a horizontal position so that the longitudinal axis was level and parallel to the track of the motor-driven torch carrier. Two cuts were made, one 2 in. above the longitudinal axis and the other 2 in. below. The time required to make each cut was approximately 75 min. The cutting operation is shown in Figs. z and 3. The 4-in. thick slab was mmediately charged into a furnace standing at 1200°F.

Jan 1, 1944

By Arthur C. Simmons

Production of oil within the state of Pennsylvania in 1940 was slightly more than the 1939 total, and this increase was due entirely to the new flush Music Mountain field south and west of the main Bradford pool. The influence and magnitude of Music Mountain production will be separately described, inasmuch as it is an important producing unit within the state. Production Bradford Field The production listed herein for Bradford field includes only the part of the field that is within the state of Pennsylvania. Approximately 4000 bbl. per day, or 10 per cent of the total Production of Bradford field comes from Cattaraugus County, New York, and should properly be attributed to production obtained within the New York state area, although locally and economically the Bradford field, situated both in New York State and Pennsylvania, is included as a single statistical unit. The 1940 average production in the Bradford field was 34,831 bbl. per day, as compared with a daily average in 1939 of 35,340 bbl., or a decrease from 1939 of 509 bbl. per day. The decrease in production from the Pennsylvania portion of the Bradford field would have been more pronounced if a portion of the crude from the Music Mountain field were not included with the statistics for Bradford field. The decline can be attributed largely to the fact that more properties of lower average recovery were being drilled in 1939 and 1940 than in previous years, and apparently a subnormal amount of drilling occurred in 1938 and 1939, when about 2100 wells were drilled each year. The full effect of the 1940 drilling is not felt immediately and undoubtedly will affect the producing period of 1941. It appears probable that the water-flood area in the Bradford field has reached a definite peak unless some unusual economic condition should cause abnormal prices and an excessive rate of development such as occurred in 1936 and 1937. Virtually all of the production in the Bradford field was obtained by water-flooding methods, as natural or stripper wells are uneconomical and air and gas repressuring have not proved so efficient as water-flooding as a secondary recovery method. Central and Southern Pennsylvania Central and southern Pennsylvania produced a total of 4,604,763 bbl. of oil during the calendar year of 1940; that is, an increase over the 1939 total of 166,728 bbl. The daily average production was 12,581 bbl., or an increase over 1939 of 422 bbl. per day. Table I includes the total oil production for the state of Pennsylvania for the years 1937 to 1940, inclusive, and the daily average for each of these years. It is impractical to make a complete subdivision by districts, consequently the only segregation is the production from the Bradford field (within the state of Penn-

Jan 1, 1941

By Arthur C. Simmons

Production of oil within the state of Pennsylvania in 1940 was slightly more than the 1939 total, and this increase was due entirely to the new flush Music Mountain field south and west of the main Bradford pool. The influence and magnitude of Music Mountain production will be separately described, inasmuch as it is an important producing unit within the state. Production Bradford Field The production listed herein for Bradford field includes only the part of the field that is within the state of Pennsylvania. Approximately 4000 bbl. per day, or 10 per cent of the total Production of Bradford field comes from Cattaraugus County, New York, and should properly be attributed to production obtained within the New York state area, although locally and economically the Bradford field, situated both in New York State and Pennsylvania, is included as a single statistical unit. The 1940 average production in the Bradford field was 34,831 bbl. per day, as compared with a daily average in 1939 of 35,340 bbl., or a decrease from 1939 of 509 bbl. per day. The decrease in production from the Pennsylvania portion of the Bradford field would have been more pronounced if a portion of the crude from the Music Mountain field were not included with the statistics for Bradford field. The decline can be attributed largely to the fact that more properties of lower average recovery were being drilled in 1939 and 1940 than in previous years, and apparently a subnormal amount of drilling occurred in 1938 and 1939, when about 2100 wells were drilled each year. The full effect of the 1940 drilling is not felt immediately and undoubtedly will affect the producing period of 1941. It appears probable that the water-flood area in the Bradford field has reached a definite peak unless some unusual economic condition should cause abnormal prices and an excessive rate of development such as occurred in 1936 and 1937. Virtually all of the production in the Bradford field was obtained by water-flooding methods, as natural or stripper wells are uneconomical and air and gas repressuring have not proved so efficient as water-flooding as a secondary recovery method. Central and Southern Pennsylvania Central and southern Pennsylvania produced a total of 4,604,763 bbl. of oil during the calendar year of 1940; that is, an increase over the 1939 total of 166,728 bbl. The daily average production was 12,581 bbl., or an increase over 1939 of 422 bbl. per day. Table I includes the total oil production for the state of Pennsylvania for the years 1937 to 1940, inclusive, and the daily average for each of these years. It is impractical to make a complete subdivision by districts, consequently the only segregation is the production from the Bradford field (within the state of Penn-

Jan 1, 1941